This adds a few small quirks to handle the differences between
the STM32 and Ux500 cryp blocks. The following differences
are handled with special bool switch bits in the capabilities:
- The main difference is that some registers are removed, so we
add register offsets for all registers in the
per-variant data. Then we assign the right offsets for Ux500
vs the STM32 variants.
- The Ux500 does not support the aeads algorithms; gcm(aes)
and ccm(aes). Avoid registering them when running on Ux500.
- The Ux500 has a special "linear" key format and does some
elaborare bit swizzling of the key bits before writing them
into the key registers. This is written as an "application
note" inside the DB8500 design specification, and seems to
be the result of some mishap when assigning the data lines
to register bits. (STM32 has clearly fixed this.)
- The Ux500 does not have the KP "key prepare" bit in the
CR register. Instead, we need to set the KSE bit,
"key schedule encryption" bit which does the same thing
but is in bit 11 rather than being a special "algorithm
type" as on STM32. The algorithm must however be specified
as AES ECB while doing this.
- The Ux500 cannot just read out IV registers, we need to
set the KEYRDEN "key read enable" bit, as this protects
not just the key but also the IV from being read out.
Enable this bit before reading out the IV and disable it
afterwards.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds device tree bindings for the Ux500 CRYP block
as a compatible in the STM32 CRYP bindings.
The Ux500 CRYP binding has been used for ages in the kernel
device tree for Ux500 but was never documented, so fill in
the gap by making it a sibling of the STM32 CRYP block,
which is what it is.
The relationship to the existing STM32 CRYP block is pretty
obvious when looking at the register map, and I have written
patches to reuse the STM32 CRYP driver on the Ux500.
The two properties added are DMA channels and power domain.
Power domains are a generic SoC feature and the STM32 variant
also has DMA channels.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Lionel Debieve <lionel.debieve@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path.
Fixes: ef5d862734 ("[PATCH] Add Geode HW RNG driver")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the normal and error path.
Fixes: 96d63c0297 ("[PATCH] Add AMD HW RNG driver")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the frame_push and frame_pop macros to set up the stack frame so
that return address protections will be enabled automically when
configured.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the frame_push and frame_pop macros to set up the stack frame so
that return address protections will be enabled automically when
configured.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the frame_push and frame_pop macros to create the stack frames in
the AES chaining mode wrappers so that they will get PAC and/or shadow
call stack protection when configured.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the frame_push and frame_pop macros consistently to create the stack
frame, so that we will get PAC and/or shadow call stack handling as well
when enabled.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes the sparse warning about arrays of flexible
structures by removing an unnecessary use of them in struct
__crypto_ctx.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The acomp API allows to send requests with a NULL destination buffer. In
this case, the algorithm implementation needs to allocate the
destination scatter list, perform the operation and return the buffer to
the user. For decompression, data is likely to expand and be bigger than
the allocated buffer.
This implements a re-submission mechanism for decompression requests
that is triggered if the destination buffer, allocated by the driver,
is not sufficiently big to store the output from decompression.
If an overflow is detected when processing the callback for a
decompression request with a NULL destination buffer, a workqueue is
scheduled. This allocates a new scatter list of size CRYPTO_ACOMP_DST_MAX,
now 128KB, creates a new firmware scatter list and resubmits the job to
the hardware accelerator.
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The acomp API allows to send requests with a NULL destination buffer. In
this case, the algorithm implementation needs to allocate the
destination scatter list, perform the operation and return the buffer to
the user. For decompression, data is likely to expand and be bigger
than the allocated buffer.
Define the maximum size (128KB) that acomp implementations will allocate
for decompression operations as destination buffer when they receive a
request with a NULL destination buffer.
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable deflate for QAT GEN4 devices.
This adds
(1) logic to create configuration entries at probe time for the
compression instances for QAT GEN4 devices;
(2) the implementation of QAT GEN4 specific compression operations,
required since the creation of the compression request template is
different between GEN2 and GEN4; and
(3) updates to the firmware API related to compression for GEN4.
The implementation configures the device to produce data compressed
dynamically, optimized for throughput over compression ratio.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add infrastructure for implementing the acomp APIs in the QAT driver and
expose the deflate algorithm for QAT GEN2 devices.
This adds
(1) the compression service which includes logic to create, allocate
and handle compression instances;
(2) logic to create configuration entries at probe time for the
compression instances;
(3) updates to the firmware API for allowing the compression service;
and;
(4) a back-end for deflate that implements the acomp api for QAT GEN2
devices.
The implementation configures the device to produce data compressed
statically, optimized for throughput over compression ratio.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename qat_crypto_dev_config() in adf_gen2_dev_config() and relocate it
to the newly created file adf_gen2_config.c.
This function is specific to QAT GEN2 devices and will be used also to
configure the compression service.
