MD Danish Anwar says:
====================
Introduce ICSSG based ethernet Driver
The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like the implementation
of custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
The subsystem includes many accelerators for data processing like
multiplier and multiplier-accumulator. It also has peripherals like
UART, MII/RGMII, MDIO, etc. Every ICSSG core includes two 32-bit
load/store RISC CPU cores called PRUs.
The above features allow it to be used for implementing custom firmware
based peripherals like ethernet.
This series adds the YAML documentation and the driver with basic EMAC
support for TI AM654 Silicon Rev 2 SoC with the PRU_ICSSG Sub-system.
running dual-EMAC firmware.
This currently supports basic EMAC with 1Gbps and 100Mbps link. 10M and
half-duplex modes are not yet supported because they require the support
of an IEP, which will be added later.
Advanced features like switch-dev and timestamping will be added later.
This is the v13 of the patch series [v1]. This version of the patchset
addresses comments made on v12.
There series doesn't have any dependency.
Changes from v12 to v13 :
*) Rebased the series on latest net-next.
*) Addressed Jakub's comments on ndo_xmit API. Now we will only stop queues
based on occupancy not on dma errors.
*) Removed limiting the number of serviced packets to budget for Tx NAPI.
Now Tx NAPI will keep servicing packets.
*) Removed netif_running() check when packet arrives.
*) Introduced prototypes of APIs in the same patch where these APIs are added.
Dropped __maybe_unused tags as compiler only cares about prototypes
existing, not whether actual callers are in place. Now prototypes of these
APIs are present in the same patch where they are introduced but thes APIs
are called later (in patch 6).
Changes from v11 to v12 :
*) Rebased the series on latest net-next.
*) Addressed Jakub's comments on ndo_xmit API.
*) Added hooks to .get_rmon_stats for the driver. Now tx / rx bucket size
and frame counts per bucket will be fetched by ethtool_rmon_stats instead
of ethtool -S.
*) Added __maybe_unused tags to unused config and classifier APIs in patch
2,3 and 4. These tags are later removed in patch 6.
Changes from v10 to v11 :
*) Rebased the series on latest net-next.
*) Split the ICSSG driver introduction patch into 9 different patches as
asked by Jakub.
*) Introduced new patch(patch 8/10) to dump Standard network interface
staticstics via ndo_get_stats64. Now certain stats that are reported by
ICSSG hardware and are also part of struct rtnl_link_stats64, will be
reported by ndo_get_stats64. While other stats that are not part of the
struct rtnl_link_stats64 will be reported by ethtool -S. These stats
are not duplicated.
Changes from v9 to v10 :
*) Rebased the series on latest net-next.
*) Moved 'ndev prueth->emac[mac] == emac' assignment to the end of function
prueth_netdev_init().
*) In unsupported phy_mode switch case instead of returning -EINVAL, store
the error code in ret and 'goto free'
Changes from v8 to v9 :
*) Rebased the series on latest net-next.
*) Fixed smatch and sparse warnings as pointed by Simon.
*) Fixed leaky ndev in prueth_netdev_init() as asked by Simon.
Changes from v7 to v8 :
*) Rebased the series on 6.5-rc1.
*) Fixed few formattings.
Changes from v6 to v7 :
*) Added RB tag of Rob in patch 1 of this series.
*) Addressed Simon's comment on patch 2 of the series.
*) Rebased patchset on next-20230428 linux-next.
Changes from v5 to v6 :
*) Added RB tag of Andrew Lunn in patch 2 of this series.
*) Addressed Rob's comment on patch 1 of the series.
*) Rebased patchset on next-20230421 linux-next.
Changes from v4 to v5 :
*) Re-arranged properties section in ti,icssg-prueth.yaml file.
*) Added requirement for minimum one ethernet port.
*) Fixed some minor formatting errors as asked by Krzysztof.
*) Dropped SGMII mode from enum mii_mode as SGMII mode is not currently
supported by the driver.
*) Added switch-case block to handle different phy modes by ICSSG driver.
Changes from v3 to v4 :
*) Addressed Krzysztof's comments and fixed dt_binding_check errors in
patch 1/2.
*) Added interrupt-extended property in ethernet-ports properties section.
