The System Management Controller on Apple Silicon devices is responsible
for integrating and exposing the data reported by the vast array of
hardware monitoring sensors present on these devices. It is also
responsible for fan control, and allows users to manually set fan
speeds if they so desire. Add a hwmon driver to expose current,
power, temperature, and voltage monitoring sensors, as well as
fan speed monitoring and control via the SMC on Apple Silicon devices.
The SMC firmware has no consistency between devices, even when they
share an SoC. The FourCC keys used to access sensors are almost
random. An M1 Mac mini will have different FourCCs for its CPU core
temperature sensors to an M1 MacBook Pro, for example. For this
reason, the valid sensors for a given device are specified in a
child of the SMC Devicetree node. The driver uses this information
to determine which sensors to make available at runtime.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Co-developed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://lore.kernel.org/r/20251112-macsmc-subdevs-v5-6-728e4b91fe81@gmail.com
[groeck: Added Documentation to index]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a driver for the ST Microelectronics TSC1641 16-bit high-precision
power monitor. The driver supports reading bus voltage, current, power,
and temperature. Sysfs attributes are exposed for shunt resistor and
update interval. The driver integrates with the hwmon subsystem and
supports optional ALERT pin polarity configuration.
Signed-off-by: Igor Reznichenko <igor@reznichenko.net>
Link: https://lore.kernel.org/r/20251105201406.1210856-3-igor@reznichenko.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull gpio updates from Bartosz Golaszewski:
"There are two new drivers and support for more models in existing
ones.
The generic GPIO API has been reworked and all users converted
which allowed us to move the fields specific to the generic GPIO
implementation out of the high-level struct gpio_chip into its own
structure that wraps the gpio_chip.
Other than that, there's nothing too exciting. Mostly minor tweaks and
fixes all over the place, some refactoring and some small new features
in helper modules.
GPIO core:
- add support for sparse pin ranges to the glue between GPIO and
pinctrl
- use a common prefix across all GPIO descriptor flags for improved
namespacing
New drivers:
- add new GPIO driver for the Nuvoton NCT6694
- add new GPIO driver for MAX7360
Driver improvements:
- add support for Tegra 256 to the gpio-tegra186 driver
- add support for Loongson-2K0300 to the gpio-loongson-64bit driver
- refactor the gpio-aggregator module to expose its GPIO forwarder
API to other in-kernel users (to enable merging of a new pinctrl
driver that uses it)
- convert all remaining drivers to using the modernized generic GPIO
chip API and remove the old interface
- stop displaying global GPIO numbers in debugfs output of controller
drivers
- extend the gpio-regmap helper with a new config option and improve
its support for GPIO interrupts
- remove redundant fast_io parameter from regmap configs in GPIO
drivers that already use MMIO regmaps which imply it
- add support for a new model in gpio-mmio: ixp4xx expansion bus
- order includes alphabetically in a few drivers for better
readability
- use generic device properties where applicable
- use devm_mutex_init() where applicable
- extend build coverage of drivers by enabling more to be compiled
with COMPILE_TEST enabled
- allow building gpio-stmpe as a module
- use dev_err_probe() where it makes sense in drivers
Late driver fixes:
- fix setting GPIO direction to output in gpio-mpfs
Documentation:
- document the usage of software nodes with GPIO chips
Device-tree bindings:
- Add DT bindings documents for new hardware: Tegra256, MAX7360
- Document a new model in Loongson bindings: LS2K0300
- Document a new model using the generic GPIO binding: IXP4xx
- Convert the DT binding for fsl,mxs-pinctrl to YAML
- fix the schema ID in the "trivial" GPIO schema
- describe GPIO hogs in the generic GPIO binding"
* tag 'gpio-updates-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (122 commits)
gpio: mpfs: fix setting gpio direction to output
gpio: generic: move GPIO_GENERIC_ flags to the correct header
gpio: generic: rename BGPIOF_ flags to GPIO_GENERIC_
gpio: nomadik: fix the debugfs helper stub
MAINTAINERS: Add entry on MAX7360 driver
input: misc: Add support for MAX7360 rotary
input: keyboard: Add support for MAX7360 keypad
gpio: max7360: Add MAX7360 gpio support
gpio: regmap: Allow to provide init_valid_mask callback
gpio: regmap: Allow to allocate regmap-irq device
pwm: max7360: Add MAX7360 PWM support
pinctrl: Add MAX7360 pinctrl driver
mfd: Add max7360 support
dt-bindings: mfd: gpio: Add MAX7360
rtc: Add Nuvoton NCT6694 RTC support
hwmon: Add Nuvoton NCT6694 HWMON support
watchdog: Add Nuvoton NCT6694 WDT support
can: Add Nuvoton NCT6694 CANFD support
i2c: Add Nuvoton NCT6694 I2C support
gpio: Add Nuvoton NCT6694 GPIO support
...
