Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now use generic parser and keep things compatible with the
old binding.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now use generic parser. To support the legacy binding without
#pinctrl-cells, add pcs_quirk_missing_pinctrl_cells() and warn about
missing #pinctrl-cells.
Let's also update the documentation for struct pcs_soc_data while at it
as that seems to be out of date.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the BCM2835 datasheet doesn't exactly specify the set-up time for
the GPIO Pull-up/down Clock Registers there was an assumption of 150 cycles
at a clock rate of 1 MHz. During a discussion [1] in the Raspberry Pi forum
it turns out that clock rate refers to the VPU which has a rate of 250 MHz.
So we can reduce the delay to a sensible value and update the comment above.
I tested this optimization with a Raspberry Pi B and a multimeter.
[1] - https://www.raspberrypi.org/forums/viewtopic.php?f=72&t=163352
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Printing the prefix does not provide any additional information. In
addition this makes the output look more consistent with pinctrl-intel.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for pin output control through the pinctrl config:
- support enabling/disabling output on a given pin
- support output level setting (high or low)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Even though the our binding had the assumption that the allwinner,pull and
allwinner,drive properties were optional, the code never took that into
account.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin config get() and set() handlers for pin groups were previously not
implemented by this driver. The pin_config_group_set() is particularly useful
for applying a common config setting to all pins in a specified group with a
single call, without the caller needing to reference each individual pin by
name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During pinmux registration, pinmux table is parsed from DT
for making the pinmux table configuration of pins.
Parse the only those node whose status is not disabled.
This will help on reusing the pin configuration table across
platform and disabling the node by status property if that node
is not needed on given platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers using pinconf_generic_params tables cannot be built with
CONFIG_OF disabled:
drivers/pinctrl/pinctrl-max77620.c:53:44: error: array type has incomplete element type ‘struct pinconf_generic_params’
drivers/pinctrl/pinctrl-max77620.c:55:3: error: field name not in record or union initializer
drivers/pinctrl/pinctrl-max77620.c:55:3: note: (near initialization for ‘max77620_cfg_params’)
drivers/pinctrl/pinctrl-max77620.c:56:3: error: field name not in record or union initializer
This adds a dependency for max77620 to disallow that configuration.
Alternatively, we could rework the pinctrl infrastructure to make the
configuration valid for compile-testing.
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Fixes: 453943dc8f45 ("mfd: Enable compile testing for max77620 and max77686")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is left over from initial experiments with more properties.
It's only used in one place, so let's just get rid of it to make
the code more readable.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>From tony Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Tue, 25 Oct 2016 08:33:34 -0700
Subject: [PATCHv2] pinctrl: single: Drop custom names
We no longer need to allocate custom names as those are dynamically
generated in pinctrl_register_one_pin() if no name is passed to
pinctrl_register_pins().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our bindings are mostly irrelevant now that we have generic pinctrl
bindings that cover exactly the same uses cases.
Add support for the new ones, and obviously keep our old binding support in
order to keep the ABI stable.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Oxford Semiconductor OX820 which is similar as OX810 but
has 50 pins and two registers banks to setup alternate functions.
Add specific pins, groups and functions structures.
Add DT match data to select corresponding support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add refactoring to move ox810se specific functions into specific ops structures
an add support for the dt match data to get soc specific structures.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So far, putting NO_PULL in allwinner,pull was ignored, behaving like if
that property was not there at all.
Obviously, this is not the right thing to do, and in that case, we really
need to just disable the bias.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support more easily the generic pinctrl properties, rework the
pinctrl maps configuration and split it into several sub-functions.
One of the side-effects from that rework is that we only parse the pin
configuration once, since it's going to be common to every pin, instead of
having to parsing once for each pin.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull UBI[FS] fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- Fallout from the merge window, refactoring UBI code introduced some
issues.
- Fixes for an UBIFS readdir bug which can cause getdents() to busy
loop for ever and a bug in the UBIFS xattr code"
* tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs:
ubifs: Abort readdir upon error
UBI: Fix crash in try_recover_peb()
ubi: fix swapped arguments to call to ubi_alloc_aeb
ubifs: Fix xattr_names length in exit paths
ubifs: Rename ubifs_rename2
Pull ext4 fixes from Ted Ts'o:
"A few bug fixes and add some missing KERN_CONT annotations"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add missing KERN_CONT to a few more debugging uses
fscrypto: lock inode while setting encryption policy
ext4: correct endianness conversion in __xattr_check_inode()
fscrypto: make XTS tweak initialization endian-independent
ext4: do not advertise encryption support when disabled
jbd2: fix incorrect unlock on j_list_lock
ext4: super.c: Update logging style using KERN_CONT
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target-pending fixes for v4.9-rc2.
This includes:
- Fix v4.1.y+ reference leak regression with concurrent TMR
ABORT_TASK + session shutdown. (Vaibhav Tandon)
- Enable tcm_fc w/ SCF_USE_CPUID to avoid host exchange timeouts
(Hannes)
- target/user error sense handling fixes. (Andy + MNC + HCH)
- Fix iscsi-target NOP_OUT error path iscsi_cmd descriptor leak
(Varun)
- Two EXTENDED_COPY SCSI status fixes for ESX VAAI (Dinesh Israni +
Nixon Vincent)
- Revert a v4.8 residual overflow change, that breaks sg_inq with
small allocation lengths.
