To increase the flexibility of supporting different DP main link configuration
at different platform, add both data-lanes and link-frequencies property
into endpoint so that different platform can specify its own main link
combination of both data lanes and max supported link rate.
Changes in v7:
-- split yaml out of dtsi patch
-- link-frequencies from link rate to symbol rate
-- deprecation of old data-lanes property
Changes in v8:
-- correct Bjorn mail address to kernel.org
Changes in v10:
-- add menu item to data-lanes and link-frequecnis
Changes in v11:
-- add endpoint property at port@1
Changes in v12:
-- use enum for item at data-lanes and link-frequencies
Changes in v13:
-- revised changes at port@0
-- use correct ref schemas for both port@0 and port@1
-- mark both port@0 and port@1 are required
-- add line between data-lanes and link-frequencies properties
Changes in v14:
-- add "unevaluatedProperties: false: to endpoint at port@1
-- remove unnecessary quote to $ref
-- re store "$ref: /schemas/graph.yaml#/properties/port" to port@0
Changes in v15:
-- re store desciption of port@0
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/516094/
Link: https://lore.kernel.org/r/1672163103-31254-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DisplayPort controller's hot-plug mechanism is based on pinmuxing a
physical signal on a GPIO pin into the controller. This is not always
possible, either because there aren't dedicated GPIOs available or
because the hot-plug signal is a virtual notification, in cases such as
USB Type-C.
For these cases, by implementing the hpd_notify() callback for the
DisplayPort controller's drm_bridge, a downstream drm_bridge
(next_bridge) can be used to track and signal the connection status
changes.
This makes it possible to use downstream drm_bridges such as
display-connector or any virtual mechanism, as long as they are
implemented as a drm_bridge.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[bjorn: Drop connector->fwnode assignment and dev from struct msm_dp]
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514410/
Link: https://lore.kernel.org/r/20221207220012.16529-10-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DisplayPort controller's internal HPD interrupt handling is used for
cases where the HPD signal is connected to a GPIO which is pinmuxed into
the DisplayPort controller. In other configurations the HPD notification
might be delivered by the DRM framework from an associated bridge.
This difference is not appropriately represented by the "is_edp"
boolean, but is properly represented by the frameworks invocation of the
hpd_enable() and hpd_disable() callbacks. Switch the current condition
to rely on these callbacks instead.
This ensures appropriate handling of the three cases; no bridge
connected, a bridge without DRM_BRIDGE_OP_HPD and a bridge with
DRM_BRIDGE_OP_HPD.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514414/
Link: https://lore.kernel.org/r/20221207220012.16529-9-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
power-domain is required for the sc7180 dispcc GDSC but not every qcom SoC
has a similar dependency for example the apq8064.
Most Qcom SoC's using mdss-dsi-ctrl seem to have the ability to
power-collapse the MDP without collapsing DSI.
For example the qcom vendor kernel commit for apq8084, msm8226, msm8916,
msm8974.
7b5c011a77
"ARM: dts: msm: add mdss gdsc supply to dsi controller device
It is possible for the DSI controller to be active when MDP is
power collapsed. DSI controller needs to have it's own vote for
mdss gdsc to ensure that gdsc remains on in such cases."
This however doesn't appear to be the case for the apq8064 so we shouldn't
be marking power-domain as required in yaml checks.
Fixes: 4dbe55c977 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515958/
Link: https://lore.kernel.org/r/20221223021025.1646636-3-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
There are 3 possible interrupt sources are handled by DP controller,
HPDstatus, Controller state changes and Aux read/write transaction.
At every irq, DP controller have to check isr status of every interrupt
sources and service the interrupt if its isr status bits shows interrupts
are pending. There is potential race condition may happen at current aux
isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
even irq is not for aux read or write transaction. This may cause aux read
transaction return premature if host aux data read is in the middle of
waiting for sink to complete transferring data to host while irq happen.
This will cause host's receiving buffer contains unexpected data. This
patch fixes this problem by checking aux isr and return immediately at
aux isr handler if there are no any isr status bits set.
Current there is a bug report regrading eDP edid corruption happen during
system booting up. After lengthy debugging to found that VIDEO_READY
interrupt was continuously firing during system booting up which cause
dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
from aux hardware buffer which is not yet contains complete data transfer
from sink. This cause edid corruption.
Follows are the signature at kernel logs when problem happen,
EDID has corrupt header
panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID
Changes in v2:
-- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
-- add more commit text
Changes in v3:
-- add Stephen suggested
-- dp_aux_isr() return IRQ_XXX back to caller
-- dp_ctrl_isr() return IRQ_XXX back to caller
Changes in v4:
-- split into two patches
Changes in v5:
-- delete empty line between tags
Changes in v6:
-- remove extra "that" and fixed line more than 75 char at commit text
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516121/
Link: https://lore.kernel.org/r/1672193785-11003-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Adding in msm8939 which is based msm8916 dtsi I stumbled across a binding
check complaining about the phy name for msm8916 which we were reusing for
msm8939.
