If hardware is already transmitting, it can start handling the
descriptor being written to immediately after it observes updated DT
field, before the queue is kicked by a write to GWTRC.
If the start_xmit() execution is preempted at unfortunate moment, this
transmission can complete, and interrupt handled, before gq->cur gets
updated. With the current implementation of completion, this will cause
the last entry not completed.
Fix that by changing completion loop to check DT values directly, instead
of depending on gq->cur.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-3-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sending frame split into multiple descriptors, hardware processes
descriptors one by one, including writing back DT values. The first
descriptor could be already marked as completed when processing of
next descriptors for the same frame is still in progress.
Although only the last descriptor is configured to generate interrupt,
completion of the first descriptor could be noticed by the driver when
handling interrupt for the previous frame.
Currently, driver stores skb in the entry that corresponds to the first
descriptor. This results into skb could be unmapped and freed when
hardware did not complete the send yet. This opens a window for
corrupting the data being sent.
Fix this by saving skb in the entry that corresponds to the last
descriptor used to send the frame.
Fixes: d2c96b9d5f ("net: rswitch: Add jumbo frames handling for TX")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-2-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
A small set of fixes:
- avoid CSA warnings during link removal
(by changing link bitmap after remove)
- fix # of spatial streams initialisation
- fix queues getting stuck in some CSA cases
and resume failures
- fix interface address when switching monitor mode
- fix MBSS change flags 32-bit stack corruption
- more UBSAN __counted_by "fixes" ...
- fix link ID netlink validation
* tag 'wireless-2024-12-10' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: sme: init n_channels before channels[] access
wifi: mac80211: fix station NSS capability initialization order
wifi: mac80211: fix vif addr when switching from monitor to station
wifi: mac80211: fix a queue stall in certain cases of CSA
wifi: mac80211: wake the queues in case of failure in resume
wifi: cfg80211: clear link ID from bitmap during link delete after clean up
wifi: mac80211: init cnt before accessing elem in ieee80211_copy_mbssid_beacon
wifi: mac80211: fix mbss changed flags corruption on 32 bit systems
wifi: nl80211: fix NL80211_ATTR_MLO_LINK_ID off-by-one
====================
Link: https://patch.msgid.link/20241210130145.28618-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net.ipv4.nexthop_compat_mode was added when nexthop objects were added to
provide the view of nexthop objects through the usual lens of the route
UAPI. As nexthop objects evolved, the information provided through this
lens became incomplete. For example, details of resilient nexthop groups
are obviously omitted.
Now that 16-bit nexthop group weights are a thing, the 8-bit UAPI cannot
convey the >8-bit weight accurately. Instead of inventing workarounds for
an obsolete interface, just document the expectations of inaccuracy.
Fixes: b72a6a7ab9 ("net: nexthop: Increase weight to u16")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/b575e32399ccacd09079b2a218255164535123bd.1733740749.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 5760X (P7) chip's HW GRO/LRO interface is very similar to that of
the previous generation (5750X or P5). However, the aggregation ID
fields in the completion structures on P7 have been redefined from
16 bits to 12 bits. The freed up 4 bits are redefined for part of the
metadata such as the VLAN ID. The aggregation ID mask was not modified
when adding support for P7 chips. Including the extra 4 bits for the
aggregation ID can potentially cause the driver to store or fetch the
packet header of GRO/LRO packets in the wrong TPA buffer. It may hit
the BUG() condition in __skb_pull() because the SKB contains no valid
packet header:
kernel BUG at include/linux/skbuff.h:2766!
