When CONFIG_DEVFREQ_THERMAL is disabled all functions except
of_devfreq_cooling_register_power() were already inlined. Also inline
the last function to avoid compile errors when multiple drivers call
of_devfreq_cooling_register_power() when CONFIG_DEVFREQ_THERMAL is not
set. Compilation failed with the following message:
multiple definition of `of_devfreq_cooling_register_power'
(which then lists all usages of of_devfreq_cooling_register_power())
Thomas Zimmermann reported this problem [0] on a kernel config with
CONFIG_DRM_LIMA={m,y}, CONFIG_DRM_PANFROST={m,y} and
CONFIG_DEVFREQ_THERMAL=n after both, the lima and panfrost drivers
gained devfreq cooling support.
[0] https://www.spinics.net/lists/dri-devel/msg252825.html
Fixes: a76caf55e5 ("thermal: Add devfreq cooling")
Cc: stable@vger.kernel.org
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200403205133.1101808-1-martin.blumenstingl@googlemail.com
The WARN_ON macros are used at the entry functions state2power() and
set_cur_state().
state2power() is called with the max_state retrieved from
get_max_state which returns cpufreq_cdev->max_level, then it check if
max_state is > cpufreq_cdev->max_level. The test does not really makes
sense but let's assume we want to make sure to catch an error if the
code evolves. However the WARN_ON is overkill.
set_cur_state() is also called from userspace if we write to the
sysfs. It is easy to see a stack dumped by just writing to sysfs
/sys/class/thermal/cooling_device0/cur_state a value greater than
"max_level". A bit scary. Returing -EINVAL is enough.
Remove these WARN_ON.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20200321193107.21590-1-daniel.lezcano@linaro.org
When setting the cooling device current state from userspace via sysfs,
the operation fails by returning an -EINVAL.
It appears the recent changes with the per-policy frequency QoS
introduced a regression as reported by:
https://lkml.org/lkml/2020/3/20/599
The function freq_qos_update_request returns 0 or 1 describing update
effectiveness, and a negative error code on failure. However,
cpufreq_set_cur_state returns 0 on success or an error code otherwise.
Consider the QoS update as successful if the function does not return
an error.
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Signed-off-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200321092740.7vvwfxsebcrznydh@macmini.local
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200319184838.GA25767@embeddedor.com
Cooling-maps doesn't have to be a required property because there may
be no cooling device on system, or there are no enough cooling devices for
each thermal zone in multiple thermal zone cases since cooling devices
can't be shared.
So make this property optional to remove such limitations.
For thermal zones with no cooling-maps, there could be critic trips
that can trigger CPU reset or shutdown. So they still can take actions.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200309045411.21859-1-andy.tang@nxp.com
imx_thermal_unregister_legacy_cooling() should be used for handling
legacy cpufreq cooling cleanups in .remove callback instead of
calling cpufreq_cooling_unregister() and cpufreq_cpu_put() directly,
especially for !CONFIG_CPU_FREQ scenario, no operation needed for
handling legacy cpufreq cooling cleanups at all.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584088094-24857-1-git-send-email-Anson.Huang@nxp.com
We don't currently call put_device in case of successfully initialising
the device. So we hold the reference and keep the device pinned forever.
Allow control to fall through so we can use same code for success and
error paths to put_device.
As a part of this fixup, change devm_ioremap_resource to act on the same
device pointer as that used to allocate regmap memory. That ensures that
we are free to release op->dev after examining its resources.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/d3996667e9f976bb30e97e301585cb1023be422e.1584015867.git.amit.kucheria@linaro.org
Add "inline" to thermal_zone_of_get_sensor_id() function to avoid below
build warning of !defined(CONFIG_THERMAL_OF).
In file included from drivers/hwmon/hwmon.c:22:
include/linux/thermal.h:382:12: warning: 'thermal_zone_of_get_sensor_id'
defined but not used [-Wunused-function]
382 | static int thermal_zone_of_get_sensor_id(struct device_node *tz_np,
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1583222684-10229-1-git-send-email-Anson.Huang@nxp.com
The thermal subsystem may have relied on sysfs in 2008 when it
was introduced, but these days the thermal zones will more often
than not come from the hardware descriptions and not from sysfs.
Drop the "Generic" phrases as well: there are no non-generic
drivers that I know of, the thermal framework is by definition
generic.
Reword a bit and fix some grammar.
[ Daniel Lezcano ] : fixed Randy's comment s/offers/offer/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200229204527.143796-1-linus.walleij@linaro.org
i.MX8QXP is an ARMv8 SoC which has a Cortex-M4 system controller
inside, the system controller is in charge of controlling power,
clock and thermal sensors etc..
This patch adds i.MX system controller thermal driver support,
Linux kernel has to communicate with system controller via MU
(message unit) IPC to get each thermal sensor's temperature,
it supports multiple sensors which are passed from device tree,
please see the binding doc for details.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582330132-13461-3-git-send-email-Anson.Huang@nxp.com
NXP i.MX8QXP is an ARMv8 SoC with a Cortex-M4 core inside as
system controller, the system controller is in charge of system
power, clock and thermal sensors etc. management, Linux kernel
has to communicate with system controller via MU (message unit)
IPC to get temperature from thermal sensors, this patch adds
binding doc for i.MX system controller thermal driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582330132-13461-1-git-send-email-Anson.Huang@nxp.com
The desired behavior of the driver is to generate an interrupt and call
thermal_zone_device_update() as soon as the temperature have changed
more then one degree.
When the set_trips operation was implemented it was believed that the
trip window set by the framework would move around the current
temperature and the hysteresis value described in devicetree. The
behavior of the framework is however to set a window based on the trip
points described in devicetree.
Remove the set_trips operation which was not used correctly and update
the temperatures that triggers interrupts directly from the interrupt
handler.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200212224917.737314-1-niklas.soderlund+renesas@ragnatech.se
