When switching card voltage to UHS voltage the mmc framework tries to
check the card busy signal, meaning the card pulling DAT0 line low,
before the switch is made. Drivers that does not implement the card_busy
function will manage to do the switch anyway, but the framework will
print a warning about not being able to verify the voltage signal.
Implement card_busy function.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20210816142314.1168-1-marten.lindahl@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci use PIO mode, and use mmc_send_tuning() to send the tuning
command, system will stuck because of the storm irq of sdhci. For PIO mode,
use mmc_send_tuning(), it will trigger buffer_read_ready interrupt and data
transfer complete interrupt. In current code logic, it will directly
return in sdhci_data_irq, can not call the sdhci_transfer_pio(). So the
buffer_read_ready interrupt storm happen. So for standard tuning method,
need to exclude this case.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1628858041-1911-1-git-send-email-haibo.chen@nxp.com
[Ulf: Dropped redundant parenthesis in an expression]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CIS tuples in the range 0x80-0x8F are reserved for vendors. Some devices
have tuples in this range which get warned about every boot. Since this
is normal behavior, don't print these tuples unless debug is enabled.
Unfortunately, we cannot use a variable for the format string since it
gets pasted by pr_*_ratelimited.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210726163654.1110969-1-sean.anderson@seco.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc_blk_card_busy() calls card_busy_detect() to poll for the card's
state with CMD13, this is done without any delays in between the commands
being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common __mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-4-ulf.hansson@linaro.org
When __mmc_blk_ioctl_cmd() calls card_busy_detect() to verify that the
card's states moves back into transfer state, the polling with CMD13 is
done without any delays in between the commands being sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-3-ulf.hansson@linaro.org
When mmc_blk_fix_state() sends a CMD12 to try to move the card into the
transfer state, it calls card_busy_detect() to poll for the card's state
with CMD13. This is done without any delays in between the commands being
sent.
Rather than fixing card_busy_detect() in this regards, let's instead
convert into using the common mmc_poll_for_busy(), which also helps us to
avoid open-coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210702134229.357717-2-ulf.hansson@linaro.org
This driver has had problems when handling data errors. Add fault
injection support so that the abort handling can be easily triggered and
regression-tested. A hrtimer is used to indicate a data CRC error at
various points during the data transfer.
Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull powerpc fixes from Michael Ellerman:
- Fix random crashes on some 32-bit CPUs by adding isync() after
locking/unlocking KUEP
- Fix intermittent crashes when loading modules with strict module RWX
- Fix a section mismatch introduce by a previous fix.
Thanks to Christophe Leroy, Fabiano Rosas, Laurent Vivier, Murilo
Opsfelder Araújo, Nathan Chancellor, and Stan Johnson.
h# -----BEGIN PGP SIGNATURE-----
* tag 'powerpc-5.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix set_memory_*() against concurrent accesses
powerpc/32s: Fix random crashes by adding isync() after locking/unlocking KUEP
powerpc/xive: Do not mark xive_request_ipi() as __init
Pull clk driver fixes from Stephen Boyd:
- Make the regulator state match the GDSC power domain state at boot on
Qualcomm SoCs so that the regulator isn't turned off inadvertently.
- Fix earlycon on i.MX6Q SoCs
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gdsc: Ensure regulator init state matches GDSC state
clk: imx6q: fix uart earlycon unwork
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 5.14-rc7.
They consist of:
- revert for an interconnect patch that was found to have problems
- ipack tpci200 driver fixes for reported problems
- slimbus messaging and ngd fixes for reported problems
All are small and have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ipack: tpci200: fix memory leak in the tpci200_register
ipack: tpci200: fix many double free issues in tpci200_pci_probe
slimbus: ngd: reset dma setup during runtime pm
slimbus: ngd: set correct device for pm
slimbus: messaging: check for valid transaction id
slimbus: messaging: start transaction ids from 1 instead of zero
Revert "interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate"
Pull USB fix from Greg KH:
"Here is a single USB typec tcpm fix for a reported problem for
5.14-rc7. It showed up in 5.13 and resolves an issue that Hans found.
It has been in linux-next this week with no reported problems"
* tag 'usb-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Fix VDMs sometimes not being forwarded to alt-mode drivers
Pull RISC-V fixes from Palmer Dabbelt:
- fix the sifive-l2-cache device tree bindings for json-schema
compatibility. This does not change the intended behavior of the
binding.
- avoid improperly freeing necessary resources during early boot.
* tag 'riscv-for-linus-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix a number of free'd resources in init_resources()
dt-bindings: sifive-l2-cache: Fix 'select' matching
Pull s390 fix from Vasily Gorbik:
- fix use after free of zpci_dev in pci code
* tag 's390-5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix use after free of zpci_dev
Pull mandatory file locking deprecation warning from Jeff Layton:
"As discussed on the list, this patch just adds a new warning for folks
who still have mandatory locking enabled and actually mount with '-o
mand'. I'd like to get this in for v5.14 so we can push this out into
stable kernels and hopefully reach folks who have mounts with -o mand.
For now, I'm operating under the assumption that we'll fully remove
this support in v5.15, but we can move that out if any legitimate
users of this facility speak up between now and then"
* tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
fs: warn about impending deprecation of mandatory locks
