Fix unintended sign extension and klockwork issues. These are not real
issue but for sanity checks.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC queues needs to be correctly updated when the number of queues on
a VSI is reconfigured, so netdev's queue and TC settings will be
dynamically adjusted and could accurately represent the underlying
hardware state after changes to the VSI queue counts.
Fixes: 0754d65bd4 ("ice: Add infrastructure for mqprio support via ndo_setup_tc")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE1588(ptp) is optional feature for network. Remove it from required
list to fix below CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: ethernet@f0000: 'ptp-timer' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all PSE attributes are used for the pse-set netlink command.
Select only the ones used by ethtool.
Fixes: f8586411e4 ("netlink: specs: Expand the pse netlink command with PoE interface")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 types of outstanding tx skb's:
Type 1: Packets that are sitting in the drivers ind_buff that are
waiting to be batch sent to the NIC. During a device reset, these are
freed with a call to ibmvnic_tx_scrq_clean_buffer()
Type 2: Packets that have been sent to the NIC and are awaiting a TX
completion IRQ. These are free'd during a reset with a call to
clean_tx_pools()
During any reset which requires us to free the tx irq, ensure that the
Type 2 skb references are freed. Since the irq is released, it is
impossible for the NIC to inform of any completions.
Furthermore, later in the reset process is a call to init_tx_pools()
which marks every entry in the tx pool as free (ie not outstanding).
So if the driver is to make a call to init_tx_pools(), it must first
be sure that the tx pool is empty of skb references.
This issue was discovered by observing the following in the logs during
EEH testing:
TX free map points to untracked skb (tso_pool 0 idx=4)
TX free map points to untracked skb (tso_pool 0 idx=5)
TX free map points to untracked skb (tso_pool 1 idx=36)
Fixes: 65d6470d13 ("ibmvnic: clean pending indirect buffs during reset")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Don't accept TT entries for out-of-spec VIDs, by Sven Eckelmann
- Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only
callbacks", by Linus Lüssing
* tag 'batadv-net-pullrequest-20240621' of git://git.open-mesh.org/linux-merge:
Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only callbacks"
batman-adv: Don't accept TT entries for out-of-spec VIDs
====================
Link: https://patch.msgid.link/20240621143915.49137-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2024-06-21
The first patch is by Oleksij Rempel, it enhances the error handling
for tightly received RTS message in the j1939 protocol.
Shigeru Yoshida's patch fixes a kernel information leak in
j1939_send_one() in the j1939 protocol.
Followed by a patch by Oleksij Rempel for the j1939 protocol, to
properly recover from a CAN bus error during BAM transmission.
A patch by Chen Ni properly propagates errors in the kvaser_usb
driver.
The last patch is by Vitor Soares, that fixes an infinite loop in the
mcp251xfd driver is SPI async sending fails during xmit.
* tag 'linux-can-fixes-for-6.10-20240621' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: fix infinite loop when xmit fails
can: kvaser_usb: fix return value for hif_usb_send_regout
net: can: j1939: recover socket queue on CAN bus error during BAM transmission
net: can: j1939: Initialize unused data in j1939_send_one()
net: can: j1939: enhanced error handling for tightly received RTS messages in xtp_rx_rts_session_new
====================
Link: https://patch.msgid.link/20240621121739.434355-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure the inner IP header is part of the skb's linear data before
setting old_iph. Otherwise, on a non-linear skb, old_iph could point
outside of the packet data.
Unlike classical VXLAN, which always encapsulates Ethernet packets,
VXLAN-GPE can transport IP packets directly. In that case, we need to
look at skb->protocol to figure out if an Ethernet header is present.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/2aa75f6fa62ac9dbe4f16ad5ba75dd04a51d4b99.1718804000.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
mlxsw: Fixes
This patchset fixes an issue with mlxsw driver initialization, and a
memory corruption issue in shared buffer occupancy handling.
v3:
- Drop the core thermal fix, it's not relevant anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following two shared buffer operations make use of the Shared Buffer
Status Register (SBSR):
# devlink sb occupancy snapshot pci/0000:01:00.0
# devlink sb occupancy clearmax pci/0000:01:00.0
The register has two masks of 256 bits to denote on which ingress /
egress ports the register should operate on. Spectrum-4 has more than
256 ports, so the register was extended by cited commit with a new
'port_page' field.
However, when filling the register's payload, the driver specifies the
ports as absolute numbers and not relative to the first port of the port
page, resulting in memory corruptions [1].
