The type name enum req_opf is misleading since it suggests that values of
this type include both an operation type and flags. Since values of this
type represent an operation only, change the type name into enum req_op.
Convert the enum req_op documentation into kernel-doc format. Move a few
definitions such that the enum req_op documentation occurs just above
the enum req_op definition.
The name "req_opf" was introduced by commit ef295ecf09 ("block: better op
and flags encoding").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.
When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.
Therefore, add a progress to configure tunnel neighbour in this case.
v2: Correct format of fixes tag.
Fixes: f1df7956c1 ("nfp: flower: rework tunnel neighbour configuration")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DRM_AMD_DC_DCN display engine support (Raven, Navi, and newer) has
not been building cleanly on powerpc and causes link errors due to
mixing hard- and soft-float object files:
powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o uses soft float
powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o
[..]
and while patches are floating around, it's not exactly obvious what is
going on.
The problem bisects to commit 41b7a347bf ("powerpc: Book3S 64-bit
outline-only KASAN support") but that is probably more about changing
config variables than the fundamental cause.
Despite the bisection result, a more directly related commit seems to be
26f4712aed ("drm/amd/display: move FPU related code from dcn31 to
dml/dcn31 folder"). It's probably a combination of the two.
This has been going on since the merge window, without any final word.
So instead of blindly applying patches that may or may not be the right
thing, let's disable this for now.
As Michael Ellerman says:
"IIUIC this code was never enabled on ppc before, so disabling it seems
like a reasonable fix to get the build clean"
and once we have more actual feedback (and find any potential users) we
can always re-enable it with the patch that fixes the issues and
back-port as necessary.
Fixes: 41b7a347bf ("powerpc: Book3S 64-bit outline-only KASAN support")
Fixes: 26f4712aed ("drm/amd/display: move FPU related code from dcn31 to dml/dcn31 folder")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/all/20220606153910.GA1773067@roeck-us.net/
Link: https://lore.kernel.org/all/20220618232737.2036722-1-linux@roeck-us.net/
Link: https://lore.kernel.org/all/20220713050724.GA2471738@roeck-us.net/
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 513616843d ("block: remove superfluous calls to
blkcg_bio_issue_init") has removed blkcg_bio_issue_init from
__bio_clone since submit_bio will override ->bi_issue.
However, __blk_queue_split is called after blkcg_bio_issue_init
(see blk_mq_submit_bio) in submit_bio. In this case, the
->bi_issue is 0. Fix it.
Fixes: 513616843d ("block: remove superfluous calls to blkcg_bio_issue_init")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Link: https://lore.kernel.org/r/20220713140226.68135-1-songmuchun@bytedance.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mmp_bdevname is currently both initialized nested inside the kthread_run
call in ext4_multi_mount_protect and in the kmmpd thread started by it.
Lift the initiaization out of the kthread_run call in
ext4_multi_mount_protect, move the BUILD_BUG_ON next to it and remove
the duplicate assignment inside of kmmpd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220713055317.1888500-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The initially merged version of the igc driver code (via commit
146740f9ab, "igc: Add support for PF") contained the following
IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors:
u32 igc_rd32(struct igc_hw *hw, u32 reg)
{
u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr);
u32 value = 0;
if (IGC_REMOVED(hw_addr))
return ~value;
value = readl(&hw_addr[reg]);
/* reads should not return all F's */
if (!(~value) && (!reg || !(~readl(hw_addr))))
hw->hw_addr = NULL;
return value;
}
And:
#define wr32(reg, val) \
do { \
u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \
if (!IGC_REMOVED(hw_addr)) \
writel((val), &hw_addr[(reg)]); \
} while (0)
E.g. igb has similar checks in its MMIO accessors, and has a similar
macro E1000_REMOVED, which is implemented as follows:
#define E1000_REMOVED(h) unlikely(!(h))
These checks serve to detect and take note of an 0xffffffff MMIO read
return from the device, which can be caused by a PCIe link flap or some
other kind of PCI bus error, and to avoid performing MMIO reads and
writes from that point onwards.
