On Raspberry Pis without onboard USB hub frequent device reconnects
can trigger a interrupt storm after DWC2 entered host clock gating.
This is caused by a race between _dwc2_hcd_suspend() and the port
interrupt, which sets port_connect_status. The issue occurs if
port_connect_status is still 1, but there is no connection anymore:
usb 1-1: USB disconnect, device number 25
dwc2 3f980000.usb: _dwc2_hcd_suspend: port_connect_status: 1
dwc2 3f980000.usb: Entering host clock gating.
Disabling IRQ #66
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-gc1bb81b13202-dirty #322
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1d01f20 to 0xc1d01f68)
1f20: 0004ef3c 00000001 00000000 00000000 c1d09780 c1f6bb5c c1d04e54 c1c60ca8
1f40: c1d04e94 00000000 00000000 c1d092a8 c1f6af20 c1d01f70 c1211b98 c1212f40
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<e3a25c00>] dwc2_handle_common_intr
[<58bf98a3>] usb_hcd_irq
Disabling IRQ #66
So avoid this by reading the connection status directly.
Fixes: 113f86d0c3 ("usb: dwc2: Update partial power down entering by system suspend")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Raspberry Pi can suffer on interrupt storms on HCD resume. The dwc2
driver sometimes misses to enable HCD_FLAG_HW_ACCESSIBLE before re-enabling
the interrupts. This causes a situation where both handler ignore a incoming
port interrupt and force the upper layers to disable the dwc2 interrupt
line. This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
So enable the HCD_FLAG_HW_ACCESSIBLE flag in case there is a port
connection.
Fixes: c74c26f6e3 ("usb: dwc2: Fix partial power down exiting by system resume")
Closes: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB5744 SMBus initialization is done once in probe() and doing it in resume
is not supported so avoid going into suspend and reset the HUB.
There is a sysfs property 'always_powered_in_suspend' to implement this
feature but since default state should be set to a working configuration
so override this property value.
It fixes the suspend/resume testcase on Kria KR260 Robotics Starter Kit.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Cc: stable@vger.kernel.org
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1733165302-1694891-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the USB3 PHY is not defined in the Linux device tree, there could
still be a case where there is a USB3 PHY active on the board and enabled
by the first stage bootloader. If serdes clock is being used then the USB
will fail to enumerate devices in 2.0 only mode.
To solve this, make sure that the PIPE clock is deselected whenever the
USB3 PHY is not defined and guarantees that the USB2 only mode will work
in all cases.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/1733163111-1414816-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 53a2d95df8 ("usb: core: add phy notify connect and
disconnect"), phy initialization will be skipped even when shared hcd
doesn't set skip_phy_initialization flag. However, the situation is
changed after the commit. The hcd.c will initialize phy when add shared
hcd. This behavior is unexpected for some platforms which will handle phy
initialization by themselves. To avoid the issue, this will only check
skip_phy_initialization flag of primary hcd since shared hcd normally
follow primary hcd setting.
Fixes: 53a2d95df8 ("usb: core: add phy notify connect and disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241105090120.2438366-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UMP Function Block info m1.0 field (represented by is_midi1 sysfs
entry) is an enumeration from 0 to 2, while the midi2 gadget driver
incorrectly copies it to the corresponding snd_ump_block_info.flags
bits as-is. This made the wrong bit flags set when m1.0 = 2.
This patch corrects the wrong interpretation of is_midi1 bits.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20241127070213.8232-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbind and bind the device again, kernel will dump below warning:
[ 173.972130] sysfs: cannot create duplicate filename '/devices/platform/soc/4c010010.usb/software_node'
[ 173.981564] CPU: 2 UID: 0 PID: 536 Comm: sh Not tainted 6.12.0-rc6-06344-g2aed7c4a5c56 #144
[ 173.989923] Hardware name: NXP i.MX95 15X15 board (DT)
[ 173.995062] Call trace:
[ 173.997509] dump_backtrace+0x90/0xe8
[ 174.001196] show_stack+0x18/0x24
[ 174.004524] dump_stack_lvl+0x74/0x8c
[ 174.008198] dump_stack+0x18/0x24
[ 174.011526] sysfs_warn_dup+0x64/0x80
[ 174.015201] sysfs_do_create_link_sd+0xf0/0xf8
[ 174.019656] sysfs_create_link+0x20/0x40
[ 174.023590] software_node_notify+0x90/0x100
[ 174.027872] device_create_managed_software_node+0xec/0x108
...
