When ngbe_sw_init() is called, memory is allocated for wx->rss_key
in wx_init_rss_key(). However, in ngbe_probe() function, the subsequent
error paths after ngbe_sw_init() don't free the rss_key. Fix that by
freeing it in error path along with wx->mac_table.
Also change the label to which execution jumps when ngbe_sw_init()
fails, because otherwise, it could lead to a double free for rss_key,
when the mac_table allocation fails in wx_sw_init().
Fixes: 02338c484a ("net: ngbe: Initialize sw info and register netdev")
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250412154927.25908-1-abdun.nihaal@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
igc: Fix PTM timeout
Christopher S M Hall says:
There have been sporadic reports of PTM timeouts using i225/i226 devices
These timeouts have been root caused to:
1) Manipulating the PTM status register while PTM is enabled
and triggered
2) The hardware retrying too quickly when an inappropriate response
is received from the upstream device
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
The first patch in this series also resolves an issue reported by Corinna
Vinschen relating to kdump:
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not zero, but extremly reduced.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: add lock preventing multiple simultaneous PTM transactions
igc: cleanup PTP module if probe fails
igc: handle the IGC_PTP_ENABLED flag correctly
igc: move ktime snapshot into PTM retry loop
igc: increase wait time before retrying PTM
igc: fix PTM cycle trigger logic
====================
Link: https://patch.msgid.link/20250411162857.2754883-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We started generating C code for OvS a while back, but actually
C codegen only supports fixed headers specified at the family
level right now (schema also allows specifying them per op).
ovs_flow and ovs_datapath already specify the fixed header
at the family level but ovs_vport does it per op.
Move the property, all ops use the same header.
This ensures YNL C sees the correct hdr_len:
const struct ynl_family ynl_ovs_vport_family = {
.name = "ovs_vport",
- .hdr_len = sizeof(struct genlmsghdr),
+ .hdr_len = sizeof(struct genlmsghdr) + sizeof(struct ovs_header),
};
Fixes: 7c59c9c8f2 ("tools: ynl: generate code for ovs families")
Link: https://patch.msgid.link/20250409145541.580674-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lockdep found the following dependency:
&dev_instance_lock_key#3 -->
&rdev->wiphy.mtx -->
&net->xdp.lock -->
&xs->mutex -->
&dev_instance_lock_key#3
The first dependency is the problem. wiphy mutex should be outside
the instance locks. The problem happens in notifiers (as always)
for CLOSE. We only hold the instance lock for ops locked devices
during CLOSE, and WiFi netdevs are not ops locked. Unfortunately,
when we dev_close_many() during netns dismantle we may be holding
the instance lock of _another_ netdev when issuing a CLOSE for
a WiFi device.
Lockdep's "Possible unsafe locking scenario" only prints 3 locks
and we have 4, plus I think we'd need 3 CPUs, like this:
CPU0 CPU1 CPU2
---- ---- ----
lock(&xs->mutex);
lock(&dev_instance_lock_key#3);
lock(&rdev->wiphy.mtx);
lock(&net->xdp.lock);
lock(&xs->mutex);
lock(&rdev->wiphy.mtx);
lock(&dev_instance_lock_key#3);
Tho, I don't think that's possible as CPU1 and CPU2 would
be under rtnl_lock. Even if we have per-netns rtnl_lock and
wiphy can span network namespaces - CPU0 and CPU1 must be
in the same netns to see dev_instance_lock, so CPU0 can't
be installing a socket as CPU1 is tearing the netns down.
Regardless, our expected lock ordering is that wiphy lock
is taken before instance locks, so let's fix this.
Go over the ops locked and non-locked devices separately.
Note that calling dev_close_many() on an empty list is perfectly
fine. All processing (including RCU syncs) are conditional
on the list not being empty, already.
Fixes: 7e4d784f58 ("net: hold netdev instance lock during rtnetlink operations")
Reported-by: syzbot+6f588c78bf765b62b450@syzkaller.appspotmail.com
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250412233011.309762-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After detecting the np_link_fail exception,
the driver attempts to fix the exception by
using phy_stop() and phy_start() in the scheduled task.
