The stmmac platform drivers that do not open-code the clk_ptp_rate value
after having retrieved the default one from the device-tree can end up
with 0 in clk_ptp_rate (as clk_get_rate can return 0). It will
eventually propagate up to PTP initialization when bringing up the
interface, leading to a divide by 0:
Division by zero in kernel.
CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.30-00001-g48313bd5768a #22
Hardware name: STM32 (Device Tree Support)
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x6c/0x8c
dump_stack_lvl from Ldiv0_64+0x8/0x18
Ldiv0_64 from stmmac_init_tstamp_counter+0x190/0x1a4
stmmac_init_tstamp_counter from stmmac_hw_setup+0xc1c/0x111c
stmmac_hw_setup from __stmmac_open+0x18c/0x434
__stmmac_open from stmmac_open+0x3c/0xbc
stmmac_open from __dev_open+0xf4/0x1ac
__dev_open from __dev_change_flags+0x1cc/0x224
__dev_change_flags from dev_change_flags+0x24/0x60
dev_change_flags from ip_auto_config+0x2e8/0x11a0
ip_auto_config from do_one_initcall+0x84/0x33c
do_one_initcall from kernel_init_freeable+0x1b8/0x214
kernel_init_freeable from kernel_init+0x24/0x140
kernel_init from ret_from_fork+0x14/0x28
Exception stack(0xe0815fb0 to 0xe0815ff8)
Prevent this division by 0 by adding an explicit check and error log
about the actual issue. While at it, remove the same check from
stmmac_ptp_register, which then becomes duplicate
Fixes: 19d857c903 ("stmmac: Fix calculations for ptp counters when clock input = 50Mhz.")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-1-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MANA driver's probe registers netdevice via the following call chain:
mana_probe()
register_netdev()
register_netdevice()
register_netdevice() calls notifier callback for netvsc driver,
holding the netdev mutex via netdev_lock_ops().
Further this netvsc notifier callback end up attempting to acquire the
same lock again in dev_xdp_propagate() leading to deadlock.
netvsc_netdev_event()
netvsc_vf_setxdp()
dev_xdp_propagate()
This deadlock was not observed so far because net_shaper_ops was never set,
and thus the lock was effectively a no-op in this case. Fix this by using
netif_xdp_propagate() instead of dev_xdp_propagate() to avoid recursive
locking in this path.
And, since no deadlock is observed on the other path which is via
netvsc_probe, add the lock exclusivly for that path.
Also, clean up the unregistration path by removing the unnecessary call to
netvsc_vf_setxdp(), since unregister_netdevice_many_notify() already
performs this cleanup via dev_xdp_uninstall().
Fixes: 97246d6d21 ("net: hold netdev instance lock during ndo_bpf")
Cc: stable@vger.kernel.org
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Tested-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1748513910-23963-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_qca: move the SoC type check to the right place
- MGMT: reject malformed HCI_CMD_SYNC commands
- btnxpuart: Fix missing devm_request_irq() return value check
- L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
* tag 'for-net-2025-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
Bluetooth: hci_qca: move the SoC type check to the right place
Bluetooth: btnxpuart: Fix missing devm_request_irq() return value check
Bluetooth: MGMT: reject malformed HCI_CMD_SYNC commands
====================
Link: https://patch.msgid.link/20250530174835.405726-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d2 ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return value of devm_request_irq() must be checked (function is even
annotated) and without it clang W=1 complains:
btnxpuart.c:494:6: error: unused variable 'ret' [-Werror,-Wunused-variable]
Setting up wakeup IRQ handler is not really critical, because the
handler is empty, so just log the informational message so user could
submit proper bug report and silences the clang warning.
Fixes: c50b56664e ("Bluetooth: btnxpuart: Implement host-wakeup feature")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In 'mgmt_hci_cmd_sync()', check whether the size of parameters passed
in 'struct mgmt_cp_hci_cmd_sync' matches the total size of the data
(i.e. 'sizeof(struct mgmt_cp_hci_cmd_sync)' plus trailing bytes).
Otherwise, large invalid 'params_len' will cause 'hci_cmd_sync_alloc()'
to do 'skb_put_data()' from an area beyond the one actually passed to
'mgmt_hci_cmd_sync()'.
Reported-by: syzbot+5fe2d5bfbfbec0b675a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5fe2d5bfbfbec0b675a0
Fixes: 827af4787e ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If we sanitize error returns, the debug statements need
to come before that so that we don't lose information.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 405b0d6107 ("net: usb: aqc111: fix error handling of usbnet read calls")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: 6d2c186afa ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250528093619.3738998-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Marc Kleine-Budde says:
====================
pull-request: can 2025-05-29
this is a pull request of 1 patch for net/main.
The patch is by Fedor Pchelkin and fixes a slab-out-of-bounds access
in the kvaser_pciefd driver.
linux-can-fixes-for-6.16-20250529
* tag 'linux-can-fixes-for-6.16-20250529' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: kvaser_pciefd: refine error prone echo_skb_max handling logic
====================
Link: https://patch.msgid.link/20250529075313.1101820-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The "freq" variable is in terms of MHz and "max_val_cycles" is in terms
of Hz. The fact that "max_val_cycles" is a u64 suggests that support
for high frequency is intended but the "freq_khz * 1000" would overflow
the u32 type if we went above 4GHz. Use unsigned long long type for the
mutliplication to prevent that.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/aDbFHe19juIJKjsb@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bus_id is currently derived from the ethernetX alias. If one is missing
for the device, 0 is used. If ethernet0 points to another stmmac device
or if there are 2+ stmmac devices without an ethernet alias, then bus_id
will be 0 for all of those.
This is an issue because the bus_id is used to generate the mdio bus id
(new_bus->id in drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
stmmac_mdio_register) and this needs to be unique.
This allows to avoid needing to define ethernet aliases for devices with
multiple stmmac controllers (such as the Rockchip RK3588) for multiple
stmmac devices to probe properly.
Obviously, the bus_id isn't guaranteed to be stable across reboots if no
alias is set for the device but that is easily fixed by simply adding an
alias if this is desired.
Fixes: 25c83b5c2e ("dt:net:stmmac: Add support to dwmac version 3.610 and 3.710")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250527-stmmac-mdio-bus_id-v2-1-a5ca78454e3c@cherry.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
echo_skb_max should define the supported upper limit of echo_skb[]
allocated inside the netdevice's priv. The corresponding size value
provided by this driver to alloc_candev() is KVASER_PCIEFD_CAN_TX_MAX_COUNT
which is 17.
But later echo_skb_max is rounded up to the nearest power of two (for the
max case, that would be 32) and the tx/ack indices calculated further
during tx/rx may exceed the upper array boundary. Kasan reported this for
the ack case inside kvaser_pciefd_handle_ack_packet(), though the xmit
function has actually caught the same thing earlier.
