Previously we falsely relied on the PHY driver to unconditionally
enable the internal RX delay. Since the following fix for the PHY
driver this is not the case anymore:
commit 7b005a1742 ("net: phy: mscc: configure both RX and TX internal
delays for RGMII")
In order to enable the delay we need to set the connection type to
"rgmii-rxid". Without the RX delay the ethernet is not functional at
all.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.
This removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts.
Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').
With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deasserted anytime. Fix the polarity and mark it as always-on.
Anyway, using the regulator is only a workaround for the missing support of
specifying a reset GPIO for USB devices in a generic way. As we don't
have a solution for this at the moment, at least fix the current
workaround.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet the typical value for VDD_SNVS should be
800 mV, so let's make sure that this is within the range of the
regulator.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It looks like the voltages for the SOC and DRAM supply weren't properly
validated before. The datasheet and uboot-imx code tells us that VDD_SOC
should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM should be
950 mV for DDR clock frequencies of up to 1.5 GHz.
Let's fix these values to make sure the voltages are within the required
range.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Starting with commit 6b2117ad65 ("of: property: fw_devlink: Add
support for "resets" and "pwms""), the imx-drm driver fails to load
due to forever dormant devlinks to the reset-controller node. This
node was never associated with a struct device.
Add a platform device to allow fw_devnode to activate the devlinks.
Fixes: 6b2117ad65 ("of: property: fw_devlink: Add support for "resets" and "pwms"")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Any pending interrupt can prevent entering standby based power off state.
To avoid it, disable the GIC CPU interface.
Fixes: 8148d21360 ("ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the LS1028A this instance of the eSDHC controller is intended for
either an eMMC or eSDIO card. It doesn't provide a card detect pin and
its IO voltage is fixed at 1.8V.
Remove the bogus broken-cd property, instead add the non-removable
property. Fix the voltage-ranges property and set it to 1.8V only.
Fixes: 491d3a3fc1 ("arm64: dts: ls1028a: Add esdhc node in dts")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The buck2 output of the PMIC is the VDD core voltage of the cpu.
Switching off this will poweroff the CPU. Add the 'regulator-always-on'
property to avoid this.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Before commit 0e30f47232 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
qspi and fspi host controller do not support read 1-4-4 mode. so need to
set the tx to 1, let the common code finally select read 1-1-4 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Before commit 0e30f47232 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit cc8870bf4c.
Since commit cc8870bf4c ("ARM: imx6q: drop of_platform_default_populate()
from init_machine") the following errors are seen on boot:
[ 0.123372] imx6q_suspend_init: failed to find ocram device!
[ 0.123537] imx6_pm_common_init: No DDR LPM support with suspend -19!
, which break suspend/resume on imx6q/dl.
Revert the offeding commit to avoid the regression.
Thanks to Tim Harvey for bisecting this problem.
Cc: stable@vger.kernel.org
Fixes: cc8870bf4c ("ARM: imx6q: drop of_platform_default_populate() from init_machine")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the LED multicolor framework support was added in commit
92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Add missing fields and remove some duplicate fields when printing a
perf_event_attr.
- Fix hybrid config terms list corruption.
- Update kernel header copies, some resulted in new kernel features
being automagically added to 'perf trace' syscall/tracepoint argument
id->string translators.
- Add a file generated during the documentation build to .gitignore.
- Add an option to build without libbfd, as some distros, like Debian
consider its ABI unstable.
- Add support to print a textual representation of IBS raw sample data
in 'perf report'.
- Fix bpf 'perf test' sample mismatch reporting
- Fix passing arguments to stackcollapse report in a 'perf script'
python script.
- Allow build-id with trailing zeros.
- Look for ImageBase in PE file to compute .text offset.
* tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (25 commits)
tools headers UAPI: Update tools's copy of drm.h headers
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/fs.h with the kernel sources
tools headers UAPI: Sync linux/in.h copy with the kernel sources
perf tools: Add an option to build without libbfd
perf tools: Allow build-id with trailing zeros
perf tools: Fix hybrid config terms list corruption
perf tools: Factor out copy_config_terms() and free_config_terms()
perf tools: Fix perf_event_attr__fprintf() missing/dupl. fields
perf tools: Ignore Documentation dependency file
perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
tools include UAPI: Update linux/mount.h copy
perf beauty: Cover more flags in the move_mount syscall argument beautifier
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
perf report: Add support to print a textual representation of IBS raw sample data
perf report: Add tools/arch/x86/include/asm/amd-ibs.h
perf env: Add perf_env__cpuid, perf_env__{nr_}pmu_mappings
...
