When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
The DP-HDMI2.1 PCON spec provides way for a source to set PPS
parameters: slice height, slice width and bits_per_pixel, based on
the HDMI2.1 sink capabilities. The DSC encoder of the PCON will
respect these parameters, while preparing the 128 byte PPS.
This patch adds helper functions to calculate these PPS paremeters as
per the HDMI2.1 specification.
v2: Addressed review comments given by Uma Shankar:
-added documentation for functions
-fixed typos and errors
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch SUSPECT_CODE_INDENT, TYPO_SPELLING]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-14-ankit.k.nautiyal@intel.com
This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.
v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-13-ankit.k.nautiyal@intel.com
In this patch enables support for detecting link failures between
PCON and HDMI sink in i915 driver. HDMI link loss indication to
upstream DP source is indicated via IRQ_HPD. This is followed by
reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS).
If the PCON → HDMI 2.1 link status is off; reinitiate frl link
training to recover. Also, report HDMI FRL link error count range for
each individual FRL active lane is indicated by
DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
v2: Checked for dpcd read and write failures and added debug message.
(Uma Shankar)
v3: Rearranged code to re-start FRL link training or fall back to
TMDS mode.
v4: Resused function to check frl which inturn restarts FRL and
fallback to TMDS mode.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-12-ankit.k.nautiyal@intel.com
This patch adds functions to start FRL training for an HDMI2.1 sink,
connected via a PCON as a DP branch device.
This patch also adds a new structure for storing frl training related
data, when FRL training is completed.
v2: As suggested by Uma Shankar:
-renamed couple of variables for better clarity
-tweaked the macros used for correct semantics for true/false
-fixed other styling issues.
v3: Completed the TODO for condition for going to FRL mode.
Modified the condition to determine the required FRL b/w
based only on the Pcon and Sink's max FRL values.
Moved the frl structure initialization to intel_dp_init_connector().
v4: Fixed typo in initialization of frl structure.
v5: Always use FRL if its possible, instead of enabling only for
higher modes as done in v3.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
[Jani: Fixed checkpatch BRACES, CONSTANT_COMPARISON.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-10-ankit.k.nautiyal@intel.com
HDMI2.1 PCON advertises Max FRL bandwidth supported by the PCON.
This patch captures this in dfp cap structure in intel_dp and uses
this to prune connector modes that cannot be supported by the PCON
and FRL bandwidth.
v2: Addressed review comments from Uma Shankar:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
-minor modification of field names and comments.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-9-ankit.k.nautiyal@intel.com
DP Specification for DP2.0 to HDMI2.1 Pcon specifies support for conversion
of colorspace from RGB to YCbCr.
https://groups.vesa.org/wg/DP/document/previewpdf/15651
This patch adds the relavant registers and helper functions to
get the capability and set the color conversion bits for rgb->ycbcr
conversion through PCON.
v2: As suggested in review comments:
-Fixed bug in the check condition in a drm_helper as reported by
Dan Carpenter and Kernel test robot. (Dan Carepenter)
-Modified the color-conversion cap helper function, to accommodate
BT709 and BT2020 colorspace. (Uma Shankar)
-Added spec details for the new cap for color conversion. (Uma Shankar)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-8-ankit.k.nautiyal@intel.com
This patch adds registers for getting DSC encoder capability for
a HDMI2.1 PCon. It also addes helper functions to configure
DSC between the PCON and HDMI2.1 sink.
v2: Corrected offset for DSC encoder bpc and minor changes.
Also added helper functions for getting pcon dsc encoder capabilities
as suggested by Uma Shankar.
v3: Only setting the DSC bits for the Protocol Converter control
registers, avoiding overwritining color conversion bits.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
[Jani: Fixed checkpatch BLOCK_COMMENT_STYLE.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-7-ankit.k.nautiyal@intel.com
There are specific DPCDs defined for detecting link failures between
the PCON and HDMI sink and check the link status. In case of link
failure, PCON will communicate the same using an IRQ_HPD to source.
