Merge series from Ranjani Sridharan <ranjani.sridharan@linux.intel.com>:
This series is continuation of the IPC abstraction in the SOF driver in
preparation for supporting the new IPC supported by the SOF firmware.
It introduces abstraction for top-level IPC ops for sending/receiving
regular and large IPC's.
Peter Ujfalusi (15):
ASoC: SOF: Add helper function to prepare and send an IPC message
ASoC: SOF: Add high level IPC IO callback definitions to ipc_ops
ASoC: SOF: ipc3: Implement the tx_msg IPC ops
ASoC: SOF: ipc3: Use sof_ipc3_tx_msg() internally for message sending
ASoC: SOF: ipc3: Implement the set_get_data IPC ops
ASoC: SOF: ipc3: Implement the get_reply IPC ops
ASoC: SOF: ipc3: Implement rx_msg IPC ops
ASoC: SOF: ipc: Separate the ops checks by functions/topics
ASoC: SOF: ipc: Add check for mandatory IPC message handling ops
ASoC: SOF: ipc: Use the get_reply ops in snd_sof_ipc_get_reply()
ASoC: SOF: ipc: Switch over to use the tx_msg and set_get_data ops
ASoC: SOF: ipc: Switch over to use the rx_msg ops
ASoC: SOF: Add widget_kcontrol_setup control ops for IPC3
ASoC: SOF: sof-audio: Use the widget_kcontrol_setup ops for kcontrol
set up
ASoC: SOF: ipc: Move the ipc_set_get_comp_data() local to ipc3-control
sound/soc/sof/ipc.c | 858 ++---------------------------------
sound/soc/sof/ipc3-control.c | 131 +++++-
sound/soc/sof/ipc3.c | 682 +++++++++++++++++++++++++++-
sound/soc/sof/sof-audio.c | 54 +--
sound/soc/sof/sof-audio.h | 7 +-
sound/soc/sof/sof-priv.h | 28 +-
6 files changed, 880 insertions(+), 880 deletions(-)
--
2.25.1
Merge series from Mario Limonciello <mario.limonciello@amd.com>:
It's not possible to probe for the presence of a DMIC, so the ACP6x
machine driver currently has a hardcoded list of all the systems known
to have a DMIC connected to the ACP.
Although this design works it means that the acp6x driver needs to always
grow with more systems and worse, if an OEM introduces a new system there
will be a mismatch in time that even if the driver (otherwise) works fine
it needs their system added to the list to work.
So this series introduces a _DSD that OEMs can populate into the BIOS to
indicate presence of a DMIC.
sound/soc/tegra/tegra186_asrc.c:90:12: error: ‘tegra186_asrc_runtime_resume’ defined but not used [-Werror=unused-function]
static int tegra186_asrc_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/tegra/tegra186_asrc.c:80:12: error: ‘tegra186_asrc_runtime_suspend’ defined but not used [-Werror=unused-function]
static int tegra186_asrc_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Mark these functions as __maybe_unused to avoid this kind of warning.
Fixes: a2df8c2d5b ("ASoC: tegra: Add Tegra186 based ASRC driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20220411020908.580-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the acp6x machine driver requires a hardcoded list of systems
that physically have DMIC connected.
To avoid having to continually add to an evergrowing list of systems add
support for a _DSD that can advertise this.
OEMs can add this _DSD to their BIOS under the ACP device to automatically
add the device to this driver without requiring any driver modifications.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220411134532.13538-3-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all of the quirked systems use the same card and so the
DMI quirk list doesn't contain driver data.
Add driver data to these quirks and then check the data was present
or not. This will allow potentially setting quirks for systems with
faulty firmware that claims to have a DMIC but doesn't really.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220411134532.13538-2-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Jiaxin Yu <jiaxin.yu@mediatek.com>:
The series reuses mt8192-mt6359-rt1015-rt5682.c for supporting machine
driver with rt1015p speaker amplifier and rt5682s headset codec.
Add support for using the rt5682s codec together with rt1015p on
mt8192-mt6359 machines. All configurations are shared with the rt5682
codec variant, so simply select the SND_SOC_RT5682S config to ensure the
codec is present and set the correct card name. The codec will be linked
to by pointing to it in the headset-codec property in the devicetree.
While at it, also create macros for the names of the different codec
variants supported by this driver, as well as rename occurrences of
rt1015p_rt5682 to rt1015p_rt5682x, since they are shared between rt5682
and rt5682s.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220408060552.26607-5-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Mauro Carvalho Chehab <mchehab@kernel.org>:
Huawei Matebook D15 uses two different GPIOs are used to control the output:
- gpio0 controls the speaker output;
- gpio1 controls the headphone output.
Changing both at the same time cause spurious events that are mis-interpreted
as input events, causing troubles on apps. So, a delay is needed before turning
on such gpios.
Also, the headset microphone is connected to MIC1, instead of MIC2 port.
With this patch, plugging a headphone causes a jack event to trigger the speaker
supply, powering down the speaker and powering up the headphone output.
Removing the headphone also triggers the power supply, powering up the speaker
and powering down the headphone.
The headset microphone also works.
When the driver fails during probing, the driver should disable the
regulator, not just handle it in wm8731_hw_init().
The following log reveals it:
[ 17.812483] WARNING: CPU: 1 PID: 364 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0
[ 17.815958] RIP: 0010:_regulator_put+0x3ec/0x4e0
[ 17.824467] Call Trace:
[ 17.824774] <TASK>
[ 17.825040] regulator_bulk_free+0x82/0xe0
[ 17.825514] devres_release_group+0x319/0x3d0
[ 17.825882] i2c_device_probe+0x766/0x940
[ 17.829198] i2c_register_driver+0xb5/0x130
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220405121038.4094051-1-zheyuma97@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SIDO(Single-Inductor Dual-Ouput) Buck powers up both analog and digital
circuits along with internal memory, powering off this is the last thing
that codec should do when going to very low power.
Current code was powering off this Buck if there are no users of sysclk,
which is not correct. Powering off this buck will result in no register access.
This code path was never tested until recently after adding pm support
in SoundWire controller. Fix this by removing the buck poweroff when the
codec is active and also the code that is not used.
Without this patch all the read/write transactions will never complete and
results in SLIMBus Errors like:
qcom,slim-ngd qcom,slim-ngd.1: Tx:MT:0x0, MC:0x60, LA:0xcf failed:-110
wcd934x-codec wcd934x-codec.1.auto: ASoC: error at soc_component_read_no_lock
on wcd934x-codec.1.auto for register: [0x00000d05] -110
qcom,slim-ngd-ctrl 171c0000.slim: Error Interrupt received 0x82000000
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Fixes: a61f3b4f47 ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20220407094313.2880-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch takes a defensive programming and paranoid approach in case
the parent device (SoundWire) is pm_runtime resumed but the rt711
device is not. In that case, during the attachment and initialization,
a jack detection workqueue can be scheduled. Since the pm_runtime
suspend routines will not be invoked, the sequence to cancel all
deferred work is not executed, and the jack detection could happen
after the bus stops operating, leading to a timeout.
This patch applies the same solution to rt5682, based on the
similarities between codec drivers. The race condition with rt5682 was
not detected experimentally though.
BugLink: https://github.com/thesofproject/linux/issues/3459
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220406192005.262996-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
This avoids scanning the identifier tables during probes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220405163618.2158090-1-steve@sk2.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
This avoids scanning the identifier tables during probes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220405130326.2107293-1-steve@sk2.org
Signed-off-by: Mark Brown <broonie@kernel.org>