BUG: KASAN: slab-out-of-bounds in kvaser_pciefd_handle_ack_packet+0x2d7/0x92a drivers/net/can/kvaser_pciefd.c:1528
Read of size 8 at addr ffff888105e4f078 by task swapper/4/0
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Not tainted 6.15.0 #12 PREEMPT(voluntary)
Call Trace:
<IRQ>
dump_stack_lvl lib/dump_stack.c:122
print_report mm/kasan/report.c:521
kasan_report mm/kasan/report.c:634
kvaser_pciefd_handle_ack_packet drivers/net/can/kvaser_pciefd.c:1528
kvaser_pciefd_read_packet drivers/net/can/kvaser_pciefd.c:1605
kvaser_pciefd_read_buffer drivers/net/can/kvaser_pciefd.c:1656
kvaser_pciefd_receive_irq drivers/net/can/kvaser_pciefd.c:1684
kvaser_pciefd_irq_handler drivers/net/can/kvaser_pciefd.c:1733
__handle_irq_event_percpu kernel/irq/handle.c:158
handle_irq_event kernel/irq/handle.c:210
handle_edge_irq kernel/irq/chip.c:833
__common_interrupt arch/x86/kernel/irq.c:296
common_interrupt arch/x86/kernel/irq.c:286
</IRQ>
Tx max count definitely matters for kvaser_pciefd_tx_avail(), but for seq
numbers' generation that's not the case - we're free to calculate them as
would be more convenient, not taking tx max count into account. The only
downside is that the size of echo_skb[] should correspond to the max seq
number (not tx max count), so in some situations a bit more memory would
be consumed than could be.
Thus make the size of the underlying echo_skb[] sufficient for the rounded
max tx value.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 8256e0ca60 ("can: kvaser_pciefd: Fix echo_skb race")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20250528192713.63894-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
syzbot reported a uaf in page_pool_recycle_in_ring:
BUG: KASAN: slab-use-after-free in lock_release+0x151/0xa30 kernel/locking/lockdep.c:5862
Read of size 8 at addr ffff8880286045a0 by task syz.0.284/6943
CPU: 0 UID: 0 PID: 6943 Comm: syz.0.284 Not tainted 6.13.0-rc3-syzkaller-gdfa94ce54f41 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x169/0x550 mm/kasan/report.c:489
kasan_report+0x143/0x180 mm/kasan/report.c:602
lock_release+0x151/0xa30 kernel/locking/lockdep.c:5862
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:165 [inline]
_raw_spin_unlock_bh+0x1b/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_produce_bh include/linux/ptr_ring.h:164 [inline]
page_pool_recycle_in_ring net/core/page_pool.c:707 [inline]
page_pool_put_unrefed_netmem+0x748/0xb00 net/core/page_pool.c:826
page_pool_put_netmem include/net/page_pool/helpers.h:323 [inline]
page_pool_put_full_netmem include/net/page_pool/helpers.h:353 [inline]
napi_pp_put_page+0x149/0x2b0 net/core/skbuff.c:1036
skb_pp_recycle net/core/skbuff.c:1047 [inline]
skb_free_head net/core/skbuff.c:1094 [inline]
skb_release_data+0x6c4/0x8a0 net/core/skbuff.c:1125
skb_release_all net/core/skbuff.c:1190 [inline]
__kfree_skb net/core/skbuff.c:1204 [inline]
sk_skb_reason_drop+0x1c9/0x380 net/core/skbuff.c:1242
kfree_skb_reason include/linux/skbuff.h:1263 [inline]
__skb_queue_purge_reason include/linux/skbuff.h:3343 [inline]
root cause is:
page_pool_recycle_in_ring
ptr_ring_produce
spin_lock(&r->producer_lock);
WRITE_ONCE(r->queue[r->producer++], ptr)
//recycle last page to pool
page_pool_release
page_pool_scrub
page_pool_empty_ring
ptr_ring_consume
page_pool_return_page //release all page
__page_pool_destroy
free_percpu(pool->recycle_stats);
free(pool) //free
spin_unlock(&r->producer_lock); //pool->ring uaf read
recycle_stat_inc(pool, ring);
page_pool can be free while page pool recycle the last page in ring.
Add producer-lock barrier to page_pool_release to prevent the page
pool from being free before all pages have been recycled.
recycle_stat_inc() is empty when CONFIG_PAGE_POOL_STATS is not
enabled, which will trigger Wempty-body build warning. Add definition
for pool stat macro to fix warning.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/netdev/20250513083123.3514193-1-dongchenchen2@huawei.com
Fixes: ff7d6b27f8 ("page_pool: refurbish version of page_pool code")
Reported-by: syzbot+204a4382fcb3311f3858@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=204a4382fcb3311f3858
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250527114152.3119109-1-dongchenchen2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mii_nway_restart() the code attempts to call
mii->mdio_read which is ch9200_mdio_read(). ch9200_mdio_read()
utilises a local buffer called "buff", which is initialised
with control_read(). However "buff" is conditionally
initialised inside control_read():
if (err == size) {
memcpy(data, buf, size);
}
If the condition of "err == size" is not met, then
"buff" remains uninitialised. Once this happens the
uninitialised "buff" is accessed and returned during
ch9200_mdio_read():
return (buff[0] | buff[1] << 8);
The problem stems from the fact that ch9200_mdio_read()
ignores the return value of control_read(), leading to
uinit-access of "buff".
To fix this we should check the return value of
control_read() and return early on error.
Reported-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=3361c2d6f78a3e0892f9
Tested-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Fixes: 4a476bd6d1 ("usbnet: New driver for QinHeng CH9200 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250526183607.66527-1-qasdev00@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a process under memory pressure is not part of any cgroup and
the charged flag is false, trace_sock_exceed_buf_limit was not called
as expected.
This regression was introduced by commit 2def8ff3fd ("sock:
Code cleanup on __sk_mem_raise_allocated()"). The fix changes the
default value of charged to true while preserving existing logic.
