Pull gpio fixes from Bartosz Golaszewski:
- fix kerneldocs for gpio-timberdale and gpio-nomadik
- clear the "requested" flag in error path in gpiod_request_commit()
- call of_xlate() if provided when setting up shared GPIOs
- handle pins shared by child firmware nodes of consumer devices
- fix return value check in gpio-qixis-fpga
- fix suspend on gpio-mxc
- fix gpio-microchip DT bindings
* tag 'gpio-fixes-for-v7.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
dt-bindings: gpio: fix microchip #interrupt-cells
gpio: shared: shorten the critical section in gpiochip_setup_shared()
gpio: mxc: map Both Edge pad wakeup to Rising Edge
gpio: qixis-fpga: Fix error handling for devm_regmap_init_mmio()
gpio: shared: handle pins shared by child nodes of devices
gpio: shared: call gpio_chip::of_xlate() if set
gpiolib: clear requested flag if line is invalid
gpio: nomadik: repair some kernel-doc comments
gpio: timberdale: repair kernel-doc comments
gpio: Fix resource leaks on errors in gpiochip_add_data_with_key()
Pull arm64 fix from Will Deacon:
- Implement a basic static call trampoline to fix CFI failures with the
generic implementation
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Use static call trampolines when kCFI is enabled
Pull drm fixes from Dave Airlie:
"Hopefully no Easter eggs in this bunch of fixes. Usual stuff across
the amd/intel with some misc bits. Thanks to Thorsten and Alex for
making sure a regression fix that was hanging around in process land
finally made it in, that is probably the biggest change in here.
core:
- revert unplug/framebuffer fix as it caused problems
- compat ioctl speculation fix
bridge:
- refcounting fix
sysfb:
- error handling fix
amdgpu:
- fix renoir audio regression
- UserQ fixes
- PASID handling fix
- S4 fix for smu11 chips
- Misc small fixes
amdkfd:
- Non-4K page fixes
i915:
- Fix for #12045: Huawei Matebook E (DRR-WXX): Persistent Black
Screen on Boot with i915 and Gen11: Modesetting and Backlight
Control Malfunction
- Fix for #15826: i915: Raptor Lake-P [UHD Graphics] display
flicker/corruption on eDP panel
- Use crtc_state->enhanced_framing properly on ivb/hsw CPU eDP
xe:
- uapi: Accept canonical GPU addresses in xe_vm_madvise_ioctl
- Disallow writes to read-only VMAs
- PXP fixes
- Disable garbage collector work item on SVM close
- void memory allocations in xe_device_declare_wedged
qaic:
- hang fix
ast:
- initialisation fix"
* tag 'drm-fixes-2026-04-03' of https://gitlab.freedesktop.org/drm/kernel: (28 commits)
drm/amd/display: Wire up dcn10_dio_construct() for all pre-DCN401 generations
drm/ioc32: stop speculation on the drm_compat_ioctl path
drm/sysfb: Fix efidrm error handling and memory type mismatch
drm/i915/dp: Use crtc_state->enhanced_framing properly on ivb/hsw CPU eDP
drm/i915/cdclk: Do the full CDCLK dance for min_voltage_level changes
drm/amdkfd: Fix queue preemption/eviction failures by aligning control stack size to GPU page size
drm/amdgpu: Fix wait after reset sequence in S4
drm/amd/display: Fix NULL pointer dereference in dcn401_init_hw()
drm/amdgpu: Change AMDGPU_VA_RESERVED_TRAP_SIZE to 64KB
drm/amdgpu/userq: fix memory leak in MQD creation error paths
drm/amd: Fix MQD and control stack alignment for non-4K
drm/amdkfd: Align expected_queue_size to PAGE_SIZE
drm/amdgpu: fix the idr allocation flags
drm/amdgpu: validate doorbell_offset in user queue creation
drm/amdgpu/pm: drop SMU driver if version not matched messages
drm/xe: Avoid memory allocations in xe_device_declare_wedged()
drm/xe: Disable garbage collector work item on SVM close
drm/xe/pxp: Don't allow PXP on older PTL GSC FWs
drm/xe/pxp: Clear restart flag in pxp_start after jumping back
drm/xe/pxp: Remove incorrect handling of impossible state during suspend
...
A refcounting fix for bridges, revert a previous framebuffer
use-after-free fix that turned out to be causing more problems, a hang
fix for qaic, an initialization fix for ast, a error handling fix for
sysfb, and a speculation fix for drm_compat_ioctl.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patch.msgid.link/20260402-vivid-perfect-caiman-ca055e@houat
- Fix for #12045: Huawei Matebook E (DRR-WXX): Persistent Black Screen on Boot with i915 and Gen11: Modesetting and Backlight Control Malfunction
- Fix for #15826: i915: Raptor Lake-P [UHD Graphics] display flicker/corruption on eDP panel
- Use crtc_state->enhanced_framing properly on ivb/hsw CPU eDP
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patch.msgid.link/ac5DM1IpBkuaT58e@jlahtine-mobl
Pull smb client fix from Steve French:
- Fix potential out of bounds read in mount
* tag 'v7.0-rc6-smb3-client-fix' of git://git.samba.org/sfrench/cifs-2.6:
fs/smb/client: fix out-of-bounds read in cifs_sanitize_prepath
Pull bpf fixes from Alexei Starovoitov:
- Fix register equivalence for pointers to packet (Alexei Starovoitov)
- Fix incorrect pruning due to atomic fetch precision tracking (Daniel
Borkmann)
- Fix grace period wait for bpf_link-ed tracepoints (Kumar Kartikeya
Dwivedi)
- Fix use-after-free of sockmap's sk->sk_socket (Kuniyuki Iwashima)
- Reject direct access to nullable PTR_TO_BUF pointers (Qi Tang)
- Reject sleepable kprobe_multi programs at attach time (Varun R
Mallya)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Add more precision tracking tests for atomics
bpf: Fix incorrect pruning due to atomic fetch precision tracking
bpf: Reject sleepable kprobe_multi programs at attach time
bpf: reject direct access to nullable PTR_TO_BUF pointers
bpf: sockmap: Fix use-after-free of sk->sk_socket in sk_psock_verdict_data_ready().