Pull compiler attributes updates from Miguel Ojeda:
- Fix __has_attribute(__no_sanitize_coverage__) for GCC 4 (Marco Elver)
- Add Nick as Reviewer for compiler_attributes.h (Nick Desaulniers)
- Move __compiletime_{error|warning} (Nick Desaulniers)
* tag 'compiler-attributes-for-linus-v5.15-rc1-v2' of git://github.com/ojeda/linux:
compiler_attributes.h: move __compiletime_{error|warning}
MAINTAINERS: add Nick as Reviewer for compiler_attributes.h
Compiler Attributes: fix __has_attribute(__no_sanitize_coverage__) for GCC 4
Pull auxdisplay updates from Miguel Ojeda:
"An assortment of improvements for auxdisplay:
- Replace symbolic permissions with octal permissions (Jinchao Wang)
- ks0108: Switch to use module_parport_driver() (Andy Shevchenko)
- charlcd: Drop unneeded initializers and switch to C99 style (Andy
Shevchenko)
- hd44780: Fix oops on module unloading (Lars Poeschel)
- Add I2C gpio expander example (Ralf Schlatterbeck)"
* tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux:
auxdisplay: Replace symbolic permissions with octal permissions
auxdisplay: ks0108: Switch to use module_parport_driver()
auxdisplay: charlcd: Drop unneeded initializers and switch to C99 style
auxdisplay: hd44780: Fix oops on module unloading
auxdisplay: Add I2C gpio expander example
Pull CPU hotplug updates from Thomas Gleixner:
"Updates for the SMP and CPU hotplug:
- Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
original hotplug code and now causing trouble with the ARM64 cache
topology setup due to the pointless SMP function call.
It's not longer required as the hotplug callbacks are guaranteed to
be invoked on the upcoming CPU.
- Remove the deprecated and now unused CPU hotplug functions
- Rewrite the CPU hotplug API documentation"
* tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: core-api/cpuhotplug: Rewrite the API section
cpu/hotplug: Remove deprecated CPU-hotplug functions.
thermal: Replace deprecated CPU-hotplug functions.
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()
Pull misc driver fix from Greg KH:
"Here is a single patch for 5.15-rc1, for the lkdtm misc driver.
It resolves a build issue that many people were hitting with your
current tree, and Kees and others felt would be good to get merged
before -rc1 comes out, to prevent them from having to constantly hit
it as many development trees restart on -rc1, not older -rc releases.
It has NOT been in linux-next, but has passed 0-day testing and looks
'obviously correct' when reviewing it locally :)"
* tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
lkdtm: Use init_uts_ns.name instead of macros
Pull IPMI updates from Corey Minyard:
"A couple of very minor fixes for style and rate limiting.
Nothing big, but probably needs to go in"
* tag 'for-linus-5.15-1' of git://github.com/cminyard/linux-ipmi:
char: ipmi: use DEVICE_ATTR helper macro
ipmi: rate limit ipmi smi_event failure message
Pull scheduler fixes from Borislav Petkov:
- Make sure the idle timer expires in hardirq context, on PREEMPT_RT
- Make sure the run-queue balance callback is invoked only on the
outgoing CPU
* tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Prevent balance_push() on remote runqueues
sched/idle: Make the idle timer expire in hard interrupt context
Pull locking fixes from Borislav Petkov:
- Fix the futex PI requeue machinery to not return to userspace in
inconsistent state
- Avoid a potential null pointer dereference in the ww_mutex deadlock
check
- Other smaller cleanups and optimizations
* tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Fix ww_mutex deadlock check
futex: Remove unused variable 'vpid' in futex_proxy_trylock_atomic()
futex: Avoid redundant task lookup
futex: Clarify comment for requeue_pi_wake_futex()
futex: Prevent inconsistent state and exit race
futex: Return error code instead of assigning it without effect
locking/rwsem: Add missing __init_rwsem() for PREEMPT_RT
Pull timer fix from Borislav Petkov:
- Handle negative second values properly when converting a timespec64
to nanoseconds.
* tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Handle negative seconds correctly in timespec64_to_ns()
Pull namei updates from Al Viro:
"Clearing fallout from mkdirat in io_uring series. The fix in the
kern_path_locked() patch plus associated cleanups"
* 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
putname(): IS_ERR_OR_NULL() is wrong here
namei: Standardize callers of filename_create()
namei: Standardize callers of filename_lookup()
rename __filename_parentat() to filename_parentat()
namei: Fix use after free in kern_path_locked
Pull smbfs updates from Steve French:
"cifs/smb3 updates:
- DFS reconnect fix
- begin creating common headers for server and client
- rename the cifs_common directory to smbfs_common to be more
consistent ie change use of the name cifs to smb (smb3 or smbfs is
more accurate, as the very old cifs dialect has long been
superseded by smb3 dialects).