Fixes: 2def8ff3fd ("sock: Code cleanup on __sk_mem_raise_allocated()")
Signed-off-by: Abel Wu <wuyun.abel@bytedance.com>
Signed-off-by: Tengteng Yang <yangtengteng@bytedance.com>
Link: https://patch.msgid.link/20250527030419.67693-1-yangtengteng@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull bpf updates from Alexei Starovoitov:
- Fix and improve BTF deduplication of identical BTF types (Alan
Maguire and Andrii Nakryiko)
- Support up to 12 arguments in BPF trampoline on arm64 (Xu Kuohai and
Alexis Lothoré)
- Support load-acquire and store-release instructions in BPF JIT on
riscv64 (Andrea Parri)
- Fix uninitialized values in BPF_{CORE,PROBE}_READ macros (Anton
Protopopov)
- Streamline allowed helpers across program types (Feng Yang)
- Support atomic update for hashtab of BPF maps (Hou Tao)
- Implement json output for BPF helpers (Ihor Solodrai)
- Several s390 JIT fixes (Ilya Leoshkevich)
- Various sockmap fixes (Jiayuan Chen)
- Support mmap of vmlinux BTF data (Lorenz Bauer)
- Support BPF rbtree traversal and list peeking (Martin KaFai Lau)
- Tests for sockmap/sockhash redirection (Michal Luczaj)
- Introduce kfuncs for memory reads into dynptrs (Mykyta Yatsenko)
- Add support for dma-buf iterators in BPF (T.J. Mercier)
- The verifier support for __bpf_trap() (Yonghong Song)
* tag 'bpf-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (135 commits)
bpf, arm64: Remove unused-but-set function and variable.
selftests/bpf: Add tests with stack ptr register in conditional jmp
bpf: Do not include stack ptr register in precision backtracking bookkeeping
selftests/bpf: enable many-args tests for arm64
bpf, arm64: Support up to 12 function arguments
bpf: Check rcu_read_lock_trace_held() in bpf_map_lookup_percpu_elem()
bpf: Avoid __bpf_prog_ret0_warn when jit fails
bpftool: Add support for custom BTF path in prog load/loadall
selftests/bpf: Add unit tests with __bpf_trap() kfunc
bpf: Warn with __bpf_trap() kfunc maybe due to uninitialized variable
bpf: Remove special_kfunc_set from verifier
selftests/bpf: Add test for open coded dmabuf_iter
selftests/bpf: Add test for dmabuf_iter
bpf: Add open coded dmabuf iterator
bpf: Add dmabuf iterator
dma-buf: Rename debugfs symbols
bpf: Fix error return value in bpf_copy_from_user_dynptr
libbpf: Use mmap to parse vmlinux BTF from sysfs
selftests: bpf: Add a test for mmapable vmlinux BTF
btf: Allow mmap of vmlinux btf
...
Pull networking updates from Paolo Abeni:
"Core:
- Implement the Device Memory TCP transmit path, allowing zero-copy
data transmission on top of TCP from e.g. GPU memory to the wire.
- Move all the IPv6 routing tables management outside the RTNL scope,
under its own lock and RCU. The route control path is now 3x times
faster.
- Convert queue related netlink ops to instance lock, reducing again
the scope of the RTNL lock. This improves the control plane
scalability.
- Refactor the software crc32c implementation, removing unneeded
abstraction layers and improving significantly the related
micro-benchmarks.
- Optimize the GRO engine for UDP-tunneled traffic, for a 10%
performance improvement in related stream tests.
- Cover more per-CPU storage with local nested BH locking; this is a
prep work to remove the current per-CPU lock in local_bh_disable()
on PREMPT_RT.
- Introduce and use nlmsg_payload helper, combining buffer bounds
verification with accessing payload carried by netlink messages.
Netfilter:
- Rewrite the procfs conntrack table implementation, improving
considerably the dump performance. A lot of user-space tools still
use this interface.
- Implement support for wildcard netdevice in netdev basechain and
flowtables.
- Integrate conntrack information into nft trace infrastructure.
- Export set count and backend name to userspace, for better
introspection.
BPF:
- BPF qdisc support: BPF-qdisc can be implemented with BPF struct_ops
programs and can be controlled in similar way to traditional qdiscs
using the "tc qdisc" command.
- Refactor the UDP socket iterator, addressing long standing issues
WRT duplicate hits or missed sockets.
Protocols:
- Improve TCP receive buffer auto-tuning and increase the default
upper bound for the receive buffer; overall this improves the
single flow maximum thoughput on 200Gbs link by over 60%.
- Add AFS GSSAPI security class to AF_RXRPC; it provides transport
security for connections to the AFS fileserver and VL server.
- Improve TCP multipath routing, so that the sources address always
matches the nexthop device.
- Introduce SO_PASSRIGHTS for AF_UNIX, to allow disabling SCM_RIGHTS,
and thus preventing DoS caused by passing around problematic FDs.
- Retire DCCP socket. DCCP only receives updates for bugs, and major
distros disable it by default. Its removal allows for better
organisation of TCP fields to reduce the number of cache lines hit
in the fast path.
- Extend TCP drop-reason support to cover PAWS checks.
Driver API:
- Reorganize PTP ioctl flag support to require an explicit opt-in for
the drivers, avoiding the problem of drivers not rejecting new
unsupported flags.
- Converted several device drivers to timestamping APIs.
- Introduce per-PHY ethtool dump helpers, improving the support for
dump operations targeting PHYs.
Tests and tooling:
- Add support for classic netlink in user space C codegen, so that
ynl-c can now read, create and modify links, routes addresses and
qdisc layer configuration.
- Add ynl sub-types for binary attributes, allowing ynl-c to output
known struct instead of raw binary data, clarifying the classic
netlink output.
- Extend MPTCP selftests to improve the code-coverage.
- Add tests for XDP tail adjustment in AF_XDP.
New hardware / drivers:
- OpenVPN virtual driver: offload OpenVPN data channels processing to
the kernel-space, increasing the data transfer throughput WRT the
user-space implementation.
- Renesas glue driver for the gigabit ethernet RZ/V2H(P) SoC.
- Broadcom asp-v3.0 ethernet driver.
- AMD Renoir ethernet device.
- ReakTek MT9888 2.5G ethernet PHY driver.
- Aeonsemi 10G C45 PHYs driver.
Drivers:
- Ethernet high-speed NICs:
- nVidia/Mellanox (mlx5):
- refactor the steering table handling to significantly
reduce the amount of memory used
- add support for complex matches in H/W flow steering
- improve flow streeing error handling
- convert to netdev instance locking
- Intel (100G, ice, igb, ixgbe, idpf):
- ice: add switchdev support for LLDP traffic over VF
- ixgbe: add firmware manipulation and regions devlink support
- igb: introduce support for frame transmission premption
- igb: adds persistent NAPI configuration
- idpf: introduce RDMA support
- idpf: add initial PTP support
- Meta (fbnic):
- extend hardware stats coverage
- add devlink dev flash support
- Broadcom (bnxt):
- add support for RX-side device memory TCP
- Wangxun (txgbe):
- implement support for udp tunnel offload
- complete PTP and SRIOV support for AML 25G/10G devices
- Ethernet NICs embedded and virtual:
- Google (gve):
- add device memory TCP TX support
- Amazon (ena):
- support persistent per-NAPI config
- Airoha:
- add H/W support for L2 traffic offload
- add per flow stats for flow offloading
- RealTek (rtl8211): add support for WoL magic packet
- Synopsys (stmmac):
- dwmac-socfpga 1000BaseX support
- add Loongson-2K3000 support
- introduce support for hardware-accelerated VLAN stripping
- Broadcom (bcmgenet):
- expose more H/W stats
- Freescale (enetc, dpaa2-eth):
- enetc: add MAC filter, VLAN filter RSS and loopback support
- dpaa2-eth: convert to H/W timestamping APIs
- vxlan: convert FDB table to rhashtable, for better scalabilty
- veth: apply qdisc backpressure on full ring to reduce TX drops
- Ethernet switches:
- Microchip (kzZ88x3): add ETS scheduler support
- Ethernet PHYs:
- RealTek (rtl8211):
- add support for WoL magic packet
- add support for PHY LEDs
- CAN:
- Adds RZ/G3E CANFD support to the rcar_canfd driver.