bpf: Fix grace period wait for tracepoint bpf_link
bpf: Fix regsafe() for pointers to packet
Pull crypto fixes from Herbert Xu:
- Add missing async markers to tegra
- Fix long hmac key DMA handling in caam
- Fix spurious ENOSPC errors in deflate
- Fix SG chaining in af_alg
- Do not use in-place process in algif_aead
- Fix out-of-place destination overflow in authencesn
* tag 'v7.0-p4' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authencesn - Do not place hiseq at end of dst for out-of-place decryption
crypto: algif_aead - Revert to operating out-of-place
crypto: af-alg - fix NULL pointer dereference in scatterwalk
crypto: deflate - fix spurious -ENOSPC
crypto: caam - fix overflow on long hmac keys
crypto: caam - fix DMA corruption on long hmac keys
crypto: tegra - Add missing CRYPTO_ALG_ASYNC
Description:
- Commit b82f075934 ("drm/amd/display: Migrate DIO registers access
from hwseq to dio component") moved DIO_MEM_PWR_CTRL register access
behind the new dio abstraction layer but only created the dio object for
DCN 4.01. On all other generations (DCN 10/20/21/201/30/301/302/303/
31/314/315/316/32/321/35/351/36), the dio pointer is NULL, causing the
register write to be silently skipped.
This results in AFMT HDMI memory not being powered on during init_hw,
which can cause HDMI audio failures and display issues on affected
hardware including Renoir/Cezanne (DCN 2.1) APUs that use dcn10_init_hw.
Call dcn10_dio_construct() in each older DCN generation's resource.c
to create the dio object, following the same pattern as DCN 4.01. This
ensures the dio pointer is non-NULL and the mem_pwr_ctrl callback works
through the dio abstraction for all DCN generations.
Fixes: b82f075934 ("drm/amd/display: Migrate DIO registers access from hwseq to dio component.")
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Ionut Nechita <ionut_n2001@yahoo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull smb server fix from Steve French:
- Fix out of bound write
* tag 'v7.0-rc6-ksmbd-server-fix' of git://git.samba.org/ksmbd:
ksmbd: fix OOB write in QUERY_INFO for compound requests
Pull btrfs fix from David Sterba:
"One more fix for a potential extent tree corruption due to an
unexpected error value.
When the search for an extent item failed, it under some circumstances
was reported as a success to the caller"
* tag 'for-7.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix incorrect return value after changing leaf in lookup_extent_data_ref()
Add verifier precision tracking tests for BPF atomic fetch operations.
Validate that backtrack_insn correctly propagates precision from the
fetch dst_reg to the stack slot for {fetch_add,xchg,cmpxchg} atomics.
For the first two src_reg gets the old memory value, and for the last
one r0. The fetched register is used for pointer arithmetic to trigger
backtracking. Also add coverage for fetch_{or,and,xor} flavors which
exercises the bitwise atomic fetch variants going through the same
insn->imm & BPF_FETCH check but with different imm values.
Add dual-precision regression tests for fetch_add and cmpxchg where
both the fetched value and a reread of the same stack slot are tracked
for precision. After the atomic operation, the stack slot is STACK_MISC,
so the ldx does not set INSN_F_STACK_ACCESS. These tests verify that
stack precision propagates solely through the atomic fetch's load side.
Add map-based tests for fetch_add and cmpxchg which validate that non-
stack atomic fetch completes precision tracking without falling back
to mark_all_scalars_precise. Lastly, add 32-bit variants for {fetch_add,
cmpxchg} on map values to cover the second valid atomic operand size.
# LDLIBS=-static PKG_CONFIG='pkg-config --static' ./vmtest.sh -- ./test_progs -t verifier_precision
[...]
+ /etc/rcS.d/S50-startup
./test_progs -t verifier_precision
[ 1.697105] bpf_testmod: loading out-of-tree module taints kernel.
[ 1.700220] bpf_testmod: module verification failed: signature and/or required key missing - tainting kernel
[ 1.777043] tsc: Refined TSC clocksource calibration: 3407.986 MHz
[ 1.777619] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x311fc6d7268, max_idle_ns: 440795260133 ns
[ 1.778658] clocksource: Switched to clocksource tsc
#633/1 verifier_precision/bpf_neg:OK
#633/2 verifier_precision/bpf_end_to_le:OK
#633/3 verifier_precision/bpf_end_to_be:OK
#633/4 verifier_precision/bpf_end_bswap:OK
#633/5 verifier_precision/bpf_load_acquire:OK
#633/6 verifier_precision/bpf_store_release:OK
#633/7 verifier_precision/state_loop_first_last_equal:OK
#633/8 verifier_precision/bpf_cond_op_r10:OK
#633/9 verifier_precision/bpf_cond_op_not_r10:OK
#633/10 verifier_precision/bpf_atomic_fetch_add_precision:OK
#633/11 verifier_precision/bpf_atomic_xchg_precision:OK
#633/12 verifier_precision/bpf_atomic_fetch_or_precision:OK
#633/13 verifier_precision/bpf_atomic_fetch_and_precision:OK
#633/14 verifier_precision/bpf_atomic_fetch_xor_precision:OK
#633/15 verifier_precision/bpf_atomic_cmpxchg_precision:OK
#633/16 verifier_precision/bpf_atomic_fetch_add_dual_precision:OK
#633/17 verifier_precision/bpf_atomic_cmpxchg_dual_precision:OK
#633/18 verifier_precision/bpf_atomic_fetch_add_map_precision:OK
#633/19 verifier_precision/bpf_atomic_cmpxchg_map_precision:OK
#633/20 verifier_precision/bpf_atomic_fetch_add_32bit_precision:OK
#633/21 verifier_precision/bpf_atomic_cmpxchg_32bit_precision:OK
#633/22 verifier_precision/bpf_neg_2:OK
#633/23 verifier_precision/bpf_neg_3:OK
#633/24 verifier_precision/bpf_neg_4:OK
#633/25 verifier_precision/bpf_neg_5:OK
#633 verifier_precision:OK
Summary: 1/25 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20260331222020.401848-2-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When backtrack_insn encounters a BPF_STX instruction with BPF_ATOMIC
and BPF_FETCH, the src register (or r0 for BPF_CMPXCHG) also acts as
a destination, thus receiving the old value from the memory location.
