HDCP KSV list readback can choose to use AUX FIFO or
general data register.
For some DisplayPort devices, the KSV list must be read
in 5 byte boundaries.
The original AUX read command does not support these devices.
The AUX command operation control register "REG_AUX_CMD_REQ" uses b[3:0]
as AUX operacion control, and b[7:4] are status bits and read only.
To change KSV read operation uses "CMD_AUX_NATIVE_READ" from using
the data registers to using AUX FIFO.
The extended command "CMD_AUX_GET_KSV_LIST" is added as
"CMD_AUX_NATIVE_READ" with the 0x10 flag which selects AUX FIFO mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-3-e0fdd4844703@ite.corp-partner.google.com
When user enabled HDCP feature, userspace will set HDCP content
to DRM_MODE_CONTENT_PROTECTION_DESIRED. Next, anx7625 will update
HDCP content to DRM_MODE_CONTENT_PROTECTION_ENABLED if down stream
support HDCP feature.
As anx7625 bridge IC will be power down after call .atomic_disable(),
then all HDCP status will be lost on chip. So we should reestablish
HDCP again in .atomic_enable(), and update hdcp content to DESIRE if
current HDCP content is ENABLE in .atomic_disable().
v4:
- Change HDCP content value to DESIRED if HDCP status is ENABLE in bridge
interface .atomic_enable().
v3:
- Move hdcp content value checking from bridge interface
.atomic_check() to .atomic_enable()
v2:
- Add more details in commit message
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Tested-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241219070330.224996-1-xji@analogixsemi.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241219070330.224996-1-xji@analogixsemi.com
Before, every time fdinfo is queried we try to lock all the BOs in the
VM and calculate memory usage from scratch. This works okay if the
fdinfo is rarely read and the VMs don't have a ton of BOs. If either of
these conditions is not true, we get a massive performance hit.
In this new revision, we track the BOs as they change states. This way
when the fdinfo is queried we only need to take the status lock and copy
out the usage stats with minimal impact to the runtime performance. With
this new approach however, we would no longer be able to track active
buffers.
Signed-off-by: Yunxiang Li <Yunxiang.Li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241219151411.1150-6-Yunxiang.Li@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Define how to handle buffers with multiple possible placement so we
don't get incompatible implementations. Callout the resident requirement
for drm-purgeable- explicitly. Remove the requirement for there to be
only drm-memory- or only drm-resident-, it's not what's implemented and
having both is better for back-compat. Also re-order the paragraphs to
flow better.
Signed-off-by: Yunxiang Li <Yunxiang.Li@amd.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241219151411.1150-4-Yunxiang.Li@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Add a optional properties to change LVDS output voltage. This should not
be static as this depends mainly on the connected display voltage
requirement. We have three properties:
- "ti,lvds-termination-ohms", which sets near end termination,
- "ti,lvds-vod-swing-data-microvolt" and
- "ti,lvds-vod-swing-clock-microvolt" which both set LVDS differential
output voltage for data and clock lanes. They are defined as an array
with min and max values. The appropriate bitfield will be set if
selected constraints can be met.
If "ti,lvds-termination-ohms" is not defined the default of 200 Ohm near
end termination will be used. Selecting only one:
"ti,lvds-vod-swing-data-microvolt" or
"ti,lvds-vod-swing-clock-microvolt" can be done, but the output voltage
constraint for only data/clock lanes will be met. Setting both is
recommended.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241216085410.1968634-3-andrej.picej@norik.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241216085410.1968634-3-andrej.picej@norik.com
Add basic DisplayPort audio support.
Support non-live audio playback from two PCMs (DMA channels), and the
volume control in the audio mixer.
As older dtb files may not have the audio DMA channels defined, the
driver will just mark the audio support as disabled if the audio DMA is
missing, and will continue with only display support.
Note: Reset doesn't seem to work (ZYNQMP_DISP_AUD_SOFT_RESET). If we do
a reset, audio playback won't start again even if, afaics, we do set up
all the necessary registers. So, at the moment, resetting the audio
block in dp_dai_hw_free() is commented out.
Tested-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Vishal Sagar <vishal.sagar@amd.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023-xilinx-dp-audio-v4-3-5128881457be@ideasonboard.com
The DP subsystem for ZynqMP supports audio via two channels, and the DP
DMA has dma-engines for those channels. For some reason the DT binding
has not specified those channels, even if the picture included in
xlnx,zynqmp-dpsub.yaml shows "2 x aud" DMAs.
This hasn't caused any issues as the drivers have not supported audio,
and has thus gone unnoticed.
To make it possible to add the audio support to the driver, add the two
audio DMAs to the binding. While strictly speaking this is an ABI break,
there should be no regressions caused by this as we're adding new
entries at the end of the dmas list, and, after the audio support has
been added in "arm64: dts: zynqmp: Add DMA for DP audio", the driver
will treat the audio DMAs as optional to also support the old bindings.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023-xilinx-dp-audio-v4-1-5128881457be@ideasonboard.com
This driver fails to build in random configurations:
drivers/accel/amdxdna/aie2_solver.c: In function 'remove_partition_node':
drivers/accel/amdxdna/aie2_solver.c:121:9: error: implicit declaration of function 'kfree' [-Wimplicit-function-declaration]
121 | kfree(pt_node);
| ^~~~~
drivers/accel/amdxdna/aie2_solver.c: In function 'get_free_partition':
drivers/accel/amdxdna/aie2_solver.c:153:19: error: implicit declaration of function 'kzalloc' [-Wimplicit-function-declaration]
153 | pt_node = kzalloc(sizeof(*pt_node), GFP_KERNEL);
Add the missing include.
Fixes: c88d3325ae ("accel/amdxdna: Add hardware resource solver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241218085902.2684002-1-arnd@kernel.org
Our infoframe setting code currently lacks the ability to clear
infoframes. For some of the infoframes, we only need to replace them,
so if an error occurred when generating a new infoframe we would leave
a stale frame instead of clearing the frame.
However, the Dynamic Range and Mastering (DRM) infoframe should only
be present when displaying HDR content (ie: the HDR_OUTPUT_METADATA blob
is set). If we can't clear infoframes, the stale DRM infoframe will
remain and we can never set the display back to SDR mode.
With this change, we clear infoframes when they can not, or should not,
be generated. This fixes switching to an SDR mode from an HDR one.
Fixes: f378b77227 ("drm/connector: hdmi: Add Infoframes generation")
Signed-off-by: Derek Foreman <derek.foreman@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241202181939.724011-1-derek.foreman@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
After a connector is added to the drm_mode_config::connector_list, it's
visible to any in-kernel users looking up connectors via the above list.
Make sure that the connector is properly initialized before such
look-ups, by initializing the connector with
drm_connector_dynamic_init() - which doesn't add the connector to the
list - and registering it with drm_connector_dynamic_register() - which
adds the connector to the list - after the initialization is complete.
v2: Fix s/drm_connector_dynamic_register()/drm_connector_dynamic_init()
typo in the commit log.
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241211230328.4012496-8-imre.deak@intel.com
