Pull RTC updates from Alexandre Belloni:
"Most of the work and improvements are for features of the m41t93.
The ds1307 also gets support for OSF (Oscillator Stop Flag) for
new variants.
The pcap driver is being removed as the Motorola EZX support was
removed a while ago.
Subsystem:
- add rtc_read_next_alarm() to read next expiring timer
Drivers:
- ds1307: handle OSF for ds1337/ds1339/ds3231, add clock provider for
ds1307, fix wday for rx8130
- m41t93: DT support, alarm, clock provider, watchdog support
- mv: add suspend/resume support for wakeup
- pcap: remove driver
- renesas-rtca3: many fixes"
* tag 'rtc-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (36 commits)
rtc: ds1307: update reference to removed CONFIG_RTC_DRV_DS1307_HWMON
platform/x86: amd-pmc: Fix S0i3 wakeup with alarmtimer
rtc: s35390a: fix typo in comment
rtc: cmos: unregister HPET IRQ handler on probe failure
rtc: ds1307: Fix off-by-one issue with wday for rx8130
dt-bindings: rtc: ds1307: Add epson,rx8901
rtc: bq32000: add delay between RTC reads
rtc: m41t93: Add watchdog support
rtc: m41t93: Add square wave clock provider support
rtc: m41t93: Add alarm support
rtc: m41t93: migrate to regmap api for register access
rtc: m41t93: add device tree support
dt-bindings: rtc: Add ST m41t93
rtc: ds1307: add support for clock provider in ds1307
rtc: mv: add suspend/resume support for wakeup
rtc: aspeed: add AST2700 compatible
dt-bindings: rtc: add ASPEED AST2700 compatible
rtc: interface: fix typos in rtc_handle_legacy_irq() documentation
rtc: msc313: fix NULL deref in shared IRQ handler at probe
rtc: remove unused pcap driver
...
cmos_do_probe() registers cmos_interrupt() as the HPET RTC IRQ
handler before requesting the RTC IRQ and registering the RTC
device. If either request_irq() or devm_rtc_register_device()
fails afterwards, the error path leaves the HPET RTC IRQ handler
installed. This leaves a stale handler behind and make a later
hpet_register_irq_handler() fail with -EBUSY.
Track whether the HPET handler was registered successfully and
undo the registration on the probe error path. Also mask the HPET
RTC IRQ bits to match the normal shutdown cleanup.
Fixes: 9d8af78b07 ("rtc: add HPET RTC emulation to RTC_DRV_CMOS")
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20260623100848.2127281-1-haoxiang_li2024@163.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC represent each weekday with a individual bit set in the WDAY
register, where the 0th bit represent the first day of the week and the
6th bit represents the last day of the week. For each passed day the
chip performs a rotary-left-shift by one to advance the weekday by one.
The tm_wday field represent weekdays by a value in the range of 0-6.
The fls() function return the bit index of the last bit set. To handle
when there are no bits set it will return 0, and if the 0th bit is set
it will return 1, and if the 1st bit is set it will return 2, and so on.
In order to make the result of the fls() function fall into the expected
range of 0-6 (instead of 1-7) this patch subtracts one from the result
(which matches how the value is written in ds1307_set_time()).
Fixes: 204756f016 ("rtc: ds1307: Fix wday settings for rx8130")
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.x90@mail.toshiba>
Signed-off-by: Fredrik M Olsson <fredrik.m.olsson@axis.com>
Link: https://patch.msgid.link/20260520-ds1307-rx8901-add-v2-2-e069ea32e1db@axis.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the RTC is used on systems without a interrupt line, userspace
tools like `hwclock` fall back to a frequent polling loop to synchronize
with the edge of the next second.
On the BQ32000, this aggressive polling can temporarly lock the register
refresh cycle, because the continuous transfers prevent the hardware from
updating the buffer. This results in stale data reads or select() timeouts
in userspace.
This patch introduces a delay before reading the RTC registers in order to
provide a sufficient idle time for the hardware to sync with the register
buffer.
Signed-off-by: Adriana Stancu <adriana@arista.com>
Link: https://patch.msgid.link/20260416142151.3385827-1-adriana@arista.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement support to configure square wave output (SQW) of m41t93 rtc
via common clock framework clock provider api. Add clock provider
callbacks to control output frequency ranging from 1Hz to 32KHz as
supported by this rtc chip.
Use clock framework debugfs interface or clock consumer DT node to test.
Tested by measuring various frequencies on pull-up connected SWQ(7) pin
of m41t93 rtc chip using logic analyzer.
Signed-off-by: Akhilesh Patil <akhilesh@ee.iitb.ac.in>
Link: https://patch.msgid.link/a8c4d3741be4e9dfa52c57cbd653f561ba4ed934.1758379856.git.akhilesh@ee.iitb.ac.in
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement alarm feature for rtc-m41t93 by adding necessary
callbacks - set_alarm, read_alarm and alarm_irq_enable.
