Some powers were changed during the jack insert detection and clk's
enable/disable in CCF.
If in parallel, the influence has a chance to detect the wrong jack
type.
We refer to the below commit of the variant codec (rt5682) to fix
this issue.
ASoC: rt5682: Fix deadlock on resume
1. Remove rt5682s_headset_detect in rt5682s_jd_check_handler and
use jack_detect_work instead of.
2. Use dapm mutex used in CCF to protect most of jack_detect_work.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20220223101450.4577-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
set "HPH Type" Kcontrol max value of WCD_MBHC_HPH_STEREO instead of UINT_MAX.
set "HPHL/R Impedance" Kcontrols max value to INT_MAX instead of UINT_MAX as
max field is integer type.
Without this patch amixer for these controls will show -1 as max value to userspace.
Fixes: bcee7ed09b ("ASoC: codecs: wcd938x: add Multi Button Headset Control support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220222183212.11580-8-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the following error messages are seen during boot:
asoc-simple-card sound: control 2:0:0:SPDIF Switch:0 is already present
cs4265 1-004f: ASoC: failed to add widget SPDIF dapm kcontrol SPDIF Switch: -16
Quoting Mark Brown:
"The driver is just plain buggy, it defines both a regular SPIDF Switch
control and a SND_SOC_DAPM_SWITCH() called SPDIF both of which will
create an identically named control, it can never have loaded without
error. One or both of those has to be renamed or they need to be
merged into one thing."
Fix the duplicated control name by combining the two SPDIF controls here
and move the register bits onto the DAPM widget and have DAPM control them.
Fixes: f853d6b3ba ("ASoC: cs4265: Add a S/PDIF enable switch")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220215120514.1760628-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When parsing the compressed stream the whole buffer descriptor is
now read in a single cs_dsp_coeff_read_ctrl; on older firmwares
this descriptor is just 4 bytes but on more modern firmwares it is
24 bytes. The current code reads the full 24 bytes regardless, this
was working but reading junk for the last 20 bytes. However commit
f444da38ac ("firmware: cs_dsp: Add offset to cs_dsp read/write")
added a size check into cs_dsp_coeff_read_ctrl, causing the older
firmwares to now return an error.
Update the code to only read the amount of data appropriate for
the firmware loaded.
Fixes: 04ae085967 ("ASoC: wm_adsp: Switch to using wm_coeff_read_ctrl for compressed buffers")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220210172053.22782-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit da0363f7bf ("ASoC: qcom: Fix for DMA interrupt clear reg
overwriting") we changed regmap_write() to regmap_update_bits() so that
we can avoid overwriting bits that we didn't intend to modify.
Unfortunately this change breaks the case where a register is writable
but not readable, which is exactly how the HDMI irq clear register is
designed (grep around LPASS_HDMITX_APP_IRQCLEAR_REG to see how it's
write only). That's because regmap_update_bits() tries to read the
register from the hardware and if it isn't readable it looks in the
regmap cache to see what was written there last time to compare against
what we want to write there. Eventually, we're unable to modify this
register at all because the bits that we're trying to set are already
set in the cache.
This is doubly bad for the irq clear register because you have to write
the bit to clear an interrupt. Given the irq is level triggered, we see
an interrupt storm upon plugging in an HDMI cable and starting audio
playback. The irq storm is so great that performance degrades
significantly, leading to CPU soft lockups.
Fix it by using regmap_write_bits() so that we really do write the bits
in the clear register that we want to. This brings the number of irqs
handled by lpass_dma_interrupt_handler() down from ~150k/sec to ~10/sec.
Fixes: da0363f7bf ("ASoC: qcom: Fix for DMA interrupt clear reg overwriting")
Cc: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220209232520.4017634-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The current rt5682_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current rt5668_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current rt5682s_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.
This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.
Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 9de2b9286a ("ASoC: mediatek: Check for error clk
pointer").
With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.
An analysis of the code with this patch applied shows:
ret = init_clks(pdev, clk);
if (ret)
return ERR_PTR(ret);
...
for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
struct clk *c = clk[data->clk_id[j]];
if (IS_ERR(c)) {
dev_err(&pdev->dev, "%s: clk unavailable\n",
data->name);
return ERR_CAST(c);
}
scpd->clk[j] = c;
}
Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a ("ASoC:
mediatek: Check for error clk pointer") needs to be reverted.