The current backtracking logic does not account for this. It treats
atomic fetch operations the same as regular stores where the src
register is only an input. This leads the backtrack_insn to fail to
propagate precision to the stack location, which is then not marked
as precise!
Later, the verifier's path pruning can incorrectly consider two states
equivalent when they differ in terms of stack state. Meaning, two
branches can be treated as equivalent and thus get pruned when they
should not be seen as such.
Fix it as follows: Extend the BPF_LDX handling in backtrack_insn to
also cover atomic fetch operations via is_atomic_fetch_insn() helper.
When the fetch dst register is being tracked for precision, clear it,
and propagate precision over to the stack slot. For non-stack memory,
the precision walk stops at the atomic instruction, same as regular
BPF_LDX. This covers all fetch variants.
Before:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs=r2 stack= before 2: (b7) r2 = 0
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit
After:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs= stack=-8 before 2: (b7) r2 = 0
mark_precise: frame0: regs= stack=-8 before 1: (7b) *(u64 *)(r10 -8) = r1
mark_precise: frame0: regs=r1 stack= before 0: (b7) r1 = 8
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit
Fixes: 5ffa25502b ("bpf: Add instructions for atomic_[cmp]xchg")
Fixes: 5ca419f286 ("bpf: Add BPF_FETCH field / create atomic_fetch_add instruction")
Reported-by: STAR Labs SG <info@starlabs.sg>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20260331222020.401848-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking fixes from Jakub Kicinski:
"With fixes from wireless, bluetooth and netfilter included we're back
to each PR carrying 30%+ more fixes than in previous era.
The good news is that so far none of the "extra" fixes are themselves
causing real regressions. Not sure how much comfort that is.
Current release - fix to a fix:
- netdevsim: fix build if SKB_EXTENSIONS=n
- eth: stmmac: skip VLAN restore when VLAN hash ops are missing
Previous releases - regressions:
- wifi: iwlwifi: mvm: don't send a 6E related command when
not supported
Previous releases - always broken:
- some info leak fixes
- add missing clearing of skb->cb[] on ICMP paths from tunnels
- ipv6:
- flowlabel: defer exclusive option free until RCU teardown
- avoid overflows in ip6_datagram_send_ctl()
- mpls: add seqcount to protect platform_labels from OOB access
- bridge: improve safety of parsing ND options
- bluetooth: fix leaks, overflows and races in hci_sync
- netfilter: add more input validation, some to address bugs directly
some to prevent exploits from cooking up broken configurations
- wifi:
- ath: avoid poor performance due to stopping the wrong
aggregation session
- virt_wifi: remove SET_NETDEV_DEV to avoid use-after-free
- eth:
- fec: fix the PTP periodic output sysfs interface
- enetc: safely reinitialize TX BD ring when it has unsent frames"
* tag 'net-7.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
eth: fbnic: Increase FBNIC_QUEUE_SIZE_MIN to 64
ipv6: avoid overflows in ip6_datagram_send_ctl()
net: hsr: fix VLAN add unwind on slave errors
net: hsr: serialize seq_blocks merge across nodes
vsock: initialize child_ns_mode_locked in vsock_net_init()
selftests/tc-testing: add tests for cls_fw and cls_flow on shared blocks
net/sched: cls_flow: fix NULL pointer dereference on shared blocks
net/sched: cls_fw: fix NULL pointer dereference on shared blocks
net/x25: Fix overflow when accumulating packets
net/x25: Fix potential double free of skb
bnxt_en: Restore default stat ctxs for ULP when resource is available
bnxt_en: Don't assume XDP is never enabled in bnxt_init_dflt_ring_mode()
bnxt_en: Refactor some basic ring setup and adjustment logic
net/mlx5: Fix switchdev mode rollback in case of failure
net/mlx5: Avoid "No data available" when FW version queries fail
net/mlx5: lag: Check for LAG device before creating debugfs
net: macb: properly unregister fixed rate clocks
net: macb: fix clk handling on PCI glue driver removal
virtio_net: clamp rss_max_key_size to NETDEV_RSS_KEY_LEN
net/sched: sch_netem: fix out-of-bounds access in packet corruption
...
Pull iommu fixes from Joerg Roedel:
- IOMMU-PT related compile breakage in for AMD driver
- IOTLB flushing behavior when unmapped region is larger than requested
due to page-sizes
- Fix IOTLB flush behavior with empty gathers
* tag 'iommu-fixes-v7.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommupt/amdv1: mark amdv1pt_install_leaf_entry as __always_inline
iommupt: Fix short gather if the unmap goes into a large mapping
iommu: Do not call drivers for empty gathers
kprobe.multi programs run in atomic/RCU context and cannot sleep.
However, bpf_kprobe_multi_link_attach() did not validate whether the
program being attached had the sleepable flag set, allowing sleepable
helpers such as bpf_copy_from_user() to be invoked from a non-sleepable
context.