The currently inconsistent upstream dtsi naming of "dsi" and "dsi-phy" is
not captured in the yaml for this driver.
The driver however doesn't care about the name of DSI phy, hence the yaml
check is redundant.
Both Krzysztof and Rob suggested we could drop the phy-names entirely if it
really isn't a dependency.
So, drop the inconsistent and unnecessary phy-names field from the yaml.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to the comment this DPU register contains the bits per pixel
as a 6.4 fractional value, conveniently matching the contents of
bits_per_pixel in struct drm_dsc_config which also uses 4 fractional
bits. However, the downstream source this implementation was
copy-pasted from has its bpp field stored _without_ fractional part.
This makes the entire convoluted math obsolete as it is impossible to
pull those 4 fractional bits out of thin air, by somehow trying to reuse
the lowest 2 bits of a non-fractional bpp (lsb = bpp % 4??).
The rest of the code merely attempts to keep the integer part a multiple
of 4, which is rendered useless thanks to data |= dsc->bits_per_pixel <<
12; already filling up those bits anyway (but not on downstream).
Fixes: c110cfd175 ("drm/msm/disp/dpu1: Add support for DSC")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/508946/
Link: https://lore.kernel.org/r/20221026182824.876933-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
drm_dsc_config's bits_per_pixel field holds a fractional value with 4
bits, which all panel drivers should adhere to for
drm_dsc_pps_payload_pack() to generate a valid payload. All code in the
DSI driver here seems to assume that this field doesn't contain any
fractional bits, hence resulting in the wrong values being computed.
Since none of the calculations leave any room for fractional bits or
seem to indicate any possible area of support, disallow such values
altogether. calculate_rc_params() in intel_vdsc.c performs an identical
bitshift to get at this integer value.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508938/
Link: https://lore.kernel.org/r/20221026182824.876933-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As per the FIXME this code is entirely duplicate with what is already
provided inside drm_dsc_compute_rc_parameters(), supposedly because that
function was yielding "incorrect" results while in reality the panel
driver(s?) used for testing were providing incorrect parameters.
For example, this code from downstream assumed dsc->bits_per_pixel to
contain an integer value, whereas the upstream drm_dsc_config struct
stores it with 4 fractional bits. drm_dsc_compute_rc_parameters()
already accounts for this feat while the panel driver used for testing
[1] wasn't, hence making drm_dsc_compute_rc_parameters() seem like it
was returning an incorrect result.
Other users of dsc->bits_per_pixel inside dsi_populate_dsc_params() also
treat it in the same erroneous way, and will be addressed in a separate
patch.
In the end, using drm_dsc_compute_rc_parameters() spares both a lot of
duplicate code and erratic behaviour.
[1]: https://git.linaro.org/people/vinod.koul/kernel.git/commit/?h=topic/pixel3_5.18-rc1&id=1d7d98ad564f1ec69e7525e07418918d90f247a1
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508939/
Link: https://lore.kernel.org/r/20221026182824.876933-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This field is currently unread but will come into effect when duplicated
code below is migrated to call drm_dsc_compute_rc_parameters(), which
uses the bpc-dependent value of the local variable mux_words_size in
much the same way.
The hardcoded constant seems to be a remnant from the `/* bpc 8 */`
comment right above, indicating that this group of field assignments is
applicable to bpc = 8 exclusively and should probably bail out on
different bpc values, until constants for other bpc values are added (or
the current ones are confirmed to be correct across multiple bpc's).
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508943/
Link: https://lore.kernel.org/r/20221026182824.876933-6-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to the comment this DPU register contains the bits per pixel
as a 6.4 fractional value, conveniently matching the contents of
bits_per_pixel in struct drm_dsc_config which also uses 4 fractional
bits. However, the downstream source this implementation was
copy-pasted from has its bpp field stored _without_ fractional part.
This makes the entire convoluted math obsolete as it is impossible to
pull those 4 fractional bits out of thin air, by somehow trying to reuse
the lowest 2 bits of a non-fractional bpp (lsb = bpp % 4??).
The rest of the code merely attempts to keep the integer part a multiple
of 4, which is rendered useless thanks to data |= dsc->bits_per_pixel <<
12; already filling up those bits anyway (but not on downstream).
Fixes: c110cfd175 ("drm/msm/disp/dpu1: Add support for DSC")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/508946/
Link: https://lore.kernel.org/r/20221026182824.876933-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