The '4c010010.usb' device is a platform device created during the initcall
and is never removed, which causes its associated software node to persist
indefinitely.
The existing device_create_managed_software_node() does not provide a
corresponding removal function.
Replace device_create_managed_software_node() with the
device_add_software_node() and device_remove_software_node() pair to ensure
proper addition and removal of software nodes, addressing this issue.
Fixes: a9400f1979 ("usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241126032841.2458338-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The refcounts of the OF nodes obtained by of_get_child_by_name() calls
in anx7411_typec_switch_probe() are not decremented. Replace them with
device_get_named_child_node() calls and store the return values to the
newly created fwnode_handle fields in anx7411_data, and call
fwnode_handle_put() on them in the error path and in the unregister
functions.
Fixes: e45d7337dc ("usb: typec: anx7411: Use of_get_child_by_name() instead of of_find_node_by_name()")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241126014909.3687917-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the current USB request was aborted, the spi thread would not respond
to any further requests. This is because the "curr_urb" pointer would
not become NULL, so no further requests would be taken off the queue.
The solution here is to set the "urb_done" flag, as this will cause the
correct handling of the URB. Also clear interrupts that should only be
expected if an URB is in progress.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20241124221430.1106080-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c component probing support from Wolfram Sang:
"Add OF component probing.
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular
device can be detected by some firmware provided identifier, other
times that information is not available, and the kernel has to try to
probe each device.
Instead of a delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them
responds. It will then enable the device that responds"
* tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: fix typo in I2C OF COMPONENT PROBER
of: base: Document prefix argument for of_get_next_child_with_prefix()
i2c: Fix whitespace style issue
arm64: dts: mediatek: mt8173-elm-hana: Mark touchscreens and trackpads as fail
platform/chrome: Introduce device tree hardware prober
i2c: of-prober: Add GPIO support to simple helpers
i2c: of-prober: Add simple helpers for regulator support
i2c: Introduce OF component probe function
of: base: Add for_each_child_of_node_with_prefix()
of: dynamic: Add of_changeset_update_prop_string
Pull bprintf() removal from Steven Rostedt:
- Remove unused bprintf() function, that was added with the rest of the
"bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
* tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
printf: Remove unused 'bprintf'
Pull timer fixes from Borislav Petkov:
- Fix a case where posix timers with a thread-group-wide target would
miss signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function
__udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
* tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Target group sigqueue to current task only if not exiting
delay: Fix ndelay() spuriously treated as udelay()
ntp: Remove invalid cast in time offset math
Pull irq fixes from Borislav Petkov:
- Move the ->select callback to the correct ops structure in
irq-mvebu-sei to fix some Marvell Armada platforms
- Add a workaround for Hisilicon ITS erratum 162100801 which can cause
some virtual interrupts to get lost
- More platform_driver::remove() conversion
* tag 'irq_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Switch back to struct platform_driver::remove()
irqchip/gicv3-its: Add workaround for hip09 ITS erratum 162100801
irqchip/irq-mvebu-sei: Move misplaced select() callback to SEI CP domain
Pull x86 fixes from Borislav Petkov:
- Add a terminating zero end-element to the array describing AMD CPUs
affected by erratum 1386 so that the matching loop actually
terminates instead of going off into the weeds
- Update the boot protocol documentation to mention the fact that the
preferred address to load the kernel to is considered in the
relocatable kernel case too
- Flush the memory buffer containing the microcode patch after applying
microcode on AMD Zen1 and Zen2, to avoid unnecessary slowdowns
- Make sure the PPIN CPU feature flag is cleared on all CPUs if PPIN
has been disabled
* tag 'x86_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Terminate the erratum_1386_microcode array
x86/Documentation: Update algo in init_size description of boot protocol
x86/microcode/AMD: Flush patch buffer mapping after application
x86/mm: Carve out INVLPG inline asm for use by others
x86/cpu: Fix PPIN initialization
The point behind strscpy() was to once and for all avoid all the
problems with 'strncpy()' and later broken "fixed" versions like
strlcpy() that just made things worse.
So strscpy not only guarantees NUL-termination (unlike strncpy), it also
doesn't do unnecessary padding at the destination. But at the same time
also avoids byte-at-a-time reads and writes by _allowing_ some extra NUL
writes - within the size, of course - so that the whole copy can be done
with word operations.
It is also stable in the face of a mutable source string: it explicitly
does not read the source buffer multiple times (so an implementation
using "strnlen()+memcpy()" would be wrong), and does not read the source
buffer past the size (like the mis-design that is strlcpy does).