However, the IGC_REMOVED macro was not originally implemented:
#ifndef IGC_REMOVED
#define IGC_REMOVED(a) (0)
#endif /* IGC_REMOVED */
This led to the IGC_REMOVED logic to be removed entirely in a
subsequent commit (commit 3c215fb18e, "igc: remove IGC_REMOVED
function"), with the rationale that such checks matter only for
virtualization and that igc does not support virtualization -- but a
PCIe device can become detached even without virtualization being in
use, and without proper checks, a PCIe bus error affecting an igc
adapter will lead to various NULL pointer dereferences, as the first
access after the error will set hw->hw_addr to NULL, and subsequent
accesses will blindly dereference this now-NULL pointer.
This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and
implements IGC_REMOVED the way it is done for igb, by checking for the
unlikely() case of hw_addr being NULL. This change prevents the oopses
seen when a PCIe link flap occurs on an igc adapter.
Fixes: 146740f9ab ("igc: Add support for PF")
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
'vector' and 'trig_mode' fields of 'struct kvm_lapic_irq' are left
uninitialized in kvm_pv_kick_cpu_op(). While these fields are normally
not needed for APIC_DM_REMRD, they're still referenced by
__apic_accept_irq() for trace_kvm_apic_accept_irq(). Fully initialize
the structure to avoid consuming random stack memory.
Fixes: a183b638b6 ("KVM: x86: make apic_accept_irq tracepoint more generic")
Reported-by: syzbot+d6caa905917d353f0d07@syzkaller.appspotmail.com
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220708125147.593975-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This pull request contains Broadcom ARM64-based SocS Device Tree
updates for 5.20, please pull the following:
- William adds the ARCH_BCMBCA Kconfig entry to follow the ARM 32-bit
counter part and adds basic support for these DSL/PON SoCs: 63158,
4912, 63146, 6856, 6813
- Anand adds basic support for the 6858 SoC
- Krzysztof fixes a missing space between a property name and its value
in a number of DTS files
* tag 'arm-soc/for-5.20/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: Add DTS files for bcmbca SoC BCM6813
arm64: dts: Add DTS files for bcmbca SoC BCM6856
arm64: dts: Add DTS files for bcmbca SoC BCM63146
arm64: dts: broadcom: adjust whitespace around '='
ARM64: dts: Add DTS files for bcmbca SoC BCM6858
arm64: dts: Add DTS files for bcmbca SoC BCM4912
arm64: dts: Add DTS files for bcmbca SoC BCM63158
arm64: bcmbca: add arch bcmbca machine entry
Link: https://lore.kernel.org/r/20220711164451.3542127-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.20, please pull the following:
- Stefan drops the unnecessary "#address-cells" and "#size-cells"
properties from the DPI node of BCM283x
- Anand documents and adds support for the 63178 and 6858 SoCs
- William migrates the 63138 platform over to ARCH_BCMBCA and ensures
that it is documented within the BCMBCA Device Tree binding documents.
He updates the 47622 DTS to remove unnecessary PSCI properties, fix
the GIC nodes and some minor cosmetic changes. He finally adds support
for the 63158, 4912, 6846, 6855, 6756, 63146, 6856, 63148, 6813, 6318
SoCs.
- Peter, Nicolas and Stefan adds the necessary Device Tree nodes to the
BCM2711 (Raspberry Pi 4) DTS to enable the use of the V3D GPU on these
platforms.
- Christian adds support for the BCM53015 based Cisco Meraki MR26
Wi-Fi access point.
- Krzysztof updates the Broadcom platforms DTS to add a missing
whitespace between the property name and its value.