*) Fixed comments in file icssg_switch_map.h according to the Linux coding
style in patch 2/2. Added Documentation of structures in patch 2/2.
Changes from v2 to v3 :
*) Addressed Rob and Krzysztof's comments on patch 1 of this series.
Fixed indentation. Removed description and pinctrl section from
ti,icssg-prueth.yaml file.
*) Addressed Krzysztof, Paolo, Randy, Andrew and Christophe's comments on
patch 2 of this seires.
*) Fixed blanklines in Kconfig and Makefile. Changed structures to const
as suggested by Krzysztof.
*) Fixed while loop logic in emac_tx_complete_packets() API as suggested
by Paolo. Previously in the loop's last iteration 'budget' was 0 and
napi_consume_skb would wrongly assume the caller is not in NAPI context
Now, budget won't be zero in last iteration of loop.
*) Removed inline functions addr_to_da1() and addr_to_da0() as asked by
Andrew.
*) Added dev_err_probe() instead of dev_err() as suggested by Christophe.
*) In ti,icssg-prueth.yaml file, in the patternProperties section of
ethernet-ports, kept the port name as "port" instead of "ethernet-port"
as all other drivers were using "port". Will change it if is compulsory
to use "ethernet-port".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend / resume APIs to support power management in ICSSG ethernet
driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_stats.c to help dump, icssg related driver statistics.
ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, etc. These registers are of 32 bits and hence in case of 1G
link, they overflows in around 32 seconds. The behaviour of these registers
is such that they don't roll back to 0 after overflow but rather stay at
UINT_MAX.
These registers support a feature where the value written to them is
subtracted from the register. This feature can be utilized to fix the
overflowing of stats.
This solution uses a Workqueues based solution where a function gets
called before the registers overflow (every 25 seconds in 1G link, 25000
seconds in 100M link), this function saves the register
values in local variables and writes the last read value to the
register. So any update during the read will be taken care of.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Ethernet driver for TI AM654 Silicon rev. 2
with the ICSSG PRU Sub-system running dual-EMAC firmware.
The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like implementation of
custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
Every ICSSG core has two Programmable Real-Time Unit(PRUs),
two auxiliary Real-Time Transfer Unit (RT_PRUs), and
two Transmit Real-Time Transfer Units (TX_PRUs). Each one of these runs
its own firmware. Every ICSSG core has two MII ports connect to these
PRUs and also a MDIO port.
The cores can run different firmwares to support different protocols and
features like switch-dev, timestamping, etc.
It uses System DMA to transfer and receive packets and
shared memory register emulation between the firmware and
driver for control and configuration.
This patch adds support for basic EMAC functionality with 1Gbps
and 100Mbps link speed. 10M and half duplex mode are not supported
currently as they require IEP, the support for which will be added later.
Support for switch-dev, timestamp, etc. will be added later
by subsequent patch series.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a YAML binding document for the ICSSG Programmable real time unit
based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer
APIs to interface the PRUs and load/run the firmware for supporting
ethernet functionality.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. These will be used by
ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MII helper APIs and MACROs. These APIs and MACROs will be later used
by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has
definition of prueth related structures.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes XAUI/RXAUI lane alignment errors.
Issue causes dropped packets when trying to communicate over
fiber via SERDES lanes of port 9 and 10.
Errata document applies only to 88E6190X and 88E6390X devices.
Requires poking in undocumented registers.
Signed-off-by: Ante Knezic <ante.knezic@helmholz.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ratheesh Kannoth says:
====================
Packet classify by matching against SPI
1. net: flow_dissector: Add IPSEC dissector.
Flow dissector patch reads IPSEC headers (ESP or AH) header
from packet and retrieves the SPI header.
2. tc: flower: support for SPI.
TC control path changes to pass SPI field from userspace to
kernel.
3. tc: flower: Enable offload support IPSEC SPI field.
Next patch enables the HW support for classify offload for ESP/AH.
This patch enables the HW offload control.
4. octeontx2-pf: TC flower offload support for SPI field.
HW offload support for classification in octeontx2 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver support to offload TC flower rules which matches
against SPI field of IPSEC packets (AH/ESP).