- Preparatory work for CAN-XL support.
- Add self-tests framework with support for CAN physical interfaces.
- WiFi:
- mac80211:
- scan improvements with multi-link operation (MLO)
- Qualcomm (ath12k):
- enable AHB support for IPQ5332
- add monitor interface support to QCN9274
- add multi-link operation support to WCN7850
- add 802.11d scan offload support to WCN7850
- monitor mode for WCN7850, better 6 GHz regulatory
- Qualcomm (ath11k):
- restore hibernation support
- MediaTek (mt76):
- WiFi-7 improvements
- implement support for mt7990
- Intel (iwlwifi):
- enhanced multi-link single-radio (EMLSR) support on 5 GHz links
- rework device configuration
- RealTek (rtw88):
- improve throughput for RTL8814AU
- RealTek (rtw89):
- add multi-link operation support
- STA/P2P concurrency improvements
- support different SAR configs by antenna
- Bluetooth:
- introduce HCI Driver protocol
- btintel_pcie: do not generate coredump for diagnostic events
- btusb: add HCI Drv commands for configuring altsetting
- btusb: add RTL8851BE device 0x0bda:0xb850
- btusb: add new VID/PID 13d3/3584 for MT7922
- btusb: add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: implement host-wakeup feature"
* tag 'net-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1611 commits)
selftests/bpf: Fix bpf selftest build warning
selftests: netfilter: Fix skip of wildcard interface test
net: phy: mscc: Stop clearing the the UDPv4 checksum for L2 frames
net: openvswitch: Fix the dead loop of MPLS parse
calipso: Don't call calipso functions for AF_INET sk.
selftests/tc-testing: Add a test for HFSC eltree double add with reentrant enqueue behaviour on netem
net_sched: hfsc: Address reentrant enqueue adding class to eltree twice
octeontx2-pf: QOS: Refactor TC_HTB_LEAF_DEL_LAST callback
octeontx2-pf: QOS: Perform cache sync on send queue teardown
net: mana: Add support for Multi Vports on Bare metal
net: devmem: ncdevmem: remove unused variable
net: devmem: ksft: upgrade rx test to send 1K data
net: devmem: ksft: add 5 tuple FS support
net: devmem: ksft: add exit_wait to make rx test pass
net: devmem: ksft: add ipv4 support
net: devmem: preserve sockc_err
page_pool: fix ugly page_pool formatting
net: devmem: move list_add to net_devmem_bind_dmabuf.
selftests: netfilter: nft_queue.sh: include file transfer duration in log message
net: phy: mscc: Fix memory leak when using one step timestamping
...
Pull arm64 updates from Will Deacon:
"The headline feature is the re-enablement of support for Arm's
Scalable Matrix Extension (SME) thanks to a bumper crop of fixes
from Mark Rutland.
If matrices aren't your thing, then Ryan's page-table optimisation
work is much more interesting.
Summary:
ACPI, EFI and PSCI:
- Decouple Arm's "Software Delegated Exception Interface" (SDEI)
support from the ACPI GHES code so that it can be used by platforms
booted with device-tree
- Remove unnecessary per-CPU tracking of the FPSIMD state across EFI
runtime calls
- Fix a node refcount imbalance in the PSCI device-tree code
CPU Features:
- Ensure register sanitisation is applied to fields in ID_AA64MMFR4
- Expose AIDR_EL1 to userspace via sysfs, primarily so that KVM
guests can reliably query the underlying CPU types from the VMM
- Re-enabling of SME support (CONFIG_ARM64_SME) as a result of fixes
to our context-switching, signal handling and ptrace code
Entry code:
- Hook up TIF_NEED_RESCHED_LAZY so that CONFIG_PREEMPT_LAZY can be
selected
Memory management:
- Prevent BSS exports from being used by the early PI code
- Propagate level and stride information to the low-level TLB
invalidation routines when operating on hugetlb entries
- Use the page-table contiguous hint for vmap() mappings with
VM_ALLOW_HUGE_VMAP where possible
- Optimise vmalloc()/vmap() page-table updates to use "lazy MMU mode"
and hook this up on arm64 so that the trailing DSB (used to publish
the updates to the hardware walker) can be deferred until the end
of the mapping operation
- Extend mmap() randomisation for 52-bit virtual addresses (on par
with 48-bit addressing) and remove limited support for
randomisation of the linear map
Perf and PMUs:
- Add support for probing the CMN-S3 driver using ACPI
- Minor driver fixes to the CMN, Arm-NI and amlogic PMU drivers
Selftests:
- Fix FPSIMD and SME tests to align with the freshly re-enabled SME
support
- Fix default setting of the OUTPUT variable so that tests are
installed in the right location
vDSO:
- Replace raw counter access from inline assembly code with a call to
the the __arch_counter_get_cntvct() helper function
Miscellaneous:
- Add some missing header inclusions to the CCA headers
- Rework rendering of /proc/cpuinfo to follow the x86-approach and
avoid repeated buffer expansion (the user-visible format remains
identical)
- Remove redundant selection of CONFIG_CRC32
- Extend early error message when failing to map the device-tree
blob"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (83 commits)
arm64: cputype: Add cputype definition for HIP12
arm64: el2_setup.h: Make __init_el2_fgt labels consistent, again
perf/arm-cmn: Add CMN S3 ACPI binding
arm64/boot: Disallow BSS exports to startup code
arm64/boot: Move global CPU override variables out of BSS
arm64/boot: Move init_pgdir[] and init_idmap_pgdir[] into __pi_ namespace
perf/arm-cmn: Initialise cmn->cpu earlier
kselftest/arm64: Set default OUTPUT path when undefined
arm64: Update comment regarding values in __boot_cpu_mode
arm64: mm: Drop redundant check in pmd_trans_huge()
arm64/mm: Re-organise setting up FEAT_S1PIE registers PIRE0_EL1 and PIR_EL1
arm64/mm: Permit lazy_mmu_mode to be nested
arm64/mm: Disable barrier batching in interrupt contexts
arm64/cpuinfo: only show one cpu's info in c_show()
arm64/mm: Batch barriers when updating kernel mappings
mm/vmalloc: Enter lazy mmu mode while manipulating vmalloc ptes
arm64/mm: Support huge pte-mapped pages in vmap
mm/vmalloc: Gracefully unmap huge ptes
mm/vmalloc: Warn on improper use of vunmap_range()
arm64/mm: Hoist barriers out of set_ptes_anysz() loop
...
