We need wdev_chandef() in this code, which now requires
the wdev mutex due to the per-link nature. Hold it here
to make sure we can access the link.
Reported-by: syzbot+b4e9aa0f32ffd9902442@syzkaller.appspotmail.com
Fixes: 7b0a0e3c3a ("wifi: cfg80211: do some rework towards MLO link APIs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prior to commit 7b0a0e3c3a ("wifi: cfg80211: do some
rework towards MLO link APIs") the interface type didn't
really matter here, but now we need to handle all of the
possible cases. Add IBSS ("ADHOC") and handle it.
Fixes: 7b0a0e3c3a ("wifi: cfg80211: do some rework towards MLO link APIs")
Reported-by: syzbot+90d912872157e63589e4@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface isn't (yet) added to the driver, skip the
link info update. This was previously done for the BSS info
changes, but I forgot to copy the same check here.
Fixes: 7b7090b4c6 ("wifi: mac80211: split bss_info_changed method")
Reported-by: syzbot+bce2ca140cc00578ed07@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a client does not generate any local tx activity, accumulating airtime
deficit for the round-robin scheduler can be harmful. If this goes on for too
long, the deficit could grow quite large, which might cause unreasonable
initial latency once the client becomes active
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-7-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to maintain fairness, the amount of queueing needs to be limited
beyond the simple per-station AQL budget, otherwise the driver can simply
repeatedly do scheduling rounds until all queues that have not used their
AQL budget become eligble.
To be conservative, use the high AQL limit for the first txq and add half
of the low AQL for each subsequent queue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When queueing packets for a station, deficit only gets added once the packets
have been transmitted, which could be much later. During that time, a lot of
temporary unfairness could happen, which could lead to bursty behavior.
Fix this by subtracting the aql_tx_pending when checking the deficit in tx
scheduling.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow kernel-doc complains here about strong markup, but
we really don't need the [] so just remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently 17 kernel-doc warnings on this file:
include/net/cfg80211.h:391: warning: Function parameter or member 'bw' not described in 'ieee80211_eht_mcs_nss_supp'
include/net/cfg80211.h:437: warning: Function parameter or member 'eht_cap' not described in 'ieee80211_sband_iftype_data'
include/net/cfg80211.h:507: warning: Function parameter or member 's1g' not described in 'ieee80211_sta_s1g_cap'
include/net/cfg80211.h:1390: warning: Function parameter or member 'counter_offset_beacon' not described in 'cfg80211_color_change_settings'
include/net/cfg80211.h:1390: warning: Function parameter or member 'counter_offset_presp' not described in 'cfg80211_color_change_settings'
include/net/cfg80211.h:1430: warning: Enum value 'STATION_PARAM_APPLY_STA_TXPOWER' not described in enum 'station_parameters_apply_mask'
include/net/cfg80211.h:2195: warning: Function parameter or member 'dot11MeshConnectedToAuthServer' not described in 'mesh_config'
include/net/cfg80211.h:2341: warning: Function parameter or member 'short_ssid' not described in 'cfg80211_scan_6ghz_params'
include/net/cfg80211.h:3328: warning: Function parameter or member 'kck_len' not described in 'cfg80211_gtk_rekey_data'
include/net/cfg80211.h:3698: warning: Function parameter or member 'ftm' not described in 'cfg80211_pmsr_result'
include/net/cfg80211.h:3828: warning: Function parameter or member 'global_mcast_stypes' not described in 'mgmt_frame_regs'
include/net/cfg80211.h:4977: warning: Function parameter or member 'ftm' not described in 'cfg80211_pmsr_capabilities'
include/net/cfg80211.h:5742: warning: Function parameter or member 'u' not described in 'wireless_dev'
include/net/cfg80211.h:5742: warning: Function parameter or member 'links' not described in 'wireless_dev'
include/net/cfg80211.h:5742: warning: Function parameter or member 'valid_links' not described in 'wireless_dev'
include/net/cfg80211.h:6076: warning: Function parameter or member 'is_amsdu' not described in 'ieee80211_data_to_8023_exthdr'
include/net/cfg80211.h:6949: warning: Function parameter or member 'sig_dbm' not described in 'cfg80211_notify_new_peer_candidate'
Address them, in order to build a better documentation from this
header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/f6f522cdc716a01744bb0eae2186f4592976222b.1656409369.git.mchehab@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX BD (TX ring index) and TX WD (WiFi descriptor buffer) are freed
asynchronously. With burst packets, we free TX WD, but the corresponding
TX BD couldn't be freed yet. Then, TX can possibly get stuck due to no
more TX BD.