HDMI sink would have indicated the same to PCON using SCDC interrupt
mechanism. While source can always read final HDMI sink's status using
I2C over AUX, it is easier and faster to read the PCONs already read
HDMI sink status registers.
This patch adds the DPCDs required for link failure detection and
provide a helper function for printing error count/lane which might
help in debugging the link failure issues.
v2: Addressed comments from Uma Shankar:
-rephrased the commit message, as per the code.
-fixed styling issues
-added documentation for the helper function.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-6-ankit.k.nautiyal@intel.com
This patch adds support for configuring a PCON device,
connected as a DP branched device to enable FRL Link training
with a HDMI2.1 + sink.
v2: Fixed typos and addressed other review comments from Uma Shankar.
-changed the commit message for better clarity (Uma Shankar)
-removed unnecessary argument supplied to a drm helper function.
-fixed return value for max frl read from pcon.
v3: Removed DPCD 0x3035 for MAX Sink FRL b/w as per new version of spec.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-5-ankit.k.nautiyal@intel.com
This patch parses HFVSDB fields for DSC1.2 capabilities of an
HDMI2.1 sink. These fields are required by a source to understand the
DSC capability of the sink, to set appropriate PPS parameters,
before transmitting compressed data stream.
v2: Addressed following issues as suggested by Uma Shankar:
-Added a new struct for hdmi dsc cap
-Fixed bugs in macros usage.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-4-ankit.k.nautiyal@intel.com
The HDMI2.1 extends HFVSDB (HDMI Forum Vendor Specific
Data block) to have fields related to newly defined methods of FRL
(Fixed Rate Link) levels, number of lanes supported, DSC Color bit
depth, VRR min/max, FVA (Fast Vactive), ALLM etc.
This patch adds the new HFVSDB fields that are required for
HDMI2.1.
v2: Minor fixes + consistent naming for DPCD register masks
(Uma Shankar)
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch FROM_SIGN_OFF_MISMATCH.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-2-ankit.k.nautiyal@intel.com
For DG1 we have a little of mix up wrt to DDI/port names and indexes.
Bspec refers to the ports as DDIA, DDIB, DDI USBC1 and DDI USBC2
(besides the DDIA, DDIB, DDIC, DDID), but the previous naming is the
most unambiguous one. This means that for any register on Display Engine
we should use the index of A, B, D and E. However in some places this is
not true:
- VBT: uses C and D and have to be mapped to D/E
- IO/Combo: uses C and D, but we already differentiate those when
we created the phy vs port distinction.
This additional mapping for VBT and phy are already covered in previous
patches, so now we can initialize all the DDIs as A, B, D and E.
v2: Squash previous patch enabling just ports A and B since most of the
pumbling code is already merged now
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117084836.2318234-1-lucas.demarchi@intel.com
After having written the entire OA buffer with reports, the HW will
write again at the beginning of the OA buffer. It'll indicate it by
setting the WRAP bits in the OASTATUS register.
When a wrap happens and that at the end of the read vfunc we write the
OASTATUS register back to clear the REPORT_LOST bit, we sometimes see
that the OATAILPTR register is reset to a previous position on Gen8/9
(apparently not the case on Gen11+). This leads the next call to the
read vfunc to process reports we've already read. Because we've marked
those as read by clearing the reason & timestamp dwords, they're
discarded and a "Skipping spurious, invalid OA report" message is
emitted.
The workaround to avoid this OATAILPTR value reset seems to be to set
the wrap bits when writing back OASTATUS.
This change has no impact on userspace, it only avoids a bunch of
DRM_NOTE("Skipping spurious, invalid OA report\n") messages.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: 19f81df285 ("drm/i915/perf: Add OA unit support for Gen 8+")
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117130124.829979-1-lionel.g.landwerlin@intel.com
Skip iterating over bigjoiner slaves, only the master has the state we
care about.
