Reserve memory for remote processors. Two memory regions are reserved
for each remote processor. The first 1Mb region is used for virtio
Vring buffers for IPC and the second region is used for holding
resource table, trace buffer and as external memory to the remote
processor. The mailboxes are also assigned for each remote processor.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20230502231527.25879-4-hnagalla@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The J784S4 SoCs have four TMS320C71x DSP subsystems in the MAIN voltage
domain. The functionality of these DSP subsystems is similar to the C71x
DSP subsystems on earlier k3 device J721S2. Each subsystem has a 48 KB of
L1D configurable SRAM/Cache and 512 KB of L2 SRAM/Cache. This subsystem
has a CMMU but is not currently used. The inter-processor communication
between the main A72 cores and the C71x DSPs is achieved through shared
memory and mailboxes. Add the DT nodes for these DSP processor sub-systems.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20230502231527.25879-3-hnagalla@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The J784S4 SoCs have 4 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining three clusters are present in the
MAIN domain (MAIN_R5FSS0, MAIN_R5FSS1 & MAIN_R5FSS2). The functionality
of the R5FSS is same as the R5FSS functionality on earlier K3 platform
device J721S2. Each of the R5FSS can be configured at boot time to be
either run in a LockStep mode or in an Asymmetric Multi Processing (AMP)
fashion in Split-mode. These subsystems have 64 KB each Tightly-Coupled
Memory (TCM) internal memories for each core split between two banks -
ATCM and BTCM (further interleaved into two banks). There are some IP
integration differences from standard Arm R5 clusters such as the absence
of an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT nodes for the R5F cluster/subsystems, the two R5F cores are
each added as child nodes to the corresponding cluster node. The clusters
are configured to run in LockStep mode by default, with the ATCMs enabled
to allow the R5 cores to execute code from DDR with boot-strapping code
from ATCM. The inter-processor communication between the main A72 cores
and these processors is achieved through shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if needed:
MAIN R5FSS0 Core0: j784s4-main-r5f0_0-fw (both in LockStep and Split modes)
MAIN R5FSS0 Core1: j784s4-main-r5f0_1-fw (needed only in Split mode)
MAIN R5FSS1 Core0: j784s4-main-r5f1_0-fw (both in LockStep and Split modes)
MAIN R5FSS1 Core1: j784s4-main-r5f1_1-fw (needed only in Split mode)
MAIN R5FSS2 Core0: j784s4-main-r5f2_0-fw (both in LockStep and Split modes)
MAIN R5FSS2 Core1: j784s4-main-r5f2_1-fw (needed only in Split mode)
MCU R5FSS0 Core0: j784s4-mcu-r5f0_0-fw (needed only in Split mode)
MCU R5FSS0 Core1: j784s4-mcu-r5f0_1-fw (needed only in Split mode)
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20230502231527.25879-2-hnagalla@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
wkup_uart and main_uart1 on this platform is used by tifs and DM
firmwares. Describe them for completeness including the pinmux.
Signed-off-by: Nishanth Menon <nm@ti.com>
[bb@ti.com: updated pinmux and commit subject]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20230425221708.549675-1-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
iot boards have always defined their own aliases and with the base-board
defining it's own aliases, there are no pending boards depending on
common aliases defined in SoC level.
aliases are meant to be defined appropriately based on the exposed
interfaces at a board level, drop the aliases defined at SoC level.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20230419225913.663448-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Similar to commit 3308a31c50 ("arm64: dts: ti: k3-am62: Add general
purpose timers for am62"), there are 12 general purpose timers on am62a7
split between 8 in main and 4 in mcu domains. The 4 in mcu domain do not
have interrupts that are routable to a53.
We configure the timers with the 25 MHz input clock by default as the
32.768 kHz clock may not be wired on the device. We leave the MCU domain
timers clock mux unconfigured, and mark the MCU domain timers reserved.
The MCU domain timers are likely reserved by the software for the ESM
module.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230418012717.1230882-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are 11 general purpose timers on am64 that can be used for things
like PWM using pwm-omap-dmtimer driver. There are also additional four
timers in the MCU domain that do not have interrupts routable for Linux.
We configure the timers with the 25 MHz input clock by default as the
32.768 kHz clock may not be wired on the device. We leave the MCU domain
timers clock mux unconfigured, and mark the MCU domain timers reserved.
The MCU domain timers are likely reserved by the software for the ESM
module.