Oops: invalid opcode: 0000 1 PREEMPT SMP NOPTI
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Kdump: loaded Tainted: G OE 6.12.0-rc2+ #7
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: Dell Inc. PowerEdge R760/0VRV9X, BIOS 1.0.1 12/27/2022
RIP: 0010:eth_type_trans+0xda/0x140
Code: 80 00 00 00 eb c1 8b 47 70 2b 47 74 48 8b 97 d0 00 00 00 83 f8 01 7e 1b 48 85 d2 74 06 66 83 3a ff 74 09 b8 00 04 00 00 eb a5 <0f> 0b b8 00 01 00 00 eb 9c 48 85 ff 74 eb 31 f6 b9 02 00 00 00 48
RSP: 0018:ff615003803fcc28 EFLAGS: 00010283
RAX: 00000000000022d2 RBX: 0000000000000003 RCX: ff2e8c25da334040
RDX: 0000000000000040 RSI: ff2e8c25c1ce8000 RDI: ff2e8c25869f9000
RBP: ff2e8c258c31c000 R08: ff2e8c25da334000 R09: 0000000000000001
R10: ff2e8c25da3342c0 R11: ff2e8c25c1ce89c0 R12: ff2e8c258e0990b0
R13: ff2e8c25bb120000 R14: ff2e8c25c1ce89c0 R15: ff2e8c25869f9000
FS: 0000000000000000(0000) GS:ff2e8c34be300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f05317e4c8 CR3: 000000108bac6006 CR4: 0000000000773ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x33/0x90
? do_trap+0xd9/0x100
? eth_type_trans+0xda/0x140
? do_error_trap+0x65/0x80
? eth_type_trans+0xda/0x140
? exc_invalid_op+0x4e/0x70
? eth_type_trans+0xda/0x140
? asm_exc_invalid_op+0x16/0x20
? eth_type_trans+0xda/0x140
bnxt_tpa_end+0x10b/0x6b0 [bnxt_en]
? bnxt_tpa_start+0x195/0x320 [bnxt_en]
bnxt_rx_pkt+0x902/0xd90 [bnxt_en]
? __bnxt_tx_int.constprop.0+0x89/0x300 [bnxt_en]
? kmem_cache_free+0x343/0x440
? __bnxt_tx_int.constprop.0+0x24f/0x300 [bnxt_en]
__bnxt_poll_work+0x193/0x370 [bnxt_en]
bnxt_poll_p5+0x9a/0x300 [bnxt_en]
? try_to_wake_up+0x209/0x670
__napi_poll+0x29/0x1b0
Fix it by redefining the aggregation ID mask for P5_PLUS chips to be
12 bits. This will work because the maximum aggregation ID is less
than 4096 on all P5_PLUS chips.
Fixes: 13d2d3d381 ("bnxt_en: Add new P7 hardware interface definitions")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241209015448.1937766-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the blamed commit below, udp_rehash() is supposed to be called
with both local and remote addresses set.
Currently that is already the case for IPv6 sockets, but for IPv4 the
destination address is updated after rehashing.
Address the issue moving the destination address and port initialization
before rehashing.
Fixes: 1b29a730ef ("ipv6/udp: Add 4-tuple hash for connected socket")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/4761e466ab9f7542c68cdc95f248987d127044d2.1733499715.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
virtnet_sq_bind_xsk_pool() flushes tx skbs and then resets tx queue, so
DQL counters need to be reset when flushing has actually occurred, Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_resize()
to handle this.
Fixes: 21a4e3ce6d ("virtio_net: xsk: bind/unbind xsk for tx")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When virtqueue_reset() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when it really occurs.
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
virtnet_tx_resize() flushes remaining tx skbs, requiring DQL counters to
be reset when flushing has actually occurred. Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_reset() to
handle this.
Fixes: c8bd1f7f3e ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When virtqueue_resize() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when the recycle really occurs.
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While not harmful, using vq2rxq where it's always sq appears odd.
Replace it with the more appropriate vq2txq for clarity and correctness.
Fixes: 89f86675cb ("virtio_net: xsk: tx: support xmit xsk buffer")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When virtnet_close is followed by virtnet_open, some TX completions can
possibly remain unconsumed, until they are finally processed during the
first NAPI poll after the netdev_tx_reset_queue(), resulting in a crash
[1]. Commit b96ed2c97c ("virtio_net: move netdev_tx_reset_queue() call
before RX napi enable") was not sufficient to eliminate all BQL crash
cases for virtio-net.