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: Mark Brown <broonie@kernel.org>
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Daniel Golle <daniel@makrotopia.org>
Fixes: 9de2b9286a ("ASoC: mediatek: Check for error clk pointer")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220207160923.3911501-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Mark Brown <broonie@kernel.org>:
The event generation coverage I just wrote shows that the generic ASoC
ops fail to generate events for stereo controls when only the first
channel is changed, we just return the status for the second channel and
discard that for the first.
The controls allow inputs to be specified as negative but our manipulating
them into register fields need to be done on unsigned variables so the
checks for negative numbers weren't taking effect properly. Do the checks
for negative values on the variable in the ABI struct rather than on our
local unsigned copy.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220128192443.3504823-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Takashi Iwai <tiwai@suse.de>:
This is the revised patches for addressing ASoC lockdep warnings due
to the recent DPCM locking refactoring.
On resume from suspend the following chain of events can happen:
A rt5682_resume() -> mod_delayed_work() for jack_detect_work
B DAPM sequence starts ( DAPM is locked now)
A1. rt5682_jack_detect_handler() scheduled
- Takes both jdet_mutex and calibrate_mutex
- Calls in to rt5682_headset_detect() which tries to take DAPM lock, it
starts to wait for it as B path took it already.
B1. DAPM sequence reaches the "HP Amp", rt5682_hp_event() tries to take
the jdet_mutex, but it is locked in A1, so it waits.
Deadlock.
To solve the deadlock, drop the jdet_mutex, use the jack_detect_work to do
the jack removal handling, move the dapm lock up one level to protect the
most of the rt5682_jack_detect_handler(), but not the jack reporting as it
might trigger a DAPM sequence.
The rt5682_headset_detect() can be changed to static as well.
Fixes: 8deb34a90f ("ASoC: rt5682: fix the wrong jack type detected")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220126100325.16513-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent fix for DPCM locking also covered the loop in
dpcm_be_disconnect() with the FE stream lock. This caused an
unexpected side effect, thought: calling debugfs_remove_recursive() in
the spinlock may lead to lockdep splats as the code there assumes the
SOFTIRQ-safe context.
For avoiding the problem, this patch changes the disconnection
procedure to two phases: at first, the matching entries are removed
from the linked list, then the resources are freed outside the lock.
Fixes: b7898396f4 ("ASoC: soc-pcm: Fix and cleanup DPCM locking")
Reported-and-tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220119155249.26754-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Its possible that the sound card is just opened and closed without actually
playing stream, ex: if the audio file itself is missing.
Even in such cases we do call stop on graphs that are not yet started.
DSP can throw errors in such cases, so add a check to see if the graph
was started before stopping it.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mixer controls have the channel id in mixer->reg, which is not same
as port id. port id should be derived from chan_info array.
So fix this. Without this, its possible that we could corrupt
struct wcd938x_sdw_priv by accessing port_map array out of range
with channel id instead of port id.
Fixes: e8ba1e05bd ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We're setting wrong card codec conf for rt1019 amp devices in our
machine driver. Due to this left and right amp channels data are
reversed in our machines as wrong device prefix results in wrong
value for "Mono LR Select" rt1019 mixer control. Reverse dev ids
in codec conf with Left and Right name_prefix to fix such issue.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20220120133605.476138-1-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When SND_SOC_MT8195_MT6359_RT1011_RT5682 is selected,
and GPIOLIB is not selected,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for SND_SOC_DMIC
Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && GPIOLIB [=n]
Selected by [y]:
- SND_SOC_MT8195_MT6359_RT1011_RT5682 [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && I2C [=y] && SND_SOC_MT8195 [=y] && MTK_PMIC_WRAP [=y]
This is because SND_SOC_MT8195_MT6359_RT1011_RT5682
selects SND_SOC_DMIC without selecting or depending on
GPIOLIB, depsite SND_SOC_DMIC depending on GPIOLIB.
This unmet dependency bug was detected by Kismet,
a static analysis tool for Kconfig. Please advise
if this is not the appropriate solution.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20220117050324.68371-1-julianbraha@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
