Since the current bootloader for Loongson-1 does not support FDT,
introduce CONFIG_BUILTIN_DTB_NAME to enable a built-in DTB.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree for Smartloong-1C board, supporting CPU, clock, INTC,
UART, Ethernet, GPIO, USB host, RTC, watchdog, DMA, and NAND.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a device tree for LS1B-DEMO board, supporting CPU, clock, INTC,
UART, Ethernet, GPIO, USB host, RTC, watchdog, DMA, NAND, and AC97.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: stp@e100bb0 (lantiq,gpio-stp-xway): $nodename:0: 'stp@e100bb0' does not match '^gpio@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
With the DT binding updated with 501be7cece ("dt-bindings:
memory-controller: Define fallback compatible") we need to define a
proper compatible string for the memory controller node(s).
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad937 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0 ("net: lantiq: configure the burst length in ethernet drivers")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Jakub Kicinski <kuba@kernel.org>
This platform uses the same GPIO controller as Nomadik. It however has
its own pinconf & pinmux controller. EyeQ5 is the first platform to use
gpio-nomadik independently from pinctrl-nomadik.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the SoC I2C controller nodes to the platform devicetree. Use a
default bus frequency of 400kHz. They are AMBA devices that are matched
on PeriphID.
Set transfer timeout to 10ms instead of Linux's default of 200ms.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Now that OF ahb support was added to the ath9k driver, we can use it to
enable and use the SoC wireless found in these chipsets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the MMC/SDHCI controller found in the eyeQ5 SoC. It is based on the
cadence sd4hc controller and support modes up to HS400 enhanced strobe.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the MMC/SDHCI controller found in the eyeQ6 SoC. It is based on the
cadence sd4hc controller and support modes up to HS400 enhanced strobe.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When starting up, the GARDENA smart Gateway's power LED should be
flashing green. It is unclear why it was initially set to "off".
The LED frequency cannot be configured in the devicetree. Luckily, the
default is 1 Hz, which is what we want.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Most notably, add the mediatek,sysctl phandle and remove the redundant
reset/interrupt-related properties from the watchdog node. This is in
line with the corresponding devicetree (mt7628an.dtsi) used by the
OpenWrt project.
This has been tested on the MT7688-based GARDENA smart Gateway.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add DTS files in support of EcoNet platform, including SmartFiber XP8421-B,
a low cost commercially available board based on EN751221.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current MT7628A device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current MT7620A device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current RT3883 device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current RT3050 device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Current RT2880 device tree file system controller node is wrong since it is
not matching bindings. Hence, update it to match current bindings updating
it also to use new introduced clock constants.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Define a gpio-restart node to the Cisco SG220-26P so the device can be
rebooted using the SoC's hard reset pin. Set the priority to 192 so the
gpio-restart method takes priority over the watchdog restart.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add some of the SoC's CPU peripherals currently supported:
- GPIO controller with support for 24 GPIO lines, although not all
lines are brought out to pads on the SoC package. These lines can
generate interrupts from external sources.
- Watchdog which can be used to restart the SoC if no external restart
logic is present.
- SPI controller, primarily used to access NOR flash
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a fixed clock to define the clock frequency of the Lexra bus and use
this for the two uart nodes instead of a separate clock-frequency
property.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The uart interrupts on RTL838x chips do not lead to the CPU's interrupt
controller directly, but passes via the SoC interrupt controller. Update
the interrupt-parent property to fix this.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the SoC interrupt controller so other components can link to it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
rtl83xx.dtsi was once (presumably) created as a base for both RTL838x
and RTL839x SoCs. Both SoCs have a different CPU and the peripherals
require different compatibles. Fold rtl83xx.dtsi into rtl838x.dtsi,
currently only supporting RTL838x SoCs, and create the RTL839x base
include later when required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Although not strictly required by the simple-bus binding, add the bus
offset to the node name to be consistent with other nodes. Also drop the
node label as it is not referenced anywhere.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The referenced CPU clock does not require any additional #clock-cells,
so drop the extraneous '0' in the referenced CPU clock.
The binding for MIPS cpus also does not allow for the clock-names
property, so just drop it.
This resolves some error message from 'dtbs_check':
cpu@0: clocks: [[4], [0]] is too long
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # For RTL9302C
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The RTL930x SoC series is sufficiently different to warrant its own base
dtsi. This ensures no properties need to be deleted or overwritten, and
prevents accidental inclusions of updates from rtl83xx.dtsi.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # For RTL9302C
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The CM3.5 device used in EyeQ6H SoCs incorrectly reports the status
for Hardware Cache Initialization (HCI). This commit adds the
compatible string for the CM to acknowledge this issue, which enables
the use of the second CPU cluster.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Replace the deprecated "simple-audio-card,hp-det-gpio" property by
"simple-audio-card,hp-det-gpios" in Simple Audio Card device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Pull Char/Misc/IIO driver updates from Greg KH:
"Here is the "big" set of char/misc/iio and other smaller driver
subsystem updates for 6.14-rc1. Loads of different things in here this
development cycle, highlights are:
- ntsync "driver" to handle Windows locking types enabling Wine to
work much better on many workloads (i.e. games). The driver
framework was in 6.13, but now it's enabled and fully working
properly. Should make many SteamOS users happy. Even comes with
tests!
- Large IIO driver updates and bugfixes
- FPGA driver updates
- Coresight driver updates
- MHI driver updates
- PPS driver updatesa
- const bin_attribute reworking for many drivers
- binder driver updates
- smaller driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
ntsync: Fix reference leaks in the remaining create ioctls.
spmi: hisi-spmi-controller: Drop duplicated OF node assignment in spmi_controller_probe()
spmi: Set fwnode for spmi devices
ntsync: fix a file reference leak in drivers/misc/ntsync.c
scripts/tags.sh: Don't tag usages of DECLARE_BITMAP
dt-bindings: interconnect: qcom,msm8998-bwmon: Add SM8750 CPU BWMONs
dt-bindings: interconnect: OSM L3: Document sm8650 OSM L3 compatible
dt-bindings: interconnect: qcom-bwmon: Document QCS615 bwmon compatibles
interconnect: sm8750: Add missing const to static qcom_icc_desc
memstick: core: fix kernel-doc notation
intel_th: core: fix kernel-doc warnings
binder: log transaction code on failure
iio: dac: ad3552r-hs: clear reset status flag
iio: dac: ad3552r-common: fix ad3541/2r ranges
iio: chemical: bme680: Fix uninitialized variable in __bme680_read_raw()
misc: fastrpc: Fix copy buffer page size
misc: fastrpc: Fix registered buffer page address
misc: fastrpc: Deregister device nodes properly in error scenarios
nvmem: core: improve range check for nvmem_cell_write()
nvmem: qcom-spmi-sdam: Set size in struct nvmem_config
...
Commit 654102df2a ("kbuild: add generic support for built-in boot
DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB and BUILTIN_DTB_ALL when the built-in DTB
support is enabled.
DTBs compiled under arch/mips/boot/dts/ will be wrapped by the generic
rule in scripts/Makefile.vmlinux.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