This causes a "sleeping function called from invalid context" splat:
BUG: sleeping function called from invalid context at ./include/linux/uaccess.h:169
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1787, name: sudo
preempt_count: 1, expected: 0
RCU nest depth: 2, expected: 0
Fix this by rejecting sleepable programs early in
bpf_kprobe_multi_link_attach(), before any further processing.
Fixes: 0dcac27254 ("bpf: Add multi kprobe link")
Signed-off-by: Varun R Mallya <varunrmallya@gmail.com>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Leon Hwang <leon.hwang@linux.dev>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20260401191126.440683-1-varunrmallya@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
check_mem_access() matches PTR_TO_BUF via base_type() which strips
PTR_MAYBE_NULL, allowing direct dereference without a null check.
Map iterator ctx->key and ctx->value are PTR_TO_BUF | PTR_MAYBE_NULL.
On stop callbacks these are NULL, causing a kernel NULL dereference.
Add a type_may_be_null() guard to the PTR_TO_BUF branch, matching the
existing PTR_TO_BTF_ID pattern.
Fixes: 20b2aff4bc ("bpf: Introduce MEM_RDONLY flag")
Signed-off-by: Qi Tang <tpluszz77@gmail.com>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20260402092923.38357-2-tpluszz77@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull sound fixes from Takashi Iwai:
"People have been so busy for hunting and we're still getting more
changes than wished for, but it doesn't look too scary; almost all
changes are device-specific small fixes.
I guess it's rather a casual bump, and no more Easter eggs are left
for 7.0 (hopefully)...
- Fixes for the recent regression on ctxfi driver
- Fix missing INIT_LIST_HEAD() for ASoC card_aux_list
- Usual HD- and USB-audio, and ASoC AMD quirk updates
- ASoC fixes for AMD and Intel"
* tag 'sound-7.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ASoC: amd: ps: Fix missing leading zeros in subsystem_device SSID log
ALSA: usb-audio: Exclude Scarlett 2i2 1st Gen (8016) from SKIP_IFACE_SETUP
ALSA: hda/realtek: add quirk for Acer Swift SFG14-73
ALSA: hda/realtek: Add quirk for Lenovo Yoga Pro 7 14IMH9
ASoC: Intel: boards: fix unmet dependency on PINCTRL
ASoC: Intel: ehl_rt5660: Use the correct rtd->dev device in hw_params
ALSA: ctxfi: Don't enumerate SPDIF1 at DAIO initialization
ALSA: hda/realtek: Add quirk for Lenovo Yoga Slim 7 14AKP10
ALSA: hda/realtek: add quirk for HP Laptop 15-fc0xxx
ASoC: ep93xx: Fix unchecked clk_prepare_enable() and add rollback on failure
ASoC: soc-core: call missing INIT_LIST_HEAD() for card_aux_list
ALSA: hda/realtek: Add quirk for Samsung Book2 Pro 360 (NP950QED)
ASoC: amd: yc: Add DMI entry for HP Laptop 15-fc0xxx
ASoC: amd: yc: Add DMI quirk for ASUS Vivobook Pro 16X OLED M7601RM
ALSA: hda/realtek: Add quirk for ASUS ROG Strix SCAR 15
ALSA: usb-audio: Exclude Scarlett Solo 1st Gen from SKIP_IFACE_SETUP
ALSA: caiaq: fix stack out-of-bounds read in init_card
ALSA: ctxfi: Check the error for index mapping
ALSA: ctxfi: Fix missing SPDIFI1 index handling
ALSA: hda/realtek: add quirk for HP Victus 15-fb0xxx
...
Pull auxdisplay fixes from Andy Shevchenko:
- Fix NULL dereference in linedisp_release()
- Fix ht16k33 DT bindings to avoid warnings
- Handle errors in I²C transfers in lcd2s driver
* tag 'auxdisplay-v7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-auxdisplay:
auxdisplay: line-display: fix NULL dereference in linedisp_release
auxdisplay: lcd2s: add error handling for i2c transfers
dt-bindings: auxdisplay: ht16k33: Use unevaluatedProperties to fix common property warning
On systems with 64K pages, RX queues will be wedged if users set the
descriptor count to the current minimum (16). Fbnic fragments large
pages into 4K chunks, and scales down the ring size accordingly. With
64K pages and 16 descriptors, the ring size mask is 0 and will never
be filled.
32 descriptors is another special case that wedges the RX rings.
Internally, the rings track pages for the head/tail pointers, not page
fragments. So with 32 descriptors, there's only 1 usable page as one
ring slot is kept empty to disambiguate between an empty/full ring.
As a result, the head pointer never advances and the HW stalls after
consuming 16 page fragments.
Fixes: 0cb4c0a137 ("eth: fbnic: Implement Rx queue alloc/start/stop/free")
Signed-off-by: Dimitri Daskalakis <daskald@meta.com>
Link: https://patch.msgid.link/20260401162848.2335350-1-dimitri.daskalakis1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yiming Qian reported :
<quote>
I believe I found a locally triggerable kernel bug in the IPv6 sendmsg
ancillary-data path that can panic the kernel via `skb_under_panic()`
(local DoS).
The core issue is a mismatch between:
- a 16-bit length accumulator (`struct ipv6_txoptions::opt_flen`, type
`__u16`) and
- a pointer to the *last* provided destination-options header (`opt->dst1opt`)
when multiple `IPV6_DSTOPTS` control messages (cmsgs) are provided.
- `include/net/ipv6.h`:
- `struct ipv6_txoptions::opt_flen` is `__u16` (wrap possible).
