Merge series from Jerome Brunet <jbrunet@baylibre.com>:
This patchset fixes 2 problems on TDM which both find a solution
by properly implementing the .trigger() callback for the TDM backend.
ATM, enabling the TDM formatters is done by the .prepare() callback
because handling the formatter is slow due to necessary calls to CCF.
The first problem affects the TDMIN. Because .prepare() is called on DPCM
backend first, the formatter are started before the FIFOs and this may
cause a random channel shifts if the TDMIN use multiple lanes with more
than 2 slots per lanes. Using trigger() allows to set the FE/BE order,
solving the problem.
There has already been an attempt to fix this 3y ago [1] and reverted [2]
It triggered a 'sleep in irq' error on the period IRQ. The solution is
to just use the bottom half of threaded IRQ. This is patch #1. Patch #2
and #3 remain mostly the same as 3y ago.
For TDMOUT, the problem is on pause. ATM pause only stops the FIFO and
the TDMOUT just starves. When it does, it will actually repeat the last
sample continuously. Depending on the platform, if there is no high-pass
filter on the analog path, this may translate to a constant position of
the speaker membrane. There is no audible glitch but it may damage the
speaker coil.
Properly stopping the TDMOUT in pause solves the problem. There is
behaviour change associated with that fix. Clocks used to be continuous
on pause because of the problem above. They will now be gated on pause by
default, as they should. The last change introduce the proper support for
continuous clocks, if needed.
[1]: https://lore.kernel.org/linux-amlogic/20211020114217.133153-1-jbrunet@baylibre.com
[2]: https://lore.kernel.org/linux-amlogic/20220421155725.2589089-1-narmstrong@baylibre.com
Amlogic sound cards do create a lot of pcm interfaces, possibly more than
8. Some pcm interfaces are internal (like DPCM backends and c2c) and not
exposed to userspace.
Those interfaces still increase the number passed to snd_find_free_minor(),
which eventually exceeds 8 causing -EBUSY error on card registration if
CONFIG_SND_DYNAMIC_MINORS=n and the interface is exposed to userspace.
select CONFIG_SND_DYNAMIC_MINORS for Amlogic cards to avoid the problem.
Fixes: 7864a79f37 ("ASoC: meson: add axg sound card support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426134150.3053741-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
So far, the formatters have been reset/enabled using the .prepare()
callback. This was done in this callback because walking the formatters use
a mutex. A mutex is used because formatter handling require dealing
possibly slow clock operation.
With the support of non-atomic, .trigger() callback may be used which also
allows to properly enable and disable formatters on start but also
pause/resume.
This solve a random shift on TDMIN as well repeated samples on for TDMOUT.
Fixes: d60e4f1e4b ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-4-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Non atomic operations need to be performed in the trigger callback
of the TDM interfaces. Those are BEs but what matters is the nonatomic
flag of the FE in the DPCM context. Just set nonatomic for everything so,
at least, what is done is clear.
Fixes: 7864a79f37 ("ASoC: meson: add axg sound card support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the AXG audio subsystem, there is a possible random channel shift on
TDM capture, when the slot number per lane is more than 2, and there is
more than one lane used.
The problem has been there since the introduction of the axg audio support
but such scenario is pretty uncommon. This is why there is no loud
complains about the problem.
Solving the problem require to make the links non-atomic and use the
trigger() callback to start FEs and BEs in the appropriate order.
This was tried in the past and reverted because it caused the block irq to
sleep while atomic. However, instead of reverting, the solution is to call
snd_pcm_period_elapsed() in a non atomic context.
Use the bottom half of a threaded IRQ to do so.
Fixes: 6dc4fa179f ("ASoC: meson: add axg fifo base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checkers complain that the silicon_uid variable passed by
pointer to cs35l56_read_silicon_uid() could later be used
uninitialised when calling cs_amp_get_efi_calibration_data().
cs35l56_read_silicon_uid() must have succeeded to call
cs_amp_get_efi_calibration_data() and that would have populated the
variable.
