Reorder lpi2c2, lpi2c3, mu1 and mu2 label in alphabetical order.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move node "rtc@53" to existed "&lpi2c3" and remove redundant
"&lpi2c3" label.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX fixes for 6.10:
- Fix GPIO number for reg_usdhc2_vmmc on imx8qm-mek board.
- Enable hysteresis for SODIMM_17 pin on imx8mm-verdin board to increase
immunity against noise.
- Remove 'no-sdio' property for uSDHC2 on imx93-11x11-evk board, so that
SDIO cards could also work.
- Fix BT shutdown GPIO for imx8mp-venice-gw73xx-2x board.
- Fix panel node deleting on imx53-qsb-hdmi, as /delete-node/ directive
doesn't really delete a node in a DT overlay.
- Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM.
- Fix GPU speed for imx8mm-verdin board by enabling overdrive mode in
the SOM dtsi.
The GW7400 has an onboard DP83867 RGMII GbE PHY:
- add RGMII delay and FIFO configuration
- add LED configuration required to use them via netdev trigger:
two LED's (LED1 and LED2, skipping LED0).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW702x SoM has an onboard DP83867 RGMII GbE PHY that drives two
LED's (LED1 and LED2, skipping LED0). Add the appropriate dt bindings to
allow these PHY LED's to be controlled via a netdev trigger.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW700x SoM has an onboard DP83867 RGMII GbE PHY that drives two
LED's (LED1 and LED2, skipping LED0). Add the appropriate dt bindings to
allow these PHY LED's to be controlled via a netdev trigger.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the dt-schema warnings due to #address-cells/#size-cells being
unnecessary when there are no children with reg cells.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pgc_mlmix shows a power-domain@24, but the reg value is
IMX8MP_POWER_DOMAIN_MLMIX which is set to 4.
The stuff after the @ symbol should match the stuff referenced
by 'reg' so reorder the pgc_mlmix so it to appear as power-domain@4.
Fixes: 834464c850 ("arm64: dts: imx8mp: add mlmix power domain")
Fixes: 4bedc468b7 ("arm64: dts: imx8mp: Add NPU Node")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the board device tree with sdhc1/2, cm33, mu, lpuart1, lpi2c1/2,
usb enabled and etc, which to support the i.MX 93 quick start evaluation
kit that provides a low-cost platform to evaluate the i.MX 93 applications
processors in a 9x9mm package.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a minimal dts for i.MX95 19x19 EVK board:
- lpuart1 as console
- sdhc1/2 as storage
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
and Edgelock secure enclave security. This patch is to add a minimal
dtsi, with cpu cores, scmi, gic, uart, mu, sdhc, lpi2c added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add thermal subfix for thermal node name to fix DTB_CHECK warning:
thermal-zones: '...' do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use common node name 'mmc' to fix DTB_CHECK warning.
Add compatible string 'fsl,ls2080a-esdhc' for fsl-lx2160a.
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: esdhc@1560000: $nodename:0: 'esdhc@1560000' does not match '^mmc(@.*)?$'
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: esdhc@1560000: $nodename:0: 'esdhc@1560000' does not match '^mmc(@.*)?$'
arch/arm64/boot/dts/freescale/fsl-ls1046a-frwy.dtb: esdhc@1560000: $nodename:0: 'esdhc@1560000' does not match '^mmc(@.*)?$'
arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dtb: esdhc@2140000: $nodename:0: 'esdhc@2140000' does not match '^mmc(@.*)?$'
arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dtb: esdhc@2140000: $nodename:0: 'esdhc@2140000' does not match '^mmc(@.*)?$'
arch/arm64/boot/dts/freescale/fsl-lx2160a-honeycomb.dtb: esdhc@2140000: compatible:0: 'fsl,esdhc' is not one of ['fsl,mpc8536-esdhc', 'fsl,mpc8378-esdhc', 'fsl,p2020-esdhc', 'fsl,p4080-esdhc', 'fsl,t1040-esdhc', 'fsl,t4240-esdhc', 'fsl,ls1012a-esdhc', 'fsl,ls1028a-esdhc', 'fsl,ls1088a-esdhc', 'fsl,ls1043a-esdhc', 'fsl,ls1046a-esdhc', 'fsl,ls2080a-esdhc']
from schema $id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml#
arch/arm64/boot/dts/freescale/fsl-lx2160a-honeycomb.dtb: esdhc@2140000: $nodename:0: 'esdhc@2140000' does not match '^mmc(@.*)?$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the HDMI output of the MSC SM2-MB-EP1 carrier board based the
SM2S-IMX8PLUS SMARC module.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace hard-coded interrupt parts (GIC, flags) with standard defines
for readability. No changes in resulting DTBs. The comment was saying
interrupt was active low, but the actual used value was active high, so
assume that the code, not the comment, is correct.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace hard-coded interrupt parts (GIC, flags) with standard defines
for readability. No changes in resulting DTBs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028ARDB board contains three EEPROM devices, for
storing boot code, DDR SPD and board information. Add the
missing entries to the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SODIMM 17 can be used as an edge triggered interrupt supplied from an
off board source.
