When CONFIG_COMMON_CLK is disabled, e.g. on an x86 randconfig compile test,
clang reports a field overflow from propagating the result of a division by
zero:
drivers/leds/leds-sun50i-a100.c:309:12: error: call to '__compiletime_assert_265' declared with 'error' attribute: FIELD_PREP: value too large for the field
control = FIELD_PREP(LEDC_T01_TIMING_CTRL_REG_T1H, timing->t1h_ns / cycle_ns) |
Avoid the problem by adding an explicit check for the zero value here. Alternatively
the assertion could be avoided with a Kconfig dependency on COMMON_CLK.
Fixes: 090a25ad9798 ("leds: sun50i-a100: New driver for the A100 LED controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20231212214536.175327-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
In case leds-gpio fails to get at least one of possibly many GPIOs
from the DT (e.g. the GPIO is already requested) neither gpiolib nor
the driver does provide any helpful error log:
leds-gpio: probe of leds failed with error -16
As the driver knows better how to handle errors with such mandatory
GPIOs, let's implement an error log which points to the affected
GPIO.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231202183636.7055-1-wahrenst@gmx.net
Signed-off-by: Lee Jones <lee@kernel.org>
AW200XX controllers have the capability to declare more than 0xf LEDs,
therefore, it is necessary to accept LED names using an appropriate
regex pattern.
The register offsets can be adjusted within the specified range, with
the maximum value corresponding to the highest number of LEDs that can
be connected to the controller.
Fixes: e338a05e76 ("dt-bindings: leds: Add binding for AW200xx")
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231125200519.1750-12-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
HWEN is hardware control, which is used for enable/disable aw200xx chip.
It's high active, internally pulled down to GND.
After HWEN pin set high the chip begins to load the OTP information,
which takes 200us to complete. About 200us wait time is needed for
internal oscillator startup and display SRAM initialization. After
display SRAM initialization, the registers in page 1 to page 5 can be
configured via i2c interface.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Link: https://lore.kernel.org/r/20231125200519.1750-3-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
The serial tty interface also supports additional input signals, that
can also be evaluated within this trigger. This change is adding the
following additional input sources, which could be controlled
via the '/sys/class/<leds>/' sysfs interface.
Explanation:
DCE = Data Communication Equipment (Modem)
DTE = Data Terminal Equipment (Computer)
- cts:
DCE is ready to accept data from the DTE (CTS = Clear To Send). If
the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate CTS.
If set to 1, the LED will evaluate CTS.
- dsr:
DCE is ready to receive and send data (DSR = Data Set Ready). If the
line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DSR.
If set to 1, the LED will evaluate DSR.
- dcd:
DTE is receiving a carrier from the DCE (DCD = Data Carrier Detect).
If the line state is detected, the LED is switched on.
If set to 0 (default), the LED will not evaluate DCD.
If set to 1, the LED will evaluate DCD.
- rng:
DCE has detected an incoming ring signal on the telephone line
(RNG = Ring Indicator). If the line state is detected, the LED is
switched on.
If set to 0 (default), the LED will not evaluate RNG.
If set to 1, the LED will evaluate RNG.
Also add an invert flag on LED blink, so that the LED blinks in the
correct order.
* If one off the new enabled input signals are evaluatet as 'enabled',
and data are transmitted, then the LED should first blink 'off' and
then 'on' (invert).
* If all the new enabled input signals are evaluatet as 'disabled',
and data are transmitted, then the LED should first blink 'on' and
then 'off'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Maarten Brock <m.brock@vanmierlo.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-5-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Until now, the LED blinks when data is sent via the tty (rx/tx).
This is not configurable.
This change adds the possibility to make the indication for the direction
of the transmitted data independently controllable via the new rx and
tx sysfs entries.
- rx:
Signal reception (rx) of data on the named tty device.
If set to 0, the LED will not blink on reception.
If set to 1 (default), the LED will blink on reception.
- tx:
Signal transmission (tx) of data on the named tty device.
If set to 0, the LED will not blink on transmission.
If set to 1 (default), the LED will blink on transmission.
This new sysfs entry are on by default. Thus the trigger behaves as
before this change.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-4-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
With this commit, the mutex handling is replaced by the completion
handling. When handling mutex, it must always be ensured that the held
mutex is also released again. This is more error-prone should the number
of code paths increase.