(lines 291-307, especially 298)
- `net/ipv6/datagram.c:ip6_datagram_send_ctl()`:
- Accepts repeated `IPV6_DSTOPTS` and accumulates into `opt_flen`
without rejecting duplicates. (lines 909-933)
- `net/ipv6/ip6_output.c:__ip6_append_data()`:
- Uses `opt->opt_flen + opt->opt_nflen` to compute header
sizes/headroom decisions. (lines 1448-1466, especially 1463-1465)
- `net/ipv6/ip6_output.c:__ip6_make_skb()`:
- Calls `ipv6_push_frag_opts()` if `opt->opt_flen` is non-zero.
(lines 1930-1934)
- `net/ipv6/exthdrs.c:ipv6_push_frag_opts()` / `ipv6_push_exthdr()`:
- Push size comes from `ipv6_optlen(opt->dst1opt)` (based on the
pointed-to header). (lines 1179-1185 and 1206-1211)
1. `opt_flen` is a 16-bit accumulator:
- `include/net/ipv6.h:298` defines `__u16 opt_flen; /* after fragment hdr */`.
2. `ip6_datagram_send_ctl()` accepts *repeated* `IPV6_DSTOPTS` cmsgs
and increments `opt_flen` each time:
- In `net/ipv6/datagram.c:909-933`, for `IPV6_DSTOPTS`:
- It computes `len = ((hdr->hdrlen + 1) << 3);`
- It checks `CAP_NET_RAW` using `ns_capable(net->user_ns,
CAP_NET_RAW)`. (line 922)
- Then it does:
- `opt->opt_flen += len;` (line 927)
- `opt->dst1opt = hdr;` (line 928)
There is no duplicate rejection here (unlike the legacy
`IPV6_2292DSTOPTS` path which rejects duplicates at
`net/ipv6/datagram.c:901-904`).
If enough large `IPV6_DSTOPTS` cmsgs are provided, `opt_flen` wraps
while `dst1opt` still points to a large (2048-byte)
destination-options header.
In the attached PoC (`poc.c`):
- 32 cmsgs with `hdrlen=255` => `len = (255+1)*8 = 2048`
- 1 cmsg with `hdrlen=0` => `len = 8`
- Total increment: `32*2048 + 8 = 65544`, so `(__u16)opt_flen == 8`
- The last cmsg is 2048 bytes, so `dst1opt` points to a 2048-byte header.
3. The transmit path sizes headers using the wrapped `opt_flen`:
- In `net/ipv6/ip6_output.c:1463-1465`:
- `headersize = sizeof(struct ipv6hdr) + (opt ? opt->opt_flen +
opt->opt_nflen : 0) + ...;`
With wrapped `opt_flen`, `headersize`/headroom decisions underestimate
what will be pushed later.
4. When building the final skb, the actual push length comes from
`dst1opt` and is not limited by wrapped `opt_flen`:
- In `net/ipv6/ip6_output.c:1930-1934`:
- `if (opt->opt_flen) proto = ipv6_push_frag_opts(skb, opt, proto);`
- In `net/ipv6/exthdrs.c:1206-1211`, `ipv6_push_frag_opts()` pushes
`dst1opt` via `ipv6_push_exthdr()`.
- In `net/ipv6/exthdrs.c:1179-1184`, `ipv6_push_exthdr()` does:
- `skb_push(skb, ipv6_optlen(opt));`
- `memcpy(h, opt, ipv6_optlen(opt));`
With insufficient headroom, `skb_push()` underflows and triggers
`skb_under_panic()` -> `BUG()`:
- `net/core/skbuff.c:2669-2675` (`skb_push()` calls `skb_under_panic()`)
- `net/core/skbuff.c:207-214` (`skb_panic()` ends in `BUG()`)
- The `IPV6_DSTOPTS` cmsg path requires `CAP_NET_RAW` in the target
netns user namespace (`ns_capable(net->user_ns, CAP_NET_RAW)`).
- Root (or any task with `CAP_NET_RAW`) can trigger this without user
namespaces.
- An unprivileged `uid=1000` user can trigger this if unprivileged
user namespaces are enabled and it can create a userns+netns to obtain
namespaced `CAP_NET_RAW` (the attached PoC does this).
- Local denial of service: kernel BUG/panic (system crash).
- Reproducible with a small userspace PoC.
</quote>
This patch does not reject duplicated options, as this might break
some user applications.
Instead, it makes sure to adjust opt_flen and opt_nflen to correctly
reflect the size of the current option headers, preventing the overflows
and the potential for panics.
This applies to IPV6_DSTOPTS, IPV6_HOPOPTS, and IPV6_RTHDR.
Specifically:
When a new IPV6_DSTOPTS is processed, the length of the old opt->dst1opt
is subtracted from opt->opt_flen before adding the new length.
When a new IPV6_HOPOPTS is processed, the length of the old opt->dst0opt
is subtracted from opt->opt_nflen.
When a new Routing Header (IPV6_RTHDR or IPV6_2292RTHDR) is processed,
the length of the old opt->srcrt is subtracted from opt->opt_nflen.
In the special case within IPV6_2292RTHDR handling where dst1opt is moved
to dst0opt, the length of the old opt->dst0opt is subtracted from
opt->opt_nflen before the new one is added.
Fixes: 333fad5364 ("[IPV6]: Support several new sockopt / ancillary data in Advanced API (RFC3542).")
Reported-by: Yiming Qian <yimingqian591@gmail.com>
Closes: https://lore.kernel.org/netdev/CAL_bE8JNzawgr5OX5m+3jnQDHry2XxhQT5=jThW1zDPtUikRYA@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260401154721.3740056-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luka Gejak says:
====================
net: hsr: fixes for PRP duplication and VLAN unwind
This series addresses two logic bugs in the HSR/PRP implementation
identified during a protocol audit. These are targeted for the 'net'
tree as they fix potential memory corruption and state inconsistency.
