i2c-host updates for v6.15
Refactoring and cleanups
- octeon, cadence, i801, pasemi, mlxbf, bcm-iproc: general
refactorings
- octeon: remove 10-bit address support
Improvements
- amd-asf: improved error handling
- designware: use guard(mutex)
- amd-asf, designware: update naming to follow latest specs
- cadence: fix cleanup path in probe
- i801: use MMIO and I/O mapping helpers to access registers
- pxa: handle error after clk_prepare_enable
New features
- added i2c_10bit_addr_*_from_msg() and updated multiple drivers
- omap: added multiplexer state handling
- qcom-geni: update frequency configuration
- qup: introduce DMA usage policy
New hardware support
- exynos: add support for Samsung exynos7870
- k1: add support for spacemit k1 (new driver)
- imx: add support for i.mx94 lpi2c
- rk3x: add support for rk3562
Multiplexers
- ltc4306, reg: fix assignment in platform_driver structure
With the current settings, the I2C buses are achieving around 370KHz
instead of the expected 400KHz. For 100KHz and 1MHz, the settings are
now more compliant and adhere to the Qualcomm’s internal programming
guide.
Update the I2C frequency table to align with the recommended values
outlined in the I2C hardware programming guide, ensuring proper
communication and performance.
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20250122064634.2864432-1-quic_msavaliy@quicinc.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Switch to iomapped register access as a prerequisite for adding
support for MMIO register access.
This changes replaces the delayed inb_p()/outb_p() calls with calls to
ioread8()/iowrite8() which don't have this extra delay. According to
Documentation/driver-api/device-io.rst the _p versions are needed
for ISA device access only, therefore switching to the non-delayed
versions should not cause problems. However a certain risk remains,
which on the other hand is significantly reduced by the fact that
recent systems will use MMIO instead of PIO. ICH7 datasheet from 2012
mentions already that SMBus register space is also memory-mapped.
So all systems from at least the last 10 yrs should be safe.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/67535b17-c3fb-4507-b083-9c1884b4dd7d@gmail.com
In my tests terminating a transaction took about 25ms, what is
in line with the chip-internal timeout as described in 5.21.3.2
"Bus Time Out" in [0]. Therefore the 2ms delay is too low.
Instead of a fixed delay let's use i801_wait_intr() here,
this also facilitates the status handling.
This potential issue seems to have been existing forever, but as no
related problem is known, treat it as an improvement.
[0] Intel document #326776-003, 7 Series PCH datasheet
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/ad4ef645-5d03-4833-a0b6-f31f8fd06483@gmail.com
Clock handling can be very simplified with using devm_clk_get_enabled() as
was done by commit 8d2aaf4382 ("gpio: zynq: Simplify using
devm_clk_get_enabled()").
And also fix issue in connection to incorrect sequence when err_clk_dis
label is called.
When reset_control_deassert() fails it jumps to err_clk_dis label which
disables clock and also disable pm_runtime setup but nothing has been setup
at this time of failure because initialization is done below
reset_control_deassert() call.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250206115708.1085523-2-manikanta.guntupalli@amd.com
When the I2C QUP controller is used together with a DMA engine it needs
to vote for the interconnect path to the DRAM. Otherwise it may be
unable to access the memory quickly enough.
The requested peak bandwidth is dependent on the I2C core clock.
To avoid sending votes too often the bandwidth is always requested when
a DMA transfer starts, but dropped only on runtime suspend. Runtime
suspend should only happen if no transfer is active. After resumption we
can defer the next vote until the first DMA transfer actually happens.
The implementation is largely identical to the one introduced for
spi-qup in commit ecdaa94730 ("spi: qup: Vote for interconnect
bandwidth to DRAM") since both drivers represent the same hardware
block.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20231128-i2c-qup-dvfs-v1-3-59a0e3039111@kernkonzept.com
Building with W=1 shows a warning about ltc4306_of_match and
i2c_mux_reg_of_match being unused when CONFIG_OF is disabled:
drivers/i2c/muxes/i2c-mux-ltc4306.c:200:34: error: unused variable 'ltc4306_of_match' [-Werror,-Wunused-const-variable]
drivers/i2c/muxes/i2c-mux-reg.c:242:34: error: unused variable 'i2c_mux_reg_of_match' [-Werror,-Wunused-const-variable]
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250225163700.4169480-1-arnd@kernel.org
Refactor the current implementation of the high-level composite read and
write operations in preparation of the addition of block-mode read/write
operations.
The sending of the i2c command is generic and will apply for both the
block-mode and non-block-mode ops. Extract this from the current hlc
ops, and place into a generic function, octeon_i2c_hlc_cmd_send.
The considerations made for extended addresses in the command
construction are almost common for all cases, extract these into
octeon_i2c_hlc_ext. There is one difference between the extended read
and write cases. When performing extended read or writes the SW_TWSI_EXT
must be written with an extended internal address, but the data field is
only filled in the write case (read back in read case). This results in
the original code block for the read case immediately writing this
register, while the write case fills in any data and then writes the
register. To create a common block of code for both processes remove the
SW_TWSI_EXT write from within the code block and instead in it's place a
variable is set, set_ext, which is returned and used as a condition to
do the register write, in the read command case.
There are parts of the commands construction which are common (only in
the read case), extract this and place into generic function
octeon_i2c_hlc_read_cmd. This function also reads the return from
octeon_i2c_hlc_ext and completes the write to SW_TWSI_EXT if required.
The write commands cannot be made entirely into common code as there are
distinct differences in the block mode and non-block-mode process.
Particularly the writing of data into the buffer.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20241010025317.2040470-2-aryan.srivastava@alliedtelesis.co.nz
Pull media fix from Mauro Carvalho Chehab:
"rtl2832 driver regression fix"
* tag 'media/v6.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rtl2832_sdr: assign vb2 lock before vb2_queue_init
Pull i2c fixes from Wolfram Sang:
- omap: fix irq ACKS to avoid irq storming and system hang
- ali1535, ali15x3, sis630: fix error path at probe exit
* tag 'i2c-for-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sis630: Fix an error handling path in sis630_probe()
i2c: ali15x3: Fix an error handling path in ali15x3_probe()
i2c: ali1535: Fix an error handling path in ali1535_probe()
i2c: omap: fix IRQ storms
Pull tracing fix from Steven Rostedt:
"Fix ref count of trace_array in error path of histogram file open
Tracing instances have a ref count to keep them around while files
within their directories are open. This prevents them from being
deleted while they are used.
The histogram code had some files that needed to take the ref count
and that was added, but the error paths did not decrement the ref
counts. This caused the instances from ever being removed if a
histogram file failed to open due to some error"
* tag 'trace-v6.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Correct the refcount if the hist/hist_debug file fails to open
Pull USB fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes and new
usb-serial device ids. Included in here are:
- new usb-serial device ids
- typec driver bugfix
- thunderbolt driver resume bugfix
All of these have been in linux-next with no reported issues"
* tag 'usb-6.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: fix state transition for SNK_WAIT_CAPABILITIES state in run_state_machine()
USB: serial: ftdi_sio: add support for Altera USB Blaster 3
thunderbolt: Prevent use-after-free in resume from hibernate
USB: serial: option: fix Telit Cinterion FE990A name
USB: serial: option: add Telit Cinterion FE990B compositions
USB: serial: option: match on interface class for Telit FN990B
