Last set of Qualcomm ARM64 DTS updates for v6.3
This introduces additional DisplayPort controllers and pmic_glink on
SC8280XP (8cx Gen3), which provides support for USB Type-C-based
displays on the the Lenovo ThinkPad X13s and the compute reference
device. The pmic_glink also provides battery and power supply status.
Interrupt-parents are corrected across the SC8280XP PMICs, to allow
non-Linux OSs to properly handle interrupts in the various blocks
therein.
It cleans up the SM8350 base dtsi and introduces GPU support on this
platform, as well as enable this for the Hardware Development Kit (HDK).
It enables i2c busses on the Fairphone FP4
Lastly it aligns glink node names with bindings across a few platforms,
and corrects the compatible for the PON block in the pmk8350 PMIC.
* tag 'qcom-arm64-for-6.3-3' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
Link: https://lore.kernel.org/r/20230215051530.1165953-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nodes like pwrkey, resin, iadc, adc-tm, temp-alarm which are the grand
children of spmi_bus node represent the interrupt generating devices but
don't have "interrupt-parent" property.
As per the devicetree spec v0.3, section 2.4:
"The physical wiring of an interrupt source to an interrupt controller is
represented in the devicetree with the interrupt-parent property. Nodes
that represent interrupt-generating devices contain an interrupt-parent
property which has a phandle value that points to the device to which the
device’s interrupts are routed, typically an interrupt controller. If an
interrupt-generating device does not have an interrupt-parent property,
its interrupt parent is assumed to be its devicetree parent."
This clearly says that if the "interrupt-parent" property is absent, then
the immediate devicetree parent will be assumed as the interrupt parent.
But the immediate parents of these nodes are not interrupt controllers
themselves.
This may lead to failure while wiring the interrupt for these nodes by an
operating system. But a few operating systems like Linux, workaround this
issue by walking up the parent nodes until it finds the "interrupt-cells"
property. Then the node that has the "interrupt-cells" property will be
used as the interrupt parent.
But this workaround is not as per the DT spec and is not being implemented
by other operating systems such as OpenBSD.
Hence, fix this issue by adding the "interrupts-extended" property that
explicitly specifies the spmi_bus node as the interrupt parent. Note that
the "interrupts-extended" property is chosen over "interrupt-parent" as it
allows specifying both interrupt parent phandle and interrupt specifiers in
a single property.
Reported-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213090118.11527-1-manivannan.sadhasivam@linaro.org
More Qualcomm ARM64 DT updates for 6.3
The new Qualcomm QDU1000 and QRU1000 platforms, and the IDP device on
these are introduced. New support for a couple of USB modem sticks from
THWC are introduced, so is support for Xiaomi Mi Pad 5 Pro and the Pro
SKU of the Herobrine device.
The Core Bus Fabric (CBF) is introduced on MSM8996. Interconnect paths
for UFS are also described.
A few fixes related to the power-grid of herobrine, on SC7280, are
introduced.
QFPROM is introduced on IPQ8074 and Interconnect providers are added for
SDM670.
On SDM845 the duplicated wcd9340 audio coded description is moved from
devices to a common file, audio devices are added to the OnePlus 6 and
6T.
On SM6115 debug UART, SMP2P, watchdog nodes are introduced, and the
platform is switched to use #address/size-cells of 2, in line with most
other platforms.
Camera control interface and clock controllers are added for SM6350, and
the CCI interface is enabled on the Fairphone FP4.
On SM8350 the interconnect reference of SDHCI controller is corrected,
DSI1 PHY clocks are properly described as sources for the Display clock
controller and DSI1 is wired up to the display controller.
The firmware paths are corrected for the Sony Xperia Nagara platform.
The GPR bus, audio servic3es and LPASS pinctrl nodes are added for the
SM8550 platform. Additionally a few small typos/errors are corrected.
gpio-ranges are corrected across MSM8953, SM6115 and SC8280XP and a
range of DT validation issues are corrected.
