Revert commit 690de2902d ("i2c: muxes: pca954x: Use reset controller
only") and its dependent commit 94c2967764 ("i2c: muxes: pca954x:
Reset if (de)select fails") because the first breaks all users of the
driver, by requiring a completely optional reset-gpio driver. These
commits cause that mux driver simply stops working when optional
reset-gpio is not included, but that reset-gpio is not pulled anyhow.
Driver cannot remove legacy reset-gpios handling.
Fixes: 690de2902d ("i2c: muxes: pca954x: Use reset controller only")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Remove existing arbitration timeout macros and use I2C adapter timeout
value for arbitration timeout and forceful bus ownership.
I2C adapter timeout can be configurable from user space, so using it
for arbitration timeout helps in configuring the arbitration timeout
from user space depending on the use case.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
If the channel selection or deselection times out, it indicates
a failure in the mux's I2C subsystem. Without sending a reset pulse,
a power-on-reset of the entire device would be required to restore
communication.
The datasheet specifies a minimum hold time of 4 ns for the reset
pulse, but due to the path's capacitance and themux having its own
clock, it is recommended to extend this to approximately 1 us.
Since reset controller is used, there is no need to take care of other
devices sharing the same reset line.
Signed-off-by: Wojciech Siudy <wojciech.siudy@nokia.com>
[wsa: removed superfluous prinout, unneeded braces and fixed indent]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fallback to legacy reset-gpios is no more needed, because the framework
can use reset-gpios properity now as well.
Signed-off-by: Wojciech Siudy <wojciech.siudy@nokia.com>
[wsa: fixed whitespace issue]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
If an error occurs in the loop that creates the device adapters, then a
reference to 'dev' still needs to be released.
Use for_each_child_of_node_scoped() to both fix the issue and save one line
of code.
Fixes: d0f8e97866 ("i2c: muxes: add support for tsd,mule-i2c multiplexer")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
irq_domain_create_simple() takes fwnode as the first argument. It can be
extracted from the struct device using dev_fwnode() helper instead of
using of_node with of_fwnode_handle(). So use the dev_fwnode() helper.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
[wsa: proper commit header]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Convert the I2C subsystem to drop using the 'master_'-prefixed callbacks
in favor of the simplified ones. Fix alignment of '=' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Pull i2c updates from Wolfram Sang:
"Core updates:
- move towards using the 'fwnode' handle instead of 'of_node'
(meaning 'of_node' even gets removed from i2c_board_info)
- add support for Write Disable-aware SPD eeproms
- minor stuff (use new helpers, typo fixes)
i2c-atr (address translator) updates:
- support per-channel alias pools
- added support for dynamic address translation (also adds FPC202
driver as its user)
- add 'static' and 'passthrough' flags
Cleanups and refactorings
- Many drivers switched to dev_err_probe()
- Generic cleanups applied to designware, iproc, ismt, mlxbf,
npcm7xx, qcom-geni, pasemi, and thunderx
- davinci: declare I2C mangling support among I2C features
- designware: clean up DTS handling
- designware: fix PM runtime on driver unregister
- imx: improve error logging during probe
- lpc2k: improve checks in probe error path
- xgene-slimpro: improve PCC shared memory handling
- pasemi: improve error handling in reset, smbus clear, timeouts
- tegra: validate buffer length during transfers
- wmt: convert binding to YAML format
Improvements and extended support:
- microchip-core: add SMBus support
- mlxbf: add support for repeated start in block transfers
- mlxbf: improve timer configuration
- npcm: attempt clock toggle recovery before failing init
