mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
synced 2026-02-24 05:25:18 -05:00
ff64e078e45faee50cc6ca7900a3520e8ff1c79e
80932 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Alex Elder
|
a812b09a6b |
dt-bindings: pci: spacemit: Introduce PCIe host controller
Add the Devicetree binding for the PCIe Root Complex found on the SpacemiT K1 SoC. This Root Complex is derived from the Synopsys Designware PCIe IP. It supports up to three PCIe ports operating at PCIe link speed up to 5 GT/sec. One of the ports uses a combo PHY, which is typically used to support a USB3 port. Signed-off-by: Alex Elder <elder@riscstar.com> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Tested-by: Jason Montleon <jmontleo@redhat.com> Tested-by: Johannes Erdfelt <johannes@erdfelt.com> Tested-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Rob Herring (Arm) <robh@kernel.org> Link: https://patch.msgid.link/20251113214540.2623070-4-elder@riscstar.com |
||
|
Linus Torvalds
|
98906f9d85 |
Merge tag 'rtc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni: "This cycle, we have a new RTC driver, for the SpacemiT P1. The optee driver gets alarm support. We also get a fix for a race condition that was fairly rare unless while stress testing the alarms. Subsystem: - Fix race when setting alarm - Ensure alarm irq is enabled when UIE is enabled - remove unneeded 'fast_io' parameter in regmap_config New driver: - SpacemiT P1 RTC Drivers: - efi: Remove wakeup functionality - optee: add alarms support - s3c: Drop support for S3C2410 - zynqmp: Restore alarm functionality after kexec transition" * tag 'rtc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (29 commits) rtc: interface: Ensure alarm irq is enabled when UIE is enabled rtc: tps6586x: Fix initial enable_irq/disable_irq balance rtc: cpcap: Fix initial enable_irq/disable_irq balance rtc: isl12022: Fix initial enable_irq/disable_irq balance rtc: interface: Fix long-standing race when setting alarm rtc: pcf2127: fix watchdog interrupt mask on pcf2131 rtc: zynqmp: Restore alarm functionality after kexec transition rtc: amlogic-a4: Optimize global variables rtc: sd2405al: Add I2C address. rtc: Kconfig: move symbols to proper section rtc: optee: make optee_rtc_pm_ops static rtc: optee: Fix error code in optee_rtc_read_alarm() rtc: optee: fix error code in probe() dt-bindings: rtc: Convert apm,xgene-rtc to DT schema rtc: spacemit: support the SpacemiT P1 RTC rtc: optee: add alarm related rtc ops to optee rtc driver rtc: optee: remove unnecessary memory operations rtc: optee: fix memory leak on driver removal rtc: x1205: Fix Xicor X1205 vendor prefix dt-bindings: rtc: Fix Xicor X1205 vendor prefix ... |
||
|
Linus Torvalds
|
9591fdb061 |
Merge tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more x86 updates from Borislav Petkov: - Remove a bunch of asm implementing condition flags testing in KVM's emulator in favor of int3_emulate_jcc() which is written in C - Replace KVM fastops with C-based stubs which avoids problems with the fastop infra related to latter not adhering to the C ABI due to their special calling convention and, more importantly, bypassing compiler control-flow integrity checking because they're written in asm - Remove wrongly used static branches and other ugliness accumulated over time in hyperv's hypercall implementation with a proper static function call to the correct hypervisor call variant - Add some fixes and modifications to allow running FRED-enabled kernels in KVM even on non-FRED hardware - Add kCFI improvements like validating indirect calls and prepare for enabling kCFI with GCC. Add cmdline params documentation and other code cleanups - Use the single-byte 0xd6 insn as the official #UD single-byte undefined opcode instruction as agreed upon by both x86 vendors - Other smaller cleanups and touchups all over the place * tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits) x86,retpoline: Optimize patch_retpoline() x86,ibt: Use UDB instead of 0xEA x86/cfi: Remove __noinitretpoline and __noretpoline x86/cfi: Add "debug" option to "cfi=" bootparam x86/cfi: Standardize on common "CFI:" prefix for CFI reports x86/cfi: Document the "cfi=" bootparam options x86/traps: Clarify KCFI instruction layout compiler_types.h: Move __nocfi out of compiler-specific header objtool: Validate kCFI calls x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware x86/fred: Install system vector handlers even if FRED isn't fully enabled x86/hyperv: Use direct call to hypercall-page x86/hyperv: Clean up hv_do_hypercall() KVM: x86: Remove fastops KVM: x86: Convert em_salc() to C KVM: x86: Introduce EM_ASM_3WCL KVM: x86: Introduce EM_ASM_1SRC2 KVM: x86: Introduce EM_ASM_2CL KVM: x86: Introduce EM_ASM_2W ... |
||
|
Linus Torvalds
|
f76b1683d1 |
Merge tag 'devicetree-fixes-for-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring: - Allow child nodes on renesas-bsc bus binding - Drop node name pattern on allwinner,sun50i-a64-de2 bus binding - Switch DT patchwork to kernel.org from ozlabs.org - Fix some typos in docs and bindings - Fix reference count in PCI node unittest * tag 'devicetree-fixes-for-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: dt-bindings: bus: renesas-bsc: allow additional properties dt-bindings: bus: allwinner,sun50i-a64-de2: don't check node names MAINTAINERS: Move DT patchwork to kernel.org of: unittest: Fix device reference count leak in of_unittest_pci_node_verify of: doc: Fix typo in doc comments. dt-bindings: mmc: Correct typo "upto" to "up to" |
||
|
Wolfram Sang
|
ce740955b2 |
dt-bindings: bus: renesas-bsc: allow additional properties
Allow additional properties to enable devices attached to the bus.