The primary change resolves a race condition in the node merging path by
implementing address-based lock ordering. This ensures that concurrent
mutations of sequence blocks do not lead to state corruption or
deadlocks.
An additional fix corrects asymmetric VLAN error unwinding by
implementing a centralized unwind path on slave errors.
====================
Link: https://patch.msgid.link/20260401092243.52121-1-luka.gejak@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When vlan_vid_add() fails for a secondary slave, the error path calls
vlan_vid_del() on the failing port instead of the peer slave that had
already succeeded. This results in asymmetric VLAN state across the HSR
pair.
Fix this by switching to a centralized unwind path that removes the VID
from any slave device that was already programmed.
Fixes: 1a8a63a530 ("net: hsr: Add VLAN CTAG filter support")
Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260401092243.52121-3-luka.gejak@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During node merging, hsr_handle_sup_frame() walks node_curr->seq_blocks
to update node_real without holding node_curr->seq_out_lock. This
allows concurrent mutations from duplicate registration paths, risking
inconsistent state or XArray/bitmap corruption.
Fix this by locking both nodes' seq_out_lock during the merge.
To prevent ABBA deadlocks, locks are acquired in order of memory
address.
Reviewed-by: Felix Maurer <fmaurer@redhat.com>
Fixes: 415e636751 ("hsr: Implement more robust duplicate discard for PRP")
Signed-off-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260401092243.52121-2-luka.gejak@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `child_ns_mode_locked` field lives in `struct net`, which persists
across vsock module reloads. When the module is unloaded and reloaded,
`vsock_net_init()` resets `mode` and `child_ns_mode` back to their
default values, but does not reset `child_ns_mode_locked`.
The stale lock from the previous module load causes subsequent writes
to `child_ns_mode` to silently fail: `vsock_net_set_child_mode()` sees
the old lock, skips updating the actual value, and returns success
when the requested mode matches the stale lock. The sysctl handler
reports no error, but `child_ns_mode` remains unchanged.
Steps to reproduce:
$ modprobe vsock
$ echo local > /proc/sys/net/vsock/child_ns_mode
$ cat /proc/sys/net/vsock/child_ns_mode
local
$ modprobe -r vsock
$ modprobe vsock
$ echo local > /proc/sys/net/vsock/child_ns_mode
$ cat /proc/sys/net/vsock/child_ns_mode
global <--- expected "local"
Fix this by initializing `child_ns_mode_locked` to 0 (unlocked) in
`vsock_net_init()`, so the write-once mechanism works correctly after
module reload.
Fixes: 102eab95f0 ("vsock: lock down child_ns_mode as write-once")
Reported-by: Jin Liu <jinl@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260401092153.28462-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Regression tests for the shared-block NULL derefs fixed in the previous
two patches:
- fw: attempt to attach an empty fw filter to a shared block and
verify the configuration is rejected with EINVAL.
- flow: create a flow filter on a shared block without a baseclass
and verify the configuration is rejected with EINVAL.
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20260331050217.504278-3-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
flow_change() calls tcf_block_q() and dereferences q->handle to derive
a default baseclass. Shared blocks leave block->q NULL, causing a NULL
deref when a flow filter without a fully qualified baseclass is created
on a shared block.
Check tcf_block_shared() before accessing block->q and return -EINVAL
for shared blocks. This avoids the null-deref shown below:
=======================================================================
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
RIP: 0010:flow_change (net/sched/cls_flow.c:508)
Call Trace:
tc_new_tfilter (net/sched/cls_api.c:2432)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6980)
[...]
=======================================================================
Fixes: 1abf272022 ("net: sched: tcindex, fw, flow: use tcf_block_q helper to get struct Qdisc")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260331050217.504278-2-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The old-method path in fw_classify() calls tcf_block_q() and
dereferences q->handle. Shared blocks leave block->q NULL, causing a
NULL deref when an empty cls_fw filter is attached to a shared block
and a packet with a nonzero major skb mark is classified.
Reject the configuration in fw_change() when the old method (no
TCA_OPTIONS) is used on a shared block, since fw_classify()'s
old-method path needs block->q which is NULL for shared blocks.
The fixed null-ptr-deref calling stack:
KASAN: null-ptr-deref in range [0x0000000000000038-0x000000000000003f]
RIP: 0010:fw_classify (net/sched/cls_fw.c:81)
Call Trace:
tcf_classify (./include/net/tc_wrapper.h:197 net/sched/cls_api.c:1764 net/sched/cls_api.c:1860)
tc_run (net/core/dev.c:4401)
__dev_queue_xmit (net/core/dev.c:4535 net/core/dev.c:4790)
Fixes: 1abf272022 ("net: sched: tcindex, fw, flow: use tcf_block_q helper to get struct Qdisc")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20260331050217.504278-1-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Martin Schiller says:
====================
net/x25: Fix overflow and double free
This patch set includes 2 fixes:
The first removes a potential double free of received skb
The second fixes an overflow when accumulating packets with the more-bit
set.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
====================
Link: https://patch.msgid.link/20260331-x25_fraglen-v4-0-3e69f18464b4@dev.tdt.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When alloc_skb fails in x25_queue_rx_frame it calls kfree_skb(skb) at
line 48 and returns 1 (error).
This error propagates back through the call chain:
x25_queue_rx_frame returns 1
|
v
x25_state3_machine receives the return value 1 and takes the else
branch at line 278, setting queued=0 and returning 0
|
v
x25_process_rx_frame returns queued=0
|
v
x25_backlog_rcv at line 452 sees queued=0 and calls kfree_skb(skb)
again
This would free the same skb twice. Looking at x25_backlog_rcv:
net/x25/x25_in.c:x25_backlog_rcv() {
...
queued = x25_process_rx_frame(sk, skb);
...
if (!queued)
kfree_skb(skb);
}
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://patch.msgid.link/20260331-x25_fraglen-v4-1-3e69f18464b4@dev.tdt.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ASoC: Fixes for v7.0
Another smallish batch of fixes and quirks, these days it's AMD that is
getting all the DMI entries added. We've got one core fix for a missing
list initialisation with auxiliary devices, otherwise it's all fairly
small things.