- octeon: add support for block mode operations
- pasemi: add support for unjam device feature
- riic: add support for bus recovery
New device support:
- MediaTek Dimensity 1200 (MT6893)
- Sophgo SG2044
- Renesas RZ/V2N (R9A09G056)
- Rockchip RK3528
- AMD ISP (new driver)"
* tag 'i2c-for-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (89 commits)
i2c: Use str_read_write() helper
i2c: mlxbf: avoid 64-bit division
i2c: viai2c-wmt: Replace dev_err() with dev_err_probe() in probe function
i2c: designware: Don't warn about missing get_clk_rate_khz
i2c: designware: Invoke runtime suspend on quick slave re-registration
i2c-mlxbf: Improve I2C bus timing configuration
i2c-mlxbf: Add repeated start condition support
i2c: xgene-slimpro: Replace dev_err() with dev_err_probe() in probe function
dt-bindings: i2c: i2c-wmt: Convert to YAML
i2c: microchip-corei2c: add smbus support
i2c: mlxbf: Allow build with COMPILE_TEST
i2c: I2C_DESIGNWARE_AMDISP should depend on DRM_AMD_ISP
i2c: atr: add passthrough flag
i2c: atr: add static flag
i2c: atr: allow replacing mappings in attach_addr()
i2c: atr: deduplicate logic in attach_addr()
i2c: atr: do not create mapping in detach_addr()
i2c: atr: split up i2c_atr_get_mapping_by_addr()
i2c: atr: find_mapping() -> get_mapping()
i2c: atr: Fix lockdep for nested ATRs
...
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-20-jirislaby@kernel.org
i2c-host updates for v6.15
Refactoring and cleanups
- octeon, cadence, i801, pasemi, mlxbf, bcm-iproc: general
refactorings
- octeon: remove 10-bit address support
Improvements
- amd-asf: improved error handling
- designware: use guard(mutex)
- amd-asf, designware: update naming to follow latest specs
- cadence: fix cleanup path in probe
- i801: use MMIO and I/O mapping helpers to access registers
- pxa: handle error after clk_prepare_enable
New features
- added i2c_10bit_addr_*_from_msg() and updated multiple drivers
- omap: added multiplexer state handling
- qcom-geni: update frequency configuration
- qup: introduce DMA usage policy
New hardware support
- exynos: add support for Samsung exynos7870
- k1: add support for spacemit k1 (new driver)
- imx: add support for i.mx94 lpi2c
- rk3x: add support for rk3562
Multiplexers
- ltc4306, reg: fix assignment in platform_driver structure
Building with W=1 shows a warning about ltc4306_of_match and
i2c_mux_reg_of_match being unused when CONFIG_OF is disabled:
drivers/i2c/muxes/i2c-mux-ltc4306.c:200:34: error: unused variable 'ltc4306_of_match' [-Werror,-Wunused-const-variable]
drivers/i2c/muxes/i2c-mux-reg.c:242:34: error: unused variable 'i2c_mux_reg_of_match' [-Werror,-Wunused-const-variable]
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250225163700.4169480-1-arnd@kernel.org
When misconfigured, the initial setup of the current mux channel can
fail, too. It must be checked as well.
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/i2c to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
If dev_get_regmap() fails, it returns NULL pointer not ERR_PTR(),
replace IS_ERR() with NULL pointer check, and return -ENODEV.
Fixes: d0f8e97866 ("i2c: muxes: add support for tsd,mule-i2c multiplexer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Theobroma Systems Mule is an MCU that emulates a set of I2C devices,
among which an amc6821 and devices that are reachable through an I2C-mux.
The devices on the mux can be selected by writing the appropriate device
number to an I2C config register (amc6821 reg 0xff).
This driver is expected to be probed as a platform device with amc6821
as its parent i2c device.
Add support for the mule-i2c-mux platform driver. The amc6821 driver
support for the mux will be added in a later commit.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Farouk Bouabid <farouk.bouabid@cherry.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some hardware need some time to switch from a bus to another. This can
cause the first transfers following the selection of a bus to fail.
There is no way to configure this kind of waiting time in the driver.