This issue can be reproduced with the latest net-next master by running:
`while :; do ip l set DEV down; ip l set DEV up; done` under heavy network
TX load from inside the machine.
netdev_tx_reset_queue() can actually be dropped from virtnet_open path;
the device is not stopped in any case. For BQL core part, it's just like
traffic nearly ceases to exist for some period. For stall detector added
to BQL, even if virtnet_close could somehow lead to some TX completions
delayed for long, followed by virtnet_open, we can just take it as stall
as mentioned in commit 6025b9135f ("net: dqs: add NIC stall detector
based on BQL"). Note also that users can still reset stall_max via sysfs.
So, drop netdev_tx_reset_queue() from virtnet_enable_queue_pair(). This
eliminates the BQL crashes. As a result, netdev_tx_reset_queue() is now
explicitly required in freeze/restore path. This patch adds it to
immediately after free_unused_bufs(), following the rule of thumb:
netdev_tx_reset_queue() should follow any SKB freeing not followed by
netdev_tx_completed_queue(). This seems the most consistent and
streamlined approach, and now netdev_tx_reset_queue() runs whenever
free_unused_bufs() is done.
[1]:
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:99!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 UID: 0 PID: 1598 Comm: ip Tainted: G N 6.12.0net-next_main+ #2
Tainted: [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), \
BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:dql_completed+0x26b/0x290
Code: b7 c2 49 89 e9 44 89 da 89 c6 4c 89 d7 e8 ed 17 47 00 58 65 ff 0d
4d 27 90 7e 0f 85 fd fe ff ff e8 ea 53 8d ff e9 f3 fe ff ff <0f> 0b 01
d2 44 89 d1 29 d1 ba 00 00 00 00 0f 48 ca e9 28 ff ff ff
RSP: 0018:ffffc900002b0d08 EFLAGS: 00010297
RAX: 0000000000000000 RBX: ffff888102398c80 RCX: 0000000080190009
RDX: 0000000000000000 RSI: 000000000000006a RDI: 0000000000000000
RBP: ffff888102398c00 R08: 0000000000000000 R09: 0000000000000000
R10: 00000000000000ca R11: 0000000000015681 R12: 0000000000000001
R13: ffffc900002b0d68 R14: ffff88811115e000 R15: ffff8881107aca40
FS: 00007f41ded69500(0000) GS:ffff888667dc0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556ccc2dc1a0 CR3: 0000000104fd8003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x32/0x80
? do_trap+0xd9/0x100
? dql_completed+0x26b/0x290
? dql_completed+0x26b/0x290
? do_error_trap+0x6d/0xb0
? dql_completed+0x26b/0x290
? exc_invalid_op+0x4c/0x60
? dql_completed+0x26b/0x290
? asm_exc_invalid_op+0x16/0x20
? dql_completed+0x26b/0x290
__free_old_xmit+0xff/0x170 [virtio_net]
free_old_xmit+0x54/0xc0 [virtio_net]
virtnet_poll+0xf4/0xe30 [virtio_net]
? __update_load_avg_cfs_rq+0x264/0x2d0
? update_curr+0x35/0x260
? reweight_entity+0x1be/0x260
__napi_poll.constprop.0+0x28/0x1c0
net_rx_action+0x329/0x420
? enqueue_hrtimer+0x35/0x90
? trace_hardirqs_on+0x1d/0x80
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? sched_clock_cpu+0xd/0x1a0
handle_softirqs+0x138/0x3e0
do_softirq.part.0+0x89/0xc0
</IRQ>
<TASK>
__local_bh_enable_ip+0xa7/0xb0
virtnet_open+0xc8/0x310 [virtio_net]
__dev_open+0xfa/0x1b0
__dev_change_flags+0x1de/0x250
dev_change_flags+0x22/0x60
do_setlink.isra.0+0x2df/0x10b0
? rtnetlink_rcv_msg+0x34f/0x3f0
? netlink_rcv_skb+0x54/0x100
? netlink_unicast+0x23e/0x390
? netlink_sendmsg+0x21e/0x490
? ____sys_sendmsg+0x31b/0x350
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? __nla_validate_parse+0x5f/0xee0
? __pfx___probestub_irq_enable+0x3/0x10
? __create_object+0x5e/0x90