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables offload for TC classifier
flower rules which matches against SPI field.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc flower rules support to classify ESP/AH
packets matching SPI field.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for dissecting IPSEC field SPI (which is
32bits in size) for ESP and AH packets.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong says:
====================
net: ethernet: dwmac: oxnas glue removal
With [1] removing MPCore SMP support, this makes the OX820 barely usable,
associated with a clear lack of maintainance, development and migration to
dt-schema it's clear that Linux support for OX810 and OX820 should be removed.
In addition, the OX810 hasn't been booted for years and isn't even present
in an ARM config file.
For the OX820, lack of USB and SATA support makes the platform not usable
in the current Linux support and relies on off-tree drivers hacked from the
vendor (defunct for years) sources.
The last users are in the OpenWRT distribution, and today's removal means
support will still be in stable 6.1 LTS kernel until end of 2026.
If someone wants to take over the development even with lack of SMP, I'll
be happy to hand off maintainance.
It has been a fun time adding support for this architecture, but it's time
to get over!
This patchset only removes net changes, and is derived from:
https://lore.kernel.org/r/20230630-topic-oxnas-upstream-remove-v2-0-fb6ab3dea87c@linaro.org
---
Changes in v3:
- Removed applied changes
- Added Andy's tags
- Reduced for net
- Link to v2: https://lore.kernel.org/r/20230630-topic-oxnas-upstream-remove-v2-0-fb6ab3dea87c@linaro.org
Changes in v2:
- s/maintainance/maintenance/
- added acked/review tags
- dropped already applied patches
- drop RFC
- Link to v1: https://lore.kernel.org/r/20230331-topic-oxnas-upstream-remove-v1-0-5bd58fd1dd1f@linaro.org
====================
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
selftests: New selftests for out-of-order-operations patches in mlxsw
In the past, the mlxsw driver made the assumption that the user applies
configuration in a bottom-up manner. Thus netdevices needed to be added to
the bridge before IP addresses were configured on that bridge or SVI added
on top of it, because whatever happened before a netdevice was mlxsw upper
was generally ignored by mlxsw. Recently, several patch series were pushed
to introduce the bookkeeping and replays necessary to offload the full
state, not just the immediate configuration step.
In this patchset, introduce new selftests that directly exercise the out of
order code paths in mlxsw.
- Patch #1 adds new tests into the existing selftest router_bridge.sh.
- Patches #2-#5 add new generic selftests.
- Patches #6-#8 add new mlxsw-specific selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This test verifies driver behavior with regards to creation of RIFs for a
bridge as LAGs are added or removed to/from it, and ports added or removed
to/from the LAG.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test verifies driver behavior with regards to creation of RIFs for LAG
VLAN uppers as ports are added or removed to/from the LAG.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test verifies driver behavior with regards to creation of RIFs for a
LAG as ports are added or removed to/from it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest to verify that routing through several bridges works when
LAG VLANs are used instead of physical ports, and that routing through LAG
VLANs themselves works as physical ports are de/enslaved.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest to verify that routing through a bridge works when LAG is
used instead of physical ports.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest to verify that routing through a 1d bridge works when VLAN
upper of a physical port is used instead of a physical port. Also verify
that when a port is attached to an already-configured bridge, the
configuration is applied.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two tests to deslave a port from and reenslave to a bridge. This should
retain the ability of the system to forward traffic, but on an offloading
driver that is sensitive to ordering of operations, it might not.
The first test does this configuration in a way that relies on
vlan_default_pvid to assign the PVID. The second test disables that
autoconfiguration and configures PVID by hand in a separate step.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XGMAC versions < 2.2 number of supported mdio C22 addresses is
restricted to 3. From XGMAC version 2.2 there are no restrictions on
the C22 addresses, it supports all valid mdio addresses(0 to 31).
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Acked-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Radu Pirea says:
====================
Add TJA1120 support
This patch series got bigger than I expected. It cleans up the
next-c45-tja11xx driver and adds support for the TJA1120(1000BaseT1
automotive phy).
Master/slave custom implementation was replaced with the generic
implementation (genphy_c45_config_aneg/genphy_c45_read_status).
The TJA1120 and TJA1103 are a bit different when it comes to the PTP
interface. The timestamp read procedure was changed, some addresses were
changed and some bits were moved from one register to another. Adding
TJA1120 support was tricky, and I tried not to duplicate the code. If
something looks too hacky to you, I am open to suggestions.