Add support for the 'settle-time-us' device-tree property. When set,
the i2c_mux_gpio_select() applies a delay before returning, leaving
enough time to the hardware to switch to the new bus.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove a comma after the sentinel entry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
99a741aa7a2d ("i2c: mux: gpio: remove support for class-based device
instantiation") removed the last call to i2c_mux_add_adapter() with a
non-null class argument. Therefore the class argument can be removed.
Note: Class-based device instantiation is a legacy mechanism which
shouldn't be used in new code, so we can rule out that this argument
may be needed again in the future.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
i801 as only user of gpio i2c mux removed support for class-based device
instantiation on muxed busses. Class-based device instantiation is a
legacy mechanism and shouldn't be used in new code, therefore remove
support also here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Some hardware designs with multiple PCA954x devices use a reset GPIO
connected to all the muxes. Support this configuration by making use of
the reset controller framework which can deal with the shared reset
GPIOs. Fall back to the old GPIO descriptor method if the reset
controller framework is not enabled.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Pull i2c updates from Wolfram Sang:
"Minor changes to the I2C core. Most changes are in drivers:
The i801 and designware drivers received most of the changes,
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations, such as
isolating faulty channels and flushing stuck buses, among others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming R-Car Gen4"
* tag 'i2c-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: sprd: Convert to platform remove callback returning void
Documentation: i2c: Document that client auto-detection is a legacy mechanism
i2c: remove redundant condition
i2c: rcar: Prepare for the advent of ARCH_RCAR_GEN4
i2c: imx-lpi2c: add generic GPIO recovery for LPI2C
i2c: cadence: Add system suspend and resume PM support
i2c: mpc: remove outdated macro
i2c: mpc: use proper binding for transfer timeouts
dt-bindings: i2c: mpc: use proper binding for transfer timeouts
i2c: smbus: Prepare i2c_register_spd for usage on muxed segments
i2c: constify the struct device_type usage
i2c: designware: Implement generic polling mode code for Wangxun 10Gb NIC
i2c: designware: Fix RX FIFO depth define on Wangxun 10Gb NIC
i2c: designware: Move interrupt handling functions before i2c_dw_xfer()
i2c: designware: Use accessors to DW_IC_INTR_MASK register
i2c: designware: Do not enable interrupts shortly in polling mode
i2c: designware: Uniform initialization flow for polling mode
dt-bindings: i2c: at91: Add sam9x7 compatible string
dt-bindings: i2c: imx-lpi2c: add i.MX95 LPI2C
i2c: Remove redundant comparison in npcm_i2c_reg_slave
...
Found with git grep 'MODULE_AUTHOR(".*([^)]*@'
Fixed with
sed -i '/MODULE_AUTHOR(".*([^)]*@/{s/ (/ </g;s/)"/>"/;s/)and/> and/}' \
$(git grep -l 'MODULE_AUTHOR(".*([^)]*@')
Also:
in drivers/media/usb/siano/smsusb.c normalise ", INC" to ", Inc";
this is what every other MODULE_AUTHOR for this company says,
and it's what the header says
in drivers/sbus/char/openprom.c normalise a double-spaced separator;
this is clearly copied from the copyright header,
where the names are aligned on consecutive lines thusly:
* Linux/SPARC PROM Configuration Driver
* Copyright (C) 1996 Thomas K. Dyas (tdyas@noc.rutgers.edu)
* Copyright (C) 1996 Eddie C. Dost (ecd@skynet.be)
but the authorship branding is single-line
Link: https://lkml.kernel.org/r/mk3geln4azm5binjjlfsgjepow4o73domjv6ajybws3tz22vb3@tarta.nabijaczleweli.xyz
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Enable additional features based on DT settings and unconditionally
release the shared interrupt pin after 1.6 seconds and allow to use
it as reset.
These features aren't enabled by default and it's up to board designer
to validate for proper functioning and detection of devices in secondary
bus as sometimes it can cause secondary bus being disabled.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has largely driver updates for 6.7, i.e. feature additions (like
adding transfers while in atomic mode), using new helpers (like
devm_clk_get_enabled), new IDs, documentation fixes and additions...
you name it.
