When we are dynamically adding new ODM slices, we didn't update
blank state, if the pipe used by new ODM slice is previously blanked,
we will continue outputting blank pixel data on that slice causing
right half of the screen showing blank image.
The previous fix was a temporary hack to directly update current state
when committing new state. This could potentially cause hw and sw
state synchronization issues and it is not permitted by dc commit
design.
Cc: stable@vger.kernel.org
Fixes: 7fbf451e76 ("drm/amd/display: Reinit DPG when exiting dynamic ODM")
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A benchmark stress test (12-40 machines x 48hours) found that DCN315 has
cases where DC writes to an indirect register to set the smu clock msg
id, but when we go to read the same indirect register the returned msg
id doesn't match with what we just set it to. So, to fix this retry the
write until the register's value matches with the requested value.
Cc: stable@vger.kernel.org # 6.1+
Fixes: f949039961 ("drm/amd/display: Add DCN315 CLK_MGR")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Fudong Wang <fudong.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This partially reverts commit 460ea89805 ("drm/amd/display: update add
plane to context logic with a new algorithm").
The new secondary pipe allocation logic triggers an issue with a
specific hardware state transition and causes a frame of corruption when
toggling between windowed MPO and ODM desktop only mode. Ideally hwss is
supposed to handle this scenario. We are temporarily reverting the logic
and investigate the root cause why this transition would cause
corruptions.
Fixes: 460ea89805 ("drm/amd/display: update add plane to context logic with a new algorithm")
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fbcon requires that we implement &drm_framebuffer_funcs.dirty.
Otherwise, the framebuffer might take a while to flush (which would
manifest as noticeable lag). However, we can't enable this callback for
non-fbcon cases since it may cause too many atomic commits to be made at
once. So, implement amdgpu_dirtyfb() and only enable it for fbcon
framebuffers (we can use the "struct drm_file file" parameter in the
callback to check for this since it is only NULL when called by fbcon,
at least in the mainline kernel) on devices that support atomic KMS.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org # 6.1+
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2519
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_device_mode1_reset will return gpu mode1_reset
succeed (ret = 0) as long as wait_for_bootloader call
succeed, regardless of the status reported by smu or
psp firmware. This results to driver continue executing
recovery even smu or psp fail to perform mode1 reset.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
OTG_STATIC_SCREEN_EVENT_MASK is changed in DCN3,
but we still follow DCN2 to apply setting for
OTG_STATIC_SCREEN_EVENT_MASK.
[How]
Add new function to apply correct settings for DCN3 series.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: SungHuai Wang <danny.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As made mention of in commit 4a2df0d1f2 ("drm/amd/display: Fixed
non-native modes not lighting up"), we shouldn't call
drm_mode_set_crtcinfo() once the crtc timings have been decided. Since,
it can cause settings to be unintentionally overwritten. So, since
dm_state is never NULL now, we can use old_stream to determine if we
should call drm_mode_set_crtcinfo() because we only need to set the crtc
timing parameters for entirely new streams.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Fixes: bd49f19039 ("drm/amd/display: Always set crtcinfo from create_stream_for_sink")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
Current SRIOV still using adev->clock.default_XX which gets from
atomfirmware. But these fields are abandoned in atomfirmware long ago.
Which may cause function to return a 0 value.
[How]
We don't need to check whether SR-IOV. For SR-IOV one-vf-mode,
pm is enabled and VF is able to read dpm clock
from pmfw, so we can use dpm clock interface directly. For
multi-VF mode, VF pm is disabled, so driver can just react as pm
disabled. One-vf-mode is introduced from GFX9 so it shall not have
any backward compatibility issue.
Signed-off-by: Horace Chen <horace.chen@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If VBlank_nom is too small, it will cause
VStartUP_Start smaller than VBackPorch + VSync width which is an
invalid case for VStartUP_Start and where to send AS-SDP.
[How]
Setup a minimum value to VBlank_nom
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
vstartup is calculated to be a large number. it works because
it is within vertical blank, but it reduces region of blank that
can be used for power gating.
[how]
Calculation needs to convert micro seconds to number of
vertical lines.
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This Unit correction exposes a Replay corruption.
[how]
This reverts commit:
commit dbd29029c7 ("drm/amd/display: Correct unit conversion for vstartup")
Roll back unit conversion until Replay can fix their corruption.
Fixes: dbd29029c7 ("drm/amd/display: Correct unit conversion for vstartup")
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
if hmm_range_get_pages returns EBUSY error during
svm_range_validate_and_map, within the context of a page fault
interrupt. This should retry through svm_range_restore_pages
callback. Therefore we treat this as EAGAIN error instead, and defer
it to restore pages fallback.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add critical temperature message support func for smu v13.0.6
and expose critical temperature as part of hw mon attributes
for GC v9.4.3
v2:
Added comment for pmfw version requirement & move the check
to get_thermal_temperature_range function
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
7957ec80ef ("drm/amdgpu: Add FRU sysfs nodes only if needed") moved
the documentation for some of the sysfs nodes to amdgpu_fru_eeprom.c.
Update the documentation accordingly.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- There is a DPM issue where if DC is not present,
FCLK will stay at low level.
We need to send a SMU message to configure the DPM
- Reuse smu_v13_0_notify_display_change() for this purpose
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bokun Zhang <bokun.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Setup replay config on device init.