Enable hysteresis on the pinmuxing to increase immunity against noise
on the signal.
Fixes: 60f01b5b5c ("arm64: dts: imx8mm-verdin: update iomux configuration")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The adv7535 has some unnecessary entries which can be removed since
they were not setup properly anyway and the defaults work just fine.
Removing them and adding some required regulators make the errors
detected from CHECK_DTBS go away:
reg-names:1: 'edid' was expected
reg-names:2: 'cec' was expected
'avdd-supply' is a required property
'dvdd-supply' is a required property
'pvdd-supply' is a required property
'a2vdd-supply' is a required property
'v3p3-supply' is a required property
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dt_binding require I2C's clock name is "ipg". Change it to "ipg" from "i2c"
to fix below DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dtb: i2c@2010000: clock-names:0: 'ipg' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dt_binding require I2C's clock name is "ipg". Change it to "ipg" from "i2c"
to fix below DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dtb: i2c@2000000: clock-names:0: 'ipg' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dt_binding require I2C's clock name is "ipg". Change it to "ipg" from "i2c"
to fix below DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: i2c@2190000: clock-names:0: 'ipg' was expecte
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change order of sai's dma-names to clearn up below DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: sai@2b50000: dma-names:1: 'tx' was expected
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: sai@2b60000: dma-names:1: 'tx' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Verdin I2C2 may be used to access other I2C devices apart from serving
as an HDMI DDC channel.
Thus do not limit the used I2C clock frequency to 10kHz in the module
specific device tree part.
If an overlay configures i2c2 as DDC the overlay is also responsible
to cope with an appropriate I2C clock.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Verdin I2C2 may be used to access other I2C devices apart from serving
as an HDMI DDC channel.
Thus do not limit the used I2C clock frequency to 10kHz in the module
specific device tree part.
If an overlay configures i2c2 as DDC the overlay is also responsible
to cope with an appropriate I2C clock.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UART2 and UART4 can used in following combination,
2 x RS232:
- UART2 and UART4 without flow control
- MUX selection GPIO3_20 must be held low
1 x RS232 + 1 x RS485:
- UART2 - RS232
- UART4 - RS485
- MUX selection GPIO3_20 must be held high
- RE/DE for RS485 controlled with GPIO3_25
1 x RS232 with flow control:
- UART2 - RS232
- MUX selection GPIO3_20 must be held low
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I210 intel ethernet controller is connected to PCIe. Enable the PHY
to use the ethernet controller.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reorder the SAI dma-names to ensure "rx" precedes "tx" as required to fixes
the DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: audio-controller@f100000: dma-names:1: 'tx' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,sai.yaml#
arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: audio-controller@f110000: dma-names:1: 'tx' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the undocumented compatible string 'fsl,ls-pcie-ep' property from
the ls1028a device tree source to fix DTB_CHECK warnings.
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: pcie-ep@3400000: compatible: ['fsl,ls1028a-pcie-ep', 'fsl,ls-pcie-ep'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The only key that should wake up the phone is power button press. This
prevents accidental wakeup due to e.g. pressing the buttons in the
pocket or backpack and is in line what userspace uses to unblank the
device.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We cannot use /delete-node/ directive to delete a node in a DT
overlay. The node won't be deleted effectively. Instead, set
the node's status property to "disabled" to achieve something
similar.
Fixes: eeb403df95 ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable HDMI output on i.MX8MP DHCOM PDK2 and PDK3. The I2C5 on PDK2 and
I2C mux port 1 on PDK3 respectively are used in regular I2C mode instead
of HDMI DDC mode to permit connection of other I2C devices on those buses.
The pinctrl_hdmi node is part of the SoM DTSI already.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IMX8MP_CLK_CLKOUT2 supplies the TC9595 bridge with 13 MHz reference
clock. The IMX8MP_CLK_CLKOUT2 is supplied from IMX8MP_AUDIO_PLL2_OUT.
The IMX8MP_CLK_CLKOUT2 operates only as a power-of-two divider, and the
current 156 MHz is not power-of-two divisible to achieve 13 MHz.
To achieve 13 MHz output from IMX8MP_CLK_CLKOUT2, set IMX8MP_AUDIO_PLL2_OUT
to 208 MHz, because 208 MHz / 16 = 13 MHz.
Fixes: 20d0b83e71 ("arm64: dts: imx8mp: Add TC9595 bridge on DH electronics i.MX8M Plus DHCOM")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initialize audio PLL1 as the parent clock for 8kHz series rates,
audio PLL2 as the parent clock for 11kHz series rates. that PLL1
and PLL2 can together support full range of audio sample rates.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MX8-DLVDS-LCD1 display module integrates a KOE TX26D202VM0BWA LCD panel
and a touch IC. Add an overlay to support the LCD panel on i.MX8MP EVK.
Specify 148.5MHz clock frequency in panel-timing node to accommodate
3.5-fold 519.75MHz media_ldb clock which is derived from 1.0395GHz
video_pll1 clock.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
