While running this selftest which usually passes:
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
if I start PTP timestamping then run it again (debug prints added by me),
the unknown IPv6 MC traffic is seen by the CPU port even when it should
have been dropped:
~/selftests/drivers/net/dsa# ptp4l -i swp0 -2 -P -m
ptp4l[225.410]: selected /dev/ptp1 as PTP clock
[ 225.445746] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_add: port 0 adding L2 PTP trap
[ 225.453815] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP event trap
[ 225.462703] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_add: port 0 adding IPv4 PTP general trap
[ 225.471768] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP event trap
[ 225.480651] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_add: port 0 adding IPv6 PTP general trap
ptp4l[225.488]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[225.488]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
^C
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [FAIL]
reception succeeded, but should have failed
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
The PGID_MCIPV6 is configured correctly to not flood to the CPU,
I checked that.
Furthermore, when I disable back PTP RX timestamping (ptp4l doesn't do
that when it exists), packets are RX filtered again as they should be:
~/selftests/drivers/net/dsa# hwstamp_ctl -i swp0 -r 0
[ 218.202854] mscc_felix 0000:00:00.5: ocelot_l2_ptp_trap_del: port 0 removing L2 PTP trap
[ 218.212656] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP event trap
[ 218.222975] mscc_felix 0000:00:00.5: ocelot_ipv4_ptp_trap_del: port 0 removing IPv4 PTP general trap
[ 218.233133] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP event trap
[ 218.242251] mscc_felix 0000:00:00.5: ocelot_ipv6_ptp_trap_del: port 0 removing IPv6 PTP general trap
current settings:
tx_type 1
rx_filter 12
new settings:
tx_type 1
rx_filter 0
~/selftests/drivers/net/dsa# ./local_termination.sh eno0 swp0
TEST: swp0: Unicast IPv4 to primary MAC address [ OK ]
TEST: swp0: Unicast IPv4 to macvlan MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, promisc [ OK ]
TEST: swp0: Unicast IPv4 to unknown MAC address, allmulti [ OK ]
TEST: swp0: Multicast IPv4 to joined group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv4 to unknown group, allmulti [ OK ]
TEST: swp0: Multicast IPv6 to joined group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, promisc [ OK ]
TEST: swp0: Multicast IPv6 to unknown group, allmulti [ OK ]
So it's clear that something in the PTP RX trapping logic went wrong.
Looking a bit at the code, I can see that there are 4 typos, which
populate "ipv4" VCAP IS2 key filter fields for IPv6 keys.
VCAP IS2 keys of type OCELOT_VCAP_KEY_IPV4 and OCELOT_VCAP_KEY_IPV6 are
handled by is2_entry_set(). OCELOT_VCAP_KEY_IPV4 looks at
&filter->key.ipv4, and OCELOT_VCAP_KEY_IPV6 at &filter->key.ipv6.
Simply put, when we populate the wrong key field, &filter->key.ipv6
fields "proto.mask" and "proto.value" remain all zeroes (or "don't care").
So is2_entry_set() will enter the "else" of this "if" condition:
if (msk == 0xff && (val == IPPROTO_TCP || val == IPPROTO_UDP))
and proceed to ignore the "proto" field. The resulting rule will match
on all IPv6 traffic, trapping it to the CPU.
This is the reason why the local_termination.sh selftest sees it,
because control traps are stronger than the PGID_MCIPV6 used for
flooding (from the forwarding data path).
But the problem is in fact much deeper. We trap all IPv6 traffic to the
CPU, but if we're bridged, we set skb->offload_fwd_mark = 1, so software
forwarding will not take place and IPv6 traffic will never reach its
destination.
The fix is simple - correct the typos.
I was intentionally inaccurate in the commit message about the breakage
occurring when any PTP timestamping is enabled. In fact it only happens
when L4 timestamping is requested (HWTSTAMP_FILTER_PTP_V2_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT). But ptp4l requests a larger RX
timestamping filter than it needs for "-2": HWTSTAMP_FILTER_PTP_V2_EVENT.
I wanted people skimming through git logs to not think that the bug
doesn't affect them because they only use ptp4l in L2 mode.
