This patch reworks the SPI access and fixes several probems:
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Do not place variable "addr" on stack and use it as buffer for SPI
transfer. Buffers for SPI transfers must be allocated from DMA save
memory.
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Halfe number of SPI transfers by using a single buffer + memcpy().
This improves the performance, especially on SPI controllers, which
use interrupt based transfers.
- Use "8" bits per word, not "32". This makes it possible to use this
driver on SoCs like the Raspberry Pi, which SPI host controller
drivers only support 8 bits per word.
Note: this breaks half duplex only controllers. Support for them will be
re-added in the next patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-16-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marek Vasut says:
====================
net: ks8851: Add KS8851 PHY support
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, except the PHY ID Low/High registers are swapped.
Register MDIO bus so this PHY can be detected and probed by phylib.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because macvlan_common_newlink() and macvlan_changelink() already
checked NULL data parameter, so the additional check is unnecessary,
just remove it.
Fixes: 79cf79abce ("macvlan: add source mode")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports 8 RSS groups per interface. Currently we are using
only group '0'. This patch allows user to create new RSS groups/contexts
and use the same as destination for flow steering rules.
usage:
To steer the traffic to RQ 2,3
ethtool -X eth0 weight 0 0 1 1 context new
(It will print the allocated context id number)
New RSS context is 1
ethtool -N eth0 flow-type tcp4 dst-port 80 context 1 loc 1
To delete the context
ethtool -X eth0 context 1 delete
When an RSS context is removed, the active classification
rules using this context are also removed.
Change-log:
v4
- Fixed compiletime warning.
- Address Saeed's comments on v3.
v3
- Coverted otx2_set_rxfh() to use new function.
v2
- Removed unrelated whitespace
- Coverted otx2_get_rxfh() to use new function.
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a NCI command in work queue after closing the NCI device at
nci_unregister_device, The NCI command timer starts at flush_workqueue
function and then NCI command timeout handler would be called 5 second
after flushing the NCI command work queue and destroying the queue.
At that time, the timeout handler would try to use NCI command work queue
that is destroyed already. it will causes the problem. To avoid this
abnormal situation, change the sequence to prevent the NCI command timeout
handler from being called after destroying the NCI command work queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sockfd_lookup uses fget on the value that is stored in
the file field of the returned structure, so fput should ultimately be
applied to this value. This can be done directly, but it seems better
to use the specific macro sockfd_put, which does the same thing.
Perform a source code refactoring by using the following semantic patch.
// <smpl>
@@
expression s;
@@
s = sockfd_lookup(...)
...
+ sockfd_put(s);
- fput(s->file);
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2021-01-05
SW steering, Refactor to have a device specific STE layer below dr_ste
This series introduces some improvements and refactoring by adding a new layer
below dr_ste to allow support for different devices format.
It adds a struct of device specific callbacks for STE layer below dr_ste.
Each device will implement its HW-specific function, and a common logic
from the DR code will access these functions through the new ste_ctx API.
Connect-X5-style steering format is called STE_v0.
In the next patch series we bring the Connect-X6-style format - STE_v1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The simple_strtol() function is deprecated, use simple_strtoul() instead.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MHI net is protocol agnostic, the payload protocol depends on the modem
configuration, which can be either RMNET (IP muxing and aggregation) or
raw IP. This patch adds support for incomming IPv4/IPv6 packets, that
was previously unconditionnaly reported as RMNET packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle says:
====================
enetc: code cleanups
This are some code cleanups in the MDIO part of the enetc. They are
intended to make the code more readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there aren't any more macros with parameters, move the macros
above any functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro enetc_mdio_rd_reg() is just used in that particular case and
has a hardcoded parameter name "mdio_priv". Define a specific function
to use for readx_poll_timeout() instead. Also drop the TIMEOUT macro
since it is used just once.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 6517798dd3 ("enetc: Make MDIO accessors more generic and
export to include/linux/fsl") these macros actually had some benefits.
But after the commit it just makes the code hard to read. Drop the macro
indirections.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move HW specific modify header fields and logic to STEv0 file
and use the new STE context callbacks.
Since STEv0 and STEv1 modify actions values are different, each
version has its own implementation.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use STE tx/rx actions per-device API: move HW specific
action apply logic from dr_ste to STEv0 file - STEv0 and
STEv1 actions format is different, each version should
have its own implementation.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use the new setters and getters API for STEv0: move HW specific setter and
getters from dr_ste to STEv0 file. Since STEv0 and STEv1 format are
different each version should implemented different setters and getters.
Rename remaining static functions w/o mlx5 prefix.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The action apply logic is device specific per STE version,
moving to the STE layer will allow implementing it for
both devices while keeping DR upper layers the same.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