Compared to am65, the timers on am64 do not have a dedicated IO mux for
the timers. On am62, the timers have different interrupts, clocks and
power domains compared to am65, and the MCU timers are at a different
IO address. Compared to AM62, the AM64 times have different clocks and
count in main domain are different as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230414073328.381336-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Pull perf tool updates from Arnaldo Carvalho de Melo:
"Third version of perf tool updates, with the build problems with with
using a 'vmlinux.h' generated from the main build fixed, and the bpf
skeleton build disabled by default.
Build:
- Require libtraceevent to build, one can disable it using
NO_LIBTRACEEVENT=1.
It is required for tools like 'perf sched', 'perf kvm', 'perf
trace', etc.
libtraceevent is available in most distros so installing
'libtraceevent-devel' should be a one-time event to continue
building perf as usual.
Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
sufficient for lots of users not interested in those libtraceevent
dependent features.
- Allow Python support in 'perf script' when libtraceevent isn't
linked, as not all features requires it, for instance Intel PT does
not use tracepoints.
- Error if the python interpreter needed for jevents to work isn't
available and NO_JEVENTS=1 isn't set, preventing a build without
support for JSON vendor events, which is a rare but possible
condition. The two check error messages:
$(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
$(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)
- Make libbpf 1.0 the minimum required when building with out of
tree, distro provided libbpf.
- Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
demangler, add 'perf test' entry for it.
- Make binutils libraries opt in, as distros disable building with it
due to licensing, they were used for C++ demangling, for instance.
- Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
equivalent) isn't installed, we'll just have a build warning:
Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev
- Add a feature test for scandirat(), that is not implemented so far
in musl and uclibc, disabling features that need it, such as
scanning for tracepoints in /sys/kernel/tracing/events.
perf BPF filters:
- New feature where BPF can be used to filter samples, for instance:
$ sudo ./perf record -e cycles --filter 'period > 1000' true
$ sudo ./perf script
perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)
- In addition to 'period' (PERF_SAMPLE_PERIOD), the other
PERF_SAMPLE_ can be used for filtering, and also some other sample
accessible values, from tools/perf/Documentation/perf-record.txt:
Essentially the BPF filter expression is:
<term> <operator> <value> (("," | "||") <term> <operator> <value>)*
The <term> can be one of:
ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
mem_dtlb, mem_blk, mem_hops
The <operator> can be one of:
==, !=, >, >=, <, <=, &
The <value> can be one of:
<number> (for any term)
na, load, store, pfetch, exec (for mem_op)
l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
remote (for mem_remote)
na, locked (for mem_locked)
na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
na, by_data, by_addr (for mem_blk)
hops0, hops1, hops2, hops3 (for mem_hops)
perf lock contention:
- Show lock type with address.
- Track and show mmap_lock, siglock and per-cpu rq_lock with address.
This is done for mmap_lock by following the current->mm pointer:
$ sudo ./perf lock con -abl -- sleep 10
contended total wait max wait avg wait address symbol
...
16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640
17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0
3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock
3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58
1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70
9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock
14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0
3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock
16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560
11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock
1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8
1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock
581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058
5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070
112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120
381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock
255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80
- Update default map size to 16384.
- Allocate single letter option -M for --map-nr-entries, as it is
proving being frequently used.
- Fix struct rq lock access for older kernels with BPF's CO-RE
(Compile once, run everywhere).
- Fix problems found with MSAn.
perf report/top:
- Add inline information when using --call-graph=fp or lbr, as was
already done to the --call-graph=dwarf callchain mode.
- Improve the 'srcfile' sort key performance by really using an
optimization introduced in 6.2 for the 'srcline' sort key that
avoids calling addr2line for comparision with each sample.
perf sched:
- Make 'perf sched latency/map/replay' to use "sched:sched_waking"
instead of "sched:sched_waking", consistent with 'perf record'
since d566a9c2d4 ("perf sched: Prefer sched_waking event when it
exists").
perf ftrace:
- Make system wide the default target for latency subcommand, run the
following command then generate some network traffic and press
control+C:
# perf ftrace latency -T __kfree_skb
^C
DURATION | COUNT | GRAPH |
0 - 1 us | 27 | ############# |
1 - 2 us | 22 | ########### |
2 - 4 us | 8 | #### |
4 - 8 us | 5 | ## |
8 - 16 us | 24 | ############ |
16 - 32 us | 2 | # |
32 - 64 us | 1 | |
64 - 128 us | 0 | |
128 - 256 us | 0 | |
256 - 512 us | 0 | |
512 - 1024 us | 0 | |
1 - 2 ms | 0 | |
2 - 4 ms | 0 | |
4 - 8 ms | 0 | |
8 - 16 ms | 0 | |
16 - 32 ms | 0 | |
32 - 64 ms | 0 | |
64 - 128 ms | 0 | |
128 - 256 ms | 0 | |
256 - 512 ms | 0 | |
512 - 1024 ms | 0 | |
1 - ... s | 0 | |
#
perf top:
- Add --branch-history (LBR: Last Branch Record) option, just like
already available for 'perf record'.