However, initialise the value so we are not haunted by it forevermore.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Fixes: e1830f66f6 ("ASoC: cs35l56: Add helper functions for amp calibration")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240422103211.236063-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using davinci-mcasp as CPU DAI with simple-card, there are some
conditions that cause simple-card to finish registering a sound card before
davinci-mcasp finishes registering all sound components. This creates a
non-working sound card from userspace with no problem indication apart
from not being able to play/record audio on a PCM stream. The issue
arises during simultaneous probe execution of both drivers. Specifically,
the simple-card driver, awaiting a CPU DAI, proceeds as soon as
davinci-mcasp registers its DAI. However, this process can lead to the
client mutex lock (client_mutex in soc-core.c) being held or davinci-mcasp
being preempted before PCM DMA registration on davinci-mcasp finishes.
This situation occurs when the probes of both drivers run concurrently.
Below is the code path for this condition. To solve the issue, defer
davinci-mcasp CPU DAI registration to the last step in the audio part of
it. This way, simple-card CPU DAI parsing will be deferred until all
audio components are registered.
Fail Code Path:
simple-card.c: probe starts
simple-card.c: simple_dai_link_of: simple_parse_node(..,cpu,..) returns EPROBE_DEFER, no CPU DAI yet
davinci-mcasp.c: probe starts
davinci-mcasp.c: devm_snd_soc_register_component() register CPU DAI
simple-card.c: probes again, finish CPU DAI parsing and call devm_snd_soc_register_card()
simple-card.c: finish probe
davinci-mcasp.c: *dma_pcm_platform_register() register PCM DMA
davinci-mcasp.c: probe finish
Cc: stable@vger.kernel.org
Fixes: 9fbd58cf4a ("ASoC: davinci-mcasp: Choose PCM driver based on configured DMA controller")
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240417184138.1104774-1-jpaulo.silvagoncalves@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating controls attached to widgets, there are a lot of rules if
they get their name prefixed with widget name or not. Due to that
controls ended up with weirdly looking names like "ssp0_fe DSP Volume",
while topology set it to "DSP Volume".
Fix this by setting no_wname_in_kcontrol_name to true in avs topology
widgets which disables unwanted behaviour.
Fixes: be2b81b519 ("ASoC: Intel: avs: Parse control tuples")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240418142621.2487478-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, all ASoC systems are set to use VPMON for DSP1RX5_SRC,
however, this is required only for internal boost systems.
External boost systems require VBSTMON instead of VPMON to be the
input to DSP1RX5_SRC.
Shared Boost Active acts like Internal boost (requires VPMON).
Shared Boost Passive acts like External boost (requires VBSTMON)
All systems require DSP1RX6_SRC to be set to VBSTMON.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://msgid.link/r/20240411142648.650921-1-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
This chain fixes some problems with some previous patches for handling
the ASP1 config registers. The root of the problem is that the ownership
of these registers can be either with the firmware or the driver, and that
the chip has to be soft-reset after downloading the firmware.
This chain adds and uses a regmap_read_bypassed() function so that the
driver can leave the regmap in cache-only until the chip has rebooted,
but still poll a register to detect when the chip has rebooted.
Richard Fitzgerald (4):
regmap: Add regmap_read_bypassed()
ALSA: hda: cs35l56: Exit cache-only after
cs35l56_wait_for_firmware_boot()
ASoC: cs35l56: Fix unintended bus access while resetting amp
ASoC: cs35l56: Prevent overwriting firmware ASP config
drivers/base/regmap/regmap.c | 37 ++++++++++++++
include/linux/regmap.h | 8 +++
include/sound/cs35l56.h | 2 +
sound/pci/hda/cs35l56_hda.c | 4 ++
sound/soc/codecs/cs35l56-sdw.c | 2 -
sound/soc/codecs/cs35l56-shared.c | 83 ++++++++++++++++++++-----------
sound/soc/codecs/cs35l56.c | 26 +++++++++-
7 files changed, 130 insertions(+), 32 deletions(-)
--
2.39.2
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The current code will reset the ChainDMA on release unconditionally which
can result the following error when the CHainDMA is not allocated:
ipc tx : 0xe040000|0x0: GLB_CHAIN_DMA
ipc tx reply: 0x2e000007|0x0: GLB_CHAIN_DMA
FW reported error: 7 - Unsupported operation requested
ipc error for msg 0xe040000|0x0
sof_pcm_stream_free: pcm_ops hw_free failed -22
Background:
Pulseaudio and Pipewire on startup opens all available streams and
closes them without triggering a start (after probing it's capabilities).