? security_capable+0x3b/0x70
rtnl_newlink+0x784/0xaf0
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? stack_depot_save_flags+0x24/0x6d0
? __pfx_rtnl_newlink+0x10/0x10
rtnetlink_rcv_msg+0x34f/0x3f0
? do_syscall_64+0x6c/0x180
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x54/0x100
netlink_unicast+0x23e/0x390
netlink_sendmsg+0x21e/0x490
____sys_sendmsg+0x31b/0x350
? copy_msghdr_from_user+0x6d/0xa0
___sys_sendmsg+0x86/0xd0
? __pte_offset_map+0x17/0x160
? preempt_count_add+0x69/0xa0
? __call_rcu_common.constprop.0+0x147/0x610
? preempt_count_add+0x69/0xa0
? preempt_count_add+0x69/0xa0
? _raw_spin_trylock+0x13/0x60
? trace_hardirqs_on+0x1d/0x80
__sys_sendmsg+0x66/0xc0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f41defe5b34
Code: 15 e1 12 0f 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00
f3 0f 1e fa 80 3d 35 95 0f 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55
RSP: 002b:00007ffe5336ecc8 EFLAGS: 00000202 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f41defe5b34
RDX: 0000000000000000 RSI: 00007ffe5336ed30 RDI: 0000000000000003
RBP: 00007ffe5336eda0 R08: 0000000000000010 R09: 0000000000000001
R10: 00007ffe5336f6f9 R11: 0000000000000202 R12: 0000000000000003
R13: 0000000067452259 R14: 0000556ccc28b040 R15: 0000000000000000
</TASK>
[...]
Fixes: c8bd1f7f3e ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
[ pabeni: trimmed possibly troublesome separator ]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t4_set_vf_mac_acl() uses pf to set mac addr, but t4vf_get_vf_mac_acl()
uses port number to get mac addr, this leads to error when an attempt
to set MAC address on VF's of PF2 and PF3.
This patch fixes the issue by using port number to set mac address.
Fixes: e0cdac65ba ("cxgb4vf: configure ports accessible by the VF")
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241206062014.49414-1-anumula@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On port initialization, we configure the maximum frame length accepted
by the receive module associated with the port. This value is currently
written to the MAX_LEN field of the DEV10G_MAC_ENA_CFG register, when in
fact, it should be written to the DEV10G_MAC_MAXLEN_CFG register. Fix
this.
Fixes: 946e7fd505 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing port mirroring, the physical port to send the frame to, is
written to the FRMC_PORT_VAL field of the QFWD_FRAME_COPY_CFG register.
This field is 7 bits wide on sparx5 and 6 bits wide on lan969x, and has
a default value of 65 and 30, respectively (the number of front ports).
On mirror deletion, we set the default value of the monitor port to
65 for this field, in case no more ports exists for the mirror. Needless
to say, this will not fit the 6 bits on lan969x.
Fix this by correctly using the n_ports constant instead.
Fixes: 3f9e46347a ("net: sparx5: use SPX5_CONST for constants which already have a symbol")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FDMA handler is responsible for scheduling a NAPI poll, which will
eventually fetch RX packets from the FDMA queue. Currently, the FDMA
handler is run in a threaded context. For some reason, this kills
performance. Admittedly, I did not do a thorough investigation to see
exactly what causes the issue, however, I noticed that in the other
driver utilizing the same FDMA engine, we run the FDMA handler in hard
IRQ context.
Fix this performance issue, by running the FDMA handler in hard IRQ
context, not deferring any work to a thread.