- Enable replay if feature is enabled (prioritize replay over PSR, since
it can be enabled in more usecases)
- Add debug masks to enable replay on supported ASICs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, NO_PREFETCH is passed implicitly through
drm_nouveau_gem_pushbuf_push::length and drm_nouveau_exec_push::va_len.
Since this is a direct representation of how the HW is programmed it
isn't really future proof for a uAPI. Hence, fix this up for the new
uAPI and split up the va_len field of struct drm_nouveau_exec_push,
such that we keep 32bit for va_len and 32bit for flags.
For drm_nouveau_gem_pushbuf_push::length at least provide
NOUVEAU_GEM_PUSHBUF_NO_PREFETCH to indicate the bit shift.
While at it, fix up nv50_dma_push() as well, such that the caller
doesn't need to encode the NO_PREFETCH flag into the length parameter.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230823181746.3446-1-dakr@redhat.com
If a sched job depends on a dma-fence from a job from the same GPU
scheduler instance, but a different scheduler entity, the GPU scheduler
does only wait for the particular job to be scheduled, rather than for
the job to fully complete. This is due to the GPU scheduler assuming
that there is a scheduler instance per ring. However, the current
implementation, in order to avoid arbitrary amounts of kthreads, has a
single scheduler instance while scheduler entities represent rings.
As a workaround, set the DRM_SCHED_FENCE_DONT_PIPELINE for all
out-fences in order to force the scheduler to wait for full job
completion for dependent jobs from different entities and same scheduler
instance.
There is some work in progress [1] to address the issues of firmware
schedulers; once it is in-tree the scheduler topology in Nouveau should
be re-worked accordingly.
[1] https://lore.kernel.org/dri-devel/20230801205103.627779-1-matthew.brost@intel.com/
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collaboralcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20230811010632.2473-1-dakr@redhat.com
Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.
Core:
- SM6125 MDSS support
DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup
DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support
DSI PHY:
- SM6125 support in 14nm DSI PHY driver
GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
linux-firmware and we see no evidence that it should be different
from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com
After the commit in the Fixes: line below, HPD polling stopped working
on i915, since after that change calling drm_kms_helper_poll_enable()
doesn't restart drm_mode_config::output_poll_work if the work was
stopped (no connectors needing polling) and enabling polling for a
connector (during runtime suspend or detecting an HPD IRQ storm).
After the above change calling drm_kms_helper_poll_enable() is a nop
after it's been called already and polling for some connectors was
disabled/re-enabled.
Fix this by calling drm_kms_helper_poll_reschedule() added in the
previous patch instead, which reschedules the work whenever expected.
Fixes: d33a54e399 ("drm/probe_helper: sort out poll_running vs poll_enabled")
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-2-imre.deak@intel.com
(cherry picked from commit 50452f2f76)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial core fixes for 6.5-rc7 that resolve
a lot of reported issues.
Primarily in here are the fixes for the serial bus code from Tony that
came in -rc1, as it hit wider testing with the huge number of
different types of systems and serial ports. All of the reported
issues with duplicate names and other issues with this code are now
resolved.
Other than that included in here is:
- n_gsm fix for a previous fix
- 8250 lockdep annotation fix
- fsl_lpuart serial driver fix
- TIOCSTI documentation update for previous CAP_SYS_ADMIN change
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: core: Fix serial core port id, including multiport devices
serial: 8250: drop lockdep annotation from serial8250_clear_IER()
tty: n_gsm: fix the UAF caused by race condition in gsm_cleanup_mux
serial: core: Revert port_id use
TIOCSTI: Document CAP_SYS_ADMIN behaviour in Kconfig
serial: 8250: Fix oops for port->pm on uart_change_pm()
serial: 8250: Reinit port_id when adding back serial8250_isa_devs
serial: core: Fix kmemleak issue for serial core device remove
MAINTAINERS: Merge TTY layer and serial drivers
serial: core: Fix serial_base_match() after fixing controller port name
serial: core: Fix serial core controller port name to show controller id
serial: core: Fix serial core port id to not use port->line
serial: core: Controller id cannot be negative
tty: serial: fsl_lpuart: Clear the error flags by writing 1 for lpuart32 platforms
Pull rust fix from Miguel Ojeda:
- Macros: fix 'HAS_*' redefinition by the '#[vtable]' macro
under conditional compilation
* tag 'rust-fixes-6.5-rc7' of https://github.com/Rust-for-Linux/linux:
rust: macros: vtable: fix `HAS_*` redefinition (`gen_const_name`)
Pull i2c fixes from Wolfram Sang:
"Usual set of driver fixes. A bit more than usual because I was
unavailable for a while"
* tag 'i2c-for-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm-iproc: Fix bcm_iproc_i2c_isr deadlock issue
i2c: Update documentation to use .probe() again
i2c: sun6i-p2wi: Fix an error message in probe()
i2c: hisi: Only handle the interrupt of the driver's transfer
i2c: tegra: Fix i2c-tegra DMA config option processing
i2c: tegra: Fix failure during probe deferral cleanup
i2c: designware: Handle invalid SMBus block data response length value
i2c: designware: Correct length byte validation logic
i2c: imx-lpi2c: return -EINVAL when i2c peripheral clk doesn't work