====================
Link: https://lore.kernel.org/r/20230731091619.77961-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During PTP testing on early TJA1120 engineering samples I observed that
if the link is lost and recovered, the tx timestamps will be randomly
lost. To avoid this HW issue, the PCS should be reset.
Resetting the PCS will break the link and we should reset the PCS on
LINK UP -> LINK DOWN transition, otherwise we will trigger and infinite
loop of LINK UP -> LINK DOWN events.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-12-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On TJA1120, the external trigger timestamp now has a VALID bit. This
changes the logic and we can't use the TJA1103 procedure.
For TJA1103, we can always read a valid timestamp from the registers,
compare the new timestamp with the old timestamp and, if they are not the
same, an event occurred. This logic cannot be applied for TJA1120 because
the timestamp is 0 if the VALID bit is not set.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230731091619.77961-11-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The egress timestamp FIFO/circular buffer work different on TJA1120 than
TJA1103.
For TJA1103 the new timestamp should be manually moved from the FIFO to
the hardware buffer before checking if the timestamp is valid.
For TJA1120 the hardware will move automatically the new timestamp
from the FIFO to the buffer and the user should check the valid bit, read
the timestamp and unlock the buffer by writing any of the buffer
registers(which are read only).
Another change for the TJA1120 is the behaviour of the EGR TS IRQ bit.
This bit was a self-clear bit for TJA1103, but now should be cleared
before reading the timestamp.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230731091619.77961-8-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PHY_BASIC_T1_FEATURES are not the right features supported by TJA1103
anymore.
For example ethtool reports:
[root@alarm ~]# ethtool end0
Settings for end0:
Supported ports: [ TP ]
Supported link modes: 100baseT1/Full
10baseT1L/Full
10baseT1L/Full is not supported by TJA1103 and supported ports list is
not completed. The PHY also have a MII port.
genphy_c45_pma_read_abilities implementation can detect the PHY features
and they look like this.
[root@alarm ~]# ethtool end0
Settings for end0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT1/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseT1/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
master-slave cfg: forced master
master-slave status: master
Port: Twisted Pair
PHYAD: 1
Transceiver: external
MDI-X: Unknown
Supports Wake-on: g
Wake-on: d
Link detected: yes
SQI: 7/7
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731091619.77961-5-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Between TJA1120 and TJA1103 the hardware was improved, but some register
addresses were changed and some bit fields were moved from one register
to another.
Introduce the nxp_c45_reg_field structure and its associated functions to
abstract the differences between the PHYs.
Remove the defined bits and register addresses that are not common
between TJA1103 and TJA1120 and replace them with reg_fields and
register addresses from phydev->drv->driver_data.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Link: https://lore.kernel.org/r/20230731091619.77961-4-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gavin Li says:
====================
virtio_net: add per queue interrupt coalescing support
Currently, coalescing parameters are grouped for all transmit and receive
virtqueues. This patch series add support to set or get the parameters for
a specified virtqueue.
When the traffic between virtqueues is unbalanced, for example, one virtqueue
is busy and another virtqueue is idle, then it will be very useful to
control coalescing parameters at the virtqueue granularity.
Example command:
$ ethtool -Q eth5 queue_mask 0x1 --coalesce tx-packets 10
Would set max_packets=10 to VQ 1.
$ ethtool -Q eth5 queue_mask 0x1 --coalesce rx-packets 10
Would set max_packets=10 to VQ 0.
$ ethtool -Q eth5 queue_mask 0x1 --show-coalesce
Queue: 0
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 222
rx-frames: 0
rx-usecs-irq: 0
rx-frames-irq: 256
tx-usecs: 222
tx-frames: 0
tx-usecs-irq: 0
tx-frames-irq: 256
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
====================
Link: https://lore.kernel.org/r/20230731070656.96411-1-gavinl@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add interrupt_coalesce config in send_queue and receive_queue to cache user
config.
Send per virtqueue interrupt moderation config to underlying device in
order to have more efficient interrupt moderation and cpu utilization of
guest VM.
Additionally, address all the VQs when updating the global configuration,
as now the individual VQs configuration can diverge from the global
configuration.
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20230731070656.96411-3-gavinl@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