Fix by specifying the ports relative to the first port of the port page.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
Read of size 1 at addr ffff8881068cb00f by task devlink/1566
[...]
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
mlxsw_devlink_sb_occ_snapshot+0x75/0xb0
devlink_nl_sb_occ_snapshot_doit+0x1f9/0x2a0
genl_family_rcv_msg_doit+0x20c/0x300
genl_rcv_msg+0x567/0x800
netlink_rcv_skb+0x170/0x450
genl_rcv+0x2d/0x40
netlink_unicast+0x547/0x830
netlink_sendmsg+0x8d4/0xdb0
__sys_sendto+0x49b/0x510
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
copy_verifier_state+0xbc2/0xfb0
do_check_common+0x2c51/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x109/0x170
__kasan_slab_free+0x14/0x30
kfree+0xca/0x2b0
free_verifier_state+0xce/0x270
do_check_common+0x4828/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: f8538aec88 ("mlxsw: Add support for more than 256 ports in SBSR register")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit added support for a new reset flow ("all reset") which is
deeper than the existing reset flow ("software reset") and allows the
device's PCI firmware to be upgraded.
In the new flow the driver first tells the firmware that "all reset" is
required by issuing a new reset command (i.e., MRSR.command=6) and then
triggers the reset by having the PCI core issue a secondary bus reset
(SBR).
However, due to a race condition in the device's firmware the device is
not always able to recover from this reset, resulting in initialization
failures [1].
New firmware versions include a fix for the bug and advertise it using a
new capability bit in the Management Capabilities Mask (MCAM) register.
Avoid initialization failures by reading the new capability bit and
triggering the new reset flow only if the bit is set. If the bit is not
set, trigger a normal PCI hot reset by skipping the call to the
Management Reset and Shutdown Register (MRSR).
Normal PCI hot reset is weaker than "all reset", but it results in a
fully operational driver and allows users to flash a new firmware, if
they want to.
[1]
mlxsw_spectrum4 0000:01:00.0: not ready 1023ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 2047ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 4095ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 8191ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 16383ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 32767ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 65535ms after bus reset; giving up
mlxsw_spectrum4 0000:01:00.0: PCI function reset failed with -25
mlxsw_spectrum4 0000:01:00.0: cannot register bus device
mlxsw_spectrum4: probe of 0000:01:00.0 failed with error -25
Fixes: f257c73e53 ("mlxsw: pci: Add support for new reset flow")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our corporate overlords have been changing the domains around
again and this mailing list has gone away.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __ethtool_get_ts_info function returns directly if the device has a
get_ts_info() method. For bonding with an active slave, this works correctly
as we simply return the real device's timestamping information. However,
when there is no active slave, we only check the slave's TX software
timestamp information. We still need to set the phc index and RX timestamp
information manually. Otherwise, the result will be look like:
Time stamping parameters for bond0:
Capabilities:
software-transmit
PTP Hardware Clock: 0
Hardware Transmit Timestamp Modes: none
Hardware Receive Filter Modes: none
This issue does not affect VLAN or MACVLAN devices, as they only have one
downlink and can directly use the downlink's timestamping information.
Fixes: b8768dc407 ("net: ethtool: Refactor identical get_ts_info implementations.")
Reported-by: Liang Li <liali@redhat.com>
Closes: https://issues.redhat.com/browse/RHEL-42409
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya found a failure in running check-kernel tests with at_groups=144
(144: conntrack - FTP SNAT orig tuple) in OVS repo. After his further
investigation, the root cause is that the labels sent to userspace
for related ct are incorrect.
The labels for unconfirmed related ct should use its master's labels.
However, the changes made in commit 8c8b733208 ("openvswitch: set
IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
led to getting labels from this related ct.
So fix it in ovs_ct_get_labels() by changing to copy labels from its
master ct if it is a unconfirmed related ct. Note that there is no
fix needed for ct->mark, as it was already copied from its master
ct for related ct in init_conntrack().
Fixes: 8c8b733208 ("openvswitch: set IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Tested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Link: https://lore.kernel.org/all/20240517134355.770777-1-ivitro@gmail.com
[mkl: use more imperative wording in patch description]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch enhances error handling in scenarios with RTS (Request to
Send) messages arriving closely. It replaces the less informative WARN_ON_ONCE
backtraces with a new error handling method. This provides clearer error
messages and allows for the early termination of problematic sessions.
Previously, sessions were only released at the end of j1939_xtp_rx_rts().