* tag 'arm-soc/for-5.20/devicetree' of https://github.com/Broadcom/stblinux: (35 commits)
ARM: dts: Add BCM63138 generic board dts
ARM: dts: update dts files for bcmbca SoC BCM63138
ARM: dts: Move BCM963138DVT board dts to ARCH_BCMBCA
dt-bindings: arm: add BCM63138 SoC
ARM: dts: bcm2711: Use proper compatible in PM/Watchdog node
ARM: dts: bcm2835/bcm2711: Introduce reg-names in watchdog node
dt-bindings: soc: bcm: bcm2835-pm: Add support for bcm2711
dt-bindings: soc: bcm: bcm2835-pm: Introduce reg-names
dt-bindings: soc: bcm: bcm2835-pm: Convert bindings to DT schema
ARM: dts: BCM5301X: Add DT for Meraki MR26
dt-bindings: ARM: add bindings for the Meraki MR26
dt-bindings: arm64: Add BCM6813 SoC
ARM: dts: Add DTS files for bcmbca SoC BCM63148
dt-bindings: arm: Add BCM63148 SoC
dt-bindings: arm64: Add BCM6856 SoC
dt-bindings: arm64: Add BCM63146 SoC
ARM: dts: broadcom: correct gpio-keys properties
ARM: dts: broadcom: align gpio-key node names with dtschema
ARM: dts: Add DTS files for bcmbca SoC BCM6756
dt-bindings: arm: Add BCM6756 SoC
...
Link: https://lore.kernel.org/r/20220711164451.3542127-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DTS updates for v5.20
This introduces initial support for Lenovo ThinkPad X13s, Qualcomm 8cx
Gen 3 Compute Reference Device, SA8295P Automotive Development Platform,
Xiaomi Mi 5s Plus, five new SC7180 Chrome OS boards, Inforce IFC6560, LG
G7 ThinQ and LG V35 ThinQ.
With IPQ8074 gaining GDSC support, this was expressed in the gcc node
and defined for the USB nodes. The SDHCI reset line was defined to get
the storage devices into a known state.
For MSM8996 interconnect providers, the second DSI interface, resets for
SDHCI are introduced. Support for the Xiaomi Mi 5s Plus is introduced
and the Dragonboard 820c gains definitions for its LEDs.
The MSM8998 platform changes consists of a various cleanup patches, the
FxTec Pro1 is split out from using the MTP dts and Sony Xperia devices
on the "Yoshino" platform gains ToF sensor.
On SC7180 five new Trogdor based boards are added and the description of
keyboard and detachables is improved.
On the SC7280-based Herobrine board DisplayPort is enabled, SPI flash
clock rate is changed, WiFi is enabled and the modem firmware path is
updated. The Villager boards gains touchscreen, and keyboard backlight.
This introduces initial support for the SC8280XP (aka 8cx Gen 3) and
related automotive platforms are introduced, with support for the
Qualcomm reference board, the Lenovo Thinkpad X13s and the SA8295P
Automotive Development Platform.
In addition to a wide range of smaller fixes on the SDM630 and SDM660
platforms, support for the secondary high speed USB controller is
introduced and the Sony Xperia "Nile" platform gains support for the RGB
status LED. Support for the Inforce IFC6560 board is introduced.
On SDM845 the bandwidth monitor for the CPU subsystem is introduced, to
scale LLCC clock rate based on profiling. CPU and cluster idle states
are switched to OSI hierarchical states. DB845c and SHIFT 6mq gains LED
support and new support for the LG G7 ThinQ and LG V35 ThinQ boards are
added.
DLL/DDR configuration for SDHCI nodes are defined for SM6125.
On SM8250 the GPU per-process page tables is enabled and for RB5 the
Light Pulse Generator-based LEDs are added.
The display clock controller is introduced for SM8350.
On SM8450 this introduces the camera clock controller and the UART
typically used for Bluetooth. The interconnect path for the crypto
engine is added to the SCM node, to ensure this is adequately clocked.
The assigned-clock-rate for the display processor is dropped from
several platforms, now that the driver derrives the min and max from the
clock.
In addition to this a wide range of fixes for stylistic issues and
issues discovered through Devicetree binding validation across many
platforms and boards are introduced.