Pull hwmon updates from Guenter Roeck:
"New drivers:
- KEBA fan controller
- KEBA battery monitoring controller
- MAX77705
Support added to existing drivers:
- MAXIMUS VI HERO and ROG MAXIMUS Z90 Formula support (asus-ec-sensors)
- SQ52206 support (ina238)
- lt3074 support (pmbus/lt3074)
- ADPM12160 support (pmbus/max34440)
- MPM82504 and for MPM3695 family support (pmbus/mpq8785)
- Add the Dell OptiPlex 7050 to the DMI whitelist (dell-smm)
- Zen5 Ryzen Desktop support (k10temp)
Various other minor fixes and improvements"
* tag 'hwmon-for-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (48 commits)
doc: hwmon: acpi_power_meter: Add information about enabling the power capping feature.
hwmon: (isl28022) Fix current reading calculation
hwmon: (lm75) Fix I3C transfer buffer pointer for incoming data
hwmon: Add KEBA fan controller support
hwmon: pmbus: mpq8785: Add support for MPM3695 family
hwmon: pmbus: mpq8785: Add support for MPM82504
hwmon: pmbus: mpq8785: Implement VOUT feedback resistor divider ratio configuration
hwmon: pmbus: mpq8785: Prepare driver for multiple device support
dt-bindings: hwmon: Add bindings for mpq8785 driver
hwmon: (ina238) Modify the calculation formula to adapt to different chips
hwmon: (ina238) Add support for SQ52206
dt-bindings: Add SQ52206 to ina2xx devicetree bindings
hwmon: (ina238) Add ina238_config to save configurations for different chips
hwmon: (ausus-ec-sensors) add MAXIMUS VI HERO.
hwmon: (isl28022, nct7363) Convert to use maple tree register cache
hwmon: (asus-ec-sensors) check sensor index in read_string()
hwmon: (asus-ec-sensors) add ROG MAXIMUS Z90 Formula.
dt-bindings: hwmon: Add Sophgo SG2044 external hardware monitor support
hwmon: (max77705) Add initial support
hwmon: (tmp102) add vcc regulator support
...
The KEBA fan controller is found in the system FPGA of KEBA PLC devices.
It detects if the fan is removed or blocked. For fans with tacho signal
the monitoring of the speed of the fan is supported. It also supports to
regulate the speed of fans with PWM input.
The auxiliary device for this driver is instantiated by the cp500 misc
driver.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://lore.kernel.org/r/20250425194823.54664-1-gerhard@engleder-embedded.com
[groeck: Added various missing "break;" statements]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The EC of OneXPlayer devices used to only control the fan. This is no
longer the case, with the EC of OneXPlayer gaining additional
functionality (turbo button, turbo led, battery controls).
As it will be beneficial from a complexity perspective to retain this
driver as a single unit, move it out of hwmon, and into platform/x86.
Also, remove the hwmon documentation to prepare moving it to
Documentation/ABI/.
While at it, add myself to the maintainer's file.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250425111821.88746-4-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The KEBA battery monitoring controller is found in the system FPGA of
KEBA PLC devices. It puts a load on the coin cell battery to check the
state of the battery. If the coin cell battery is nearly empty, then
the user space is signaled with a hwmon alarm.
The auxiliary device for this driver is instantiated by the cp500 misc
driver.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://lore.kernel.org/r/20250409190830.60489-1-gerhard@engleder-embedded.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Congatec Board Controller. This controller exposes
temperature, voltage, current and fan sensors.
The available sensors list cannot be predicted. Some sensors can be
present or not, depending the system.
The driver has an internal list of all possible sensors, for all Congatec
boards. The Board Controller gives to the driver its sensors list, and
their status (active or not).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20250203-congatec-board-controller-hwmon-v4-1-ff6c76a4662c@bootlin.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7363Y is a fan controller which provides up to 16
independent FAN input monitors. It can report each FAN input count
values. The NCT7363Y also provides up to 16 independent PWM
outputs. Each PWM can output specific PWM signal by manual mode to
control the FAN duty outside.