Fixes: 96ca08c058 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230207183117.1745754-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Saeed Mahameed says:
====================
mlx5 fixes 2023-02-07
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Serialize module cleanup with reload and remove
net/mlx5: fw_tracer, Zero consumer index when reloading the tracer
net/mlx5: fw_tracer, Clear load bit when freeing string DBs buffers
net/mlx5: Expose SF firmware pages counter
net/mlx5: Store page counters in a single array
net/mlx5e: IPoIB, Show unknown speed instead of error
net/mlx5e: Fix crash unsetting rx-vlan-filter in switchdev mode
net/mlx5: Bridge, fix ageing of peer FDB entries
net/mlx5: DR, Fix potential race in dr_rule_create_rule_nic
net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change
====================
Link: https://lore.kernel.org/r/20230208030302.95378-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arınç reports that on his MT7621AT Unielec U7621-06 board and MT7623NI
Bananapi BPI-R2, packets received by the CPU over mt7530 switch port 0
(of which this driver acts as the DSA master) are not processed
correctly by software. More precisely, they arrive without a DSA tag
(in packet or in the hwaccel area - skb_metadata_dst()), so DSA cannot
demux them towards the switch's interface for port 0. Traffic from other
ports receives a skb_metadata_dst() with the correct port and is demuxed
properly.
Looking at mtk_poll_rx(), it becomes apparent that this driver uses the
skb vlan hwaccel area:
union {
u32 vlan_all;
struct {
__be16 vlan_proto;
__u16 vlan_tci;
};
};
as a temporary storage for the VLAN hwaccel tag, or the DSA hwaccel tag.
If this is a DSA master it's a DSA hwaccel tag, and finally clears up
the skb VLAN hwaccel header.
I'm guessing that the problem is the (mis)use of API.
skb_vlan_tag_present() looks like this:
#define skb_vlan_tag_present(__skb) (!!(__skb)->vlan_all)
So if both vlan_proto and vlan_tci are zeroes, skb_vlan_tag_present()
returns precisely false. I don't know for sure what is the format of the
DSA hwaccel tag, but I surely know that lowermost 3 bits of vlan_proto
are 0 when receiving from port 0:
unsigned int port = vlan_proto & GENMASK(2, 0);
If the RX descriptor has no other bits set to non-zero values in
RX_DMA_VTAG, then the call to __vlan_hwaccel_put_tag() will not, in
fact, make the subsequent skb_vlan_tag_present() return true, because
it's implemented like this:
static inline void __vlan_hwaccel_put_tag(struct sk_buff *skb,
__be16 vlan_proto, u16 vlan_tci)
{
skb->vlan_proto = vlan_proto;
skb->vlan_tci = vlan_tci;
}
What we need to do to fix this problem (assuming this is the problem) is
to stop using skb->vlan_all as temporary storage for driver affairs, and
just create some local variables that serve the same purpose, but
hopefully better. Instead of calling skb_vlan_tag_present(), let's look
at a boolean has_hwaccel_tag which we set to true when the RX DMA
descriptors have something. Disambiguate based on netdev_uses_dsa()
whether this is a VLAN or DSA hwaccel tag, and only call
__vlan_hwaccel_put_tag() if we're certain it's a VLAN tag.
Arınç confirms that the treatment works, so this validates the
assumption.
Link: https://lore.kernel.org/netdev/704f3a72-fc9e-714a-db54-272e17612637@arinc9.com/
Fixes: 2d7605a729 ("net: ethernet: mtk_eth_soc: enable hardware DSA untagging")
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unsupported port speed can be set and cause error. Now fixing it
and return an error if setting unsupported speed.
This fix depends on the following, which was included in v6.2-rc1:
commit a61474c41e ("nfp: ethtool: support reporting link modes").
Fixes: 7c69873727 ("nfp: add support for .set_link_ksettings()")
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameters 'queue_index' and 'napi_id' are passed in a swapped order.
Fix it here.
Fixes: 23233e577e ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The special tag is only enabled when the first MAC uses DSA. However, it
must be enabled when any MAC uses DSA. Change the check accordingly.
This fixes hardware DSA untagging not working on the second MAC of the
MT7621 and MT7623 SoCs, and likely other SoCs too. Therefore, remove the
check that disables hardware DSA untagging for the second MAC of the MT7621
and MT7623 SoCs.