- Fix segfault in thread__comm_len() where thread->comm was being
used outside thread->comm_lock.
perf annotate:
- Allow configuring objdump and addr2line in ~/.perfconfig., so that
you can use alternative binaries, such as llvm's.
perf kvm:
- Add TUI mode for 'perf kvm stat report'.
Reference counting:
- Add reference count checking infrastructure to check for use after
free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
more to come.
To build with it use -DREFCNT_CHECKING=1 in the make command line
to build tools/perf. Documented at:
https://perf.wiki.kernel.org/index.php/Reference_Count_Checking
- The above caught, for instance, fix, present in this series:
- Fix maps use after put in 'perf test "Share thread maps"':
'maps' is copied from leader, but the leader is put on line 79
and then 'maps' is used to read the reference count below - so
a use after put, with the put of maps happening within
thread__put.
Fixed by reversing the order of puts so that the leader is put
last.
- Also several fixes were made to places where reference counts were
not being held.
- Make this one of the tests in 'make -C tools/perf build-test' to
regularly build test it and to make sure no direct access to the
reference counted structs are made, doing that via accessors to
check the validity of the struct pointer.
ARM64:
- Fix 'perf report' segfault when filtering coresight traces by
sparse lists of CPUs.
- Add support for 'simd' as a sort field for 'perf report', to show
ARM's NEON SIMD's predicate flags: "partial" and "empty".
arm64 vendor events:
- Add N1 metrics.
Intel vendor events:
- Add graniterapids, grandridge and sierraforrest events.
- Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
silvermont, skylake, tigerlake and westmereep-dp
- Refresh metrics for alderlake-n, broadwell, broadwellde,
broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
skylakex.
perf stat:
- Implement --topdown using JSON metrics.
- Add TopdownL1 JSON metric as a default if present, but disable it
for now for some Intel hybrid architectures, a series of patches
addressing this is being reviewed and will be submitted for v6.5.
- Use metrics for --smi-cost.
- Update topdown documentation.
Vendor events (JSON) infrastructure:
- Add support for computing and printing metric threshold values. For
instance, here is one found in thesapphirerapids json file:
{
"BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
"MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
"MetricGroup": "smi",
"MetricName": "smi_cycles",
"MetricThreshold": "smi_cycles > 0.1",
"ScaleUnit": "100%"
},
- Test parsing metric thresholds with the fake PMU in 'perf test
pmu-events'.
- Support for printing metric thresholds in 'perf list'.
- Add --metric-no-threshold option to 'perf stat'.
- Add rand (reverse and) and has_pmem (optane memory) support to
metrics.
- Sort list of input files to avoid depending on the order from
readdir() helping in obtaining reproducible builds.
S/390:
- Add common metrics: - CPI (cycles per instruction), prbstate (ratio
of instructions executed in problem state compared to total number
of instructions), l1mp (Level one instruction and data cache misses
per 100 instructions).
- Add cache metrics for z13, z14, z15 and z16.
- Add metric for TLB and cache.
ARM:
- Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
(Memory Tagging Extension) and MOPS (Memory Operations) load/store.
Intel PT hardware tracing:
- Add event type names UINTR (User interrupt delivered) and UIRET
(Exiting from user interrupt routine), documented in table 32-50
"CFE Packet Type and Vector Fields Details" in the Intel Processor
Trace chapter of The Intel SDM Volume 3 version 078.
- Add support for new branch instructions ERETS and ERETU.
- Fix CYC timestamps after standalone CBR
ARM CoreSight hardware tracing:
- Allow user to override timestamp and contextid settings.
- Fix segfault in dso lookup.
- Fix timeless decode mode detection.
- Add separate decode paths for timeless and per-thread modes.
auxtrace:
- Fix address filter entire kernel size.
Miscellaneous:
- Fix use-after-free and unaligned bugs in the PLT handling routines.