There are a number of folks stress testing the v4.1.y regression fix
in their environments, and more folks doing iser-target I/O stress
testing atop recent v4.x.y code.
There is also one v4.2.y+ RCU conversion regression related to
explicit NodeACL configfs changes, that is still being tracked down"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/tcm_fc: use CPU affinity for responses
target/tcm_fc: Update debugging statements to match libfc usage
target/tcm_fc: return detailed error in ft_sess_create()
target/tcm_fc: print command pointer in debug message
target: fix potential race window in target_sess_cmd_list_waiting()
Revert "target: Fix residual overflow handling in target_complete_cmd_with_length"
target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status code
target: Make EXTENDED_COPY 0xe4 failure return COPY TARGET DEVICE NOT REACHABLE
target: Re-add missing SCF_ACK_KREF assignment in v4.1.y
iscsi-target: fix iscsi cmd leak
iscsi-target: fix spelling mistake "Unsolicitied" -> "Unsolicited"
target/user: Fix comments to not refer to data ring
target/user: Return an error if cmd data size is too large
target/user: Use sense_reason_t in tcmu_queue_cmd_ring
Pull hwmon fixes from Guenter Roeck:
"Couple of hwmon fixes:
Fix a potential ERR_PTR dereference in max31790 driver, and handle
temperature readings below 0 in adm9240 driver"
* tag 'hwmon-for-linus-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max31790) potential ERR_PTR dereference
hwmon: (adm9240) handle temperature readings below 0
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
Pull x86 fixes from Ingo Molnar:
"Three fixes, a hw-enablement and a cross-arch fix/enablement change:
- SGI/UV fix for older platforms
- x32 signal handling fix
- older x86 platform bootup APIC fix
- AVX512-4VNNIW (Neural Network Instructions) and AVX512-4FMAPS
(Multiply Accumulation Single precision instructions) enablement.
- move thread_info back into x86 specific code, to make life easier
for other architectures trying to make use of
CONFIG_THREAD_INFO_IN_TASK_STRUCT=y"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/smp: Don't try to poke disabled/non-existent APIC
sched/core, x86: Make struct thread_info arch specific again
x86/signal: Remove bogus user_64bit_mode() check from sigaction_compat_abi()
x86/platform/UV: Fix support for EFI_OLD_MEMMAP after BIOS callback updates
x86/cpufeature: Add AVX512_4VNNIW and AVX512_4FMAPS features
x86/vmware: Skip timer_irq_works() check on VMware
Pull vmap stack fixes from Ingo Molnar:
"This is fallout from CONFIG_HAVE_ARCH_VMAP_STACK=y on x86: stack
accesses that used to be just somewhat questionable are now totally
buggy.
These changes try to do it without breaking the ABI: the fields are
left there, they are just reporting zero, or reporting narrower
information (the maps file change)"
* 'mm-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm: Change vm_is_stack_for_task() to vm_is_stack_for_current()
fs/proc: Stop trying to report thread stacks
fs/proc: Stop reporting eip and esp in /proc/PID/stat
mm/numa: Remove duplicated include from mprotect.c
Pull irq fixes from Ingo Molnar:
"Mostly irqchip driver fixes, plus a symbol export"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/irq: Export irq_set_parent()
irqchip/gic: Add missing \n to CPU IF adjustment message
irqchip/jcore: Don't show Kconfig menu item for driver
irqchip/eznps: Drop pointless static qualifier in nps400_of_init()
irqchip/gic-v3-its: Fix entry size mask for GITS_BASER
irqchip/gic-v3-its: Fix 64bit GIC{R,ITS}_TYPER accesses
Pull EFI fixes from Ingo Molnar:
"Add Ard Biesheuvel as EFI co-maintainer, plus fix an ARM build bug
with older toolchains"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm: Fix absolute relocation detection for older toolchains
MAINTAINERS: Add myself as EFI maintainer
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)"
* tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore the pkey system calls for now
powerpc: Fix numa topology console print
powerpc/mm: Drop dump_numa_memory_topology()
cxl: Prevent adapter reset if an active context exists
powerpc/boot: Fix boot on systems with uncompressed kernel image
powerpc/mm: Prevent unlikely crash in copro_calculate_slb()
Pull NFS client bugfixes from Anna Schumaker:
"Just two bugfixes this time:
Stable bugfix:
- Fix last_write_offset incorrectly set to page boundary
Other bugfix:
- Fix missing-braces warning"
* tag 'nfs-for-4.9-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
nfs4: fix missing-braces warning
pnfs/blocklayout: fix last_write_offset incorrectly set to page boundary
Pull ACPI fixes from Rafael Wysocki:
"These fix an issue related to system resume in the new WDAT-based
watchdog driver and a return value of a stub function in the ACPI CPPC
framework.