Enable support to configure alarm 1 out of 2 alarms present in this rtc.
Support only alarm configuration in this commit. This commit does not
implement alarm irq handling.
Use selftests/rtc/rtctest for testing. Tested by observing IRQ pin
(pin 12 of SOX18 package) on logic analyzer going low after alarm
condition is met.
Signed-off-by: Akhilesh Patil <akhilesh@ee.iitb.ac.in>
Link: https://patch.msgid.link/1b272ff1a5392d5eb76e129a4785ac8424763356.1758379856.git.akhilesh@ee.iitb.ac.in
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Adapt driver to use regmap api with spi bus instead of direct spi
subsystem calls to access device registers. Simplify and standardize the
register interactions using more abstract and bus agnostic regmap api
to reduce code duplication and improve maintainability. Define spi regmap
config suitable for m41t93 spi bus protocol to achieve same transactions on
spi bus.
Tested on TI am62x sk board with m41t93 rtc chip connected over spi0.
Validated set and get time using hwclock tool and verified spi bus
transfers using logic analyzer.
Signed-off-by: Akhilesh Patil <akhilesh@ee.iitb.ac.in>
Link: https://patch.msgid.link/180f9b6c3ee7c490fe3537c2d50a92cec359e4cd.1758379856.git.akhilesh@ee.iitb.ac.in
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add PM suspend/resume callbacks to enable/disable IRQ wake for the
RTC alarm interrupt. This allows the RTC alarm to wake the system
from STR (e.g. via rtcwake -m mem -s N).
Without this, the RTC IRQ is masked during suspend by the MPIC's
IRQCHIP_MASK_ON_SUSPEND behavior, preventing alarm-based wakeup.
Signed-off-by: Xue Lei <Xue.Lei@windriver.com>
Link: https://patch.msgid.link/20260611023350.1370881-1-Xue.Lei@windriver.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
msc313_rtc_probe() calls devm_request_irq() with IRQF_SHARED and
&pdev->dev as the cookie, but platform_set_drvdata() is only called
later after the clock setup. With a shared IRQ line, another device
on the same line can trigger the handler in that window. The
handler does dev_get_drvdata() on the cookie, gets NULL, and
dereferences priv->rtc_base in interrupt context.
Pass priv as the cookie directly so the handler reads it from
dev_id without the lookup, removing the dependency on probe order.
Fixes: be7d9c9161 ("rtc: Add support for the MSTAR MSC313 RTC")
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Link: https://patch.msgid.link/20260511032703.48262-1-sozdayvek@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a new function rtc_read_next_alarm() that reads the next expiring
alarm from the RTC timerqueue. This is different from rtc_read_alarm(),
which only reads the aie_timer.
The wakealarm sysfs file programs the rtc->aie_timer, whereas the
alarmtimer suspend routine programs its own timer into the RTC timerqueue.
Both timers end up in the RTC's timerqueue, and the first expiring timer
is what gets armed in the hardware.
This new function allows code to query which alarm will actually fire
next, regardless of which subsystem programmed it. This is needed by
platform code that needs to program secondary timers based on the
actual next wakeup time.
Link: https://lore.kernel.org/all/87ed50z0le.ffs@tglx
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20260521043714.1022930-2-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
isl1208_setup_irq() calls enable_irq_wake() after a successful
IRQ request, but the driver has no remove path that balances it.
The driver is devm-only, so on unbind devm releases the IRQ -
but enable_irq_wake() is not undone by IRQ release, so the wake
count for that IRQ stays incremented.
Each rebind therefore leaks one wake reference; the leak doubles
for the chip variant that has a separate evdet IRQ, since
isl1208_setup_irq() is then called twice during probe.
Register a devm action that calls disable_irq_wake() per IRQ.
While at it, check enable_irq_wake()'s return value:
on failure, propagate the error rather than silently registering
a disable action for an IRQ whose wake state was never enabled.
Fixes: 9ece7cd833 ("rtc: isl1208: Add "evdet" interrupt source for isl1219")
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Link: https://patch.msgid.link/20260425154959.2796261-3-john.madieu.xa@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify usage of whitespace and commas.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Tóth János <gomba007@gmail.com>
Link: https://patch.msgid.link/20260515154720.406128-2-u.kleine-koenig@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Prior to commit 4845865465 ("rtc: ds1307: remove clear of oscillator
stop flag (OSF) in probe"), the oscillator stop flag (OSF) bit was
checked during device probe for the ds1337, ds1339, ds1341, and ds3231
chips; if it was set, it would be cleared and a warning would be logged
saying "SET TIME!". Since that commit, the OSF bit is no longer cleared,
but the warning is still printed.