- Use zfree() to reduce chances of use after free.
- Add missing 0x prefix for addresses printed in hexadecimal in 'perf
probe'.
- Suppress massive unsupported target platform errors in the unwind
code.
- Fix return incorrect build_id size in elf_read_build_id().
- Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .
- Add missing new parameter in kfree_skb tracepoint to the python
scripts using it.
- Add 'perf bench syscall fork' benchmark.
- Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
'perf mem'.
- Fix wrong size expectation for perf test 'Setup struct
perf_event_attr' caused by the patch adding
perf_event_attr::config3.
- Fix some spelling mistakes"
* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
Revert "perf build: Warn for BPF skeletons if endian mismatches"
perf metrics: Fix SEGV with --for-each-cgroup
perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
perf stat: Separate bperf from bpf_profiler
perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
perf test record+probe_libc_inet_pton: Fix call chain match on s390
perf tracepoint: Fix memory leak in is_valid_tracepoint()
perf cs-etm: Add fix for coresight trace for any range of CPUs
perf build: Fix unescaped # in perf build-test
perf unwind: Suppress massive unsupported target platform errors
perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
perf script: Print raw ip instead of binary offset for callchain
perf symbols: Fix return incorrect build_id size in elf_read_build_id()
perf list: Modify the warning message about scandirat(3)
perf list: Fix memory leaks in print_tracepoint_events()
perf lock contention: Rework offset calculation with BPF CO-RE
perf lock contention: Fix struct rq lock access
perf stat: Disable TopdownL1 on hybrid
perf stat: Avoid SEGV on counter->name
...
Pull debugobjects fix from Thomas Gleixner:
"A single fix for debugobjects:
The recent fix to ensure atomicity of lookup and allocation
inadvertently broke the pool refill mechanism, so that debugobject
OOMs now in certain situations. The reason is that the functions which
got updated no longer invoke debug_objecs_init(), which is now the
only place to care about refilling the tracking object pool.
Restore the original behaviour by adding explicit refill opportunities
to those places"
* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debugobject: Ensure pool refill (again)
Pull crypto fixes from Herbert Xu:
- A long-standing bug in crypto_engine
- A buggy but harmless check in the sun8i-ss driver
- A regression in the CRYPTO_USER interface
* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Fix CRYPTO_USER checks for report function
crypto: engine - fix crypto_queue backlog handling
crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
Pull cifs fixes from Steve French:
"smb3 client fixes, mostly DFS or reconnect related:
- Two DFS connection sharing fixes
- DFS refresh fix
- Reconnect fix
- Two potential use after free fixes
- Also print prefix patch in mount debug msg
- Two small cleanup fixes"
* tag '6.4-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Remove unneeded semicolon
cifs: fix sharing of DFS connections
cifs: avoid potential races when handling multiple dfs tcons
cifs: protect access of TCP_Server_Info::{origin,leaf}_fullpath
cifs: fix potential race when tree connecting ipc
cifs: fix potential use-after-free bugs in TCP_Server_Info::hostname
cifs: print smb3_fs_context::source when mounting
cifs: protect session status check in smb2_reconnect()
SMB3.1.1: correct definition for app_instance_id create contexts
Pull clk fixes from Stephen Boyd:
"A couple more patches that would be good to get into -rc1:
- Revert an i.MX patch that's causing video failures because division
math goes sideways
- Fix a clang + W=1 build isue where FIELD_PREP() is taking a 32-bit
variable instead of the usual u64 type
- Fix a Kconfig bug in the StarFive JH7110 clk config that selects a
reset controller when it can't be selected"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: starfive: Fix RESET_STARFIVE_JH7110 can't be selected in a specified case
clk: sp7021: Adjust width of _m in HWM_FIELD_PREP()
Revert "clk: imx: composite-8m: Add support to determine_rate"
Pull mailbox updates from Jassi Brar:
- mailbox api: allow direct registration to a channel and convert omap
and pcc to use mbox_bind_client
- omap and hi6220 : use of_property_read_bool
- test: fix double-free and use spinlock header
- rockchip and bcm-pdc: drop of_match_ptr
- mpfs: change config symbol
- mediatek gce: support MT6795
- qcom apcs: consolidate of_device_id and support IPQ9574
* tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt-bindings: mailbox: qcom: add compatible for IPQ9574 SoC
mailbox: qcom-apcs-ipc: do not grow the of_device_id
dt-bindings: mailbox: qcom,apcs-kpss-global: use fallbacks for few variants
dt-bindings: mailbox: mediatek,gce-mailbox: Add support for MT6795
mailbox: mpfs: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE
mailbox: bcm-pdc: drop of_match_ptr for ID table
mailbox: rockchip: drop of_match_ptr for ID table
mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()
mailbox: mailbox-test: Explicitly include header for spinlock support
mailbox: Use of_property_read_bool() for boolean properties
mailbox: pcc: Use mbox_bind_client
mailbox: omap: Use mbox_bind_client
mailbox: Allow direct registration to a channel
Pull more io_uring updates from Jens Axboe:
"Nothing major in here, just two different parts:
- A small series from Breno that enables passing the full SQE down
for ->uring_cmd().