Signed-off-by: Ban Feng <kcfeng0@nuvoton.com>
Message-ID: <20241022052905.4062682-3-kcfeng0@nuvoton.com>
[groeck: Dropped unnecessary variable initialization, and , after { }]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"Obsolete driver removals:
- Removed obsolete adm1021 and max6642 drivers
New drivers:
- MPS MP2891, MP2993, MP9941, and MP5920
- SPD5118 (Temperature Sensor and EEPROM)
Added device support to existing drivers:
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
Notable enhancements and fixes:
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and
with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827
drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (103 commits)
hwmon: (max6697) Fix swapped temp{1,8} critical alarms
hwmon: (max6697) Fix underflow when writing limit attributes
hwmon: Remove obsolete adm1021 and max6642 drivers
hwmon: (pmbus/ltc4286) Drop unused i2c device ids
hwmon: (g762) Initialize fans after configuring clock
hwmon: (amc6821) Add support for pwm1_mode attribute
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Use BIT() and GENMASK()
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc6821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
hwmon: (lm95234) Fix underflows seen when writing limit attributes
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
...
ADM1021, MAX6642, and compatible chips are supported by the lm90 driver.
Remove the obsolete stand-alone drivers to reduce maintenance overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This addition adds in the ability for the system to scan
the EC chip in the Lenovo ThinkStation systems to get the
current fan RPM speeds the Maximum speed value for each
fan also provides the CPU, DIMM other thermal statuses
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20240328121250.331146-1-dober6023@gmail.com
[groeck: Dropped pointless case statements]
[Colin King: Fixed spelling error accesssible -> accessible]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver support two functions: PWM and Tachometer. The PWM feature can
handle up to 16 output ports, while the Tachometer can monitor to up to 16
input ports as well. This driver implements them by exposing two kernel
subsystems: PWM and HWMON. The PWM subsystem can be utilized alongside
existing drivers for controlling elements such as fans (pwm-fan.c),
beepers (pwm-beeper.c) and so on. Through the HWMON subsystem, the driver
provides sysfs interfaces for fan.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240221104025.1306227-4-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the ASUS ROG RYUJIN II 360
all-in-one CPU liquid cooler, which communicates through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] by
Florian Freudiger.
Available sensors are pump, internal and external
(controller) fan speed in RPM, their duties in PWM, as well as
coolant temperature.
Attaching external fans to the controller is optional and allows them
to be controlled from the device. If not connected, the fan-related
sensors will report zeroes. The controller is a separate hardware unit
that comes bundled with the AIO and connects to it to allow fan control.
The addressable LCD screen is not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/pull/653
Tested-by: Florian Freudiger <florian.freudiger@proton.me>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240108094453.22986-1-savicaleksa83@gmail.com
[groeck: Add HID dependency]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver enables hardware monitoring support for NZXT Kraken
X53/X63/X73 and Z53/Z63/Z73 all-in-one CPU liquid coolers.
All models expose liquid temperature and pump speed (in RPM), as well as
PWM control (natively only through a temp-PWM curve, but the driver also
emulates fixed PWM control on top of that). The Z-series models
additionally expose the speed and duty of an optionally connected fan,
with the same PWM control capabilities.
Pump and fan duty control mode can be set through pwm[1-2]_enable,
where 1 is for the manual control mode and 2 is for the liquid temp
to PWM curve mode. Writing a 0 disables control of the channel through
the driver after setting its duty to 100%. As it is not possible to query
the device for the active mode, the driver keeps track of it.
The temperature of the curves relates to the fixed [20-59] C range, per
device limitations, and correlating to the detected liquid temperature.
Only PWM values (ranging from 0-255) can be set.
The addressable RGB LEDs and LCD screen, included only on Z-series models,
are not supported in this driver.
Co-developed-by: Jonas Malaco <jonas@protocubo.io>
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Co-developed-by: Yury Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Yury Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240129111932.368232-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Amphenol ChipCap 2 is a capacitive polymer humidity and temperature
sensor with an integrated EEPROM and minimum/maximum humidity alarms.
All device variants offer an I2C interface and depending on the part
number, two different output modes:
- CC2D: digital output
- CC2A: analog (PDM) output
This driver adds support for the digital variant (CC2D part numbers),
which includes the following part numbers:
- non-sleep measurement mode (CC2D23, CC2D25, CC2D33, CC2D35)
- sleep measurement mode (CC2D23S, CC2D25S, CC2D33S, CC2D35S)
The Chipcap 2 EEPROM can be accessed to configure a series of parameters
like the minimum/maximum humidity alarm threshold and hysteresis. The
EEPROM is only accessible in the command window after a power-on reset.