Prior to this change, the RX UDP performance was:
Interval Transfer Bitrate Jitter
0.00-10.20 sec 44.6 MBytes 36.7 Mbits/sec 0.027 ms
After this change, the rx UDP performance is:
Interval Transfer Bitrate Jitter
0.00-9.12 sec 1.01 GBytes 953 Mbits/sec 0.020 ms
Fixes: 10615907e9 ("net: sparx5: switchdev: adding frame DMA functionality")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depmod reports a cyclic dependency between modules sparx5-switch.ko and
lan969x-switch.ko:
depmod: ERROR: Cycle detected: lan969x_switch -> sparx5_switch -> lan969x_switch
depmod: ERROR: Found 2 modules in dependency cycles!
make[2]: *** [scripts/Makefile.modinst:132: depmod] Error 1
make: *** [Makefile:224: __sub-make] Error 2
This makes sense, as they both require symbols from each other.
Fix this by compiling lan969x support into the sparx5-switch.ko module.
In order to do this, in a sensible way, we move the lan969x/ dir into
the sparx5/ dir and do some code cleanup of code that is no longer
required.
After this patch, depmod will no longer complain, as lan969x support is
compiled into the sparx5-swicth.ko module, and can no longer be compiled
as a standalone module.
Fixes: 98a0111960 ("net: sparx5: add compatible string for lan969x")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Ocelot PTP fixes
This is another attempt at "net: mscc: ocelot: be resilient to loss of
PTP packets during transmission".
https://lore.kernel.org/netdev/20241203164755.16115-1-vladimir.oltean@nxp.com/
The central change is in patch 4/5. It recovers a port from a very
reproducible condition where previously, it would become unable to take
any hardware TX timestamp.
Then we have patches 1/5 and 5/5 which are extra bug fixes.
Patches 2/5 and 3/5 are logical changes split out of the monolithic
patch previously submitted as v1, so that patch 4/5 is hopefully easier
to follow.
====================
Link: https://patch.msgid.link/20241205145519.1236778-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An unsupported RX filter will leave the port with TX timestamping still
applied as per the new request, rather than the old setting. When
parsing the tx_type, don't apply it just yet, but delay that until after
we've parsed the rx_filter as well (and potentially returned -ERANGE for
that).
Similarly, copy_to_user() may fail, which is a rare occurrence, but
should still be treated by unwinding what was done.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf53766 ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_txtstamp() is a threaded IRQ handler, requested explicitly as
such by both ocelot_ptp_rdy_irq_handler() and vsc9959_irq_handler().
As such, it runs with IRQs enabled, and not in hardirq context. Thus,
ocelot_port_add_txtstamp_skb() has no reason to turn off IRQs, it cannot
be preempted by ocelot_get_txtstamp(). For the same reason,
dev_kfree_skb_any_reason() will always evaluate as kfree_skb_reason() in
this calling context, so just simplify the dev_kfree_skb_any() call to
kfree_skb().
Also, ocelot_port_txtstamp_request() runs from NET_TX softirq context,
not with hardirqs enabled. Thus, ocelot_get_txtstamp() which shares the
ocelot_port->tx_skbs.lock lock with it, has no reason to disable hardirqs.
This is part of a larger rework of the TX timestamping procedure.
A logical subportion of the rework has been split into a separate
change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This condition, theoretically impossible to trigger, is not really
handled well. By "continuing", we are skipping the write to SYS_PTP_NXT
which advances the timestamp FIFO to the next entry. So we are reading
the same FIFO entry all over again, printing stack traces and eventually
killing the kernel.
No real problem has been observed here. This is part of a larger rework
of the timestamp IRQ procedure, with this logical change split out into
a patch of its own. We will need to "goto next_ts" for other conditions
as well.
Fixes: 9fde506e0c ("net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 66600fac7a ("net: stmmac: TSO: Fix unbalanced DMA map/unmap
for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s
members to be later in stmmac_tso_xmit().
The buf (dma cookie) and len stored in this structure are passed to
dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that
the dma cookie passed to dma_unmap_single() is the same as the value
returned from dma_map_single(). However, by moving the assignment
later, this is not the case when priv->dma_cap.addr64 > 32 as "des"
is offset by proto_hdr_len.