Fixes: a1f47752fd ("net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC")
Co-developed-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Richard van Schagen <richard@routerhints.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-02-06 (ice)
This series contains updates to ice driver only.
Ani removes WQ_MEM_RECLAIM flag from workqueue to resolve
check_flush_dependency warning.
Michal fixes KASAN out-of-bounds warning.
Brett corrects behaviour for port VLAN Rx filters to prevent receiving
of unintended traffic.
Dan Carpenter fixes possible off by one issue.
Zhang Changzhong adjusts error path for switch recipe to prevent memory
leak.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: switch: fix potential memleak in ice_add_adv_recipe()
ice: Fix off by one in ice_tc_forward_to_queue()
ice: Fix disabling Rx VLAN filtering with port VLAN enabled
ice: fix out-of-bounds KASAN warning in virtchnl
ice: Do not use WQ_MEM_RECLAIM flag for workqueue
====================
Link: https://lore.kernel.org/r/20230206232934.634298-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After calling irq_set_affinity_and_hint(), the cpumask pointer is
saved in desc->affinity_hint, and will be used later when reading
/proc/irq/<num>/affinity_hint. So the cpumask variable needs to be
persistent. Otherwise, we are accessing freed memory when reading
the affinity_hint file.
Also, need to clear affinity_hint before free_irq(), otherwise there
is a one-time warning and stack trace during module unloading:
[ 243.948687] WARNING: CPU: 10 PID: 1589 at kernel/irq/manage.c:1913 free_irq+0x318/0x360
...
[ 243.948753] Call Trace:
[ 243.948754] <TASK>
[ 243.948760] mana_gd_remove_irqs+0x78/0xc0 [mana]
[ 243.948767] mana_gd_remove+0x3e/0x80 [mana]
[ 243.948773] pci_device_remove+0x3d/0xb0
[ 243.948778] device_remove+0x46/0x70
[ 243.948782] device_release_driver_internal+0x1fe/0x280
[ 243.948785] driver_detach+0x4e/0xa0
[ 243.948787] bus_remove_driver+0x70/0xf0
[ 243.948789] driver_unregister+0x35/0x60
[ 243.948792] pci_unregister_driver+0x44/0x90
[ 243.948794] mana_driver_exit+0x14/0x3fe [mana]
[ 243.948800] __do_sys_delete_module.constprop.0+0x185/0x2f0
To fix the bug, use the persistent mask, cpumask_of(cpu#), and set
affinity_hint to NULL before freeing the IRQ, as required by free_irq().
Cc: stable@vger.kernel.org
Fixes: 71fa6887ee ("net: mana: Assign interrupts to CPUs based on NUMA nodes")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1675718929-19565-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, remove and reload flows can run in parallel to module cleanup.
This design is error prone. For example: aux_drivers callbacks are called
from both cleanup and remove flows with different lockings, which can
cause a deadlock[1].
Hence, serialize module cleanup with reload and remove.
[1]
cleanup remove
------- ------
auxiliary_driver_unregister();
devl_lock()
auxiliary_device_delete(mlx5e_aux)
device_lock(mlx5e_aux)
devl_lock()
device_lock(mlx5e_aux)
Fixes: 912cebf420 ("net/mlx5e: Connect ethernet part to auxiliary bus")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752 ("net/mlx5: Add support for fw live patch event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, an independent page counter is used for tracking memory usage
for each function type such as VF, PF and host PF (DPU).
For better code-readibilty, use a single array that stores
the number of allocated memory pages for each function type.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d5 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Moving to switchdev mode with rx-vlan-filter on and then setting it off
causes the kernel to crash since fs->vlan is freed during nic profile
cleanup flow.