Pull nios2 updates fromDinh Nguyen:
- Use strscpy() and simply setup_cpuinfo()
- Remove conflicting mappings when flushing tlb entries
- Force update_mmu_cache on spurious pagefaults
* tag 'nios2_updates_for_v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
nios2: Replace strcpy() with strscpy() and simplify setup_cpuinfo()
nios2: do not introduce conflicting mappings when flushing tlb entries
nios2: force update_mmu_cache on spurious tlb-permission--related pagefaults
Pull crypto fix from Herbert Xu:
"Fix a buffer overflow regression in shash"
* tag 'v6.16-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: shash - Fix buffer overrun in import function
Pull jfs updates from David Kleikamp:
"A few small fixes for jfs"
* tag 'jfs-6.16' of github.com:kleikamp/linux-shaggy:
jfs: fix array-index-out-of-bounds read in add_missing_indices
jfs: Fix null-ptr-deref in jfs_ioc_trim
jfs: validate AG parameters in dbMount() to prevent crashes
Pull dlm updates from David Teigland:
"This fixes delays when shutting down SCTP connections, and updates dlm
Kconfig for SCTP"
* tag 'dlm-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: drop SCTP Kconfig dependency
dlm: reject SCTP configuration if not enabled
dlm: use SHUT_RDWR for SCTP shutdown
dlm: mask sk_shutdown value
Pull nfsd updates from Chuck Lever:
"The marquee feature for this release is that the limit on the maximum
rsize and wsize has been raised to 4MB. The default remains at 1MB,
but risk-seeking administrators now have the ability to try larger I/O
sizes with NFS clients that support them. Eventually the default
setting will be increased when we have confidence that this change
will not have negative impact.
With v6.16, NFSD now has its own debugfs file system where we can add
experimental features and make them available outside of our
development community without impacting production deployments. The
first experimental setting added is one that makes all NFS READ
operations use vfs_iter_read() instead of the NFSD splice actor. The
plan is to eventually retire the splice actor, as that will enable a
number of new capabilities such as the use of struct bio_vec from the
top to the bottom of the NFSD stack.
Jeff Layton contributed a number of observability improvements. The
use of dprintk() in a number of high-traffic code paths has been
replaced with static trace points.
This release sees the continuation of efforts to harden the NFSv4.2
COPY operation. Soon, the restriction on async COPY operations can be
lifted.
Many thanks to the contributors, reviewers, testers, and bug reporters
who participated during the v6.16 development cycle"
* tag 'nfsd-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux: (60 commits)
xdrgen: Fix code generated for counted arrays
SUNRPC: Bump the maximum payload size for the server
NFSD: Add a "default" block size
NFSD: Remove NFSSVC_MAXBLKSIZE_V2 macro
NFSD: Remove NFSD_BUFSIZE
sunrpc: Remove the RPCSVC_MAXPAGES macro
svcrdma: Adjust the number of entries in svc_rdma_send_ctxt::sc_pages
svcrdma: Adjust the number of entries in svc_rdma_recv_ctxt::rc_pages
sunrpc: Adjust size of socket's receive page array dynamically
SUNRPC: Remove svc_rqst :: rq_vec
SUNRPC: Remove svc_fill_write_vector()
NFSD: Use rqstp->rq_bvec in nfsd_iter_write()
SUNRPC: Export xdr_buf_to_bvec()
NFSD: De-duplicate the svc_fill_write_vector() call sites
NFSD: Use rqstp->rq_bvec in nfsd_iter_read()
sunrpc: Replace the rq_bvec array with dynamically-allocated memory
sunrpc: Replace the rq_pages array with dynamically-allocated memory
sunrpc: Remove backchannel check in svc_init_buffer()
sunrpc: Add a helper to derive maxpages from sv_max_mesg
svcrdma: Reduce the number of rdma_rw contexts per-QP
...
Pull ext4 updates from Ted Ts'o:
"New ext4 features and performance improvements:
- Fast commit performance improvements
- Multi-fsblock atomic write support for bigalloc file systems
- Large folio support for regular files
This last can result in really stupendous performance for the right
workloads. For example, see [1] where the Kernel Test Robot reported
over 37% improvement on a large sequential I/O workload.
There are also the usual bug fixes and cleanups. Of note are cleanups
of the extent status tree to fix potential races that could result in
the extent status tree getting corrupted under heavy simultaneous
allocation and deallocation to a single file"
Link: https://lore.kernel.org/all/202505161418.ec0d753f-lkp@intel.com/ [1]
* tag 'ext4_for_linus-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (52 commits)
ext4: Add a WARN_ON_ONCE for querying LAST_IN_LEAF instead
ext4: Simplify flags in ext4_map_query_blocks()
ext4: Rename and document EXT4_EX_FILTER to EXT4_EX_QUERY_FILTER
ext4: Simplify last in leaf check in ext4_map_query_blocks
ext4: Unwritten to written conversion requires EXT4_EX_NOCACHE
ext4: only dirty folios when data journaling regular files
ext4: Add atomic block write documentation
ext4: Enable support for ext4 multi-fsblock atomic write using bigalloc
ext4: Add multi-fsblock atomic write support with bigalloc
ext4: Add support for EXT4_GET_BLOCKS_QUERY_LEAF_BLOCKS
ext4: Make ext4_meta_trans_blocks() non-static for later use
ext4: Check if inode uses extents in ext4_inode_can_atomic_write()
ext4: Document an edge case for overwrites
jbd2: remove journal_t argument from jbd2_superblock_csum()
jbd2: remove journal_t argument from jbd2_chksum()
ext4: remove sb argument from ext4_superblock_csum()
ext4: remove sbi argument from ext4_chksum()
ext4: enable large folio for regular file
ext4: make online defragmentation support large folios
ext4: make the writeback path support large folios
...
Pull ntfs updates from Konstantin Komarov:
"Added:
- missing direct_IO in ntfs_aops_cmpr
- handling of hdr_first_de() return value
Fixed:
- handling of InitializeFileRecordSegment operation.