This causes problems such as:
dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed
and with DMA_API_DEBUG enabled:
DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes]
Fix this by maintaining "des" as the original DMA cookie, and use
tso_des to pass the offset DMA cookie to stmmac_tso_allocator().
Full details of the crashes can be found at:
https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Fixes: 66600fac7a ("net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/E1tJXcx-006N4Z-PC@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: Bug fixes
There are 2 bug fixes in this series. This first one fixes the issue
of setting the gso_type incorrectly for HW GRO packets on 5750X (Thor)
chips. This can cause HW GRO packets to be dropped by the stack if
they are re-segmented. The second one fixes a potential division by
zero crash when dumping FW log coredump.
====================
Link: https://patch.msgid.link/20241204215918.1692597-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing code is using RSS profile to determine IPV4/IPV6 GSO type
on all chips older than 5760X. This won't work on 5750X chips that may
be using modified RSS profiles. This commit from 2018 has updated the
driver to not use RSS profile for HW GRO packets on newer chips:
50f011b63d ("bnxt_en: Update RSS setup and GRO-HW logic according to the latest spec.")
However, a recent commit to add support for the newest 5760X chip broke
the logic. If the GRO packet needs to be re-segmented by the stack, the
wrong GSO type will cause the packet to be dropped.
Fix it to only use RSS profile to determine GSO type on the oldest
5730X/5740X chips which cannot use the new method and is safe to use the
RSS profiles.
Also fix the L3/L4 hash type for RX packets by not using the RSS
profile for the same reason. Use the ITYPE field in the RX completion
to determine L3/L4 hash types correctly.
Fixes: a7445d6980 ("bnxt_en: Add support for new RX and TPA_START completion types for P7")
Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20241204215918.1692597-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
selftests: mlxsw: Add few fixes for sharedbuffer test
Danielle Ratson writes:
Currently, the sharedbuffer test fails sometimes because it is reading a
maximum occupancy that is larger than expected on some different cases.
This is happening because the test assumes that the packet it is sending
is the only packet being passed to the device.
In addition, some duplications on one hand, and redundant test cases on
the other hand, were found in the test.
Add egress filters on h1 and h2 that will guarantee that the packets in
the buffer are sent in the test, and remove the redundant test cases.
====================
Link: https://patch.msgid.link/cover.1733414773.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the __counted_by annocation in cfg80211_scan_request struct,
the "n_channels" struct member must be set before accessing the
"channels" array. Failing to do so will trigger a runtime warning
when enabling CONFIG_UBSAN_BOUNDS and CONFIG_FORTIFY_SOURCE.
Fixes: e3eac9f32e ("wifi: cfg80211: Annotate struct cfg80211_scan_request with __counted_by")
Signed-off-by: Haoyu Li <lihaoyu499@gmail.com>
Link: https://patch.msgid.link/20241203152049.348806-1-lihaoyu499@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dr_domain_add_vport_cap() function generally returns NULL on error
but sometimes we want it to return ERR_PTR(-EBUSY) so the caller can
retry. The problem here is that "ret" can be either -EBUSY or -ENOMEM
and if it's and -ENOMEM then the error pointer is propogated back and
eventually dereferenced in dr_ste_v0_build_src_gvmi_qpn_tag().
Fixes: 11a45def2e ("net/mlx5: DR, Add support for SF vports")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/07477254-e179-43e2-b1b3-3b9db4674195@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Paolo Abeni:
"Including fixes from can and netfilter.