* tag 'qcom-arm64-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (81 commits)
arm64: dts: qcom: sc7280: Power herobrine's 3.3 eDP/TS rail more properly
arm64: dts: qcom: pmk8550: fix PON compatible
arm64: dts: qcom: sm8550: fix DSI controller compatible
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on evoker
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on villager
arm64: dts: qcom: sc7280: Add 3ms ramp to herobrine's pp3300_left_in_mlb
arm64: dts: qcom: sc7280: On QCard, regulator L3C should be 1.8V
arm64: dts: qcom: sc8280xp: correct LPASS GPIO gpio-ranges
arm64: dts: qcom: msm8992-lg-bullhead: Enable regulators
arm64: dts: qcom: sm6115: correct TLMM gpio-ranges
arm64: dts: qcom: msm8953: correct TLMM gpio-ranges
arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM and MPSS memory regions
arm64: dts: qcom: sm8350-hdk: correct LT9611 pin function
arm64: dts: qcom: sm8350-hdk: align pin config node names with bindings
arm64: dts: qcom: sm6350: Use specific qmpphy compatible
arm64: dts: qcom: sm6115: Add smp2p nodes
arm64: dts: qcom: sm7225-fairphone-fp4: Enable CCI busses
arm64: dts: qcom: sm6350: Add CCI nodes
arm64: dts: qcom: sm6350: Add camera clock controller
dt-bindings: clock: add QCOM SM6350 camera clock bindings
...
Link: https://lore.kernel.org/r/20230210192908.2039976-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v6.3, part two
Several cleanups pointed out by `make dtbs_check`:
1. Align LED status node name with bindings.
2. Drop redundant properties.
3. Move i2c-gpio node out of soc to top-level, as soc node is expected
to have only MMIO nodes.
4. Correct SPI NOR flash compatible in SMDK5250 and SMDKv310.
5. Align GPIO property names in WM1811-family codec nodes with bindings.
6. Correct MAX98090 codec DAI cells in Snow.
* tag 'samsung-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: correct max98090 DAI argument in Snow
ARM: dts: s5pv210: add "gpios" suffix to wlf,ldo1ena on Aries
ARM: dts: exynos: add "gpios" suffix to wlf,ldo1ena on Arndale
ARM: dts: exynos: add "gpios" suffix to wlf,ldo1ena on Midas
ARM: dts: exynos: correct SPI nor compatible in SMDK5250
ARM: dts: exynos: correct SPI nor compatible in SMDKv310
ARM: dts: exynos: move I2C10 out of soc node on Arndale
ARM: dts: exynos: drop redundant address/size cells from I2C10 on Arndale
ARM: dts: exynos: drop default status from I2C10 on Arndale
ARM: dts: exynos: align status led name with bindings on Origen4210
Link: https://lore.kernel.org/r/20230211113103.58894-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AT91 device tree updates for 6.3 #2
It contains:
- cleanups arround flexcom nodes on SAM9X60 SoC as follows:
- preserve same ID for flexcoms and the embedded nodes (e.g. flx4
will embed uart4, spi4, i2c4 but not e.g. uart1, spi2, i2c3);
- SoC specific bindings were moved from board specific file to SoC
specific file
- DMA bindings for all flexcom nodes were added
- SoC file was filled with missing flexcom nodes
- new SAM9X60 Curiosity board that contains 1 uSDcard interface, 1 SDcard
interface, 1 USB device interface, 2 USB Type-A interfaces, 2 CAN
interfaces, 1 10/100 Ethernet interface, 1 LCD RGB666 interface,
1 Gb DDR2, 4 Gb NAND Flash, 2Kb EEPROM, leds, button, power
regulators, UART and JTAG connectors
* tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board
dt-bindings: arm: at91: Add info on sam9x60 curiosity
ARM: dts: at91: sam9x60: Add missing flexcom definitions
ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes
ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sam9x60: fix spi4 node
ARM: dts: at91: sam9x60: move flexcom definitions
ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions
Link: https://lore.kernel.org/r/20230209084930.289721-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the equivalent of commit f5b4811e87 ("arm64: dts: qcom:
sc7180: Add trogdor eDP/touchscreen regulator off-on-time") and commit
23ff866987 ("arm64: dts: qcom: sc7180: Start the trogdor
eDP/touchscreen regulator on"), but for herobrine instead of trogdor.
The motivations for herobrine are the same as for trogdor.