Add the width of the bigjoiner slave to the reconstructed fb.
Hide the bigjoiner slave to userspace, and double the mode on bigjoiner
master.
And last, disable bigjoiner slave from primary if reconstruction fails.
v3:
* Fix the ddi_get_config slave error (Ankit Nautiyal)
v2:
* Unsupported bigjoiner config for initial fb (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* Don't do any hw->uapi state copy for bigjoiner slave
* We still have hw.mode so no need to pass it in
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-7-manasi.d.navare@intel.com
Enabling is done in a special sequence and so should plane updates
be. Ideally the end user never notices the second pipe is used.
This way ideally everything will be tear free, and updates are
really atomic as userspace expects it.
This uses generic modeset_enables() calls like trans port sync
but still has special handling for disable since for slave we
should not disable things like encoder, plls that are not enabled
for slave.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala: Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-6-manasi.d.navare@intel.com
When the clock is higher than the dotclock, try with 2 pipes enabled.
If we can enable 2, then we will go into big joiner mode, and steal
the adjacent crtc.
This only links the crtc's in software, no hardware or plane
programming is done yet. Blobs are also copied from the master's
crtc_state, so it doesn't depend at commit time on the other
crtc_state.
v6:
* Enable dSC for any mode->hdisplay > 5120
v5:
* Remove intel_dp_max_dotclock (Manasi)
v4:
* Fixes in intel_crtc_compute_config (Ville)
v3:
* Manual Rebase (Manasi)
Changes since v1:
- Rename pipe timings to transcoder timings, as they are now different.
Changes since v2:
- Rework bigjoiner checks; always disable slave when recalculating
master. No need to have a separate bigjoiner pass any more.
- Use pipe_mode instead of transcoder_mode, to clean up the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* hskew isn't a thing
* Do the dsc compute if bigjoiner is enabled, not the other way around]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-4-manasi.d.navare@intel.com
Small changes to intel_dp_mode_valid(), allow listing modes that
can only be supported in the bigjoiner configuration, which is
not supported yet.
v13:
* Allow bigjoiner if hdisplay >5120
v12:
* slice_count logic simplify (Ville)
* Fix unnecessary changes in downstream_mode_valid (Ville)
v11:
* Make intel_dp_can_bigjoiner non static
so it can be used in intel_display (Manasi)
v10:
* Simplify logic (Ville)
* Allow bigjoiner on edp (Ville)
v9:
* Restric Bigjoiner on PORT A (Ville)
v8:
* use source dotclock for max dotclock (Manasi)
v7:
* Add can_bigjoiner() helper (Ville)
* Pass bigjoiner to plane_size validation (Ville)
v6:
* Rebase after dp_downstream mode valid changes (Manasi)
v5:
* Increase max plane width to support 8K with bigjoiner (Maarten)
v4:
* Rebase (Manasi)
Changes since v1:
- Disallow bigjoiner on eDP.
Changes since v2:
- Rename intel_dp_downstream_max_dotclock to intel_dp_max_dotclock,
and split off the downstream and source checking to its own function.
(Ville)
v3:
* Rebase (Manasi)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[vsyrjala:
* Keep bigjoiner disabled until everything is ready
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-3-manasi.d.navare@intel.com
The WA specifies that we need to toggle a SDE chicken bit on and then
off as the final step in preparation for s0ix entry.
Bspec: 33450
Bspec: 8402
However, something is happening after we toggle the bit that causes
the WA to be invalidated. This makes dispcnlunit1_cp_xosc_clkreq
active being already in s0ix state i.e SLP_S0 counter incremented.
Tweaking the Wa_14010685332 by setting the bit on suspend and clearing
it on resume turns down the dispcnlunit1_cp_xosc_clkreq.
B.Spec has Documented this tweaked sequence of WA as an alternative.