Removed:
- ability to change compression on mounted volume
- redundant NULL check"
* tag 'ntfs3_for_6.16' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: remove ability to change compression on mounted volume
fs/ntfs3: Fix handling of InitializeFileRecordSegment
fs/ntfs3: Add missing direct_IO in ntfs_aops_cmpr
fs/ntfs3: handle hdr_first_de() return value
fs/ntfs3: Drop redundant NULL check
Pull orangefs update from Mike Marshall:
"Convert to use the new mount API.
Code from Eric Sandeen at redhat that converts orangefs over to the
new mount API"
* tag 'for-linus-6.16-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: Convert to use the new mount API
Pull exfat updates from Namjae Jeon:
- Fix xfstests generic/482 test failure
- Fix double free in delayed_free
* tag 'exfat-for-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: do not clear volume dirty flag during sync
exfat: fix double free in delayed_free
Pull btrfs fix from David Sterba:
"A fixup to the xarray conversion sent in the main 6.16 batch. It was
not included because it would cause rebase/refresh of like 80 patches,
right before sending the early pull request last week.
It's fixing a bug when zoned mode is enabled on btrfs so it's not
affecting most people"
* tag 'for-6.16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: don't drop a reference if btrfs_check_write_meta_pointer() fails
Pull drm updates from Dave Airlie:
"As part of building up nova-core/nova-drm pieces we've brought in some
rust abstractions through this tree, aux bus being the main one, with
devres changes also in the driver-core tree. Along with the drm core
abstractions and enough nova-core/nova-drm to use them. This is still
all stub work under construction, to build the nova driver upstream.
The other big NVIDIA related one is nouveau adds support for
Hopper/Blackwell GPUs, this required a new GSP firmware update to
570.144, and a bunch of rework in order to support multiple fw
interfaces.
There is also the introduction of an asahi uapi header file as a
precursor to getting the real driver in later, but to unblock
userspace mesa packages while the driver is trapped behind rust
enablement.
Otherwise it's the usual mixture of stuff all over, amdgpu, i915/xe,
and msm being the main ones, and some changes to vsprintf.
new drivers:
- bring in the asahi uapi header standalone
- nova-drm: stub driver
rust dependencies (for nova-core):
- auxiliary
- bus abstractions
- driver registration
- sample driver
- devres changes from driver-core
- revocable changes
core:
- add Apple fourcc modifiers
- add virtio capset definitions
- extend EXPORT_SYNC_FILE for timeline syncobjs
- convert to devm_platform_ioremap_resource
- refactor shmem helper page pinning
- DP powerup/down link helpers
- extended %p4cc in vsprintf.c to support fourcc prints
- change vsprintf %p4cn to %p4chR, remove %p4cn
- Add drm_file_err function
- IN_FORMATS_ASYNC property
- move sitronix from tiny to their own subdir
rust:
- add drm core infrastructure rust abstractions
(device/driver, ioctl, file, gem)
dma-buf:
- adjust sg handling to not cache map on attach
- allow setting dma-device for import
- Add a helper to sort and deduplicate dma_fence arrays
docs:
- updated drm scheduler docs
- fbdev todo update
- fb rendering
- actual brightness
ttm:
- fix delayed destroy resv object
bridge:
- add kunit tests
- convert tc358775 to atomic
- convert drivers to devm_drm_bridge_alloc
- convert rk3066_hdmi to bridge driver
scheduler:
- add kunit tests
panel:
- refcount panels to improve lifetime handling
- Powertip PH128800T004-ZZA01
- NLT NL13676BC25-03F, Tianma TM070JDHG34-00
- Himax HX8279/HX8279-D DDIC
- Visionox G2647FB105
- Sitronix ST7571
- ZOTAC rotation quirk
vkms:
- allow attaching more displays
i915:
- xe3lpd display updates
- vrr refactor
- intel_display struct conversions
- xe2hpd memory type identification
- add link rate/count to i915_display_info
- cleanup VGA plane handling
- refactor HDCP GSC
- fix SLPC wait boosting reference counting
- add 20ms delay to engine reset
- fix fence release on early probe errors
xe:
- SRIOV updates
- BMG PCI ID update
- support separate firmware for each GT
- SVM fix, prelim SVM multi-device work
- export fan speed
- temp disable d3cold on BMG
- backup VRAM in PM notifier instead of suspend/freeze
- update xe_ttm_access_memory to use GPU for non-visible access
- fix guc_info debugfs for VFs
- use copy_from_user instead of __copy_from_user
- append PCIe gen5 limitations to xe_firmware document
amdgpu:
- DSC cleanup
- DC Scaling updates
- Fused I2C-over-AUX updates
- DMUB updates
- Use drm_file_err in amdgpu
- Enforce isolation updates
- Use new dma_fence helpers
- USERQ fixes
- Documentation updates
- SR-IOV updates
- RAS updates
- PSP 12 cleanups
- GC 9.5 updates
- SMU 13.x updates
- VCN / JPEG SR-IOV updates
amdkfd:
- Update error messages for SDMA
- Userptr updates
- XNACK fixes
radeon:
- CIK doorbell cleanup
nouveau:
- add support for NVIDIA r570 GSP firmware
- enable Hopper/Blackwell support
nova-core:
- fix task list
- register definition infrastructure
- move firmware into own rust module
- register auxiliary device for nova-drm
nova-drm:
- initial driver skeleton
msm:
- GPU:
- ACD (adaptive clock distribution) for X1-85
- drop fictional address_space_size
- improve GMU HFI response time out robustness
- fix crash when throttling during boot
- DPU:
- use single CTL path for flushing on DPU 5.x+
- improve SSPP allocation code for better sharing
- Enabled SmartDMA on SM8150, SC8180X, SC8280XP, SM8550
- Added SAR2130P support
- Disabled DSC support on MSM8937, MSM8917, MSM8953, SDM660
- DP:
- switch to new audio helpers
- better LTTPR handling
- DSI:
- Added support for SA8775P
- Added SAR2130P support
- HDMI:
- Switched to use new helpers for ACR data
- Fixed old standing issue of HPD not working in some cases
amdxdna:
- add dma-buf support
- allow empty command submits
renesas:
- add dma-buf support
- add zpos, alpha, blend support
panthor:
- fail properly for NO_MMAP bos
- add SET_LABEL ioctl
- debugfs BO dumping support
imagination:
- update DT bindings
- support TI AM68 GPU
hibmc:
- improve interrupt handling and HPD support
virtio:
- add panic handler support
rockchip:
- add RK3588 support
- add DP AUX bus panel support
ivpu:
- add heartbeat based hangcheck
mediatek:
- prepares support for MT8195/99 HDMIv2/DDCv2
anx7625:
- improve HPD
tegra:
- speed up firmware loading
* tag 'drm-next-2025-05-28' of https://gitlab.freedesktop.org/drm/kernel: (1627 commits)
drm/nouveau/tegra: Fix error pointer vs NULL return in nvkm_device_tegra_resource_addr()
drm/xe: Default auto_link_downgrade status to false
drm/xe/guc: Make creation of SLPC debugfs files conditional
drm/i915/display: Add check for alloc_ordered_workqueue() and alloc_workqueue()
drm/i915/dp_mst: Work around Thunderbolt sink disconnect after SINK_COUNT_ESI read
drm/i915/ptl: Use everywhere the correct DDI port clock select mask
drm/nouveau/kms: add support for GB20x
drm/dp: add option to disable zero sized address only transactions.