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
We somehow missed the default path for DSP libraries for LNL, and need
to restrict support for D0i3 w/ IPC4. Also add debugfs support for
firmware profile information so that sof-test scripts can show what is
being tested.
The codec leaves tie combo jack's sleeve/ring2 to floating status
default. It would cause electric noise while connecting the active
speaker jack during boot or shutdown.
This patch requests a gpio to control the additional jack circuit
to tie the contacts to the ground or floating.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://msgid.link/r/20240408091057.14165-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ChainDMA operation differs from normal pipelines that it is only
created when the stream started, in fact a PCM using ChainDMA has no
pipelines, modules.
To reset a ChainDMA, it needs to be first allocated in firmware. When
PulseAudio/PipeWire starts, they will probe the PCMs by opening them, check
hw_params and then close the PCM without starting audio.
Unconditionally resetting the ChainDMA can result the following error:
ipc tx : 0xe040000|0x0: GLB_CHAIN_DMA
ipc tx reply: 0x2e000007|0x0: GLB_CHAIN_DMA
FW reported error: 7 - Unsupported operation requested
ipc error for msg 0xe040000|0x0
sof_pcm_stream_free: pcm_ops hw_free failed -22
Add a new chain_dma_allocated flag to sof_ipc4_pcm_stream_priv to store the
ChainDMA allocation state and use this flag to skip sending the reset if
the ChainDMA is not allocated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240409110036.9411-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Only populate the ASP1 config registers in the regmap cache if the
ASP DAI is used. This prevents regcache_sync() from overwriting
these registers with their defaults when the firmware owns
control of these registers.
On a SoundWire system the ASP could be owned by the firmware to
share reference audio with the firmware on other cs35l56. Or it
can be used as a normal codec-codec interface owned by the driver.
The driver must not overwrite the registers if the firmware has
control of them.
The original implementation for this in commit 07f7d6e7a1
("ASoC: cs35l56: Fix for initializing ASP1 mixer registers") was
to still provide defaults for these registers, assuming that if
they were never reconfigured from defaults then regcache_sync()
would not write them out because they are not dirty. Unfortunately
regcache_sync() is not that smart. If the chip has not reset (so
the driver has not called regcache_mark_dirty()) a regcache_sync()
could write out registers that are not dirty.
To avoid accidental overwriting of the ASP registers, they are
removed from the table of defaults and instead are populated with
defaults only if one of the ASP DAI configuration functions is
called. So if the DAI has never been configured, the firmware is
assumed to have ownership of these registers, and the regmap cache
will not contain any entries for them.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 07f7d6e7a1 ("ASoC: cs35l56: Fix for initializing ASP1 mixer registers")
Link: https://msgid.link/r/20240408101803.43183-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new regmap_read_bypassed() so that the regmap can be left
in cache-only mode while it is booting, but the driver can still
read boot-status and chip-id information during this time.
This fixes race conditions where some writes could be issued to the
silicon while it is still rebooting, before the driver has determined
that the boot is complete.
This is typically prevented by putting regmap into cache-only until the
hardware is ready. But this assumes that the driver does not need to
access device registers to determine when it is "ready". For cs35l56
this involves polling a register and the original implementation relied
on having special handlers to block racing callbacks until dsp_work()
is complete. However, some cases were missed, most notably the ASP DAI
functions.
The regmap_read_bypassed() function allows the fix for this to be
simplified to putting regmap into cache-only during the reset. The
initial boot stages (poll HALO_STATE and read the chip ID) are all done
bypassed. Only when the amp is seen to be booted is the cache-only
revoked.
Changes are:
- cs35l56_system_reset() now leaves the regmap in cache-only status.
- cs35l56_wait_for_firmware_boot() polls using regmap_read_bypassed().
- cs35l56_init() revokes cache-only either via cs35l56_hw_init() or
when firmware has rebooted after a soft reset.
- cs35l56_hw_init() exits cache-only after it has determined that the
amp has booted.
