If the do while loop breaks in 'if (!sg_dma_len(sgl))' in the first
iteration, err is uninitialized causing a wrong call to zap_vma_ptes().
But that is impossible to happen as a scatterlist must have at least
one valid segment.
Anyways to avoid more reports from static checkers initializing ret
here.
Fixes: b12d691ea5 ("i915: fix remap_io_sg to verify the pgprot")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517202117.179303-1-jose.souza@intel.com
XE_LPD continues to use the same "skylake-style" watermark
programming as other recent platforms. The only change to the watermark
calculations compared to Display12 is that XE_LPD now allows a
maximum of 255 lines vs the old limit of 31.
Due to the larger possible lines value, the corresponding bits
representing the value in PLANE_WM are also extended, so make sure we
read/write enough bits. Let's also take this opportunity to switch over
to the REG_FIELD notation.
Bspec: 49325
Bspec: 50419
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-3-matthew.d.roper@intel.com
The DDI naming template for display version 12 went A-C, TC1-TC6. With
XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4.
The XE_LPD design keeps the register offsets and bitfields relating to
the TC outputs in the same location they were previously. The new "D"
and "E" outputs now take the locations that were previously used by TC5
and TC6 outputs, or what we would have considered to be outputs "H" and
"I" under the legacy lettering scheme.
For the most part everything will just work as long as we initialize the
output with the proper 'enum port' value. However we do need to take
care to pick the correct AUX channel when parsing the VBT (e.g., a
reference to 'AUX D' is actually asking us to use the 8th aux channel,
not the fourth). We should also make sure that our encoders and aux
channels are named appropriately so that it's easier to correlate driver
debug messages with the bspec instructions.
v2:
- Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose)
v3:
- Add hpd_pin to handle outputs D and E (Jose)
- Fixed conversion of BIOS port to aux ch for TC ports (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-2-matthew.d.roper@intel.com
Aside from the hardware-managed PG0, XE_LPD has power wells 1-2 and
A-D. These power wells should be enabled/disabled according to the
following dependency tree (enable top to bottom, disable bottom to top):
PG0
|
--PG1--
/ \
PGA --PG2--
/ | \
PGB PGC PGD
PWR_WELL_CTL follows the general ICL/TGL design and places PG A-D in the
bits that would have been PG 6-9 under the old scheme.
PWR_WELL_CTL_{DDI,AUX}'s bit indexing for DDI's A-C and TC1 is the same
as TGL, but DDI-D is placed at index 7 (bits 14 & 15).
v2:
- Squash in LPSP status patch from Uma since it's also a
powerwell-specific change.
Bspec: 49233
Bspec: 49503
Bspec: 49504
Bspec: 49505
Bspec: 49296
Bspec: 50090
Bspec: 53920
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-4-matthew.d.roper@intel.com
When encoder validation of a display mode fails, retry with less bandwidth
heavy YCbCr420 color mode, if available. This enables some HDMI 1.4 setups
to support 4k60Hz output, which previously failed silently.
AMDGPU had nearly the exact same issue. This problem description is
therefore copied from my commit message of the AMDGPU patch.
On some setups, while the monitor and the gpu support display modes with
pixel clocks of up to 600MHz, the link encoder might not. This prevents
YCbCr444 and RGB encoding for 4k60Hz, but YCbCr420 encoding might still be
possible. However, which color mode is used is decided before the link
encoder capabilities are checked. This patch fixes the problem by retrying
to find a display mode with YCbCr420 enforced and using it, if it is
valid.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210510133349.14491-4-wse@tuxedocomputers.com
Couples the decission between RGB and YCbCr420 mode and the check if the
port clock can archive the required frequency. Other checks and
configuration steps that where previously done in between can also be done
before or after.
This allows for are cleaner implementation of retrying different color
encodings.
A slight change in behaviour occurs with this patch: If YCbCr420 is not
allowed but display is YCbCr420 only it no longer fails, but just prints
an error and tries to fallback on RGB.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210510133349.14491-3-wse@tuxedocomputers.com
Direction on gen9+ was to stop reading the straps and only rely on the
VBT for marking the port presence. This happened while dealing with
WaIgnoreDDIAStrap and instead of using it as a WA, it should now be the
normal flow. See commit 885d3e5b6f ("drm/i915/display: fix comment on
skl straps").
For gen 10 it's hard to say if this will work or not since I can't test
it, so leave it with the same behavior as before.