The default window lasts 10 ms if no Start_CM command is sent. After the
command window is finished (either after the mentioned timeout of after
a Start_NOM command is sent), the device enters the normal operation
mode and makes a first measurement automatically.
Unfortunately, the device does not provide any hardware or software
reset and therefore the driver must trigger power cycles to enter the
command mode. A dedicated, external regulator is required for that.
This driver keeps the device off until a measurement or access to the
EEPROM is required, making use of the first automatic measurement to
avoid different code paths for sleep and non-sleep devices.
The minimum and maximum humidity alarms are configured with two
registers per alarm: one stores the alarm threshold and the other one
keeps the value that turns off the alarm. The alarm signals are only
updated when a measurement is carried out.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240130-topic-chipcap2-v6-5-260bea05cf9b@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC4282 hot swap controller allows a board to be safely inserted and
removed from a live backplane. Using one or more external N-channel pass
transistors, board supply voltage and inrush current are ramped up at an
adjustable rate. An I2C interface and onboard ADC allows for monitoring
of board current, voltage, power, energy and fault status.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240129-b4-ltc4282-support-v4-3-fe75798164cc@analog.com
[groeck: clamp value range in ltc4282_write_voltage_byte_cached()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Gigabyte AORUS Waterforce
all-in-one CPU liquid coolers, which communicate through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] and
confirmed by me on a Waterforce X240 by observing the sent reports from
the official software.
Available sensors are pump and fan speed in RPM, as well as coolant
temperature. Also available through debugfs is the firmware version.
Attaching a fan is optional and allows it to be controlled from the
device. If it's not connected, the fan-related sensors will report
zeroes.
The addressable RGB LEDs and LCD screen are not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/issues/167
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231207122402.107032-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC2991 Octal I2C Voltage, Current, and Temperature
Monitor.
The LTC2991 is used to monitor system temperatures, voltages and
currents. Through the I2C serial interface, the eight monitors can
individually measure supply voltages and can be paired for
differential measurements of current sense resistors or temperature
sensing transistors. Additional measurements include internal
temperature and internal VCC.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231026103413.27800-2-antoniu.miclaus@analog.com
[groeck: Fixed up documentation warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
POWER-Z is a series of devices to monitor power characteristics of
USB-C connections and display those on a on-device display.
Some of the devices, notably KM002C and KM003C, contain an additional
port which exposes the measurements via USB.
This is a driver for this monitor port.
It was developed and tested with the KM003C.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230902-powerz-v4-1-7ec2c1440687@weissschuh.net
[groeck:
Release urb after hwmon registration error;
Move priv->status initialization to correct place before reinit_completion
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add base support for Renesas HS3001 temperature
and humidity sensors and its compatibles HS3002,
HS3003 and HS3004.
The sensor has a fix I2C address 0x44. The resolution
is fixed to 14bit (ref. Missing feature).
Missing feature:
- Accessing non-volatile memory: Custom board has no
possibility to control voltage supply of sensor. Thus,
we cannot send the necessary control commands within
the first 10ms after power-on.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20230725042207.22310-2-andre.werner@systec-electronic.com
[groeck: Cosmetic documentation fixup; added documentation to index;
replaced probe_new with probe dropped unused variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMM665 and related chips are power controller/sequencer chips from
Summit Microelectronics. The company was acquired by Qualcomm in 2012,
and support for the chip series stopped.
The chips are long since gone from active use, making the driver
unsupportable and just consuming space and compile time. Remove it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hewlett-Packard (and some HP Compaq) business-class computers report
hardware monitoring information via WMI. This driver exposes that
information to hwmon.
Initial support is provided for temperature, fan speed, and intrusion
sensor types. Provisional support is provided for voltage and current
sensor types.
HP's WMI implementation permits many other types of numeric sensors.
Therefore, a debugfs interface is also provided to enumerate and
inspect all numeric sensors visible on the WMI side. This should
facilitate adding support for other sensor types in the future.
Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300
SFF.