However, hbg_fix_np_link_fail() and .ndo_stop()
may be concurrently executed. As a result,
phy_stop() is executed twice, and the following Calltrace occurs:
hibmcge 0000:84:00.2 enp132s0f2: Link is Down
hibmcge 0000:84:00.2: failed to link between MAC and PHY, try to fix...
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 71 PID: 23391 at drivers/net/phy/phy.c:1503 phy_stop...
...
pc : phy_stop+0x138/0x180
lr : phy_stop+0x138/0x180
sp : ffff8000c76bbd40
x29: ffff8000c76bbd40 x28: 0000000000000000 x27: 0000000000000000
x26: ffff2020047358c0 x25: ffff202004735940 x24: ffff20200000e405
x23: ffff2020060e5178 x22: ffff2020060e4000 x21: ffff2020060e49c0
x20: ffff2020060e5170 x19: ffff20202538e000 x18: 0000000000000020
x17: 0000000000000000 x16: ffffcede02e28f40 x15: ffffffffffffffff
x14: 0000000000000000 x13: 205d313933333254 x12: 5b5d393430303233
x11: ffffcede04555958 x10: ffffcede04495918 x9 : ffffcede0274fee0
x8 : 00000000000bffe8 x7 : c0000000ffff7fff x6 : 0000000000000001
x5 : 00000000002bffa8 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff20202e429480
Call trace:
phy_stop+0x138/0x180
hbg_fix_np_link_fail+0x4c/0x90 [hibmcge]
hbg_service_task+0xfc/0x148 [hibmcge]
process_one_work+0x180/0x398
worker_thread+0x210/0x328
kthread+0xe0/0xf0
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
This patch adds the rtnl_lock to hbg_fix_np_link_fail()
to ensure that other operations are not performed concurrently.
In addition, np_link_fail exception can be fixed
only when the PHY is link.
Fixes: e0306637e8 ("net: hibmcge: Add support for mac link exception handling feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250410021327.590362-8-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MAC hardware supports receiving two types of
pause frames from link partner.
One is a pause frame with a destination address
of 01:80:C2:00:00:01.
The other is a pause frame whose destination address
is the address of the hibmcge driver.
01:80:C2:00:00:01 is supported by default.
In .ndo_set_mac_address(), the hibmcge driver calls
.hbg_hw_set_rx_pause_mac_addr() to set its mac address as the
destination address of the rx puase frame.
Therefore, pause frames with two types of MAC addresses can be received.
Currently, the rx pause addr does not restored after reset.
As a result, pause frames whose destination address is
the hibmcge driver address cannot be correctly received.
This patch restores the configuration by calling
.hbg_hw_set_rx_pause_mac_addr() after reset is complete.
Fixes: 3f5a61f6d5 ("net: hibmcge: Add reset supported in this module")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250410021327.590362-7-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the debugfs file, the driver displays the np_link fail state
based on the HBG_NIC_STATE_NP_LINK_FAIL.
However, HBG_NIC_STATE_NP_LINK_FAIL is cleared in hbg_service_task()
So, this value of np_link fail is always false.
This patch directly reads the related register to display the real state.
Fixes: e0306637e8 ("net: hibmcge: Add support for mac link exception handling feature")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250410021327.590362-6-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A dbg log is generated when the driver modifies the MTU,
which is expected to trace the change of the MTU.
However, the log is recorded after WRITE_ONCE().
At this time, netdev->mtu has been changed to the new value.
As a result, netdev->mtu is the same as new_mtu.
This patch modifies the log location and records logs before WRITE_ONCE().
Fixes: ff4edac6e9 ("net: hibmcge: Implement some .ndo functions")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250410021327.590362-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
hbg_irqs is a global array which contains irq statistics.
However, the irq statistics of different network ports
point to the same global array. As a result, the statistics are incorrect.
This patch allocates a statistics array for each network port
to prevent the statistics of different network ports
from affecting each other.
irq statistics are removed from hbg_irq_info. Therefore,
all data in hbg_irq_info remains unchanged. Therefore,
the input parameter of some functions is changed to const.