* tag 'qcom-arm64-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (193 commits)
arm64: dts: qcom: sc8280xp: fix DP PHY node unit addresses
arm64: dts: qcom: sc8280xp: fix usb_0 HS PHY ref clock
arm64: dts: qcom: sc7280: fix PCIe clock reference
docs: arm: index.rst: add google/chromebook-boot-flow
arm64: dts: qcom: msm8996: clean up PCIe PHY node
arm64: dts: qcom: msm8996: use non-empty ranges for PCIe PHYs
arm64: dts: qcom: sm8450: drop UFS PHY clock-cells
arm64: dts: qcom: sm8250: drop UFS PHY clock-cells
arm64: dts: qcom: sc8280xp: drop UFS PHY clock-cells
arm64: dts: qcom: sm8450: drop USB PHY clock index
arm64: dts: qcom: sm8350: drop USB PHY clock index
arm64: dts: qcom: msm8998: drop USB PHY clock index
arm64: dts: qcom: ipq8074: drop USB PHY clock index
arm64: dts: qcom: ipq6018: drop USB PHY clock index
arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
arm64: dts: qcom: sc7280: drop PCIe PHY clock index
Revert "arm64: dts: qcom: Fix 'reg-names' for sdhci nodes"
arm64: dts: qcom: sc7180-idp: add vdds supply to the DSI PHY
arm64: dts: qcom: sc7280: use constants for gpucc clocks and power-domains
arm64: dts: qcom: msm8996: add missing DSI clock assignments
...
Link: https://lore.kernel.org/r/20220713203939.1431054-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The issue exists when multipath is enabled and the namespace is
shared, but all the other controller checks at nvme_is_unique_nsid()
are false. The reason for this issue is that nvme_is_unique_nsid()
returns false when is called from nvme_mpath_alloc_disk() due to an
uninitialized value of head->shared. The patch fixes it by setting
head->shared before nvme_mpath_alloc_disk() is called.
Fixes: 5974ea7ce0 ("nvme: allow duplicate NSIDs for private namespaces")
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A reset on a live device experiencing a link error still needs to have
the queue freeze state started for the subsequent reinitialization. Skip
only the register read if the device is not present instead of bypassing
the freeze checks.
Fixes: b98235d3a4 ("nvme-pci: harden drive presence detect in nvme_dev_disable()")
Reported-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Johan writes:
USB-serial fixes for 5.19-rc7
Here are a couple of new device ids for ftdi_sio.
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-5.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add Belimo device ids
The usb-serial fixes are based on this branch, so merge it in here to
prevent merge confusion when merging in that tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call blk_cleanup_queue() in release code path for fixing request
queue leak.
Also for-5.20/block has cleaned up blk_cleanup_queue(), which is
basically merged to del_gendisk() if blk_mq_alloc_disk() is used
for allocating disk and queue.
However, ublk may not add disk in case of starting device failure, then
del_gendisk() won't be called when removing ublk device, so blk_mq_exit_queue
will not be callsed, and it can be bit hard to deal with this kind of
merge conflict.
Turns out ublk's queue/disk use model is very similar with scsi, so switch
to scsi's model by allocating disk and queue independently, then it can be
quite easy to handle v5.20 merge conflict by replacing blk_cleanup_queue
with blk_mq_destroy_queue.
Reported-by: Jens Axboe <axboe@kernel.dk>
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220714103201.131648-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use task_work_add if it is available, since task_work_add can bring
up better performance, especially batching signaling ->ubq_daemon can
be done.
It is observed that task_work_add() can boost iops by +4% on random
4k io test. Also except for completing io command, all other code
paths are same with completing io command via
io_uring_cmd_complete_in_task.
Meantime add one flag of UBLK_F_URING_CMD_COMP_IN_TASK for comparing
the mode easily.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220713140711.97356-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is the driver part of userspace block driver(ublk driver), the other
part is userspace daemon part(ublksrv)[1].