Michael Chan says:
====================
bnxt_en: Bug fixes
The first patch is a refactor patch needed by the second patch to
fix XDP ring initialization during FW reset. The third patch
fixes an issue related to stats context reservation for RoCE.
====================
Link: https://patch.msgid.link/20260331065138.948205-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During resource reservation, if the L2 driver does not have enough
MSIX vectors to provide to the RoCE driver, it sets the stat ctxs for
ULP also to 0 so that we don't have to reserve it unnecessarily.
However, subsequently the user may reduce L2 rings thereby freeing up
some resources that the L2 driver can now earmark for RoCE. In this
case, the driver should restore the default ULP stat ctxs to make
sure that all RoCE resources are ready for use.
The RoCE driver may fail to initialize in this scenario without this
fix.
Fixes: d630624ebd ("bnxt_en: Utilize ulp client resources if RoCE is not registered")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260331065138.948205-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The original code made the assumption that when we set up the initial
default ring mode, we must be just loading the driver and XDP cannot
be enabled yet. This is not true when the FW goes through a resource
or capability change. Resource reservations will be cancelled and
reinitialized with XDP already enabled. devlink reload with XDP enabled
will also have the same issue. This scenario will cause the ring
arithmetic to be all wrong in the bnxt_init_dflt_ring_mode() path
causing failure:
bnxt_en 0000:a1:00.0 ens2f0np0: bnxt_setup_int_mode err: ffffffea
bnxt_en 0000:a1:00.0 ens2f0np0: bnxt_request_irq err: ffffffea
bnxt_en 0000:a1:00.0 ens2f0np0: nic open fail (rc: ffffffea)
Fix it by properly accounting for XDP in the bnxt_init_dflt_ring_mode()
path by using the refactored helper functions in the previous patch.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Fixes: 228ea8c187 ("bnxt_en: implement devlink dev reload driver_reinit")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260331065138.948205-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid printing the misleading "kernel answers: No data available" devlink
output when querying firmware or pending firmware version fails
(e.g. MLX5 fw state errors / flash failures).
FW can fail on loading the pending flash image and get its version due
to various reasons, examples:
mlxfw: Firmware flash failed: key not applicable, err (7)
mlx5_fw_image_pending: can't read pending fw version while fw state is 1
and the resulting:
$ devlink dev info
kernel answers: No data available
Instead, just report 0 or 0xfff.. versions in case of failure to indicate
a problem, and let other information be shown.
after the fix:
$ devlink dev info
pci/0000:00:06.0:
driver mlx5_core
serial_number xxx...
board.serial_number MT2225300179
versions:
fixed:
fw.psid MT_0000000436
running:
fw.version 22.41.0188
fw 22.41.0188
stored:
fw.version 255.255.65535
fw 255.255.65535
Fixes: 9c86b07e30 ("net/mlx5: Added fw version query command")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260330194015.53585-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__mlx5_lag_dev_add_mdev() may return 0 (success) even when an error
occurs that is handled gracefully. Consequently, the initialization
flow proceeds to call mlx5_ldev_add_debugfs() even when there is no
valid LAG context.
mlx5_ldev_add_debugfs() blindly created the debugfs directory and
attributes. This exposed interfaces (like the members file) that rely on
a valid ldev pointer, leading to potential NULL pointer dereferences if
accessed when ldev is NULL.
Add a check to verify that mlx5_lag_dev(dev) returns a valid pointer
before attempting to create the debugfs entries.
Fixes: 7f46a0b732 ("net/mlx5: Lag, add debugfs to query hardware lag state")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260330194015.53585-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
platform_device_unregister() may still want to use the registered clks
during runtime resume callback.
Note that there is a commit d82d5303c4 ("net: macb: fix use after free
on rmmod") that addressed the similar problem of clk vs platform device
unregistration but just moved the bug to another place.
Save the pointers to clks into local variables for reuse after platform
device is unregistered.
BUG: KASAN: use-after-free in clk_prepare+0x5a/0x60
Read of size 8 at addr ffff888104f85e00 by task modprobe/597
CPU: 2 PID: 597 Comm: modprobe Not tainted 6.1.164+ #114
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xba
print_report+0x17f/0x496
kasan_report+0xd9/0x180
clk_prepare+0x5a/0x60
macb_runtime_resume+0x13d/0x410 [macb]
pm_generic_runtime_resume+0x97/0xd0
__rpm_callback+0xc8/0x4d0
rpm_callback+0xf6/0x230
rpm_resume+0xeeb/0x1a70
__pm_runtime_resume+0xb4/0x170
bus_remove_device+0x2e3/0x4b0
device_del+0x5b3/0xdc0
platform_device_del+0x4e/0x280
platform_device_unregister+0x11/0x50
pci_device_remove+0xae/0x210
device_remove+0xcb/0x180
device_release_driver_internal+0x529/0x770
driver_detach+0xd4/0x1a0
bus_remove_driver+0x135/0x260
driver_unregister+0x72/0xb0
pci_unregister_driver+0x26/0x220
__do_sys_delete_module+0x32e/0x550
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
</TASK>
Allocated by task 519:
kasan_save_stack+0x2c/0x50
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x8e/0x90
__clk_register+0x458/0x2890
clk_hw_register+0x1a/0x60
__clk_hw_register_fixed_rate+0x255/0x410
clk_register_fixed_rate+0x3c/0xa0
macb_probe+0x1d8/0x42e [macb_pci]
local_pci_probe+0xd7/0x190
pci_device_probe+0x252/0x600
really_probe+0x255/0x7f0
__driver_probe_device+0x1ee/0x330
driver_probe_device+0x4c/0x1f0
__driver_attach+0x1df/0x4e0
bus_for_each_dev+0x15d/0x1f0
bus_add_driver+0x486/0x5e0
driver_register+0x23a/0x3d0
do_one_initcall+0xfd/0x4d0
do_init_module+0x18b/0x5a0
load_module+0x5663/0x7950
__do_sys_finit_module+0x101/0x180
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Freed by task 597:
kasan_save_stack+0x2c/0x50
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x106/0x180
__kmem_cache_free+0xbc/0x320
clk_unregister+0x6de/0x8d0
macb_remove+0x73/0xc0 [macb_pci]
pci_device_remove+0xae/0x210
device_remove+0xcb/0x180
device_release_driver_internal+0x529/0x770
driver_detach+0xd4/0x1a0
bus_remove_driver+0x135/0x260
driver_unregister+0x72/0xb0
pci_unregister_driver+0x26/0x220
__do_sys_delete_module+0x32e/0x550
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Fixes: d82d5303c4 ("net: macb: fix use after free on rmmod")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20260330184542.626619-1-pchelkin@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rss_max_key_size in the virtio spec is the maximum key size supported by
the device, not a mandatory size the driver must use. Also the value 40
is a spec minimum, not a spec maximum.