Fixes: 4d089035fa ("net: hibmcge: Add interrupt supported in this module")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250410021327.590362-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver supports pause frames,
but does not pass pause frames based on rx pause enable configuration,
resulting in incorrect pause frame statistics.
like this:
mz eno3 '01 80 c2 00 00 01 00 18 2d 04 00 9c 88 08 00 01 ff ff' \
-p 64 -c 100
ethtool -S enp132s0f2 | grep -v ": 0"
NIC statistics:
rx_octets_total_filt_cnt: 6800
rx_filt_pkt_cnt: 100
The rx pause frames are filtered by the MAC hardware.
This patch configures pass pause frames based on the
rx puase enable status to ensure that
rx pause frames are not filtered.
mz eno3 '01 80 c2 00 00 01 00 18 2d 04 00 9c 88 08 00 01 ff ff' \
-p 64 -c 100
ethtool --include-statistics -a enp132s0f2
Pause parameters for enp132s0f2:
Autonegotiate: on
RX: on
TX: on
RX negotiated: on
TX negotiated: on
Statistics:
tx_pause_frames: 0
rx_pause_frames: 100
Fixes: 3a03763f38 ("net: hibmcge: Add pauseparam supported in this module")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250410021327.590362-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot reports a case of ethtool_ops->get_link being called without
ops lock:
ethtool_op_get_link+0x15/0x60 net/ethtool/ioctl.c:63
bond_check_dev_link+0x1fb/0x4b0 drivers/net/bonding/bond_main.c:864
bond_miimon_inspect drivers/net/bonding/bond_main.c:2734 [inline]
bond_mii_monitor+0x49d/0x3170 drivers/net/bonding/bond_main.c:2956
process_one_work kernel/workqueue.c:3238 [inline]
process_scheduled_works+0xac3/0x18e0 kernel/workqueue.c:3319
worker_thread+0x870/0xd50 kernel/workqueue.c:3400
kthread+0x7b7/0x940 kernel/kthread.c:464
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:153
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
Commit 04efcee6ef ("net: hold instance lock during NETDEV_CHANGE")
changed to lockless __linkwatch_sync_dev in ethtool_op_get_link.
All paths except bonding are coming via locked ioctl. Add necessary
locking to bonding.
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reported-by: syzbot+48c14f61594bdfadb086@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=48c14f61594bdfadb086
Fixes: 04efcee6ef ("net: hold instance lock during NETDEV_CHANGE")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250410161117.3519250-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Just a handful of fixes, notably
- iwlwifi: various build warning fixes (e.g. PM_SLEEP)
- iwlwifi: fix operation when FW reset handshake times out
- mac80211: drop pending frames on interface down
* tag 'wireless-2025-04-11' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
Revert "wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()"
wifi: iwlwifi: mld: Restart firmware on iwl_mld_no_wowlan_resume() error
wifi: iwlwifi: pcie: set state to no-FW before reset handshake
wifi: wl1251: fix memory leak in wl1251_tx_work
wifi: brcmfmac: fix memory leak in brcmf_get_module_param
wifi: iwlwifi: mld: silence uninitialized variable warning
wifi: mac80211: Purge vif txq in ieee80211_do_stop()
wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()
wifi: at76c50x: fix use after free access in at76_disconnect
wifi: add wireless list to MAINTAINERS
iwlwifi: mld: fix building with CONFIG_PM_SLEEP disabled
wifi: iwlwifi: mld: fix PM_SLEEP -Wundef warning
wifi: iwlwifi: mld: reduce scope for uninitialized variable
====================
Link: https://patch.msgid.link/20250411142354.24419-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a mutex around the PTM transaction to prevent multiple transactors
Multiple processes try to initiate a PTM transaction, one or all may
fail. This can be reproduced by running two instances of the
following:
$ sudo phc2sys -O 0 -i tsn0 -m
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
Note: Normally two instance of PHC2SYS will not run, but one process
should not break another.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225/i226 hardware retries if it receives an inappropriate response
from the upstream device. If the device retries too quickly, the root
port does not respond.
The wait between attempts was reduced from 10us to 1us in commit
6b8aa753a9 ("igc: Decrease PTM short interval from 10 us to 1 us"), which
said:
With the 10us interval, we were seeing PTM transactions take around
12us. Hardware team suggested this interval could be lowered to 1us
which was confirmed with PCIe sniffer. With the 1us interval, PTM
dialogs took around 2us.