Directly following that commit, there was no way to get rid of this
warning because nothing cleared the OSF bit on these chips.
The commit associated with the previous commit, 523923cfd5 ("rtc:
ds1307: handle oscillator stop flag (OSF) for ds1341"), made proper use
of the OSF when getting and setting the time in the RTC. However, the
other RTC variants ds1337, ds1339 and ds3231 didn't have a corresponding
change made.
Given that the OSF bit is no longer cleared at probe time when it is
set, the remaining three chips should have the same handling as the
ds1341 chip has for the OSF bit.
Fix the issue on the ds1337, ds1339 and ds3231 chips by applying the
same logic as the ds1341 has to these chips.
Note that any devices brought up between the first referenced commit and
this one may begin mistrusting the time reported by the RTC until it is
set again, if the bit was never explicitly cleared.
Note that only the ds1339 was tested with this change, but the
datasheets for the other chips contain essentially identical
descriptions of the OSF bit so the same change should work.
Signed-off-by: Ronan Dalton <ronan.dalton@alliedtelesis.co.nz>
Cc: linux-rtc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Tyler Hicks <code@tyhicks.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Meagan Lloyd <meaganlloyd@linux.microsoft.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Fixes: 4845865465 ("rtc: ds1307: remove clear of oscillator stop flag (OSF) in probe")
Reviewed-by: Meagan Lloyd <meaganlloyd@linux.microsoft.com>
Reviewed-by: Tyler Hicks <code@tyhicks.com>
Link: https://patch.msgid.link/20260508032518.3696705-2-ronan.dalton@alliedtelesis.co.nz
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The condition that needs to be checked for upload completion is the
UPLOAD bit in the completion register going low. The original iterations
of this driver used a do-while and this was converted to a
read_poll_timeout() during upstreaming without the condition being
inverted as it should have been.
I suspect that this went unnoticed until now because a) the first read
was done when the bit was still set, immediately completing the
read_poll_timeout() and b) because the RTC doesn't hold time when power
is removed from the SoC reducing its utility (I for one keep it
disabled). If my first suspicion was true when the driver was
upstreamed, it's not true any longer though, hence the detection of the
problem.
Fixes: 0b31d70359 ("rtc: Add driver for Microchip PolarFire SoC")
CC: stable@vger.kernel.org
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Valentina Fernandez <valentina.fernandezalanis@microchip.com>
Link: https://patch.msgid.link/20260513-panhandle-ashy-70c6abf84d59@spud
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC_VL_CLR ioctl intends to clear only the battery low flag (BLF),
however the current implementation writes 0 to the status register,
clearing all status bits.
Fix this by writing back the masked status value so that only BLF is
cleared, preserving other status flags.
Fixes: ffe1c5a2d4 ("rtc: abx80x: Implement RTC_VL_READ,CLR ioctls")
Signed-off-by: Antoni Pokusinski <apokusinski01@gmail.com>
Link: https://patch.msgid.link/20260415160610.127155-2-apokusinski01@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In rtca3_set_alarm(), the setup_failed path attempts to disable the
Periodic Interrupt Enable (PIE) bit and wait until it is cleared.
However, the polling condition passed to readb_poll_timeout_atomic()
uses an incorrect expression:
!(tmp & ~RTCA3_RCR1_PIE)
As ~RTCA3_RCR1_PIE evaluates to a mask of all bits except PIE, the
condition effectively waits for all non-PIE bits to become zero, which
is unrelated to the intended operation and is unlikely to ever be true.
This causes the poll to time out unnecessarily.
Fix the condition to check for the PIE bit itself being cleared:
!(tmp & RTCA3_RCR1_PIE)
This correctly waits until PIE is deasserted after being cleared.
Fixes: d448837760 ("rtc: renesas-rtca3: Add driver for RTCA-3 available on Renesas RZ/G3S SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> # on RZ/G3S
Link: https://patch.msgid.link/20260602192559.1791344-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch from sign_extend32(FIELD_GET()) to the dedicated
FIELD_GET_SIGNED() and don't calculate the fields length explicitly.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Yury Norov <ynorov@nvidia.com>
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode"
* tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: Disable alarm feature if no interrupt attached
rtc: ntxec: fix OF node reference imbalance
rtc: pic32: allow driver to be compiled with COMPILE_TEST
rtc: ti-k3: Add support to resume from IO DDR low power mode
rtc: cmos: Use platform_get_irq_optional() in cmos_platform_probe()
dt-bindings: rtc: add olpc,xo1-rtc to trivial-rtc
dt-bindings: rtc: sc2731: Add compatible for SC2730
rtc: add data_race() in rtc_dev_poll()
rtc: armada38x: zalloc + calloc to single allocation
dt-bindings: rtc: isl12026: convert to YAML schema
dt-bindings: rtc: microcrystal,rv3028: Allow to specify vdd-supply
rtc: max77686: convert to i2c_new_ancillary_device
dt-bindings: rtc: mpfs-rtc: permit resets
rtc: rx8025: Remove use of i2c_match_id()
rtc: rv8803: Remove use of i2c_match_id()
rtc: rs5c372: Remove use of i2c_match_id()
rtc: pcf2127: Remove use of i2c_match_id()
rtc: m41t80: Remove use of i2c_match_id()
rtc: abx80x: Remove use of i2c_match_id()
Commit 795cda8338 ("rtc: interface: Fix long-standing race when setting
alarm") exposed an issue where the rtc-abx80x driver does not clear the
alarm feature bit, but instead relies on the set_alarm operation to return
invalid.