For PCH_TGP we should still rely on the VBT to make ports E and F not
available.
v2 (Ville):
- use display ver >= 9 to make it consistent with the rest of the
driver instead of checking for == 9
- also handle CNL and only initialize port F if it is
IS_CNL_WITH_PORT_F. Eventually CNL may be removed, but while it
isn't let's keep it consistent everywhere
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430223808.1078010-4-lucas.demarchi@intel.com
Since commit 45c0673aac ("drm/i915/bios: start using the
intel_bios_encoder_data directly") we lookup the devdata for each port
in intel_ddi_init() and just return if the port is not present in VBT
(or if we didn't create a fake devdata for it if VBT is not available).
So in intel_display.c we don't have to check
intel_bios_is_port_present(), just rely on the check in
intel_ddi_init().
v2: Rebase on commit 45c0673aac ("drm/i915/bios: start using the
intel_bios_encoder_data directly") re-using that check in intel_ddi_init()
instead of adding a new one.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430223808.1078010-2-lucas.demarchi@intel.com
Commit b9d79e4ca4 ("fbmem: Mark proc_fb_seq_ops as __maybe_unused")
places the '__maybe_unused' in an entirely incorrect location between
the "struct" keyword and the structure name.
It's a wonder that gcc accepts that silently, but clang quite reasonably
warns about it:
drivers/video/fbdev/core/fbmem.c:736:21: warning: attribute declaration must precede definition [-Wignored-attributes]
static const struct __maybe_unused seq_operations proc_fb_seq_ops = {
^
Fix it.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm fixes from Dave Airlie:
"Bit later than usual, I queued them all up on Friday then promptly
forgot to write the pull request email. This is mainly amdgpu fixes,
with some radeon/msm/fbdev and one i915 gvt fix thrown in.
amdgpu:
- MPO hang workaround
- Fix for concurrent VM flushes on vega/navi
- dcefclk is not adjustable on navi1x and newer
- MST HPD debugfs fix
- Suspend/resumes fixes
- Register VGA clients late in case driver fails to load
- Fix GEM leak in user framebuffer create
- Add support for polaris12 with 32 bit memory interface
- Fix duplicate cursor issue when using overlay
- Fix corruption with tiled surfaces on VCN3
- Add BO size and stride check to fix BO size verification
radeon:
- Fix off-by-one in power state parsing
- Fix possible memory leak in power state parsing
msm:
- NULL ptr dereference fix
fbdev:
- procfs disabled warning fix
i915:
- gvt: Fix a possible division by zero in vgpu display rate
calculation"
* tag 'drm-next-2021-05-10' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: Use device specific BO size & stride check.
drm/amdgpu: Init GFX10_ADDR_CONFIG for VCN v3 in DPG mode.
drm/amd/pm: initialize variable
drm/radeon: Avoid power table parsing memory leaks
drm/radeon: Fix off-by-one power_state index heap overwrite
drm/amd/display: Fix two cursor duplication when using overlay
drm/amdgpu: add new MC firmware for Polaris12 32bit ASIC
fbmem: Mark proc_fb_seq_ops as __maybe_unused
drm/msm/dpu: Delete bonkers code
drm/i915/gvt: Prevent divided by zero when calculating refresh rate
amdgpu: fix GEM obj leak in amdgpu_display_user_framebuffer_create
drm/amdgpu: Register VGA clients after init can no longer fail
drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown
drm/amdgpu: fix r initial values
drm/amd/display: fix wrong statement in mst hpd debugfs
amdgpu/pm: set pp_dpm_dcefclk to readonly on NAVI10 and newer gpus
amdgpu/pm: Prevent force of DCEFCLK on NAVI10 and SIENNA_CICHLID
drm/amdgpu: fix concurrent VM flushes on Vega/Navi v2
drm/amd/display: Reject non-zero src_y and src_x for video planes
Pull block fix from Jens Axboe:
"Turns out the bio max size change still has issues, so let's get it
reverted for 5.13-rc1. We'll shake out the issues there and defer it
to 5.14 instead"
* tag 'block-5.13-2021-05-09' of git://git.kernel.dk/linux-block:
Revert "bio: limit bio max size"
Pull cifs fixes from Steve French:
"Three small SMB3 chmultichannel related changesets (also for stable)
from the SMB3 test event this week.
The other fixes are still in review/testing"
* tag '5.13-rc-smb3-part3' of git://git.samba.org/sfrench/cifs-2.6:
smb3: if max_channels set to more than one channel request multichannel
smb3: do not attempt multichannel to server which does not support it
smb3: when mounting with multichannel include it in requested capabilities