While a 1us short cycle time was thought to be theoretically sufficient, it
turns out in practice it is not quite long enough. It is unclear if the
problem is in the root port or an issue in i225/i226.
Increase the wait from 1us to 4us. Increasing to 2us appeared to work in
practice on the setups we have available. A value of 4us was chosen due to
the limited hardware available for testing, with a goal of ensuring we wait
long enough without overly penalizing the response time when unnecessary.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
Fixes: 6b8aa753a9 ("igc: Decrease PTM short interval from 10 us to 1 us")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Writing to clear the PTM status 'valid' bit while the PTM cycle is
triggered results in unreliable PTM operation. To fix this, clear the
PTM 'trigger' and status after each PTM transaction.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not 0, but extremely reduced.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The reset handshake attempts to kill the firmware, and it'll go
into a pretty much dead state once we do that. However, if it
times out, then we'll attempt to dump the firmware to be able
to see why it didn't respond. During this dump, we cannot treat
it as if it was still running, since we just tried to kill it,
otherwise dumping will attempt to send a DBGC stop command. As
this command will time out, we'll go into a reset loop.
For now, fix this by setting the trans->state to say firmware
isn't running before doing the reset handshake. In the longer
term, we should clean up the way this state is handled.
It's not entirely clear but it seems likely that this issue was
introduced by my rework of the error handling, prior to that it
would've been synchronous at that point and (I think) not have
attempted to reset since it was already doing down.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219967
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219968
Fixes: 7391b2a4f7 ("wifi: iwlwifi: rework firmware error handling")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250411104054.63aa4f56894d.Ife70cfe997db03f0d07fdef2b164695739a05a63@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 5eb902b8e7 ("net/ipv6: Remove expired routes with a separated list
of routes.") introduced a separated list for managing route expiration via
the GC timer.
However, it missed adding exception routes (created by ip6_rt_update_pmtu()
and rt6_do_redirect()) to this GC list. As a result, these exceptions were
never considered for expiration and removal, leading to stale entries
persisting in the routing table.
This patch fixes the issue by calling fib6_add_gc_list() in
rt6_insert_exception(), ensuring that exception routes are properly tracked
and garbage collected when expired.
Fixes: 5eb902b8e7 ("net/ipv6: Remove expired routes with a separated list of routes.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/837e7506ffb63f47faa2b05d9b85481aad28e1a4.1744134377.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For bnxt when the agg ring is used then tcp-data-split is automatically
reported to be enabled, but __net_mp_open_rxq() requires tcp-data-split
to be explicitly enabled by the user.
Enable tcp-data-split explicitly in io_uring zc rx selftest.
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250409163153.2747918-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This prints an error message if the FW Dump trigger command fails. This
scenario is mainly observed in legacy chipsets 8987 and 8997 and also
IW416, where this feature is unavailable due to memory constraints.
Fixes: 998e447f44 ("Bluetooth: btnxpuart: Add support for HCI coredump feature")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts the change baudrate logic in nxp_shutdown.
Earlier, when the driver was removed, it restored the controller
baudrate to fw_init_baudrate, so that on re-loading the driver, things
work fine.
However, if the driver was removed while hci0 interface is down, the
change baudrate vendor command could not be sent by the driver. When the
driver was re-loaded, host and controller baudrate would be mismatched
and hci initialization would fail. The only way to recover would be to
reboot the system.
This issue was fixed by moving the restore baudrate logic from
nxp_serdev_remove() to nxp_shutdown().
This fix however caused another issue with the command "hciconfig hci0
reset", which makes hci0 DOWN and UP immediately.
Running "bluetoothctl power off" and "bluetoothctl power on" in a tight
loop works fine.
To maintain support for "hciconfig reset" command, the above mentioned fix
is reverted.
Fixes: 6fca6781d1 ("Bluetooth: btnxpuart: Move vendor specific initialization to .post_init")
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Documentation/networking/timestamping.rst implies TX timestamping OPT_ID
tskey increments for each sendmsg. In practice: TCP socket increments
it for all sendmsg, timestamping on or off, but UDP only when
timestamping is on. The user-visible counter resets when OPT_ID is
turned on, so difference can be seen only if timestamping is enabled for
some packets only (eg. via SO_TIMESTAMPING CMSG).