RX VLAN filtering is not supported in switchdev mode so unset it when
changing to switchdev and restore its value when switching back to
legacy.
trace:
[] RIP: 0010:mlx5e_disable_cvlan_filter+0x43/0x70
[] set_feature_cvlan_filter+0x37/0x40 [mlx5_core]
[] mlx5e_handle_feature+0x3a/0x60 [mlx5_core]
[] mlx5e_set_features+0x6d/0x160 [mlx5_core]
[] __netdev_update_features+0x288/0xa70
[] ethnl_set_features+0x309/0x380
[] ? __nla_parse+0x21/0x30
[] genl_family_rcv_msg_doit.isra.17+0x110/0x150
[] genl_rcv_msg+0x112/0x260
[] ? features_reply_size+0xe0/0xe0
[] ? genl_family_rcv_msg_doit.isra.17+0x150/0x150
[] netlink_rcv_skb+0x4e/0x100
[] genl_rcv+0x24/0x40
[] netlink_unicast+0x1ab/0x290
[] netlink_sendmsg+0x257/0x4f0
[] sock_sendmsg+0x5c/0x70
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
SWITCHDEV_FDB_ADD_TO_BRIDGE event handler that updates FDB entry 'lastuse'
field is only executed for eswitch that owns the entry. However, if peer
entry processed packets at least once it will have hardware counter 'used'
value greater than entry 'lastuse' from that point on, which will cause FDB
entry not being aged out.
Process the event on all eswitch instances.
Fixes: ff9b752146 ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Selecting builder should be protected by the lock to prevent the case
where a new rule sets a builder in the nic_matcher while the previous
rule is still using the nic_matcher.
Fixing this issue and cleaning the error flow.
Fixes: b9b81e1e93 ("net/mlx5: DR, For short chains of STEs, avoid allocating ste_arr dynamically")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
rq->hw_mtu is used in function en_rx.c/mlx5e_skb_from_cqe_mpwrq_linear()
to catch oversized packets. If FCS is concatenated to the end of the
packet then the check should be updated accordingly.
Rx rings initialization (mlx5e_init_rxq_rq()) invoked for every new set
of channels, as part of mlx5e_safe_switch_params(), unknowingly if it
runs with default configuration or not. Current rq->hw_mtu
initialization assumes default configuration and ignores
params->scatter_fcs_en flag state.
Fix this, by accounting for params->scatter_fcs_en flag state during
rq->hw_mtu initialization.
In addition, updating rq->hw_mtu value during ingress traffic might
lead to packets drop and oversize_pkts_sw_drop counter increase with no
good reason. Hence we remove this optimization and switch the set of
channels with a new one, to make sure we don't get false positives on
the oversize_pkts_sw_drop counter.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
With a command such as the following:
tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
action vlan modify id 300 \
action goto chain $(IS2 0 0)
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e610 ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de11 ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When ice_add_special_words() fails, the 'rm' is not released, which will
lead to a memory leak. Fix this up by going to 'err_unroll' label.
Compile tested only.
Fixes: 8b032a55c1 ("ice: low level support for tunnels")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
The > comparison should be >= to prevent reading one element beyond
the end of the array.
The "vsi->num_rxq" is not strictly speaking the number of elements in
the vsi->rxq_map[] array. The array has "vsi->alloc_rxq" elements and
"vsi->num_rxq" is less than or equal to the number of elements in the
array. The array is allocated in ice_vsi_alloc_arrays(). It's still
an off by one but it might not access outside the end of the array.
Fixes: 143b86f346 ("ice: Enable RX queue selection using skbedit action")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
If the user turns on the vf-true-promiscuous-support flag, then Rx VLAN
filtering will be disabled if the VF requests to enable promiscuous
mode. When the VF is in a port VLAN, this is the incorrect behavior
because it will allow the VF to receive traffic outside of its port VLAN
domain. Fortunately this only resulted in the VF(s) receiving broadcast
traffic outside of the VLAN domain because all of the VLAN promiscuous
rules are based on the port VLAN ID. Fix this by setting the
.disable_rx_filtering VLAN op to a no-op when a port VLAN is enabled on
the VF.
Also, make sure to make this fix for both Single VLAN Mode and Double
VLAN Mode enabled devices.
Fixes: c31af68a1b ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check all ports instead of just port_count ports. PTP init was only
checking ports 0 to port_count. If the hardware ports are not mapped
starting from 0 then they would be missed, e.g. if only ports 20-30 were
mapped it would attempt to init ports 0-10, resulting in NULL pointers
when attempting to timestamp. Now it will init all mapped ports.