Note that provisionally supported sensor types are untested and seem
to be rare-to-nonexistent in the wild, having been encountered
neither on test systems nor in ACPI dumps from the Linux Hardware
Database. They are included because their popularity in general makes
their presence on past or future HP systems plausible and because no
doubt exists as to how the sensors themselves would be represented in
WMI (alarm attributes will need to wait for hardware to be located).
A 2005 HP whitepaper gives the relevant sensor object MOF definition
and sensor value scaling calculation, and both this driver and the
official HP Performance Advisor utility comply with them (confirmed
in the latter case by reverse engineering).
Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech
[groeck: Set error return value for intrusion writes to -EINVAL.
Always accept writes of 0 even if there was no intrusion. ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31827 is a low-power temperature switch with I2C interface.
The device is a ±1°C accuracy from -40°C to +125°C
(12 bits) local temperature switch and sensor with I2C/SM-
Bus interface. The combination of small 6-bump wafer-lev-
el package (WLP) and high accuracy makes this temper-
ature sensor/switch ideal for a wide range of applications.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230524160131.14081-2-daniel.matyas@analog.com
[groeck: Improved define alignment, return -EINVAL after bad user input,
fixed up compatible statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon TDA38640 Voltage Regulator
- NXP MC34VR500 PMIC
- GXP fan controller
- MPQ7932 Power Management IC
New chip or board support added to existing drivers:
- it87: IT87952E; also other cleanup/improvements
- intel-m10-bmc-hwmon: N6000
- pmbus/max16601: MAX16600
- aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer
Poweradjust 3, Aquacomputer Aquaero
- nct6775: Support for B650/B660/X670 ASUS boards
- oxp-sensors: AYANEO AIR and AIR Pro
Other notable changes:
- Various kernel documentation fixes
- Various devicetree bindings fixes
- Explicitly deprecated [devm_]hwmon_device_register_with_groups
- ftsteutates: Support for fanX_fault and other cleanup
- ltc2945: Support for setting shunt resistor and other cleanup/fixes
- coretemp: Avoid RDMSR interrupts to isolated CPUs, and simplify
platform device handling
... and various other minor cleanups and fixes"
* tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (66 commits)
hwmon: Deprecate [devm_]hwmon_device_register_with_groups
hwmon: (mlxreg-fan) Return zero speed for broken fan
hwmon: (gxp-fan-ctrl) use devm_platform_get_and_ioremap_resource()
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Aquastream Ultimate
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Poweradjust 3
hwmon: (iio_hwmon) use dev_err_probe
hwmon: intel-m10-bmc-hwmon: Add N6000 sensors
Docs/hwmon/index: Add missing SPDX License Identifier
hwmon: (it87) Updated documentation for recent updates to it87
hwmon: (it87) Add new chipset IT87952E
hwmon: (it87) Allow multiple chip IDs for force_id
hwmon: (it87) Add chip_id in some info message
hwmon: (it87) List full chip model name
hwmon: (it87) Disable configuration exit for certain chips
hwmon: (it87) Allow disabling exiting of configuration mode
Documentation: hwmon: correct spelling
hwmon: (pmbus/max16601) Add support for MAX16600
hwmon: (ltc2945) Allow setting shunt resistor
hwmon: (ltc2945) Handle error case in ltc2945_value_store
hwmon: (ltc2945) Add devicetree match table
...
The GXP SoC can support up to 16 fans through the interface provided by
the CPLD. The current support is limited to 8 fans. The fans speeds are
controlled via 8 different PWMs which can vary in value from 0-255. The
fans are also capable of reporting if they have failed to the CPLD which
in turn reports the status to the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20230103203654.59322-2-nick.hawkins@hpe.com
[groeck: Improved alignment of defined, added missing include linux/bits.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The s3c adc driver was removed along with the s3c24xx platform, so the
hwmon driver is orphaned and can be removed.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading
and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and
they can be told appart only by the boot cpu vendor (Intel/AMD).
Currently only AMD boards are supported since Intel have different EC
registers and values to read/write.
Fan control is provided via pwm interface in the range [0-255]. AMD
boards have [0-100] as range in the EC, the written value is scaled to
accommodate for that.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com
[groeck: Removed misleading comment about module_platform_driver()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides an i2c I/O mechanism for the core nct6775 driver,
as might be used by a BMC. Because the Super I/O chip is shared with
the host CPU in such a scenario (and the host should ultimately be in
control of it), the i2c driver is strictly read-only to avoid
interfering with any usage by the host (aside from the bank-select
register, which seems to be replicated for the i2c interface).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220428012707.24921-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