- cs35l56_sdw_init() doesn't disable cache-only, since this must be
deferred to cs35l56_init().
- cs35l56_runtime_resume_common() waits for firmware boot before exiting
cache-only.
These changes cover three situations where the registers are not
accessible:
1) SoundWire first-time enumeration. The regmap is kept in cache-only
until the chip is fully booted. The original code had to exit
cache-only to read chip status in cs35l56_init() and cs35l56_hw_init()
but this is now deferred to after the firmware has rebooted.
In this case cs35l56_sdw_probe() leaves regmap in cache-only
(unchanged behaviour) and cs35l56_hw_init() exits cache-only after the
firmware is booted and the chip identified.
2) Soft reset during first-time initialization. cs35l56_init() calls
cs35l56_system_reset(), which puts regmap into cache-only.
On I2C/SPI cs35l56_init() then flows through to call
cs35l56_wait_for_firmware_boot() and exit cache-only. On SoundWire
the re-enumeration will enter cs35l56_init() again, which then drops
down to call cs35l56_wait_for_firmware_boot() and exit cache-only.
3) Soft reset after firmware download. dsp_work() calls
cs35l56_system_reset(), which puts regmap into cache-only. After this
the flow is the same as (2).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 8a731fd37f ("ASoC: cs35l56: Move utility functions to shared file")
Link: https://msgid.link/r/20240408101803.43183-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Asus T100TA quirk has been using an exact match on a product-name of
"T100TA" but there are also T100TAM variants with a slightly higher
clocked CPU and a metal backside which need the same quirk.
Sort the existing T100TA (stereo speakers) below the more specific
T100TAF (mono speaker) quirk and switch from exact matching to
substring matching so that the T100TA quirk will also match on
the T100TAM models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20240407191559.21596-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Fixes for v6.9
A relatively large set of fixes here, the biggest piece of it is a
series correcting some problems with the delay reporting for Intel SOF
cards but there's a bunch of other things. Everything here is driver
specific except for a fix in the core for an issue with sign extension
handling volume controls.
Before ACP firmware loading, DSP interrupts are not expected.
Sometimes after reboot, it's observed that before ACP firmware is loaded
false DSP interrupt is reported.
Registering the interrupt handler before acp initialization causing false
interrupts sometimes on reboot as ACP reset is not applied.
Correct the sequence by invoking acp initialization sequence prior to
registering interrupt handler.
Fixes: 738a2b5e2c ("ASoC: SOF: amd: Add IPC support for ACP IP block")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://msgid.link/r/20240404041717.430545-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Zhang Yi <zhangyi@everest-semi.com>:
We solved some issues related to headphone detection.And for using
the same configuration in different power conditions,we modified the
clock table
We got an error report about headphone type detection and button detection.
We fixed the headphone type detection error by adjusting the debounce timer
configuration. And we fixed the button detection error by disabling the
button detection feature when the headphone are unplugged and enabling it
when headphone are plugged in.
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://msgid.link/r/20240402062043.20608-2-zhangyi@everest-semi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Fix a set of problematic locking sequences and update error messages,
tested on SOF/SoundWire platforms.
In snd_soc_info_volsw(), mask is generated by figuring out the index of
the most significant bit set in max and converting the index to a
bitmask through bit shift 1. Unintended wraparound occurs when max is an
integer value with msb bit set. Since the bit shift value 1 is treated
as an integer type, the left shift operation will wraparound and set
mask to 0 instead of all 1's. In order to fix this, we type cast 1 as
`1ULL` to prevent the wraparound.
Fixes: 7077148fb5 ("ASoC: core: Split ops out of soc-core.c")
Signed-off-by: Stephen Lee <slee08177@gmail.com>
Link: https://msgid.link/r/20240326010131.6211-1-slee08177@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The drivers for Realtek SoundWire codecs use similar logs, which is
problematic to analyze problems reported by CI tools, e.g. "Failed to
get private value: 752001 => 0000 ret=-5". It's not uncommon to have
several Realtek devices on the same platform, having the same log
thrown makes support difficult.
This patch adds __func__ to all error logs which didn't already
include it.
No functionality change, only error logs are modified.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://msgid.link/r/20240325221817.206465-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