The current code rejects RSS and can fail probe when the device reports a
larger rss_max_key_size than the driver buffer limit. Instead, clamp the
effective key length to min(device rss_max_key_size, NETDEV_RSS_KEY_LEN)
and keep RSS enabled.
This keeps probe working on devices that advertise larger maximum key sizes
while respecting the netdev RSS key buffer size limit.
Fixes: 3f7d9c1964 ("virtio_net: Add hash_key_length check")
Cc: stable@vger.kernel.org
Signed-off-by: Srujana Challa <schalla@marvell.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20260326142344.1171317-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In netem_enqueue(), the packet corruption logic uses
get_random_u32_below(skb_headlen(skb)) to select an index for
modifying skb->data. When an AF_PACKET TX_RING sends fully non-linear
packets over an IPIP tunnel, skb_headlen(skb) evaluates to 0.
Passing 0 to get_random_u32_below() takes the variable-ceil slow path
which returns an unconstrained 32-bit random integer. Using this
unconstrained value as an offset into skb->data results in an
out-of-bounds memory access.
Fix this by verifying skb_headlen(skb) is non-zero before attempting
to corrupt the linear data area. Fully non-linear packets will silently
bypass the corruption logic.
Fixes: c865e5d99e ("[PKT_SCHED] netem: packet corruption option")
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Signed-off-by: Yuan Tan <tanyuan98@outlook.com>
Signed-off-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Yuhang Zheng <z1652074432@gmail.com>
Signed-off-by: Yucheng Lu <kanolyc@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://patch.msgid.link/45435c0935df877853a81e6d06205ac738ec65fa.1774941614.git.kanolyc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net. Note that most
of the bugs fixed here are >5 years old. The large PR is not due to an
increase in regressions.
1) Flowtable hardware offload support in IPv6 can lead to out-of-bounds
when populating the rule action array when combined with double-tagged
vlan. Bump the maximum number of actions from 16 to 24 and check that
such limit is never reached, otherwise bail out. This bugs stems from
the original flowtable hardware offload support.
2) nfnetlink_log does not include the netlink header size of the trailing
NLMSG_DONE message when calculating the skb size. From Florian Westphal.
3) Reject names in xt_cgroup and xt_rateest extensions which are not
nul-terminated. Also from Florian.
4) Use nla_strcmp in ipset lookup by set name, since IPSET_ATTR_NAME and
IPSET_ATTR_NAMEREF are of NLA_STRING type. From Florian Westphal.
5) When unregistering conntrack helpers, pass the helper that is going
away so the expectation cleanup is done accordingly, otherwise UaF is
possible when accessing expectation that refer to the helper that is
gone. From Qi Tang.
6) Zero expectation NAT fields to address leaking kernel memory through
the expectation netlink dump when unset. Also from Qi Tang.
7) Use the master conntrack helper when creating expectations via
ctnetlink, ignore the suggested helper through CTA_EXPECT_HELP_NAME.
This allows to address a possible read of kernel memory off the
expectation object boundary.
8) Fix incorrect release of the hash bucket logic in ipset when the
bucket is empty, leading to shrinking the hash bucket to size 0
which deals to out-of-bound write in next element additions.
From Yifan Wu.
9) Allow the use of x_tables extensions that explicitly declare
NFPROTO_ARP support only. This is to avoid an incorrect hook number
validation due to non-overlapping arp and inet hook number
definitions.
10) Reject immediate NF_QUEUE verdict in nf_tables. The userspace
nft tool always uses the nft_queue expression for queueing.
This ensures this verdict cannot be used for the arp family,
which does supported this.
* tag 'nf-26-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: reject immediate NF_QUEUE verdict
netfilter: x_tables: restrict xt_check_match/xt_check_target extensions for NFPROTO_ARP
netfilter: ipset: drop logically empty buckets in mtype_del
netfilter: ctnetlink: ignore explicit helper on new expectations
netfilter: ctnetlink: zero expect NAT fields when CTA_EXPECT_NAT absent
netfilter: nf_conntrack_helper: pass helper to expect cleanup
netfilter: ipset: use nla_strcmp for IPSET_ATTR_NAME attr
netfilter: x_tables: ensure names are nul-terminated
netfilter: nfnetlink_log: account for netlink header size
netfilter: flowtable: strictly check for maximum number of actions
====================
Link: https://patch.msgid.link/20260401103646.1015423-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