Fix BT sockets to work in the same way: stream sockets increment tskey
for all sendmsg (seqpacket already increment for timestamped only).
Fixes: 134f4b39df ("Bluetooth: add support for skb TX SND/COMPLETION timestamping")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The btrtl_initialize() function checks that rtl_load_file() either
had an error or it loaded a zero length file. However, if it loaded
a zero length file then the error code is not set correctly. It
results in an error pointer vs NULL bug, followed by a NULL pointer
dereference. This was detected by Smatch:
drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'
Fixes: 26503ad25d ("Bluetooth: btrtl: split the device initialization into smaller parts")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes sending MGMT_EV_DEVICE_FOUND for invalid address
(00:00:00:00:00:00) which is a regression introduced by
a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
since in the attempt to skip storing data for extended advertisement it
actually made the code to skip the entire if statement supposed to send
MGMT_EV_DEVICE_FOUND without attempting to use the last_addr_adv which
is garanteed to be invalid for extended advertisement since we never
store anything on it.
Link: https://github.com/bluez/bluez/issues/1157
Link: https://github.com/bluez/bluez/issues/1149#issuecomment-2767215658
Fixes: a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter.
Current release - regressions:
- core: hold instance lock during NETDEV_CHANGE
- rtnetlink: fix bad unlock balance in do_setlink()
- ipv6:
- fix null-ptr-deref in addrconf_add_ifaddr()
- align behavior across nexthops during path selection
Previous releases - regressions:
- sctp: prevent transport UaF in sendmsg
- mptcp: only inc MPJoinAckHMacFailure for HMAC failures
Previous releases - always broken:
- sched:
- make ->qlen_notify() idempotent
- ensure sufficient space when sending filter netlink notifications
- sch_sfq: really don't allow 1 packet limit
- netfilter: fix incorrect avx2 match of 5th field octet
- tls: explicitly disallow disconnect
- eth: octeontx2-pf: fix VF root node parent queue priority"
* tag 'net-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (38 commits)
ethtool: cmis_cdb: Fix incorrect read / write length extension
selftests: netfilter: add test case for recent mismatch bug
nft_set_pipapo: fix incorrect avx2 match of 5th field octet
net: ppp: Add bound checking for skb data on ppp_sync_txmung
net: Fix null-ptr-deref by sock_lock_init_class_and_name() and rmmod.
ipv6: Align behavior across nexthops during path selection
net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY
net: phy: move phy_link_change() prior to mdio_bus_phy_may_suspend()
selftests/tc-testing: sfq: check that a derived limit of 1 is rejected
net_sched: sch_sfq: move the limit validation
net_sched: sch_sfq: use a temporary work area for validating configuration
net: libwx: handle page_pool_dev_alloc_pages error
selftests: mptcp: validate MPJoin HMacFailure counters
mptcp: only inc MPJoinAckHMacFailure for HMAC failures
rtnetlink: Fix bad unlock balance in do_setlink().
net: ethtool: Don't call .cleanup_data when prepare_data fails
tc: Ensure we have enough buffer space when sending filter netlink notifications
net: libwx: Fix the wrong Rx descriptor field
octeontx2-pf: qos: fix VF root node parent queue index
selftests: tls: check that disconnect does nothing
...
Pull xen fixes from Juergen Gross:
- A simple fix adding the module description of the Xenbus frontend
module
- A fix correcting the xen-acpi-processor Kconfig dependency for PVH
Dom0 support
- A fix for the Xen balloon driver when running as Xen Dom0 in PVH mode
- A fix for PVH Dom0 in order to avoid problems with CPU idle and
frequency drivers conflicting with Xen
* tag 'for-linus-6.15a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: disable CPU idle and frequency drivers for PVH dom0
x86/xen: fix balloon target initialization for PVH dom0
xen: Change xen-acpi-processor dom0 dependency
xenbus: add module description
Pull block fixes from Jens Axboe:
- Add a missing ublk selftest script, from test additions added last
week
- Two fixes for ublk error recovery and reissue
- Cleanup of ublk argument passing
* tag 'block-6.15-20250410' of git://git.kernel.dk/linux:
ublk: pass ublksrv_ctrl_cmd * instead of io_uring_cmd *
ublk: don't fail request for recovery & reissue in case of ubq->canceling
ublk: fix handling recovery & reissue in ublk_abort_queue()
selftests: ublk: fix test_stripe_04
Pull io_uring fixes from Jens Axboe:
- Reject zero sized legacy provided buffers upfront. No ill side
effects from this one, only really done to shut up a silly syzbot
test case.