Current release - regressions:
- rtnetlink: fix double call of rtnl_link_get_net_ifla()
- tcp: populate XPS related fields of timewait sockets
- ethtool: fix access to uninitialized fields in set RXNFC command
- selinux: use sk_to_full_sk() in selinux_ip_output()
Current release - new code bugs:
- net: make napi_hash_lock irq safe
- eth:
- bnxt_en: support header page pool in queue API
- ice: fix NULL pointer dereference in switchdev
Previous releases - regressions:
- core: fix icmp host relookup triggering ip_rt_bug
- ipv6:
- avoid possible NULL deref in modify_prefix_route()
- release expired exception dst cached in socket
- smc: fix LGR and link use-after-free issue
- hsr: avoid potential out-of-bound access in fill_frame_info()
- can: hi311x: fix potential use-after-free
- eth: ice: fix VLAN pruning in switchdev mode
Previous releases - always broken:
- netfilter:
- ipset: hold module reference while requesting a module
- nft_inner: incorrect percpu area handling under softirq
- can: j1939: fix skb reference counting
- eth:
- mlxsw: use correct key block on Spectrum-4
- mlx5: fix memory leak in mlx5hws_definer_calc_layout"
* tag 'net-6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
net :mana :Request a V2 response version for MANA_QUERY_GF_STAT
net: avoid potential UAF in default_operstate()
vsock/test: verify socket options after setting them
vsock/test: fix parameter types in SO_VM_SOCKETS_* calls
vsock/test: fix failures due to wrong SO_RCVLOWAT parameter
net/mlx5e: Remove workaround to avoid syndrome for internal port
net/mlx5e: SD, Use correct mdev to build channel param
net/mlx5: E-Switch, Fix switching to switchdev mode in MPV
net/mlx5: E-Switch, Fix switching to switchdev mode with IB device disabled
net/mlx5: HWS: Properly set bwc queue locks lock classes
net/mlx5: HWS: Fix memory leak in mlx5hws_definer_calc_layout
bnxt_en: handle tpa_info in queue API implementation
bnxt_en: refactor bnxt_alloc_rx_rings() to call bnxt_alloc_rx_agg_bmap()
bnxt_en: refactor tpa_info alloc/free into helpers
geneve: do not assume mac header is set in geneve_xmit_skb()
mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4
ethtool: Fix wrong mod state in case of verbose and no_mask bitset
ipmr: tune the ipmr_can_free_table() checks.
netfilter: nft_set_hash: skip duplicated elements pending gc run
netfilter: ipset: Hold module reference while requesting a module
...
Pull tracing fixes from Steven Rostedt:
- Fix trace histogram sort function cmp_entries_dup()
The sort function cmp_entries_dup() returns either 1 or 0, and not -1
if parameter "a" is less than "b" by memcmp().
- Fix archs that call trace_hardirqs_off() without RCU watching
Both x86 and arm64 no longer call any tracepoints with RCU not
watching. It was assumed that it was safe to get rid of
trace_*_rcuidle() version of the tracepoint calls. This was needed to
get rid of the SRCU protection and be able to implement features like
faultable traceponits and add rust tracepoints.
Unfortunately, there were a few architectures that still relied on
that logic. There's only one file that has tracepoints that are
called without RCU watching. Add macro logic around the tracepoints
for architectures that do not have CONFIG_ARCH_WANTS_NO_INSTR defined
will check if the code is in the idle path (the only place RCU isn't
watching), and enable RCU around calling the tracepoint, but only do
it if the tracepoint is enabled.
* tag 'trace-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix archs that still call tracepoints without RCU watching
tracing: Fix cmp_entries_dup() to respect sort() comparison rules
Pull HID fixes from Benjamin Tissoires:
- regression fix in suspend/resume for i2c-hid (Kenny Levinsen)
- fix wacom driver assuming a name can not be null (WangYuli)
- a couple of constify changes/fixes (Thomas Weißschuh)
- a couple of selftests/hid fixes (Maximilian Heyne & Benjamin
Tissoires)
* tag 'hid-for-linus-2024120501' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
selftests/hid: fix kfunc inclusions with newer bpftool
HID: bpf: drop unneeded casts discarding const
HID: bpf: constify hid_ops
selftests: hid: fix typo and exit code
HID: wacom: fix when get product name maybe null pointer
HID: i2c-hid: Revert to using power commands to wake on resume