The core got a memleak fix and better support for nested muxes"
* tag 'i2c-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: s3c2410: make i2c_s3c_irq_nextbyte() void
i2c: qcom-geni: add ACPI device id for sc8180x
Documentation: i2c: add fault code for not supporting 10 bit addresses
i2c: sun6i-p2wi: Prevent potential division by zero
i2c: mux: demux-pinctrl: Convert to use sysfs_emit_at() API
i2c: i801: Use new helper acpi_use_parent_companion
ACPI: Add helper acpi_use_parent_companion
MAINTAINERS: add YAML file for i2c-demux-pinctrl
i2c: core: fix lockdep warning for sparsely nested adapter chain
i2c: axxia: eliminate kernel-doc warnings
dt-bindings: i2c: i2c-demux-pinctrl: Convert to json-schema
i2c: stm32f7: Use devm_clk_get_enabled()
i2c: stm32f4: Use devm_clk_get_enabled()
i2c: stm32f7: add description of atomic in struct stm32f7_i2c_dev
i2c: fix memleak in i2c_new_client_device()
i2c: exynos5: Calculate t_scl_l, t_scl_h according to i2c spec
i2c: i801: Simplify class-based client device instantiation
i2c: exynos5: add support for atomic transfers
i2c: at91-core: Use devm_clk_get_enabled()
eeprom: at24: add ST M24C64-D Additional Write lockable page support
...
Pull gpio updates from Bartosz Golaszewski:
"We don't have any new drivers. The loongson driver is getting extended
with support for new models. There's a big refactor of gpio-pca953x
and many small improvements to others.
The GPIO code in the kernel has acquired a lot of cruft over the years
as well as many abusers of the API across the kernel tree. This
release cycle we have started a major cleanup and improvement effort
that will most likely span several releases. We have started by
converting external users of struct gpio_chip to accessing the wrapper
around it - struct gpio_device. This is because the latter is
reference counted while the former is removed when the provider is
unbound. We also removed several instances of drivers accessing
private GPIOLIB structures and including the private header from
drivers/gpio/.
To that end you'll see several commits aimed at different subsystems
(acked by relevant maintainers) as well as two merges from the
x86/platform tree.
We'll then rework the locking in GPIOLIB which currently uses a big
spinlock for many different things and could use becoming more
fine-grained, especially as it doesn't even get the locking right.
We'll also use SRCU for protecting the gpio_chip pointer against
in-kernel hot-unplug crashes similar to what we saw triggered from
user-space and fixed with semaphores in gpiolib-cdev. The core GPIOLIB
is still vulnerable to these use-cases. I'm just mentioning the plans
here, this is not part of this PR.
You'll see some new instances of using __free(). We've added a
gpio_device_put cleanup helper similar to the put_device one
introduced by Peter Zijlstra and used it according to the preferred
pattern except where it didn't make sense.