Finally, the return value is designed to be simple and unambiguous: if
the string cannot be copied fully, it returns an actual negative error,
making error handling clearer and simpler (and the caller already knows
the size of the buffer). Otherwise it returns the string length of the
result.
However, there was one final stability issue that can be important to
callers: the stability of the destination buffer.
In particular, the same way we shouldn't read the source buffer more
than once, we should avoid doing multiple writes to the destination
buffer: first writing a potentially non-terminated string, and then
terminating it with NUL at the end does not result in a stable result
buffer.
Yes, it gives the right result in the end, but if the rule for the
destination buffer was that it is _always_ NUL-terminated even when
accessed concurrently with updates, the final byte of the buffer needs
to always _stay_ as a NUL byte.
[ Note that "final byte is NUL" here is literally about the final byte
in the destination array, not the terminating NUL at the end of the
string itself. There is no attempt to try to make concurrent reads and
writes give any kind of consistent string length or contents, but we
do want to guarantee that there is always at least that final
terminating NUL character at the end of the destination array if it
existed before ]
This is relevant in the kernel for the tsk->comm[] array, for example.
Even without locking (for either readers or writers), we want to know
that while the buffer contents may be garbled, it is always a valid C
string and always has a NUL character at 'comm[TASK_COMM_LEN-1]' (and
never has any "out of thin air" data).
So avoid any "copy possibly non-terminated string, and terminate later"
behavior, and write the destination buffer only once.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull turbostat updates from Len Brown:
- assorted minor bug fixes
- assorted platform specific tweaks
- initial RAPL PSYS (SysWatt) support
* tag 'turbostat-2024.11.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: 2024.11.30
tools/power turbostat: Add RAPL psys as a built-in counter
tools/power turbostat: Fix child's argument forwarding
tools/power turbostat: Force --no-perf in --dump mode
tools/power turbostat: Add support for /sys/class/drm/card1
tools/power turbostat: Cache graphics sysfs file descriptors during probe
tools/power turbostat: Consolidate graphics sysfs access
tools/power turbostat: Remove unnecessary fflush() call
tools/power turbostat: Enhance platform divergence description
tools/power turbostat: Add initial support for GraniteRapids-D
tools/power turbostat: Remove PC3 support on Lunarlake
tools/power turbostat: Rename arl_features to lnl_features
tools/power turbostat: Add back PC8 support on Arrowlake
tools/power turbostat: Remove PC7/PC9 support on MTL
tools/power turbostat: Honor --show CPU, even when even when num_cpus=1
tools/power turbostat: Fix trailing '\n' parsing
tools/power turbostat: Allow using cpu device in perf counters on hybrid platforms
tools/power turbostat: Fix column printing for PMT xtal_time counters
tools/power turbostat: fix GCC9 build regression
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
Pull ima fix from Paul Moore:
"One small patch to fix a function parameter / local variable naming
snafu that went up to you in the current merge window"
* tag 'lsm-pr-20241129' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
ima: uncover hidden variable in ima_match_rules()
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Use correct srcu list traversal (Breno)
- Scatter-gather support for metadata (Keith)
- Fabrics shutdown race condition fix (Nilay)
- Persistent reservations updates (Guixin)
- Add the required bits for MD atomic write support for raid0/1/10
- Correct return value for unknown opcode in ublk
- Fix deadlock with zone revalidation
- Fix for the io priority request vs bio cleanups
- Use the correct unsigned int type for various limit helpers
- Fix for a race in loop
- Cleanup blk_rq_prep_clone() to prevent uninit-value warning and make
it easier for actual humans to read
- Fix potential UAF when iterating tags
- A few fixes for bfq-iosched UAF issues
- Fix for brd discard not decrementing the allocated page count
- Various little fixes and cleanups
* tag 'block-6.13-20242901' of git://git.kernel.dk/linux: (36 commits)
brd: decrease the number of allocated pages which discarded
block, bfq: fix bfqq uaf in bfq_limit_depth()
block: Don't allow an atomic write be truncated in blkdev_write_iter()
mq-deadline: don't call req_get_ioprio from the I/O completion handler
block: Prevent potential deadlock in blk_revalidate_disk_zones()
block: Remove extra part pointer NULLify in blk_rq_init()
nvme: tuning pr code by using defined structs and macros
nvme: introduce change ptpl and iekey definition
block: return bool from get_disk_ro and bdev_read_only
block: remove a duplicate definition for bdev_read_only
block: return bool from blk_rq_aligned
block: return unsigned int from blk_lim_dma_alignment_and_pad
block: return unsigned int from queue_dma_alignment
block: return unsigned int from bdev_io_opt
block: req->bio is always set in the merge code
block: don't bother checking the data direction for merges
block: blk-mq: fix uninit-value in blk_rq_prep_clone and refactor
Revert "block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()"
md/raid10: Atomic write support
md/raid1: Atomic write support
...