For example, when a RTC_UIE_ON ioctl is handled, it should abort at the
feature validation. Instead, it proceeds to the rtc_timer_enqueue(),
which used to return an error from the set_alarm call. However,
following the race condition handling, which likely should not be
discarding predecing errors, a success condition is returned to the
ioctl() caller. This results in (for example):
hwclock: select() to /dev/rtc0 to wait for clock tick timed out
Notwithstanding the validity of the race condition handling, if an interrupt
wasn't specified, or could not be attached, the driver should clear the
alarm feature bit.
Fixes: 718a820a30 ("rtc: abx80x: add alarm support")
Signed-off-by: Anthony Pighin <anthony.pighin@nokia.com>
Link: https://patch.msgid.link/BN0PR08MB69510928028C933749F4139383D1A@BN0PR08MB6951.namprd08.prod.outlook.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This driver currently only supports builds against a PIC32 target. Now
that commit ed65ae9f6c ("rtc: pic32: update include to use pic32.h
from platform_data") is merged, it's possible to compile this driver on
other architectures.
To avoid future breakage of this driver in the future, let's update the
Kconfig so that it can be built with COMPILE_TEST enabled on all
architectures.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://patch.msgid.link/20260222-rtc-pic32-v1-1-3f8eb654a34d@redhat.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If the ACPI_FADT_FIXED_RTC flag is unset, the platform is declaring that
it supports the ACPI RTC fixed event which should be used instead of a
dedicated CMOS RTC IRQ. However, the driver only enables it when
is_hpet_enabled() returns true, which is questionable because there is
no clear connection between enabled HPET and signaling wakeup via the
ACPI RTC fixed event (for instance, the latter can be expected to work
on systems that don't include a functional HPET).
Moreover, since use_hpet_alarm() returns false if use_acpi_alarm is set,
the ACPI RTC fixed event is effectively used instead of the HPET alarm
if the latter is functional, but there is no particular reason why it
could not be used otherwise.
Accordingly, on x86 systems with ACPI, set use_acpi_alarm if
ACPI_FADT_FIXED_RTC is unset without looking at whether or not HPET is
enabled.
Also, do the ACPI FADT check in use_acpi_alarm_quirks() before the DMI
BIOS year checks which are more expensive and it's better to skip them
if ACPI_FADT_FIXED_RTC is set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/9618535.CDJkKcVGEf@rafael.j.wysocki
The rtc-cmos driver can live without an IRQ and returning an error
code from platform_get_irq() is not a problem for it in general, so
make it call platform_get_irq_optional() in cmos_platform_probe()
instead of platform_get_irq() to avoid a confusing error message
printed by the latter if an IRQ cannot be found for index 0, which
is possible on x86 platforms.
Additionally, on x86, if the IRQ is not defined and the system has
a legacy PIC, hardcode it to RTC_IRQ, which should be safe then (and
which is what the dropped PNP code did).
Fixes: d15f1c2e41 ("ACPI: PNP: Drop CMOS RTC PNP device support")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/linux-acpi/20260303060752.GA2749263@ax162/
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/12857714.O9o76ZdvQC@rafael.j.wysocki
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Convert RTC I2C device creation from devm_i2c_new_dummy_device() to
i2c_new_ancillary_device() to enable the use of a device tree-specified
RTC address instead of a hardcoded value. If the device tree does not
provide an address, use hardcoded values as a fallback.
This addresses an issue with the MAX77663 PMIC, which can have the RTC at
different I2C positions (either 0x48, like the MAX77714, or 0x68, like
the MAX77620). The MAX77620 value is used as the default. The I2C position
of the MAX77663 is factory-set and cannot be detected from the chip
itself.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260312085258.11431-6-clamor95@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20260305193545.796294-7-afd@ti.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20260305193545.796294-6-afd@ti.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20260305193545.796294-5-afd@ti.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20260305193545.796294-4-afd@ti.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20260305193545.796294-3-afd@ti.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