GPIOLIB core:
- provide interfaces allowing users to retrieve, manage and query the
reference counted GPIO device instead of accessing the private
gpio_chip structure
- replace gpiochip_find() with gpio_device_find()
- remove unused acpi_get_and_request_gpiod()
- improve the ignore_interrupt functionality in GPIO ACPI
- correct notifier return codes in gpiolib-of
- unexport gpiod_set_transitory() as it's unused outside of core GPIO
code
- while there are still external users accessing struct gpio_chip,
let's make gpiochip_get_desc() public so that they at least use the
preferred helper
- improve locking for lookup tables
- annotate struct linereq with __counted_by
- improve GPIOLIB docs
- add an OF quirk for LED trigger sources
Driver improvements:
- convert all GPIO drivers with .remove() callbacks to using the new
variant returning void instead of int
- stop accessing the GPIOLIB private structures in gpio-mockup,
i2c-mux-gpio, hte-tegra194, gpio-sim
- use the recommended pattern for autofree variables in gpio-sim
- add support for more models to gpio-loongson
- use a notifier chain to notify other blocks about interrupts in
gpio-eic-sprd instead of looking up GPIO devices on every interrupt
- convert gpio-pca953x and gpio-fx6408 to using the maple tree regmap
cache
- don't include GPIOLIB internal headers in drivers which don't need
them
- move the ingenic NAND quirk into gpiolib-of
- add an ignore interrupt quirk for Peaq C1010
- drop static GPIO base from gpio-omap, gpio-f7188x
- use the preferred device_get_match_data() function in drivers that
still don't
- refactor gpio-pca953x: switch to using DEFINE_SIMPLE_DEV_PM_OPS(),
use cleanup helpers, use dev_err_probe() where it makes sense,
fully convert to using devres and some other minor tweaks
DT bindings:
- add support for a new model to gpio-vf610 and update existing
properties
- add support for more loongson models
- add missing support for imx models that are used but undocumented
- convert bindings for Intel IXP4xx to schema
Minor stuff:
- deprecate gpio-mockup in favor of gpio-sim
- include missing headers here and there
- stop using gpiochip_find() in OMAP1 board files
- minor tweaks in gpio-vf610, gpio-hisi
- remove unneeded 'extern' specifiers from headers"
* tag 'gpio-updates-for-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (108 commits)
hte: tegra194: add GPIOLIB dependency
hte: tegra194: don't access struct gpio_chip
gpiolib: provide gpio_device_get_base()
i2c: mux: gpio: don't fiddle with GPIOLIB internals
gpiolib: provide gpiod_to_gpio_device()
gpiolib: provide gpio_device_to_device()
gpio: hisi: Fix format specifier
gpiolib: provide gpio_device_find_by_fwnode()
gpio: acpi: remove acpi_get_and_request_gpiod()
gpio: Use device_get_match_data()
gpio: vf610: update comment for i.MX8ULP and i.MX93 legacy compatibles
platform/x86: int3472: Switch to devm_get_gpiod()
platform/x86: int3472: Stop using gpiod_toggle_active_low()
platform/x86: int3472: Add new skl_int3472_gpiod_get_from_temp_lookup() helper
platform/x86: int3472: Add new skl_int3472_fill_gpiod_lookup() helper
gpio: vf610: simplify code by dropping data check
gpio: vf610: add i.MX8ULP of_device_id entry
dt-bindings: gpio: vf610: add i.MX95 compatible
dt-bindings: gpio: vf610: correct i.MX8ULP and i.MX93
dt-bindings: gpio: vf610: update gpio-ranges
...
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: proper subject prefix]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: ac8498f0ce ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: c4aee3e1b0 ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use the relevant API functions to retrieve the address of the
underlying struct device instead of accessing GPIOLIB private structures
manually.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct i2c_demux_pinctrl_priv.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[wsa: improved blank lines]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In i2c_mux_gpio_probe_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 98b2b712bc ("i2c: i2c-mux-gpio: Enable this driver in ACPI land")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac0 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for the following Maxim chips using the existing PCA954x
driver:
- MAX7356
- MAX7357
- MAX7358
- MAX7367
- MAX7368
- MAX7369
All added Maxim chips behave like the PCA954x, where a single SMBUS byte
write selects up to 8 channels to be bridged to the primary bus.
While the MAX7357/MAX7358 have interrupt support, they don't act as
interrupt controller like the PCA9545 does. Thus don't enable IRQ support
and handle them like the PCA9548.
Tested using the MAX7357.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use the new PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230722115310.27681-6-paul@crapouillou.net
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Now that .probe() was changed not to get the id parameter, drivers can
be converted back to that with the eventual goal to drop .probe_new().
Implement that for the i2c mux drivers.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It will cause null-ptr-deref in resource_size(), if platform_get_resource()
returns NULL, move calling resource_size() after devm_ioremap_resource() that
will check 'res' to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: b3fdd32799 ("i2c: mux: Add register-based mux i2c-mux-reg")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