Potentially this could be reproduced with something like:
testj1939 -r vcan0:0x80 &
while true; do
# send first RTS
cansend vcan0 18EC8090#1014000303002301;
# send second RTS
cansend vcan0 18EC8090#1014000303002301;
# send abort
cansend vcan0 18EC8090#ff00000000002301;
done
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Reported-by: syzbot+daa36413a5cedf799ae4@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20231117124959.961171-1-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, bpf and netfilter.
Happy summer solstice! The line count is a bit inflated by a selftest
and update to a driver's FW interface header, in reality this is
slightly below average for us. We are expecting one driver fix from
Intel, but there are no big known issues.
Current release - regressions:
- ipv6: bring NLM_DONE out to a separate recv() again
Current release - new code bugs:
- wifi: cfg80211: wext: set ssids=NULL for passive scans via old wext API
Previous releases - regressions:
- wifi: mac80211: fix monitor channel setting with chanctx emulation
(probably most awaited of the fixes in this PR, tracked by Thorsten)
- usb: ax88179_178a: bring back reset on init, if PHY is disconnected
- bpf: fix UML x86_64 compile failure with BPF
- bpf: avoid splat in pskb_pull_reason(), sanity check added can be hit
with malicious BPF
- eth: mvpp2: use slab_build_skb() for packets in slab, driver was
missed during API refactoring
- wifi: iwlwifi: add missing unlock of mvm mutex
Previous releases - always broken:
- ipv6: add a number of missing null-checks for in6_dev_get(), in case
IPv6 disabling races with the datapath
- bpf: fix reg_set_min_max corruption of fake_reg
- sched: act_ct: add netns as part of the key of tcf_ct_flow_table"
* tag 'net-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (63 commits)
net: usb: rtl8150 fix unintiatilzed variables in rtl8150_get_link_ksettings
selftests: virtio_net: add forgotten config options
bnxt_en: Restore PTP tx_avail count in case of skb_pad() error
bnxt_en: Set TSO max segs on devices with limits
bnxt_en: Update firmware interface to 1.10.3.44
net: stmmac: Assign configured channel value to EXTTS event
net: do not leave a dangling sk pointer, when socket creation fails
net/tcp_ao: Don't leak ao_info on error-path
ice: Fix VSI list rule with ICE_SW_LKUP_LAST type
ipv6: bring NLM_DONE out to a separate recv() again
selftests: add selftest for the SRv6 End.DX6 behavior with netfilter
selftests: add selftest for the SRv6 End.DX4 behavior with netfilter
netfilter: move the sysctl nf_hooks_lwtunnel into the netfilter core
seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6 behaviors
netfilter: ipset: Fix suspicious rcu_dereference_protected()
selftests: openvswitch: Set value to nla flags.
octeontx2-pf: Fix linking objects into multiple modules
octeontx2-pf: Add error handling to VLAN unoffload handling
virtio_net: fixing XDP for fully checksummed packets handling
virtio_net: checksum offloading handling fix
...
Pull sound fixes from Takashi Iwai:
"Lots of small HD-audio quirks and fixes (mostly Realtek codec and
Cirrus stuff).
Also a small MIDI 2.0 fix and a fix for missing module description
are included"
* tag 'sound-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: cs35l56: Select SERIAL_MULTI_INSTANTIATE
ALSA: hda/realtek: Add more codec ID to no shutup pins list
sound/oss/dmasound: add missing MODULE_DESCRIPTION() macro
ALSA: hda/realtek: Add quirk for Lenovo Yoga Pro 7 14ARP8
ALSA: hda/realtek: Enable headset mic on IdeaPad 330-17IKB 81DM
ALSA: hda: tas2781: Component should be unbound before deconstruction
ALSA: hda: cs35l41: Component should be unbound before deconstruction
ALSA: hda: cs35l56: Component should be unbound before deconstruction
ALSA/hda: intel-dsp-config: Document AVS as dsp_driver option
ALSA: hda/realtek: Support Lenovo Thinkbook 13x Gen 4
ALSA: hda/realtek: Support Lenovo Thinkbook 16P Gen 5
ALSA: hda: cs35l41: Support Lenovo Thinkbook 13x Gen 4
ALSA: hda: cs35l41: Support Lenovo Thinkbook 16P Gen 5
ALSA: hda/realtek: Remove Framework Laptop 16 from quirks
ALSA: hda/realtek: Limit mic boost on N14AP7
ALSA: hda/realtek: fix mute/micmute LEDs don't work for ProBook 445/465 G11.
