Luciano Coelho 69aa167583 wlcore: ignore dummy packet events in PLT mode ...

Sometimes the firmware sends a dummy packet event while we are in PLT
mode.  This doesn't make sense, it's a firmware bug.  Fix this by
ignoring dummy packet events when we're PLT mode.

Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

2014-04-14 14:31:41 -04:00

..

acx.c

wlcore: enable beacon filtering only after receiving a beacon

2014-02-13 15:20:16 -05:00

acx.h

wl18xx: move to new firmware (wl18xx-fw-3.bin)

2014-02-13 15:20:15 -05:00

boot.c

wlcore: use single-role version when verifying the PLT firmware

2013-02-08 10:05:01 +02:00

boot.h

wlcore: create private static_data area and add operation to parse it

2012-06-05 15:58:20 +03:00

cmd.c

wlcore: decrease warning verbosity during recovery

2014-02-13 15:20:16 -05:00

cmd.h

wlcore: increase timeout to 5000 msecs

2014-02-13 15:20:16 -05:00

conf.h

wlcore: fwlog dynamic mem_block control

2013-10-23 09:47:40 +03:00

debug.h

wlcore: use print_hex_dump_debug()

2013-03-25 12:36:24 +02:00

debugfs.c

wlcore: print active channel in the driver_state

2013-10-23 09:47:39 +03:00

debugfs.h

wlcore: add debugfs macro to help print fw statistics arrays

2012-06-05 15:58:08 +03:00

event.c

wlcore: ignore dummy packet events in PLT mode

2014-04-14 14:31:41 -04:00

event.h

wlcore: support scan reports during periodic scan

2012-12-11 12:37:23 +02:00

hw_ops.h

wlcore/wl12xx/wl18xx: simplify fw_status handling

2014-02-13 15:20:15 -05:00

ini.h

wlcore/wl12xx: add support for HP and SKW FEM radio manufacturers

2012-06-13 21:52:56 +03:00

init.c

wlcore: enable beacon filtering only after receiving a beacon

2014-02-13 15:20:16 -05:00

init.h

wl12xx/wlcore: move wl1271 struct to wlcore and add ops

2012-04-12 08:43:56 +03:00

io.c

wlcore: Prevent processing of work items during op_stop

2012-07-10 12:10:14 -04:00

io.h

wlcore: block read/writes to FW during ELP

2014-02-13 15:20:14 -05:00

Kconfig

Remove GENERIC_HARDIRQ config option

2013-09-13 15:09:52 +02:00

main.c

net: Replace min macro with min_t

2014-03-03 15:35:54 -05:00

Makefile

wlcore: move sysfs handling to a separate file

2013-06-17 11:56:59 +03:00

ps.c

wlcore: AP: don't start mac80211 PS on non-peer HLIDs

2014-02-13 15:20:14 -05:00

ps.h

wl12xx/wlcore: move wl1271 struct to wlcore and add ops

2012-04-12 08:43:56 +03:00

rx.c

wlcore/wl12xx/wl18xx: configure num_links per-hw

2014-02-13 15:20:15 -05:00

rx.h

wlcore/wl12xx/wl18xx: simplify fw_status handling

2014-02-13 15:20:15 -05:00

scan.c

cfg80211: consolidate passive-scan and no-ibss flags

2013-11-25 20:49:35 +01:00

scan.h

wlcore: support scan reports during periodic scan

2012-12-11 12:37:23 +02:00

sdio.c

wlcore: remove newly introduced alloc/OOM messages

2013-02-11 15:34:58 -05:00

spi.c

net: Replace min macro with min_t

2014-03-03 15:35:54 -05:00

sysfs.c

net: Replace min macro with min_t

2014-03-03 15:35:54 -05:00

sysfs.h

wlcore: move sysfs handling to a separate file

2013-06-17 11:56:59 +03:00

testmode.c

wlcore: fix interrogate command length

2013-10-23 09:47:40 +03:00

testmode.h

mac80211: add vif to testmode cmd

2013-08-12 14:11:42 +02:00

tx.c

wlcore: consider multiple APs when checking active_link_count

2014-02-13 15:20:16 -05:00

tx.h

wlcore: send EAPOL frames with voice priority

2014-02-13 15:20:15 -05:00

wl12xx_80211.h

…

wlcore_i.h

wl18xx: move to new firmware (wl18xx-fw-3.bin)

2014-02-13 15:20:15 -05:00

wlcore.h

wlcore: wl18xx: allow CCK rates for AP mode

2014-02-13 15:20:16 -05:00