In the future we can rename the fs/cifs directory to fs/smbfs.
This does not include the set of multichannel fixes nor the two
deferred close fixes (they are still being reviewed and tested)"
* tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: properly invalidate cached root handle when closing it
cifs: move SMB FSCTL definitions to common code
cifs: rename cifs_common to smbfs_common
cifs: update FSCTL definitions
Pull virtio updates from Michael Tsirkin:
- vduse driver ("vDPA Device in Userspace") supporting emulated virtio
block devices
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
Pull more RISC-V updates from Palmer Dabbelt:
- A pair of defconfig additions, for NVMe and the EFI filesystem
localization options.
- A larger address space for stack randomization.
- A cleanup to our install rules.
- A DTS update for the Microchip Icicle board, to fix the serial
console.
- Support for build-time table sorting, which allows us to have
__ex_table read-only.
* tag 'riscv-for-linus-5.15-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Move EXCEPTION_TABLE to RO_DATA segment
riscv: Enable BUILDTIME_TABLE_SORT
riscv: dts: microchip: mpfs-icicle: Fix serial console
riscv: move the (z)install rules to arch/riscv/Makefile
riscv: Improve stack randomisation on RV64
riscv: defconfig: enable NLS_CODEPAGE_437, NLS_ISO8859_1
riscv: defconfig: enable BLK_DEV_NVME
Pull coccinelle updates from Julia Lawall:
"These changes update some existing semantic patches with
respect to some recent changes in the kernel.
Specifically, the change to kvmalloc.cocci searches for
kfree_sensitive rather than kzfree, and the change to
use_after_iter.cocci adds list_entry_is_head as a valid
use of a list iterator index variable after the end of
the loop"
* 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccinelle: allow list_entry_is_head() to use pos
coccinelle: api: rename kzfree to kfree_sensitive
Picking the changes from:
17ce9c61c7 ("drm: document DRM_IOCTL_MODE_RMFB")
Doesn't result in any tooling changes:
$ tools/perf/trace/beauty/drm_ioctl.sh > before
$ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
$ tools/perf/trace/beauty/drm_ioctl.sh > after
$ diff -u before after
Silencing these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h
Cc: Simon Ser <contact@emersion.fr>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the changes in:
b65a948973 ("drm/i915/userptr: Probe existence of backing struct pages upon creation")
ee242ca704 ("drm/i915/guc: Implement GuC priority management")
81340cf3bd ("drm/i915/uapi: reject set_domain for discrete")
7961c5b60f ("drm/i915: Add TTM offset argument to mmap.")
aef7b67a79 ("drm/i915/uapi: convert drm_i915_gem_userptr to kernel doc")
e7737b67ab ("drm/i915/uapi: reject caching ioctls for discrete")
3aa8c57fe2 ("drm/i915/uapi: convert drm_i915_gem_set_domain to kernel doc")
289f5a7200 ("drm/i915/uapi: convert drm_i915_gem_caching to kernel doc")
4a766ae40e ("drm/i915: Drop the CONTEXT_CLONE API (v2)")
6ff6d61dd2 ("drm/i915: Drop I915_CONTEXT_PARAM_NO_ZEROMAP")
fe4751c3d5 ("drm/i915: Drop I915_CONTEXT_PARAM_RINGSIZE")
577729533c ("drm/i915: Document the Virtual Engine uAPI")
c649432e86 ("drm/i915: Fix busy ioctl commentary")
That doesn't result in any changes to tooling as no new ioctl were
added (at least not perceived by tools/perf/trace/beauty/drm_ioctl.sh).