Fixes: 70dfe25cd8 ("net: sparx5: Update extraction/injection for timestamping")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one version of the HW there is a remote possibility that it
will miss the doorbell ring. This adds a bit of protection to
be sure we don't stall a queue from a missed doorbell.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Allen Hubbe <allen.hubbe@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure the q+cq alloc for NotifyQ is clearly documented
and don't bother with unnecessary local variables.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clear the interrupt credits before enabling the queue rather
than after to be sure that the enabled queue starts at 0 and
that we don't wipe away possible credits after enabling the
queue.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Neel Patel <neel.patel@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After calling fwnode_phy_find_device(), the phy device refcount is
incremented. Then, when the phy device is attached to a netdev with
phy_attach_direct(), the refcount is also incremented but only
decremented in the caller if phy_attach_direct() fails. Move
phy_device_free() before the "if" to always release it correctly.
Indeed, either phy_attach_direct() failed and we don't want to keep a
reference to the phydev or it succeeded and a reference has been taken
internally.
Fixes: 25396f680d ("net: phylink: introduce phylink_fwnode_phy_connect()")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no IRQ handling (even the SGMII supports it).
Enable polling to support SFP ports.
Fixes: 14a44ab033 ("net: mtk_eth_soc: partially convert to phylink_pcs")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: changed "1" => "true" ]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic of the duplex bit is inverted. Setting it means half
duplex, not full duplex.
Fix and rename macro to avoid confusion.
Fixes: 7e53837269 ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code expect the PHY to be in power down which is only true after reset.
Allow changes of the SGMII parameters more than once.
Only power down when reconfiguring to avoid bouncing the link when there's
no reason to - based on code from Russell King.
There are cases when the SGMII_PHYA_PWD register contains 0x9 which
prevents SGMII from working. The SGMII still shows link but no traffic
can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
taken from a good working state of the SGMII interface.
Fixes: 42c03844e9 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: rebased and squashed into one patch ]
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
can 2023-02-02
The first patch is by Ziyang Xuan and removes a errant WARN_ON_ONCE()
in the CAN J1939 protocol.
The next 3 patches are by Oliver Hartkopp. The first 2 target the CAN
ISO-TP protocol and fix the state machine with respect to signals and
a regression found by the syzbot.
The last patch is by me an missing assignment during the ethtool ring
configuration callback.
* tag 'linux-can-fixes-for-6.2-20230202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
can: isotp: split tx timer into transmission and timeout
can: isotp: handle wait_event_interruptible() return values
can: raw: fix CAN FD frame transmissions over CAN XL devices
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
====================
Link: https://lore.kernel.org/r/20230202094135.2293939-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cited commit in fixes tag frees rxq xdp info while RQ NAPI is
still enabled and packet processing may be ongoing.
Follow the mirror sequence of open() in the stop() callback.
This ensures that when rxq info is unregistered, no rx
packet processing is ongoing.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20230202163516.12559-1-parav@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netvsc_dma_map() and netvsc_dma_unmap() currently check the cp_partial
flag and adjust the page_count so that pagebuf entries for the RNDIS
portion of the message are skipped when it has already been copied into
a send buffer. But this adjustment has already been made by code in
netvsc_send(). The duplicate adjustment causes some pagebuf entries to
not be mapped. In a normal VM, this doesn't break anything because the
mapping doesn’t change the PFN. But in a Confidential VM,
dma_map_single() does bounce buffering and provides a different PFN.
Failing to do the mapping causes the wrong PFN to be passed to Hyper-V,
and various errors ensue.
Fix this by removing the duplicate adjustment in netvsc_dma_map() and
netvsc_dma_unmap().
Fixes: 846da38de0 ("net: netvsc: Add Isolation VM support for netvsc driver")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1675135986-254490-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Meson G12A Internal PHY does not support standard IEEE MMD extended
register access, therefore add generic dummy stubs to fail the read and
write MMD calls. This is necessary to prevent the core PHY code from
erroneously believing that EEE is supported by this PHY even though this
PHY does not support EEE, as MMD register access returns all FFFFs.
Fixes: 5c3407abb3 ("net: phy: meson-gxl: add g12a support")
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230130231402.471493-1-cphealy@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