This is a preparatory commit to make the trigger more configurable via
additional sysfs parameters. With this change, the worker always runs and
is no longer stopped if no ttyname is set.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-3-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
There is no in-kernel function to get the status register of a tty device
like the TIOCMGET ioctl returns to userspace. Create a new function,
tty_get_tiocm(), to obtain the status register that other portions of the
kernel can call if they need this information, and move the existing
internal tty_tiocmget() function to use this interface.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20231127110311.3583957-2-fe@dev.tdt.de
Signed-off-by: Lee Jones <lee@kernel.org>
Pull parisc architecture fixes from Helge Deller:
- Include the upper 5 address bits when inserting TLB entries on a
64-bit kernel.
On physical machines those are ignored, but in qemu it's nice to have
them included and to be correct.
- Stop the 64-bit kernel and show a warning if someone tries to boot on
a machine with a 32-bit CPU
- Fix a "no previous prototype" warning in parport-gsc
* tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent booting 64-bit kernels on PA1.x machines
parport: gsc: mark init function static
parisc/pgtable: Do not drop upper 5 address bits of physical address
Pull LoongArch updates from Huacai Chen:
- support PREEMPT_DYNAMIC with static keys
- relax memory ordering for atomic operations
- support BPF CPU v4 instructions for LoongArch
- some build and runtime warning fixes
* tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
selftests/bpf: Enable cpu v4 tests for LoongArch
LoongArch: BPF: Support signed mod instructions
LoongArch: BPF: Support signed div instructions
LoongArch: BPF: Support 32-bit offset jmp instructions
LoongArch: BPF: Support unconditional bswap instructions
LoongArch: BPF: Support sign-extension mov instructions
LoongArch: BPF: Support sign-extension load instructions
LoongArch: Add more instruction opcodes and emit_* helpers
LoongArch/smp: Call rcutree_report_cpu_starting() earlier
LoongArch: Relax memory ordering for atomic operations
LoongArch: Mark __percpu functions as always inline
LoongArch: Disable module from accessing external data directly
LoongArch: Support PREEMPT_DYNAMIC with static keys
Pull powerpc fixes from Michael Ellerman:
- Finish a refactor of pgprot_framebuffer() which dependend
on some changes that were merged via the drm tree
- Fix some kernel-doc warnings to quieten the bots
Thanks to Nathan Lynch and Thomas Zimmermann.
* tag 'powerpc-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/rtas: Fix ppc_rtas_rmo_buf_show() kernel-doc
powerpc/pseries/rtas-work-area: Fix rtas_work_area_reserve_arena() kernel-doc
powerpc/fb: Call internal __phys_mem_access_prot() in fbdev code
powerpc: Remove file parameter from phys_mem_access_prot()
powerpc/machdep: Remove trailing whitespaces
Pull smb client fixes from Steve French:
- ctime caching fix (for setxattr)
- encryption fix
- DNS resolver mount fix
- debugging improvements
- multichannel fixes including cases where server stops or starts
supporting multichannel after mount
- reconnect fix
- minor cleanups
* tag '6.7-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number for cifs.ko
cifs: handle when server stops supporting multichannel
cifs: handle when server starts supporting multichannel
Missing field not being returned in ioctl CIFS_IOC_GET_MNT_INFO
smb3: allow dumping session and tcon id to improve stats analysis and debugging
smb: client: fix mount when dns_resolver key is not available
smb3: fix caching of ctime on setxattr
smb3: minor cleanup of session handling code
cifs: reconnect work should have reference on server struct
cifs: do not pass cifs_sb when trying to add channels
cifs: account for primary channel in the interface list
cifs: distribute channels across interfaces based on speed
cifs: handle cases where a channel is closed
smb3: more minor cleanups for session handling routines
smb3: minor RDMA cleanup
cifs: Fix encryption of cleared, but unset rq_iter data buffers
Pull probes fixes from Masami Hiramatsu:
- Documentation update: Add a note about argument and return value
fetching is the best effort because it depends on the type.
- objpool: Fix to make internal global variables static in
test_objpool.c.
- kprobes: Unify kprobes_exceptions_nofify() prototypes. There are the
same prototypes in asm/kprobes.h for some architectures, but some of
them are missing the prototype and it causes a warning. So move the
prototype into linux/kprobes.h.
- tracing: Fix to check the tracepoint event and return event at
parsing stage. The tracepoint event doesn't support %return but if
$retval exists, it will be converted to %return silently. This finds
that case and rejects it.
- tracing: Fix the order of the descriptions about the parameters of
__kprobe_event_gen_cmd_start() to be consistent with the argument
list of the function.
* tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/kprobes: Fix the order of argument descriptions
tracing: fprobe-event: Fix to check tracepoint event and return
kprobes: unify kprobes_exceptions_nofify() prototypes
lib: test_objpool: make global variables static
Documentation: tracing: Add a note about argument and retval access