In addition change the drivers to use the dev_config() in the hardware
data structure (which for GEN2 devices now points to
adf_gen2_dev_config()), for consistency.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the structures qat_instance_backlog and qat_alg_req from
qat_crypto.h to qat_algs_send.h since they are not unique to crypto.
Both structures will be used by the compression service to support
requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The compression service requires an additional pre-allocated buffer for
each destination scatter list.
Extend the function qat_alg_sgl_to_bufl() to take an additional
structure that contains the dma address and the size of the extra
buffer which will be appended in the destination FW SGL.
The logic that unmaps buffers in qat_alg_free_bufl() has been changed to
start unmapping from buffer 0 instead of skipping the initial buffers
num_buff - num_mapped_bufs as that functionality was not used in the
code.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The structure qat_crypto_request_buffs which contains the source and
destination buffer lists and correspondent sizes and dma addresses is
also required for the compression service.
Rename it as qat_request_buffs and move it to qat_bl.h.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The functions qat_alg_sgl_to_bufl() and qat_alg_free_bufl() take as
argument a qat_crypto_instance and a qat_crypto_request structure.
These two structures are used only to get a reference to the
adf_accel_dev and qat_crypto_request_buffs.
In order to reuse these functions for the compression service, change
the signature so that they take adf_accel_dev and
qat_crypto_request_buffs.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename the functions qat_alg_sgl_to_bufl() and qat_alg_free_bufl() as
qat_bl_sgl_to_bufl() and qat_bl_free_bufl() after their relocation into
the qat_bl module.
This commit does not implement any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the logic that maps, unmaps and converts scatterlists into QAT
bufferlists from qat_algs.c to a new module, qat_bl.
This is to allow reuse of the logic by the data compression service.
This commit does not implement any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Directly including asm/cache.h leads to build failures on powerpc
so replace it with linux/cache.h instead.
Fixes: e634ac4a8a ("crypto: api - Add crypto_tfm_ctx_dma")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit d2825fa936 ("crypto: sm3,sm4 - move into crypto directory") moves
the SM3 and SM4 stand-alone library and the algorithm implementation for
the Crypto API into the same directory, and the corresponding relationship
of Kconfig is modified, CONFIG_CRYPTO_SM3/4 corresponds to the stand-alone
library of SM3/4, and CONFIG_CRYPTO_SM3/4_GENERIC corresponds to the
algorithm implementation for the Crypto API. Therefore, it is necessary
for this module to depend on the correct algorithm.
Fixes: d2825fa936 ("crypto: sm3,sm4 - move into crypto directory")
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds helpers to access the kpp context structure and
request context structure with an added alignment for DMA access.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds helpers to access the akcipher context structure and
request context structure with an added alignment for DMA access.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Previously we limited the maximum alignment mask to 63. This
is mostly due to stack usage for shash. This patch introduces
a separate limit for shash algorithms and increases the general
limit to 127 which is the value that we need for DMA allocations
on arm64.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds helpers to access the skcipher context structure and
request context structure with an added alignment for DMA access.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds helpers to access the ahash context structure and
request context structure with an added alignment for DMA access.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds helpers to access the aead context structure and
request context structure with an added alignment for DMA access.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the helpers crypto_tfm_ctx_aligned and
crypto_tfm_ctx_dma. The first aligns the tfm context to the
value cra_alignmask. The second sets the alignment according
to dma_cache_get_alignment();
This patch also moves crypto_tfm_ctx into algapi.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The helper crypto_tfm_ctx is only used by the Crypto API algorithm
code and should really be in algapi.h. However, for historical
reasons many files relied on it to be in crypto.h. This patch
changes those files to use algapi.h instead in prepartion for a
move.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
omap_sham_probe() calls pm_runtime_get_sync() and calls
pm_runtime_put_sync() latter to put usage_counter. However,
pm_runtime_get_sync() will increment usage_counter even it failed. Fix
it by replacing it with pm_runtime_resume_and_get() to keep usage
counter balanced.
Fixes: b359f034c8 ("crypto: omap-sham - Convert to use pm_runtime API")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
curve25519-x86_64.c fails to build when CONFIG_GCOV_KERNEL is enabled.
The error is "inline assembly requires more registers than available"
thrown from the `fsqr()` function. Therefore, excluding this file from
GCOV profiling until this issue is resolved. Thereby allowing
CONFIG_GCOV_PROFILE_ALL to be enabled for x86.
Signed-off-by: Joe Fradley <joefradley@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no real point in allocating dedicated memory for the irqs array.
MAXFLOW is only 2, so it is easier to allocated the needed space
directly within the 'meson_dev' structure.
This saves some memory allocation and avoids an indirection when using the
irqs array.
Fixes: 48fe583fe5 ("crypto: amlogic - Add crypto accelerator...")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize cannot be determined in case of fallbacks.
Therefore it must be stored in the tfm and not the alg object.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize cannot be determined in case of fallbacks.
Therefore it must be stored in the tfm and not the alg object.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
