Merge tag 'qcom-dts-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm Device Tree Changes for v5.5

* Add thermal zones and IRQ support for MSM8974
* Add 5vs2 regulator node for PM8941
* Add reboot-mode node, fix sdhci and card detect on MSM8974-FP2
* Add IPQ4019 SDHCI node

* tag 'qcom-dts-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  ARM: dts: msm8974: thermal: Add thermal zones for each sensor
  ARM: dts: msm8974: thermal: Add interrupt support
  ARM: dts: qcom: pm8941: add 5vs2 regulator node
  ARM: dts: msm8974-FP2: add reboot-mode node
  ARM: dts: msm8974-FP2: Increase load on l20 for sdhci
  ARM: dts: msm8974-FP2: Drop unused card-detect pin
  ARM: dts: qcom: ipq4019: Add SDHCI controller node

Link: https://lore.kernel.org/r/1573068840-13098-5-git-send-email-agross@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/qcom-ipq4019.dtsi

@@ -206,6 +206,18 @@ tlmm: pinctrl@1000000 {
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		sdhci: sdhci@7824900 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x7824900 0x11c>, <0x7824000 0x800>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			bus-width = <8>;
+			clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_DCD_XO_CLK>;
+			clock-names = "core", "iface", "xo";
+			status = "disabled";
+		};
+
 		blsp_dma: dma@7884000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x07884000 0x23000>;

arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts

@@ -221,6 +221,8 @@ l20 {
 						regulator-max-microvolt = <2950000>;
 
 						regulator-boot-on;
+						regulator-system-load = <200000>;
+						regulator-allow-set-load;
 					};
 
 					l21 {
@@ -272,14 +274,6 @@ cmd-data {
 			};
 		};
 
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		};
-
 		sdhc2_pin_a: sdhc2-pin-active {
 			clk {
 				pins = "sdc2_clk";
@@ -317,7 +311,7 @@ sdhci@f98a4900 {
 		bus-width = <4>;
 
 		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
+		pinctrl-0 = <&sdhc2_pin_a>;
 	};
 
 	usb@f9a55000 {
@@ -344,6 +338,16 @@ phy@a {
 			};
 		};
 	};
+
+	imem@fe805000 {
+		status = "okay";
+
+		reboot-mode {
+			mode-normal	= <0x77665501>;
+			mode-bootloader	= <0x77665500>;
+			mode-recovery	= <0x77665502>;
+		};
+	};
 };
 
 &spmi_bus {

arch/arm/boot/dts/qcom-msm8974.dtsi

@@ -217,6 +217,96 @@ cpu_crit3: trip1 {
 				};
 			};
 		};
+
+		q6-dsp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				q6_dsp_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		modemtx-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				modemtx_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		video-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				video_alert0: trip-point0 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		wlan-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				wlan_alert0: trip-point0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		gpu-thermal-top {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				gpu1_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		gpu-thermal-bottom {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				gpu2_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
 	};
 
 	cpu-pmu {
@@ -441,6 +531,8 @@ tsens: thermal-sensor@fc4a9000 {
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 			nvmem-cell-names = "calib", "calib_backup";
 			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
 			#thermal-sensor-cells = <1>;
 		};
 
@@ -1217,6 +1309,17 @@ dsi_phy0: dsi-phy@fd922a00 {
 				clock-names = "iface";
 			};
 		};
+
+		imem@fe805000 {
+			status = "disabled";
+			compatible = "syscon", "simple-mfd";
+			reg = <0xfe805000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+			};
+		};
 	};
 
 	smd {

arch/arm/boot/dts/qcom-pm8941.dtsi

@@ -178,6 +178,16 @@ pm8941_5vs1: 5vs1 {
 				qcom,vs-soft-start-strength = <0>;
 				regulator-initial-mode = <1>;
 			};
+
+			pm8941_5vs2: 5vs2 {
+				regulator-enable-ramp-delay = <1000>;
+				regulator-pull-down;
+				regulator-over-current-protection;
+				qcom,ocp-max-retries = <10>;
+				qcom,ocp-retry-delay = <30>;
+				qcom,vs-soft-start-strength = <0>;
+				regulator-initial-mode = <1>;
+			};
 		};
 	};
 };