ALSA: seq: ump: Fix missing System Reset message handling
ALSA: hda: cs35l41: Possible null pointer dereference in cs35l41_hda_unbind()
ALSA: hda: cs35l56: Fix lifecycle of codec pointer
Pull mfd fix from Lee Jones:
- Fix AXP717 PMIC probe and by extension its consumers
* tag 'mfd-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: axp20x: AXP717: Fix missing IRQ status registers range
Michael Chan says:
====================
bnxt_en: Bug fixes for net
The first firmware interface update is needed by the second patch to
limit the number of TSO segments on the 5760X chips. The third patch
fixes the TX error path for PTP packets.
====================
Link: https://lore.kernel.org/r/20240618215313.29631-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign the configured channel value to the EXTTS event in the timestamp
interrupt handler. Without assigning the correct channel, applications
like ts2phc will refuse to accept the event, resulting in errors such
as:
...
ts2phc[656.834]: config item end1.ts2phc.pin_index is 0
ts2phc[656.834]: config item end1.ts2phc.channel is 3
ts2phc[656.834]: config item end1.ts2phc.extts_polarity is 2
ts2phc[656.834]: config item end1.ts2phc.extts_correction is 0
...
ts2phc[656.862]: extts on unexpected channel
ts2phc[658.141]: extts on unexpected channel
ts2phc[659.140]: extts on unexpected channel
Fixes: f4da56529d ("net: stmmac: Add support for external trigger timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20240618073821.619751-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
Patch #1 fixes the suspicious RCU usage warning that resulted from the
recent fix for the race between namespace cleanup and gc in
ipset left out checking the pernet exit phase when calling
rcu_dereference_protected(), from Jozsef Kadlecsik.
Patch #2 fixes incorrect input and output netdevice in SRv6 prerouting
hooks, from Jianguo Wu.
Patch #3 moves nf_hooks_lwtunnel sysctl toggle to the netfilter core.
The connection tracking system is loaded on-demand, this
ensures availability of this knob regardless.
Patch #4-#5 adds selftests for SRv6 netfilter hooks also from Jianguo Wu.
netfilter pull request 24-06-19
* tag 'nf-24-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
selftests: add selftest for the SRv6 End.DX6 behavior with netfilter
selftests: add selftest for the SRv6 End.DX4 behavior with netfilter
netfilter: move the sysctl nf_hooks_lwtunnel into the netfilter core
seg6: fix parameter passing when calling NF_HOOK() in End.DX4 and End.DX6 behaviors
netfilter: ipset: Fix suspicious rcu_dereference_protected()
====================
Link: https://lore.kernel.org/r/20240619170537.2846-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ACPI IDs used in the CS35L56 HDA drivers are all handled by the
serial multi-instantiate driver which starts multiple Linux device
instances from a single ACPI Device() node.
As serial multi-instantiate is not an optional part of the system add it
as a dependency in Kconfig so that it is not overlooked.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://lore.kernel.org/20240619161602.117452-1-simont@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding/updating VSI list rule, as well as allocating/freeing VSI list
resource are called several times with type ICE_SW_LKUP_LAST, which fails
because ice_update_vsi_list_rule() and ice_aq_alloc_free_vsi_list()
consider it invalid. Allow calling these functions with ICE_SW_LKUP_LAST.
This fixes at least one issue in switchdev mode, where the same rule with
different action cannot be added, e.g.:
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF1_PR
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF2_PR
Fixes: 0f94570d0c ("ice: allow adding advanced rules")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240618210206.981885-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull probes fix from Masami Hiramatsu:
- Restrict gen-API tests for synthetic and kprobe events to only be
built as modules, as they generate dynamic events that cannot be
removed, causing ftracetest and startup selftests to fail
* tag 'probes-fixes-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Build event generation tests only as modules
this selftest is designed for evaluating the SRv6 End.DX6 behavior
used with netfilter(rpfilter), in this example, for implementing
IPv6 L3 VPN use cases.
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
this selftest is designed for evaluating the SRv6 End.DX4 behavior
used with netfilter(rpfilter), in this example, for implementing
IPv4 L3 VPN use cases.
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, the sysctl net.netfilter.nf_hooks_lwtunnel depends on the
nf_conntrack module, but the nf_conntrack module is not always loaded.
Therefore, accessing net.netfilter.nf_hooks_lwtunnel may have an error.
Move sysctl nf_hooks_lwtunnel into the netfilter core.
Fixes: 7a3f5b0de3 ("netfilter: add netfilter hooks to SRv6 data plane")
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