drm/nouveau: add support for GB20x
drm/nouveau/gsp: add hal for fifo.chan.doorbell_handle
drm/nouveau: add support for GB10x
drm/nouveau/gf100-: track chan progress with non-WFI semaphore release
drm/nouveau/nv50-: separate CHANNEL_GPFIFO handling out from CHANNEL_DMA
drm/nouveau: add helper functions for allocating pinned/cpu-mapped bos
drm/nouveau: add support for GH100
drm/nouveau: improve handling of 64-bit BARs
drm/nouveau/gv100-: switch to volta semaphore methods
drm/nouveau/gsp: support deeper page tables in COPY_SERVER_RESERVED_PDES
drm/nouveau/gsp: init client VMMs with NV0080_CTRL_DMA_SET_PAGE_DIRECTORY
drm/nouveau/gsp: fetch level shift and PDE from BAR2 VMM
...
Pull media updates from Mauro Carvalho Chehab:
- v4l2-core fix: V4L2_BUF_TYPE_VIDEO_OVERLAY is capture, not output
- New driver: Amlogic C3 ISP
- New sensor drivers: ST VD55G1 and VD56G3, OmniVision OV02C10
- amlogic: c3-mipi-csi2: Handle 64-bits division
- a fix for 64-bits division at the amlogic c3-mipi-csi2 driver
- Changes at atomisp to support mainline mt9m114 driver and remove
deprecated GPIO APIs
- various cleanups, fixes and enhancements
* tag 'media/v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (314 commits)
media: rkvdec: h264: Support High 10 and 4:2:2 profiles
media: rkvdec: Add get_image_fmt ops
media: rkvdec: Initialize the m2m context before the controls
media: rkvdec: h264: Limit minimum profile to constrained baseline
media: mediatek: jpeg: support 34bits
media: verisilicon: Free post processor buffers on error
media: platform: mtk-mdp3: Remove unused mdp_get_plat_device
media: amlogic: c3-mipi-csi2: Handle 64-bits division
media: uvcvideo: Use dev_err_probe for devm_gpiod_get_optional
media: uvcvideo: Fix deferred probing error
media: uvcvideo: Rollback non processed entities on error
media: uvcvideo: Send control events for partial succeeds
media: uvcvideo: Return the number of processed controls
media: uvcvideo: Do not turn on the camera for some ioctls
media: uvcvideo: Make power management granular
media: uvcvideo: Increase/decrease the PM counter per IOCTL
media: uvcvideo: Create uvc_pm_(get|put) functions
media: uvcvideo: Keep streaming state in the file handle
Documentation: media: Add documentation file c3-isp.rst
Documentation: media: Add documentation file metafmt-c3-isp.rst
...
Pull audit updates from Paul Moore:
- Always record AUDIT_ANOM events when auditing is enabled.
Prior to this patch we only recorded AUDIT_ANOM events if auditing
was enabled and the admin/distro had explicitly configured audit
beyond the defaults. Considering that AUDIT_ANOM events are anomolous
events considered to be "security relevant", it seems wise to record
these events as long as auditing is enabled, even if the system is
running with a default audit configuration.
- Mark the audit_log_vformat() function with the __printf() attribute
to quiet GCC.
* tag 'audit-pr-20250527' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: record AUDIT_ANOM_* events regardless of presence of rules
audit: mark audit_log_vformat() with __printf() attribute
Pull selinux updates from Paul Moore:
- Reduce the SELinux impact on path walks.
Add a small directory access cache to the per-task SELinux state.
This cache allows SELinux to cache the most recently used directory
access decisions in order to avoid repeatedly querying the AVC on
path walks where the majority of the directories have similar
security contexts/labels.
My performance measurements are crude, but prior to this patch the
time spent in SELinux code on a 'make allmodconfig' run was 103% that
of __d_lookup_rcu(), and with this patch the time spent in SELinux
code dropped to 63% of __d_lookup_rcu(), a ~40% improvement.
Additional improvments can be expected in the future, but those will
require additional SELinux policy/toolchain support.
- Add support for wildcards in genfscon policy statements.
This patch allows for wildcards in the genfscon patch matching logic
as opposed to the prefix matching that was used prior to this change.
Adding wilcard support allows for more expressive and efficient path
matching in the policy which is especially helpful for sysfs, and has
resulted in a ~15% boot time reduction in Android.
SELinux policies can opt into wilcard matching by using the
"genfs_seclabel_wildcard" policy capability.
- Unify the error/OOM handling of the SELinux network caches.
A failure to allocate memory for the SELinux network caches isn't
fatal as the object label can still be safely returned to the caller,
it simply means that we cannot add the new data to the cache, at
least temporarily. This patch corrects this behavior for the
InfiniBand cache and does some minor cleanup.
- Minor improvements around constification, 'likely' annotations, and
removal of bogus comments.
* tag 'selinux-pr-20250527' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix the kdoc header for task_avdcache_update
selinux: remove a duplicated include
selinux: reduce path walk overhead
selinux: support wildcard match in genfscon
selinux: drop copy-paste comment
selinux: unify OOM handling in network hashtables
selinux: add likely hints for fast paths
selinux: contify network namespace pointer
selinux: constify network address pointer
Pull lsm update from Paul Moore:
"One minor LSM framework patch to move the selinux_netlink_send() hook
under the CONFIG_SECURITY_NETWORK Kconfig knob"
* tag 'lsm-pr-20250527' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
lsm: Move security_netlink_send to under CONFIG_SECURITY_NETWORK
Pull integrity updates from Mimi Zohar:
"Carrying the IMA measurement list across kexec is not a new feature,
but is updated to address a couple of issues:
- Carrying the IMA measurement list across kexec required knowing
apriori all the file measurements between the "kexec load" and
"kexec execute" in order to measure them before the "kexec load".
Any delay between the "kexec load" and "kexec exec" exacerbated the
problem.
- Any file measurements post "kexec load" were not carried across
kexec, resulting in the measurement list being out of sync with the
TPM PCR.
With these changes, the buffer for the IMA measurement list is still
allocated at "kexec load", but copying the IMA measurement list is
deferred to after quiescing the TPM.