Let keep this tweaked WA for Gen11 platforms and keep untweaked WA for
other platforms which never observed this issue.
v2 (MattR):
- Change the comment on the workaround to give PCH names rather than
platform names. Although the bspec is setup to list workarounds by
platform, the hardware team has confirmed that the actual issue being
worked around here is something that was introduced back in the
Cannon Lake PCH and carried forward to subsequent PCH's.
- Extend the untweaked version of the workaround to include PCH_CNP as
well. Note that since PCH_CNP is used to represent CMP, this will
apply on CML and some variants of RKL too.
- Cap the untweaked version of the workaround so that it won't apply to
"fake" PCH's (i.e., DG1). The issue we're working around really is
an issue in the PCH itself, not the South Display, so it shouldn't
apply when there isn't a real PCH.
v3:
- use intel_de_rmw(). [Rodrigo]
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110121700.4338-1-anshuman.gupta@intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
EDID can declare the maximum supported bpc up to 16,
and apparently there are displays that do so. Currently
we assume 12 bpc is tha max. Fix the assumption and
toss in a MISSING_CASE() for any other value we don't
expect to see.
This fixes modesets with a display with EDID max bpc > 12.
Previously any modeset would just silently fail on platforms
that didn't otherwise limit this via the max_bpc property.
In particular we don't add the max_bpc property to HDMI
ports on gmch platforms, and thus we would see the raw
max_bpc coming from the EDID.
I suppose we could already adjust this to also allow 16bpc,
but seeing as no current platform supports that there is
little point.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2632
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110210447.27454-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently the DPLL .get_freq() uses pll->state.hw_state which
is not the thing we actually read out (except during driver
load/resume). Outside of that pll->state.hw_state is just the
thing we committed last time around. During state check we
just read the thing into crtc_state->dpll_hw_state, so that
is what we should use for calculating the DPLL output frequency.
I think we used to do this so that the results of the readout
were actually used, but somehow it got changed when the
.get_freq() refactoring happened.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109231239.17002-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Store the relative data rate for planes in the crtc state
so that we don't have to use
intel_atomic_crtc_state_for_each_plane_state() to compute
it even for the planes that are no part of the current state.
Should probably just nuke this stuff entirely an use the normal
plane data rate instead. The two are slightly different since this
relative data rate doesn't factor in the actual pixel clock, so
it's a bit odd thing to even call a "data rate". And since the
watermarks are computed based on the actual data rate anyway
I don't really see what the point of this relative data rate
is. But that's for the future...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106173042.7534-6-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
In order to remove intel_atomic_crtc_state_for_each_plane_state()
from skl_crtc_can_enable_sagv() we can simply precompute whether
each wm level can tolerate the SAGV block time latency or not.
This has the nice side benefit that we remove the duplicated
wm level latency calculation. In fact the copy of that code
we had in skl_crtc_can_enable_sagv() didn't even handle
WaIncreaseLatencyIPCEnabled/Display WA #1141 whereas the copy
in skl_compute_plane_wm() did. So now we just have the one
copy which handles all the w/as.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106173042.7534-5-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
intel_atomic_crtc_state_for_each_plane_state() peeks at the
plane's current state without holding the plane's mutex, trusting
that the crtc's mutex will protect it. In practice that does work
since our planes can't move between pipes, but it sets a bad
example. intel_atomic_crtc_state_for_each_plane_state() also
relies on crtc_state.uapi.plane_mask which may be full of lies
when it comes to the bigjoiner stuff, so soon we can't use it as
is anyway. So best to just get rid of it entirely. Which we can
easily do by switching to the g4x/vlv "raw" watermark approach.
Later on we should even be able to move the "raw" watermark
computation into the normal .plane_check() code, leaving only
the merging/clamping of the final watermarks to the later
stages. But that will require adjusting the ilk+ wm code
similarly as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106173042.7534-3-ville.syrjala@linux.intel.com