Pull more io_uring updates from Jens Axboe:
- Remove a leftover struct from when the cqwait registered waiting was
transitioned to regions.
- Fix for an issue introduced in this merge window, where nop->fd might
be used uninitialized. Ensure it's always set.
- Add capping of the task_work run in local task_work mode, to prevent
bursty and long chains from adding too much latency.
- Work around xa_store() leaving ->head non-NULL if it encounters an
allocation error during storing. Just a debug trigger, and can go
away once xa_store() behaves in a more expected way for this
condition. Not a major thing as it basically requires fault injection
to trigger it.
- Fix a few mapping corner cases
- Fix KCSAN complaint on reading the table size post unlock. Again not
a "real" issue, but it's easy to silence by just keeping the reading
inside the lock that protects it.
* tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux:
io_uring/tctx: work around xa_store() allocation error issue
io_uring: fix corner case forgetting to vunmap
io_uring: fix task_work cap overshooting
io_uring: check for overflows in io_pin_pages
io_uring/nop: ensure nop->fd is always initialized
io_uring: limit local tw done
io_uring: add io_local_work_pending()
io_uring/region: return negative -E2BIG in io_create_region()
io_uring: protect register tracing
io_uring: remove io_uring_cqwait_reg_arg
Pull dma-mapping fix from Christoph Hellwig:
- fix physical address calculation for struct dma_debug_entry (Fedor
Pchelkin)
* tag 'dma-mapping-6.13-2024-11-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix physical address calculation for struct dma_debug_entry
Pull more kvm updates from Paolo Bonzini:
- ARM fixes
- RISC-V Svade and Svadu (accessed and dirty bit) extension support for
host and guest
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: riscv: selftests: Add Svade and Svadu Extension to get-reg-list test
RISC-V: KVM: Add Svade and Svadu Extensions Support for Guest/VM
dt-bindings: riscv: Add Svade and Svadu Entries
RISC-V: Add Svade and Svadu Extensions Support
KVM: arm64: Use MDCR_EL2.HPME to evaluate overflow of hyp counters
KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
KVM: arm64: Mark set_sysreg_masks() as inline to avoid build failure
KVM: arm64: vgic-its: Add stronger type-checking to the ITS entry sizes
KVM: arm64: vgic: Kill VGIC_MAX_PRIVATE definition
KVM: arm64: vgic: Make vgic_get_irq() more robust
KVM: arm64: vgic-v3: Sanitise guest writes to GICR_INVLPIR
Pull sh updates from John Paul Adrian Glaubitz:
"Two small fixes.
The first one by Huacai Chen addresses a runtime warning when
CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS are selected
which occurs because the cpuinfo code on sh incorrectly uses NR_CPUS
when iterating CPUs instead of the runtime limit nr_cpu_ids.
A second fix by Dan Carpenter fixes a use-after-free bug in
register_intc_controller() which occurred as a result of improper
error handling in the interrupt controller driver code when
registering an interrupt controller during plat_irq_setup() on sh"
* tag 'sh-for-v6.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: intc: Fix use-after-free bug in register_intc_controller()
sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
Pull arm64 fixes from Catalin Marinas:
- Deselect ARCH_CORRECT_STACKTRACE_ON_KRETPROBE so that tests depending
on it don't run (and fail) on arm64
- Fix lockdep assert in the Arm SMMUv3 PMU driver
- Fix the port and device ID bits setting in the Arm CMN perf driver
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
perf/arm-cmn: Ensure port and device id bits are set properly
perf/arm-smmuv3: Fix lockdep assert in ->event_init()
arm64: disable ARCH_CORRECT_STACKTRACE_ON_KRETPROBE tests
since 2024.07.26:
assorted minor bug fixes
assorted platform specific tweaks
initial RAPL PSYS (SysWatt) support
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce the counter as a part of global, platform counters structure.
We open the counter for only one cpu, but otherwise treat it as an
ordinary RAPL counter, allowing for grouped perf read.