To avoid this, ignore reclaiming TX BD only if TX WD is no free space,
because at this moment TX BD must have some spaces. Otherwise, we reclaim
TX BD to resolve TX stuck issue.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-11-pkshih@realtek.com
In low power mode, regular IO is power off, so we don't schedule napi to
poll RX and TX completion. Therefore, calling ieee80211_rx_napi() with
napi instance causes long RX latency. To fix this, use NULL as argument,
and then it can use netif_receive_skb_list() to receive.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-10-pkshih@realtek.com
Some warning messages could bother users. With proper handling, these
situations don't really affect usage, but we still need to keep monitor
these messages. If they happen frequently, we must review driver or
hardware design to clarify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-8-pkshih@realtek.com
To improve VO throughput, we enable VO TX AMPDU.
We measure the latency of enable or disable VO TX AMPDU. The experimental
results show that the difference between the two is insignificant only
300µs, so the little impact can be ignored for user experience.
Moreover, we found some APs will have a group key handshake timeout issue
when the EAPOL's TID is already setup BA session. Therefore, when
transmitting EAPOL, if EAPOL's TID BA session is already setup, we need
to delete it.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220610072610.27095-7-pkshih@realtek.com
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab670 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com
The MLO links used for connection with an MLD AP are decided by the
driver in case of SME offloaded to driver.
Add support for the drivers to indicate the information of links used
for MLO connection in connect and roam callbacks, update the connected
links information in wdev from connect/roam result sent by driver.
Also, send the connected links information to userspace.
Add a netlink flag attribute to indicate that userspace supports
handling of MLO connection. Drivers must not do MLO connection when this
flag is not set. This is to maintain backwards compatibility with older
supplicant versions which doesn't have support for MLO connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add initial support to hwsim for creating MLO-capable
radios dynamically (and statically via module parameter,
but that's not really recommended.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When retrieving scan data, expose not just whether or not the
interface (possibly an MLD) is associated to the BSS or not,
but also on which link ID if it is an MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add to hwsim a link_data structure.
For now, move the beacon interval and beacon timer to
the link_data structure (making them per link).
Set a beacon timer for each link and transmit a per
link beacon (pass the link_id to ieee80211_beacon_get).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should set the STA deflink addresses in case no
link is really added.
Fixes: 046d2e7c50 ("mac80211: prepare sta handling for MLO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Maintain a hash table of link-sta addresses so we can find
them for management frames etc. where addresses haven't
been replaced by the drivers to the MLD address yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to access these in a race-free way under
traffic while adding/removing them, so RCU-ify the pointers.
This requires passing a link_sta to a lot of functions so
we don't have to do the RCU handling everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hardcoding link[0] is more confusing than using deflink,
so use deflink for now, which requires making the macro
a bit safer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use link and link_conf according to the link_id
provided by cfg in start_ap/stop_ap and change_beacon.
Also use them in the functions called by them.
Note that for a non MLD device, the link_id is 0,
and link[0] and link_conf[0] equal to deflink and
bss_conf respectively (what was there before).
Also, call vif_info_change for BSS related changes (SSID), and
link_info_change for LINK related changes (instead of the
legacy bss_info_change).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a link is added or removed via nl80211, these are
called. Implement them so we don't have to check in all
the different per-link commands whether we've already
created the necessary datastructures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some optional callbacks for link add/remove so that
drivers can react here. Initially, I thought it would be
sufficient to just create the link in start_ap etc., but
it turns out that's not so simple, since there are quite
a few callbacks that can be called: if they're erroneously
without start_ap, things might crash.
Thus it might be easier for drivers to allocate all the
necessary data structures immediately, to not have to
worry about it in each callback, since cfg80211 checks
that the link ID is valid (has been added.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We wanted to have this sorted by direction (to/from driver),
but didn't maintain that well. Sort the file now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from a station. To do this,
refactor the link alloc/free a bit, splitting that so we
can do it without linking them, to handle failures better.
Note that a station entry must be created representing an
MLD or a non-MLD STA, it cannot change between the two.
When representing an MLD, the 'deflink' is used for the
first link, which might be removed later, in which case
the memory isn't reused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Take a few bits out of the control.flags to add the link ID
to TX frame metadata, so drivers don't need to look it up
by the address themselves. Implement that lookup where it's
needed, for internal frame TX, and set it to "unspecified"
for data transmissions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface is an MLD, then we don't know which band
the frame will be transmitted on, and we don't know how to
look up the band. Set the band information to zero in that
case, the driver cannot rely on it anyway.
No longer inline ieee80211_tx_skb_tid() since it's even
bigger now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from an interface.
Also add the missing link address to bss_conf (which we
use as link_conf too), and fill it, in station mode for
now just randomly, in AP mode we get the address from
cfg80211 since the link must be created with an address
first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