This is a prerequisite for enabling full network socket operations.
Queued up a bit late because of some stylistic concerns that got
resolved, would be nice to have this in 6.4-rc1 so the dependent
work will be easier to handle for 6.5.
- Fix for the huge page coalescing, which was a regression introduced
in the 6.3 kernel release (Tobias)"
* tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux:
io_uring: Remove unnecessary BUILD_BUG_ON
io_uring: Pass whole sqe to commands
io_uring: Create a helper to return the SQE size
io_uring/rsrc: check for nonconsecutive pages
This reverts commit a980755beb.
We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This reverts commit 51924ae69e.
We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull dmapool updates - again - from Andrew Morton:
"Reinstate the dmapool changes which were accidentally removed by a
mishap on the last commit in the previous attempt at the series"
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup").
[ The whole old series: def8574308ed..2d55c16c0c54 results in an empty
diff because that last commit ended up being just a revert of all that
came everything before it. - Linus ]
* tag 'mm-stable-2023-05-06-10-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
dmapool: link blocks across pages
dmapool: don't memset on free twice
dmapool: simplify freeing
dmapool: consolidate page initialization
dmapool: rearrange page alloc failure handling
dmapool: move debug code to own functions
dmapool: speedup DMAPOOL_DEBUG with init_on_alloc
dmapool: cleanup integer types
dmapool: use sysfs_emit() instead of scnprintf()
dmapool: remove checks for dev == NULL
Pull hotfixes from Andrew Morton:
"Five hotfixes.
Three are cc:stable, two pertain to merge window changes"
* tag 'mm-hotfixes-stable-2023-05-06-10-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
afs: fix the afs_dir_get_folio return value
nilfs2: do not write dirty data after degenerating to read-only
mm: do not reclaim private data from pinned page
nilfs2: fix infinite loop in nilfs_mdt_get_block()
mm/mmap/vma_merge: always check invariants
The allocated dmapool pages are never freed for the lifetime of the pool.
There is no need for the two level list+stack lookup for finding a free
block since nothing is ever removed from the list. Just use a simple
stack, reducing time complexity to constant.
The implementation inserts the stack linking elements and the dma handle
of the block within itself when freed. This means the smallest possible
dmapool block is increased to at most 16 bytes to accommodate these
fields, but there are no exisiting users requesting a dma pool smaller
than that anyway.
Removing the list has a significant change in performance. Using the
kernel's micro-benchmarking self test:
Before:
# modprobe dmapool_test
dmapool test: size:16 blocks:8192 time:57282
dmapool test: size:64 blocks:8192 time:172562
dmapool test: size:256 blocks:8192 time:789247
dmapool test: size:1024 blocks:2048 time:371823
dmapool test: size:4096 blocks:1024 time:362237
After:
# modprobe dmapool_test
dmapool test: size:16 blocks:8192 time:24997
dmapool test: size:64 blocks:8192 time:26584
dmapool test: size:256 blocks:8192 time:33542
dmapool test: size:1024 blocks:2048 time:9022
dmapool test: size:4096 blocks:1024 time:6045
The module test allocates quite a few blocks that may not accurately
represent how these pools are used in real life. For a more marco level
benchmark, running fio high-depth + high-batched on nvme, this patch shows
submission and completion latency reduced by ~100usec each, 1% IOPs
improvement, and perf record's time spent in dma_pool_alloc/free were
reduced by half.
[kbusch@kernel.org: push new blocks in ascending order]
Link: https://lkml.kernel.org/r/20230221165400.1595247-1-kbusch@meta.com
Link: https://lkml.kernel.org/r/20230126215125.4069751-12-kbusch@meta.com
Fixes: 2d55c16c0c ("dmapool: create/destroy cleanup")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