The counter is disabled by default, because it's interpretation may
require additional, platform specific information, making it unsuitable
for general use.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add '+' to optstring when early scanning for --no-msr and --no-perf.
It causes option processing to stop as soon as a nonoption argument is
encountered, effectively skipping child's arguments.
Fixes: 3e4048466c ("tools/power turbostat: Add --no-msr option")
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Force the --no-perf early to prevent using it as a source. User asks for
raw values, but perf returns them relative to the opening of the file
descriptor.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, the graphics device is enumerated as
/sys/class/drm/card1 instead of /sys/class/drm/card0. The current
implementation does not handle this scenario, resulting in the loss of
graphics C6 residency and frequency information.
Add support for /sys/class/drm/card1, ensuring that turbostat can
retrieve and display the graphics columns for these platforms.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Snapshots of the graphics sysfs knobs are taken based on file
descriptors. To optimize this process, open the files and cache the file
descriptors during the graphics probe phase. As a result, the previously
cached pathnames become redundant and are removed.
This change aims to streamline the code without altering its functionality.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, there is an inconsistency in how graphics sysfs knobs are
accessed: graphics residency sysfs knobs are opened and closed for each
read, while graphics frequency sysfs knobs are opened once and remain
open until turbostat exits. This inconsistency is confusing and adds
unnecessary code complexity.
Consolidate the access method by opening the sysfs files once and
reusing the file pointers for subsequent accesses. This approach
simplifies the code and ensures a consistent method for accessing
graphics sysfs knobs.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The graphics sysfs knobs are read-only, making the use of fflush()
before reading them redundant.
Remove the unnecessary fflush() call.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In various generations, platforms often share a majority of features,
diverging only in a few specific aspects. The current approach of using
hardcoded values in 'platform_features' structure fails to effectively
represent these divergences.
To improve the description of platform divergence:
1. Each newly introduced 'platform_features' structure must have a base,
typically derived from the previous generation.
2. Platform feature values should be inherited from the base structure
rather than being hardcoded.
This approach ensures a more accurate and maintainable representation of
platform-specific features across different generations.
Converts `adl_features` and `lnl_features` to follow this new scheme.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add initial support for GraniteRapids-D. It shares the same features
with SapphireRapids.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lunarlake supports CC1/CC6/CC7/PC2/PC6/PC10.
Remove PC3 support on Lunarlake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As ARL shares the same features with ADL/RPL/MTL, now 'arl_features' is
used by Lunarlake platform only.
Rename 'arl_features' to 'lnl_features'.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Similar to ADL/RPL/MTL, ARL supports CC1/CC6/CC7/PC2/PC3/PC6/PC8/PC10.
Add back PC8 support on Arrowlake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Similar to ADL/RPL, MTL support CC1/CC6/CC7/PC2/PC3/PC6/PC8/CP10.
Remove PC7/PC9 support on MTL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Honor --show CPU and --show Core when "topo.num_cpus == 1".
Previously turbostat assumed that on a 1-CPU system, these
columns should never appear.
Honoring these flags makes it easier for several programs
that parse turbostat output.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
parse_cpu_string() parses the string input either from command line or
from /sys/fs/cgroup/cpuset.cpus.effective to get a list of CPUs that
turbostat can run with.
The cpu string returned by /sys/fs/cgroup/cpuset.cpus.effective contains
a trailing '\n', but strtoul() fails to treat this as an error.
That says, for the code below
val = ("\n", NULL, 10);
val returns 0, and errno is also not set.
As a result, CPU0 is erroneously considered as allowed CPU and this
causes failures when turbostat tries to run on CPU0.
get_counters: Could not migrate to CPU 0
...
turbostat: re-initialized with num_cpus 8, allowed_cpus 5
get_counters: Could not migrate to CPU 0
Add a check to return immediately if '\n' or '\0' is detected.
Fixes: 8c3dd2c9e5 ("tools/power/turbostat: Abstrct function for parsing cpu string")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel hybrid platforms expose different perf devices for P and E cores.
Instead of one, "/sys/bus/event_source/devices/cpu" device, there are
"/sys/bus/event_source/devices/{cpu_core,cpu_atom}".
This, however makes it more complicated for the user,
because most of the counters are available on both and had to be
handled manually.
This patch allows users to use "virtual" cpu device that is seemingly
translated to cpu_core and cpu_atom perf devices, depending on the type
of a CPU we are opening the counter for.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