NOTES:
* Currently for herobrine all boards are eDP, not MIPI. If/when we
have herobrine derivatives that are MIPI they we can evaluate
whether the same off-on-delay makes sense for them. For trogdor we
didn't add the delay to MIPI panels because the problem was found
late and nobody had complained about it. For herobrine defaulting to
assuming the same 500ms makes sense and if we find we need to
optimize later we can.
* Currently there are no oddball herobrine boards like homestar where
the panel really likes to be power cycled. If we have an oddball
board it will need to split the eDP and touchscreen rail anyway
(like homestar did) and we'll have to delete the "regulator-boot-on"
from that board.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230207163550.1.I5ff72b7746d5fca8f10ea61351bde4150ed1a7f8@changeid
On older revisions of evoker, the touchscreen was either
non-functional or needed special hardware magic to get it talking
properly. It's been decided that the proper way going forward is to
use L3C to power some buffers on the QCard and then configure the
touchscreens for 1.8V. Let's do that.
Note that this is safe to do even on older revs even if it might not
make the touchscreen work there (because they didn't have a properly
stuffed QCard). As talked about in the patch ("arm64: dts: qcom:
sc7280: On QCard, regulator L3C should be 1.8V") the L3C regulator
didn't go anywhere at all on older revs.
This patch relies on the patch ("HID: i2c-hid: goodix: Add
mainboard-vddio-supply") in order to function properly. Without that
patch this one won't do any harm but it won't actually accomplish its
goal.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.7.I2d960ed7f2445db0cf3d227fde985fbd740f3c4d@changeid
On never revs of sc7280-herobrine-villager (rev2+) the L3C rail is
provided to the touchscreen as the IO voltage rail. Let's add it in
the device tree.
NOTE: Even though this is only really needed on rev2+ villagers (-rev0
had non-functioning touchscreen and -rev1 had some hacky hardware
magic), it doesn't actually hurt to do this for old villager revs. As
talked about in the patch ("arm64: dts: qcom: sc7280: On QCard,
regulator L3C should be 1.8V") the L3C regulator didn't go anywhere at
all on older revs. That means that turning it on for older revs
doesn't hurt other than drawing a tiny bit of extra power. Since -rev0
and -rev1 villagers will never make it to real customers and it's nice
not to have too many old device trees, the better tradeoff seems to be
to enable it everywhere.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.3.I740d409bc5bb69bf4a7b3c4568ea6e7a92f16ccd@changeid
The "pp3300_left_in_mlb" rail on herobrine eventually connects up to
"vreg_edp_3p3" on the qcard. On several herobrine designs this rail
has been measured to need more than 1ms to turn on.
While technically a herobrine derivative (defined as anyone including
the "herobrine.dtsi") could change the board to make the rail rise
faster or slower, the fact that two boards (evoker and villager) both
measured it as taking more than 1ms implies that it's probably going
to be the norm. Thus, let's add a "regulator-enable-ramp-delay"
straight into the herobrine.dtsi to handle this. If a particular
derivative board needs a faster or slower one then they can override
it, though that feels unlikely.
While we measured something a bit over 1ms, we'll choose 3ms to give
us a tiny bit of margin. This isn't a rail that turns off and on all
the time anyway and 3ms is nothing compared to the total amount of
time to power on a panel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.2.I13814cefc5ab3e0a39ebd09f052e3fd25d4e8f1d@changeid
On the first sc7280 QCards the L3C rail was never really used for
anything. Stuffing options on the QCard meant that the QCard itself
didn't use this rail for anything. This rail did get sent to the
mainboard, but no existing mainboards ever did anything with it other
that route it to a testpoint.
On later sc7280 QCards, the L3C rail was repurposed. Instead of being
a (nominally) 3.3V rail, it was decided to make it a 1.8V rail. It is
now provided to the display connector (which might route it to the
touchscreen) and also used to power some buffers relating to
touchscreen IO. This rail is getting the additional tag "ts_avccio",
though some places still refer to it as "vreg_l3c_3p0" despite the
fact that the name now specifies the wrong voltage.
Since it never hurts for this rail to be 1.8V (even on old QCards /
old boards), let's just change it to 1.8V across the board and add the
extra "ts_avccio" moniker as a label in the device tree.
Future patches will start using this rail in their touchscreens.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.1.I784f4b3d7e4a06edafff4a3129f52e749889bc05@changeid