The two parts communicate by io_uring's IORING_OP_URING_CMD with one
shared cmd buffer for storing io command, and the buffer is read only for
ublksrv, each io command is indexed by io request tag directly, and is
written by ublk driver.
For example, when one READ io request is submitted to ublk block driver,
ublk driver stores the io command into cmd buffer first, then completes
one IORING_OP_URING_CMD for notifying ublksrv, and the URING_CMD is issued
to ublk driver beforehand by ublksrv for getting notification of any new
io request, and each URING_CMD is associated with one io request by tag.
After ublksrv gets the io command, it translates and handles the ublk io
request, such as, for the ublk-loop target, ublksrv translates the request
into same request on another file or disk, like the kernel loop block
driver. In ublksrv's implementation, the io is still handled by io_uring,
and share same ring with IORING_OP_URING_CMD command. When the target io
request is done, the same IORING_OP_URING_CMD is issued to ublk driver for
both committing io request result and getting future notification of new
io request.
Another thing done by ublk driver is to copy data between kernel io
request and ublksrv's io buffer:
1) before ubsrv handles WRITE request, copy the request's data into
ublksrv's userspace io buffer, so that ublksrv can handle the write
request
2) after ubsrv handles READ request, copy ublksrv's userspace io buffer
into this READ request, then ublk driver can complete the READ request
Zero copy may be switched if mm is ready to support it.
ublk driver doesn't handle any logic of the specific user space driver,
so it is small/simple enough.
[1] ublksrv
https://github.com/ming1/ubdsrv
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220713140711.97356-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a nexthop is added, without a gw address, the default scope was set
to 'host'. Thus, when a source address is selected, 127.0.0.1 may be chosen
but rejected when the route is used.
When using a route without a nexthop id, the scope can be configured in the
route, thus the problem doesn't exist.
To explain more deeply: when a user creates a nexthop, it cannot specify
the scope. To create it, the function nh_create_ipv4() calls fib_check_nh()
with scope set to 0. fib_check_nh() calls fib_check_nh_nongw() wich was
setting scope to 'host'. Then, nh_create_ipv4() calls
fib_info_update_nhc_saddr() with scope set to 'host'. The src addr is
chosen before the route is inserted.
When a 'standard' route (ie without a reference to a nexthop) is added,
fib_create_info() calls fib_info_update_nhc_saddr() with the scope set by
the user. iproute2 set the scope to 'link' by default.
Here is a way to reproduce the problem:
ip netns add foo
ip -n foo link set lo up
ip netns add bar
ip -n bar link set lo up
sleep 1
ip -n foo link add name eth0 type dummy
ip -n foo link set eth0 up
ip -n foo address add 192.168.0.1/24 dev eth0
ip -n foo link add name veth0 type veth peer name veth1 netns bar
ip -n foo link set veth0 up
ip -n bar link set veth1 up
ip -n bar address add 192.168.1.1/32 dev veth1
ip -n bar route add default dev veth1
ip -n foo nexthop add id 1 dev veth0
ip -n foo route add 192.168.1.1 nhid 1
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> RTNETLINK answers: Invalid argument
> $ ip netns exec foo ping -c1 192.168.1.1
> ping: connect: Invalid argument
Try without nexthop group (iproute2 sets scope to 'link' by dflt):
ip -n foo route del 192.168.1.1
ip -n foo route add 192.168.1.1 dev veth0
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> 192.168.1.1 dev veth0 src 192.168.0.1 uid 0
> cache
> $ ip netns exec foo ping -c1 192.168.1.1
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.039 ms
>
> --- 192.168.1.1 ping statistics ---
> 1 packets transmitted, 1 received, 0% packet loss, time 0ms
> rtt min/avg/max/mdev = 0.039/0.039/0.039/0.000 ms
CC: stable@vger.kernel.org
Fixes: 597cfe4fc3 ("nexthop: Add support for IPv4 nexthops")
Reported-by: Edwin Brossette <edwin.brossette@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220713114853.29406-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