Addressing this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the change in:
7957d93bf3 ("block: add ioctl to read the disk sequence number")
It adds a new ioctl, but we are still not using that to generate tables
for 'perf trace', so no changes in tooling.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the changes in:
db243b7964 ("net/ipv4/ipv6: Replace one-element arraya with flexible-array members")
2d3e5caf96 ("net/ipv4: Replace one-element array with flexible-array member")
That don't result in any change in tooling, the structs changed remains
with the same layout.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115 ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull io_uring fixes from Jens Axboe:
- Fix an off-by-one in a BUILD_BUG_ON() check. Not a real issue right
now as we have plenty of flags left, but could become one. (Hao)
- Fix lockdep issue introduced in this merge window (me)
- Fix a few issues with the worker creation (me, Pavel, Qiang)
- Fix regression with wq_has_sleeper() for IOPOLL (Pavel)
- Timeout link error propagation fix (Pavel)
* tag 'io_uring-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
io_uring: fix off-by-one in BUILD_BUG_ON check of __REQ_F_LAST_BIT
io_uring: fail links of cancelled timeouts
io-wq: fix memory leak in create_io_worker()
io-wq: fix silly logic error in io_task_work_match()
io_uring: drop ctx->uring_lock before acquiring sqd->lock
io_uring: fix missing mb() before waitqueue_active
io-wq: fix cancellation on create-worker failure
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph:
- fix nvmet command set reporting for passthrough controllers (Adam Manzanares)
- update a MAINTAINERS email address (Chaitanya Kulkarni)
- set QUEUE_FLAG_NOWAIT for nvme-multipth (me)
- handle errors from add_disk() (Luis Chamberlain)
- update the keep alive interval when kato is modified (Tatsuya Sasaki)
- fix a buffer overrun in nvmet_subsys_attr_serial (Hannes Reinecke)
- do not reset transport on data digest errors in nvme-tcp (Daniel Wagner)
- only call synchronize_srcu when clearing current path (Daniel Wagner)
- revalidate paths during rescan (Hannes Reinecke)
- Split out the fs/block_dev into block/fops.c and block/bdev.c, which
has been long overdue. Do this now before -rc1, to avoid annoying
conflicts due to this (Christoph)
- blk-throtl use-after-free fix (Li)
- Improve plug depth for multi-device plugs, greatly increasing md
resync performance (Song)
- blkdev_show() locking fix (Tetsuo)
- n64cart error check fix (Yang)
* tag 'block-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
n64cart: fix return value check in n64cart_probe()
blk-mq: allow 4x BLK_MAX_REQUEST_COUNT at blk_plug for multiple_queues
block: move fs/block_dev.c to block/bdev.c
block: split out operations on block special files
blk-throttle: fix UAF by deleteing timer in blk_throtl_exit()
block: genhd: don't call blkdev_show() with major_names_lock held
nvme: update MAINTAINERS email address
nvme: add error handling support for add_disk()
nvme: only call synchronize_srcu when clearing current path
nvme: update keep alive interval when kato is modified
nvme-tcp: Do not reset transport on data digest errors
nvmet: fixup buffer overrun in nvmet_subsys_attr_serial()
nvmet: return bool from nvmet_passthru_ctrl and nvmet_is_passthru_req
nvmet: looks at the passthrough controller when initializing CAP
nvme: move nvme_multi_css into nvme.h
nvme-multipath: revalidate paths during rescan
nvme-multipath: set QUEUE_FLAG_NOWAIT
Pull libata maintainer update from Jens Axboe:
"Damien agreed to take over maintainership of libata, and he would be a
great candidate for it. Update the MAINTAINERS entry to reflect the
change in maintainer and git tree"
* tag 'libata-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
libata: pass over maintainership to Damien Le Moal
Pull tracing fixes from Steven Rostedt:
"Minor fixes to the processing of the bootconfig tree"
* tag 'trace-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Rename xbc_node_find_child() to xbc_node_find_subkey()
tracing/boot: Fix to check the histogram control param is a leaf node
tracing/boot: Fix trace_boot_hist_add_array() to check array is value
Pull devicetree fixes from Rob Herring:
- Disable fw_devlinks on x86 DT platforms to fix OLPC
- More replacing oneOf+const with enum on a few new schemas
- Drop unnecessary type references on Xilinx SPI binding schema
* tag 'devicetree-fixes-for-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
spi: dt-bindings: xilinx: Drop type reference on *-bits properties
dt-bindings: More use 'enum' instead of 'oneOf' plus 'const' entries
of: property: Disable fw_devlink DT support for X86
Pull clk fix from Stephen Boyd:
"One patch to fix an unused variable warning in a Qualcomm clk driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc-sm6350: Remove unused variable
Pull RTC updates from Alexandre Belloni:
"The broken down time conversion is similar to what is done in the time
subsystem since v5.14. The rest is fairly straightforward.
Subsystem:
- Switch to Neri and Schneider time conversion algorithm
Drivers:
- rx8025: add rx8035 support
- s5m: modernize driver and set range"
* tag 'rtc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: rx8010: select REGMAP_I2C
dt-bindings: rtc: add Epson RX-8025 and RX-8035
rtc: rx8025: implement RX-8035 support
rtc: cmos: remove stale REVISIT comments
rtc: tps65910: Correct driver module alias
rtc: move RTC_LIB_KUNIT_TEST to proper location
rtc: lib_test: add MODULE_LICENSE
rtc: Improve performance of rtc_time64_to_tm(). Add tests.
rtc: s5m: set range
rtc: s5m: enable wakeup only when available
rtc: s5m: signal the core when alarm are not available
rtc: s5m: switch to devm_rtc_allocate_device