Specifics:
- Update the ACPI WDAT-based watchdog driver to ping the hardware
during system resume to prevent a reset from occurring after the
resume is complete (Mika Westerberg).
- Fix the return value of the pcc_mbox_request_channel() stub for
CONFIG_PCC unset (Hoan Tran)"
* tag 'acpi-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
watchdog: wdat_wdt: Ping the watchdog on resume
mailbox: PCC: Fix return value of pcc_mbox_request_channel()
Pull GIC updates from Marc Zyngier:
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
Pull SCSI fixes from James Bottomley:
"Five small fixes.
Some of these, like the nested spinlock overwriting saved flags and
the Kasan use after free look serious, but they seem not to have been
picked up in testing or seen in the field.
The biggest user visible issue is probably the wrong device handler
for Clariion, which means that alua doesn't bind to the array like it
should"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: Fix async error WARN_ON
scsi: zfcp: spin_lock_irqsave() is not nestable
scsi: Remove one useless stack variable
scsi: Fix use-after-free
scsi: Replace wrong device handler name for CLARiiON arrays
Pull block fixes from Jens Axboe:
"A set of fixes that missed the merge window, mostly due to me being
away around that time.
Nothing major here, a mix of nvme cleanups and fixes, and one fix for
the badblocks handling"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: use symbolic constants for CNS values
nvme: use symbolic constants for CNS values
nvme.h: add an enum for cns values
nvme.h: don't use uuid_be
nvme.h: resync with nvme-cli
nvme: Add tertiary number to NVME_VS
nvme : Add sysfs entry for NVMe CMBs when appropriate
nvme: don't schedule multiple resets
nvme: Delete created IO queues on reset
nvme: Stop probing a removed device
badblocks: fix overlapping check for clearing
Pull PCI fixes from Bjorn Helgaas:
"This includes:
- Fix for a Layerscape driver issue that causes a use-before-set
crash
- Maintainer update for the Synopsis prototyping device driver"
* tag 'pci-v4.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
When used with a compiler that doesn't implement "asm goto"
(such as the AArch64 port of GCC 4.8), jump labels generate a
memory access to find out about the value of the key (instead
of just patching the code). The key itself is likely to be
stored in the BSS.
This is perfectly fine, except that we don't map the BSS at HYP,
leading to an exploding kernel at the first access. The obvious
fix is simply to map the BSS there (which should have been done
a long while ago, but hey...).
Reported-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The WnR bit in the HSR/ESR_EL2 indicates whether a data abort was
generated by a read or a write instruction. For stage 2 data aborts
generated by a stage 1 translation table walk (i.e. the actual page
table access faults at EL2), the WnR bit therefore reports whether the
instruction generating the walk was a load or a store, *not* whether the
page table walker was reading or writing the entry.
For page tables marked as read-only at stage 2 (e.g. due to KSM merging
them with the tables from another guest), this could result in livelock,
where a page table walk generated by a load instruction attempts to
set the access flag in the stage 1 descriptor, but fails to trigger
CoW in the host since only a read fault is reported.
This patch modifies the arm64 kvm_vcpu_dabt_iswrite function to
take into account stage 2 faults in stage 1 walks. Since DBM cannot be
disabled at EL2 for CPUs that implement it, we assume that these faults
are always causes by writes, avoiding the livelock situation at the
expense of occasional, spurious CoWs.
We could, in theory, do a bit better by checking the guest TCR
configuration and inspecting the page table to see why the PTE faulted.
However, I doubt this is measurable in practice, and the threat of
livelock is real.
Cc: <stable@vger.kernel.org>
Cc: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull more drm fixes from Dave Airlie:
"Mainly some vmwgfx fixes, but also some fixes for armada, etnaviv and
fsl-dcu"
* tag 'drm-fixes-for-v4.9-rc2-part2' of git://people.freedesktop.org/~airlied/linux:
drm/fsl-dcu: enable pixel clock when enabling CRTC
drm/fsl-dcu: do not transfer registers in mode_set_nofb
drm/fsl-dcu: do not transfer registers on plane init
drm/fsl-dcu: enable TCON bypass mode by default
drm/vmwgfx: Adjust checks for null pointers in 13 functions
drm/vmwgfx: Use memdup_user() rather than duplicating its implementation
drm/vmwgfx: Use kmalloc_array() in vmw_surface_define_ioctl()
drm/vmwgfx: Avoid validating views on view destruction
drm/vmwgfx: Limit the user-space command buffer size
drm/vmwgfx: Remove a leftover debug printout
drm/vmwgfx: Allow resource relocations on byte boundaries
drm/vmwgfx: Enable SVGA_3D_CMD_DX_TRANSFER_FROM_BUFFER command
drm/vmwgfx: Remove call to reservation_object_test_signaled_rcu before wait
drm/vmwgfx: Replace numeric parameter like 0444 with macro
drm/etnaviv: block 64K of address space behind each cmdstream
drm/etnaviv: ensure write caches are flushed at end of user cmdstream
drm/armada: fix clock counts
Although I am leaving Synopsys, I would like to keep working with the linux
kernel community and help in what you might find useful. For that I am
sending this patch to change my contact e-mail.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