- Fix for a regression in tag posting for registered files or buffers,
where the tag would be posted even when the registration failed.
- two minor zcrx cleanups for code added this merge window.
* tag 'io_uring-6.15-20250410' of git://git.kernel.dk/linux:
io_uring/kbuf: reject zero sized provided buffers
io_uring/zcrx: separate niov number from pages
io_uring/zcrx: put refill data into separate cache line
io_uring: don't post tag CQEs on file/buffer registration failure
Pull gpio fixes from Bartosz Golaszewski:
- fix resource handling in gpio-tegra186
- fix wakeup source leaks in gpio-mpc8xxx and gpio-zynq
- fix minor issues with some GPIO OF quirks
- deprecate GPIOD_FLAGS_BIT_NONEXCLUSIVE and devm_gpiod_unhinge()
symbols and add a TODO task to track replacing them with a better
solution
* tag 'gpio-fixes-for-v6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: of: Move Atmel HSMCI quirk up out of the regulator comment
gpiolib: of: Fix the choice for Ingenic NAND quirk
gpio: zynq: Fix wakeup source leaks on device unbind
gpio: mpc8xxx: Fix wakeup source leaks on device unbind
gpio: TODO: track the removal of regulator-related workarounds
MAINTAINERS: add more keywords for the GPIO subsystem entry
gpio: deprecate devm_gpiod_unhinge()
gpio: deprecate the GPIOD_FLAGS_BIT_NONEXCLUSIVE flag
gpio: tegra186: fix resource handling in ACPI probe path
Pull mtd fixes from Miquel Raynal:
"Two important fixes: the build of the SPI NAND layer with old GCC
versions as well as the fix of the Qpic Makefile which was wrong in
the first place.
There are also two smaller fixes about a missing error and status
check"
* tag 'mtd/fixes-for-6.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spinand: Fix build with gcc < 7.5
mtd: rawnand: Add status chack in r852_ready()
mtd: inftlcore: Add error check for inftl_read_oob()
mtd: nand: Drop explicit test for built-in CONFIG_SPI_QPIC_SNAND
The 'read_write_len_ext' field in 'struct ethtool_cmis_cdb_cmd_args'
stores the maximum number of bytes that can be read from or written to
the Local Payload (LPL) page in a single multi-byte access.
Cited commit started overwriting this field with the maximum number of
bytes that can be read from or written to the Extended Payload (LPL)
pages in a single multi-byte access. Transceiver modules that support
auto paging can advertise a number larger than 255 which is problematic
as 'read_write_len_ext' is a 'u8', resulting in the number getting
truncated and firmware flashing failing [1].
Fix by ignoring the maximum EPL access size as the kernel does not
currently support auto paging (even if the transceiver module does) and
will not try to read / write more than 128 bytes at once.
[1]
Transceiver module firmware flashing started for device enp177s0np0
Transceiver module firmware flashing in progress for device enp177s0np0
Progress: 0%
Transceiver module firmware flashing encountered an error for device enp177s0np0
Status message: Write FW block EPL command failed, LPL length is longer
than CDB read write length extension allows.
Fixes: 9a3b0d078b ("net: ethtool: Add support for writing firmware blocks using EPL payload")
Reported-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Closes: https://lore.kernel.org/netdev/20250402183123.321036-3-michael.chan@broadcom.com/
Tested-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20250409112440.365672-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following batch contains a Netfilter fix and improved test coverage:
1) Fix AVX2 matching in nft_pipapo, from Florian Westphal.
2) Extend existing test to improve coverage for the aforementioned bug,
also from Florian.
netfilter pull request 25-04-10
* tag 'nf-25-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
selftests: netfilter: add test case for recent mismatch bug
nft_set_pipapo: fix incorrect avx2 match of 5th field octet
====================
Link: https://patch.msgid.link/20250410103647.1030244-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