Two new kexec critical data records are defined"
* tag 'integrity-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: do not copy measurement list to kdump kernel
ima: measure kexec load and exec events as critical data
ima: make the kexec extra memory configurable
ima: verify if the segment size has changed
ima: kexec: move IMA log copy from kexec load to execute
ima: kexec: define functions to copy IMA log at soft boot
ima: kexec: skip IMA segment validation after kexec soft reboot
kexec: define functions to map and unmap segments
ima: define and call ima_alloc_kexec_file_buf()
ima: rename variable the seq_file "file" to "ima_kexec_file"
Pull smack update from Casey Schaufler:
"One trivial kernel doc fix"
* tag 'Smack-for-6.16' of https://github.com/cschaufler/smack-next:
security/smack/smackfs: small kernel-doc fixes
Pull hardening updates from Kees Cook:
- Update overflow helpers to ease refactoring of on-stack flex array
instances (Gustavo A. R. Silva, Kees Cook)
- lkdtm: Use SLAB_NO_MERGE instead of constructors (Harry Yoo)
- Simplify CONFIG_CC_HAS_COUNTED_BY (Jan Hendrik Farr)
- Disable u64 usercopy KUnit test on 32-bit SPARC (Thomas Weißschuh)
- Add missed designated initializers now exposed by fixed randstruct
(Nathan Chancellor, Kees Cook)
- Document compilers versions for __builtin_dynamic_object_size
- Remove ARM_SSP_PER_TASK GCC plugin
- Fix GCC plugin randstruct, add selftests, and restore COMPILE_TEST
builds
- Kbuild: induce full rebuilds when dependencies change with GCC
plugins, the Clang sanitizer .scl file, or the randstruct seed.
- Kbuild: Switch from -Wvla to -Wvla-larger-than=1
- Correct several __nonstring uses for -Wunterminated-string-initialization
* tag 'hardening-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
Revert "hardening: Disable GCC randstruct for COMPILE_TEST"
lib/tests: randstruct: Add deep function pointer layout test
lib/tests: Add randstruct KUnit test
randstruct: gcc-plugin: Remove bogus void member
net: qede: Initialize qede_ll_ops with designated initializer
scsi: qedf: Use designated initializer for struct qed_fcoe_cb_ops
md/bcache: Mark __nonstring look-up table
integer-wrap: Force full rebuild when .scl file changes
randstruct: Force full rebuild when seed changes
gcc-plugins: Force full rebuild when plugins change
kbuild: Switch from -Wvla to -Wvla-larger-than=1
hardening: simplify CONFIG_CC_HAS_COUNTED_BY
overflow: Fix direct struct member initialization in _DEFINE_FLEX()
kunit/overflow: Add tests for STACK_FLEX_ARRAY_SIZE() helper
overflow: Add STACK_FLEX_ARRAY_SIZE() helper
input/joystick: magellan: Mark __nonstring look-up table const
watchdog: exar: Shorten identity name to fit correctly
mod_devicetable: Enlarge the maximum platform_device_id name length
overflow: Clarify expectations for getting DEFINE_FLEX variable sizes
compiler_types: Identify compiler versions for __builtin_dynamic_object_size
...
Pull seccomp updates from Kees Cook:
- selftest fixes for arm32 (Neill Kapron, Terry Tritton)
- documentation typo fix (Sumanth Gavini)
* tag 'seccomp-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
selftests: seccomp: Fix "performace" to "performance"
selftests/seccomp: fix negative_ENOSYS tracer tests on arm32
selftests/seccomp: fix syscall_restart test for arm compat
The script is supposed to skip wildcard interface testing if unsupported
by the host's nft tool. The failing check caused script abort due to
'set -e' though. Fix this by running the potentially failing nft command
inside the if-conditional pipe.
Fixes: 73db1b5dab ("selftests: netfilter: Torture nftables netdev hooks")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://patch.msgid.link/20250527094117.18589-1-phil@nwl.cc
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We have noticed that when PHY timestamping is enabled, L2 frames seems
to be modified by changing two 2 bytes with a value of 0. The place were
these 2 bytes seems to be random(or I couldn't find a pattern). In most
of the cases the userspace can ignore these frames but if for example
those 2 bytes are in the correction field there is nothing to do. This
seems to happen when configuring the HW for IPv4 even that the flow is
not enabled.
These 2 bytes correspond to the UDPv4 checksum and once we don't enable
clearing the checksum when using L2 frames then the frame doesn't seem
to be changed anymore.
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250523082716.2935895-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The unexpected MPLS packet may not end with the bottom label stack.
When there are many stacks, The label count value has wrapped around.
A dead loop occurs, soft lockup/CPU stuck finally.
stack backtrace:
UBSAN: array-index-out-of-bounds in /build/linux-0Pa0xK/linux-5.15.0/net/openvswitch/flow.c:662:26
index -1 is out of range for type '__be32 [3]'
CPU: 34 PID: 0 Comm: swapper/34 Kdump: loaded Tainted: G OE 5.15.0-121-generic #131-Ubuntu
Hardware name: Dell Inc. PowerEdge C6420/0JP9TF, BIOS 2.12.2 07/14/2021
Call Trace:
<IRQ>
show_stack+0x52/0x5c
dump_stack_lvl+0x4a/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x36
__ubsan_handle_out_of_bounds.cold+0x44/0x49
key_extract_l3l4+0x82a/0x840 [openvswitch]
? kfree_skbmem+0x52/0xa0
key_extract+0x9c/0x2b0 [openvswitch]
ovs_flow_key_extract+0x124/0x350 [openvswitch]
ovs_vport_receive+0x61/0xd0 [openvswitch]
? kernel_init_free_pages.part.0+0x4a/0x70
? get_page_from_freelist+0x353/0x540
netdev_port_receive+0xc4/0x180 [openvswitch]
? netdev_port_receive+0x180/0x180 [openvswitch]
netdev_frame_hook+0x1f/0x40 [openvswitch]
__netif_receive_skb_core.constprop.0+0x23a/0xf00
__netif_receive_skb_list_core+0xfa/0x240
netif_receive_skb_list_internal+0x18e/0x2a0
napi_complete_done+0x7a/0x1c0
bnxt_poll+0x155/0x1c0 [bnxt_en]
__napi_poll+0x30/0x180
net_rx_action+0x126/0x280
? bnxt_msix+0x67/0x80 [bnxt_en]
handle_softirqs+0xda/0x2d0
irq_exit_rcu+0x96/0xc0
common_interrupt+0x8e/0xa0
</IRQ>
Fixes: fbdcdd78da ("Change in Openvswitch to support MPLS label depth of 3 in ingress direction")
Signed-off-by: Faicker Mo <faicker.mo@zenlayer.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/259D3404-575D-4A6D-B263-1DF59A67CF89@zenlayer.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
