Reporting alarms using hwmon_notify_event() may result in a callback
from the thermal subsystem. This means that such notifications must
not hold the update lock to avoid a deadlock. To avoid this situation,
use a worker to handle notifications.
Reported-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Fixes: f6d0775119 ("hwmon: (lm90) Rework alarm/status handling")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new assembly code works on both 32 bit and 64 bit
cpus and allows for more compiler optimisations.
Since clang runs out of registers on 32 bit x86 when
using CC_OUT, we need to execute "setc" ourself.
Also modify the debug message so we can still see
the result (eax) when the carry flag was set.
Tested with 32 bit and 64 bit kernels on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220220190851.17965-1-W_Armin@gmx.de
[groeck: Rebased to v5.19-rc3]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC2977 regulator does not set the regulator_desc .n_voltages value
which is needed in order to let the regulator core list the regulator
voltage range.
This patch defines a regulator_desc with a voltage range, and uses it
for defining voltage resolution for regulators LTC2972/LTC2974/LTC2975/
LTC2977/LTC2978/LTC2979/LTC2980/LTM2987 based on that they all have a 16
bit ADC with the same stepwise 122.07uV resolution. It also scales the
resolution to a 1mV resolution which is easier to handle.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614095144.3472305-1-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When checking if a regulator supports a voltage range, the regulator
needs to have a list_voltage callback set to the regulator_ops or else
-EINVAL will be returned. This support does not exist for the pmbus
regulators, so this patch adds pmbus_regulator_list_voltage to the
pmbus_regulator_ops.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614093856.3470672-3-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When setting a new voltage the voltage boundaries are read every time to
check that the new voltage is within the proper range. Checking these
voltage boundaries consists of reading one of PMBUS_MFR_VOUT_MIN/
PMBUS_VOUT_MARGIN_LOW registers and then PMBUS_MFR_VOUT_MAX/
PMBUS_VOUT_MARGIN_HIGH together with writing the PMBUS_CLEAR_FAULTS
register.
Since these boundaries are never being changed, it can be cached and
thus saving unnecessary smbus transmissions.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220614093856.3470672-2-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A user reported that the program dell-bios-fan-control
worked on his Dell XPS 13 7390 to switch off automatic
fan control.
Since it uses the same mechanism as the dell_smm_hwmon
module, add this model to the fan control whitelist.
Compile-tested only.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220612041806.11367-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_PMBUS is y and CONFIG_DEBUG_FS is not set.
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-, will be failed, like this:
drivers/hwmon/pmbus/pmbus_core.c:593:13: error: ‘pmbus_check_block_register’ defined but not used [-Werror=unused-function]
static bool pmbus_check_block_register(struct i2c_client *client, int page,
^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/hwmon/pmbus/pmbus_core.o] Error 1
make[2]: *** [drivers/hwmon/pmbus] Error 2
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [drivers/hwmon] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [drivers] Error 2
To fix building warning, use __maybe_unused to attach this func.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: c3ffc3a1ff83("hwmon: (pmbus) add a function to check the presence of a block register")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220609120448.139907-1-renzhijie2@huawei.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add registers to debugfs:
PMBUS_MFR_ID
PMBUS_MFR_MODEL
PMBUS_MFR_REVISION
PMBUS_MFR_LOCATION
PMBUS_MFR_DATE
PMBUS_MFR_SERIAL
To reduce the number of debugfs entries, only values from page 0 are
reported. It is assumed that values of these registers are the same for
all pages. Please note that the PMBUS standard allows added registers to
be page-specific.
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220601013232.801133-2-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some devices like the Fujitsu Celsius W380 do contain
a working sch56xx hardware monitoring device, but do
not contain the necessary DMI onboard device.
Do not check for the presence of an suitable onboard device
on these machines. The list of affected machines was created
using data collected by the Linux Hardware Project.
Tested on a Fujitsu Esprimo P720, but sadly not on a affected
machine.
Fixes: 393935baa4 (hwmon: (sch56xx-common) Add automatic module loading on supported devices)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220604220200.2567-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Analog Devices LT7182S Dual Channel 6A, 20V PolyPhase
Step-Down Silent Switcher with Digital Power System Management.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the chips supported by this driver support configuring the
number of samples (or the fault queue depth) necessary before a fault
or alarm is reported. This is done either with a bit in the configuration
register or with a separate "consecutive alert" register. Support this
functionality with the temp_samples attribute.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add table with device names and known register values for supported
devices from Analog / ON Semiconductor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was observed that the alert handler may be called from the i2c core
even after alerts have already been disabled. Only disable alerts if
they have not already been disabled.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7421 is similar to ADT7461A but supports configurable Beta Compensation.
Packet Error Checking (PEC) is supported but undocumented.
A devicetree node is not added for the added chip since it is quite
unlikely that such an old chip will ever be used in a devicetree based
system. It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM86 and LM90 support exactly the same features, so there is no need
to keep their configuration options separate. Combine to reduce data
size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify the code a bit by handling single-register read operations
in lm90_read16(). All we need to do is to skip the low-byte read
operation if the register address is 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating support for setting the conversion rate doesn't cost
much and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating support for minimum temperature limits doesn't cost much
and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