Fixes warnings like these:
arch/arm/boot/dts/renesas/sh73a0-kzm9g.dtb: bus@fec10000 (renesas,bsc-sh73a0): Unevaluated properties are not allowed ('ethernet@10000000' was unexpected)
arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dtb: bus@fec10000 (renesas,bsc-r8a73a4): Unevaluated properties are not allowed ('ethernet@8000000', 'flash@0' were unexpected)
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
||
|
Wolfram Sang
|
f7045387a6 |
dt-bindings: bus: allwinner,sun50i-a64-de2: don't check node names
Node names are already and properly checked by the core schema. No need to do it again. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> [robh: Also drop [A-F] in unit address] Signed-off-by: Rob Herring (Arm) <robh@kernel.org> |
||
|
Linus Torvalds
|
fdfa38e95e |
Merge tag 'sound-fix-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai: "A few more small fixes for 6.18-rc1. Most of changes are about ASoC Intel and SOF drivers, while a few other device-specific fixes are found for HD-audio, USB-audio, ASoC RT722VB and Meson" * tag 'sound-fix-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ASoC: rt722: add settings for rt722VB ASoC: meson: aiu-encoder-i2s: fix bit clock polarity ALSA: usb: fpc: replace kmalloc_array followed by copy_from_user with memdup_array_user ALSA: hda/tas2781: Enable init_profile_id for device initialization ALSA: emu10k1: Fix typo in docs ALSA: hda/realtek: Add quirk for ASUS ROG Zephyrus Duo ASoC: SOF: Intel: Read the LLP via the associated Link DMA channel ASoC: SOF: ipc4-pcm: do not report invalid delay values ASoC: SOF: sof-audio: add dev_dbg_ratelimited wrapper ASoC: SOF: Intel: hda-pcm: Place the constraint on period time instead of buffer time ASoC: SOF: ipc4-topology: Account for different ChainDMA host buffer size ASoC: SOF: ipc4-topology: Correct the minimum host DMA buffer size ASoC: SOF: ipc4-pcm: fix start offset calculation for chain DMA ASoC: SOF: ipc4-pcm: fix delay calculation when DSP resamples ASoC: SOF: ipc3-topology: Fix multi-core and static pipelines tear down ALSA: hda/hdmi: Add pin fix for HP ProDesk model |
||
|
Linus Torvalds
|
06a88f4799 |
Merge tag 'fbdev-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller: "Beside the usual bunch of smaller bug fixes, the majority of changes were by Zsolt Kajtar to improve the s3fb driver. Bug fixes: - Bounds checking to fix vmalloc-out-of-bounds (Albin Babu Varghese) - Fix logic error in "offb" name match (Finn Thain) - simplefb: Fix use after free in (Janne Grunau) - s3fb: Various fixes and powersave improvements (Zsolt Kajtar) Enhancements & code cleanups: - Various fixes in the documentation (Bagas Sanjaya) - Use string choices helpers (Chelsy Ratnawat) - xenfb: Use vmalloc_array to simplify code (Qianfeng Rong) - mb862xxfb: use signed type for error codes (Qianfeng Rong) - Make drivers depend on LCD_CLASS_DEVICE (Thomas Zimmermann) - radeonfb: Remove stale product link in Kconfig (Sukrut Heroorkar)" * tag 'fbdev-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: fbdev: Fix logic error in "offb" name match fbdev: Add bounds checking in bit_putcs to fix vmalloc-out-of-bounds fbdev: Make drivers depend on LCD_CLASS_DEVICE fbdev: radeonfb: Remove stale product link in Kconfig Documentation: fb: Retitle driver docs Documentation: fb: ep93xx: Demote section headings Documentation: fb: Split toctree fbdev: simplefb: Fix use after free in simplefb_detach_genpds() fbdev: s3fb: Revert mclk stop in suspend fbdev: mb862xxfb: Use int type to store negative error codes fbdev: Use string choices helpers fbdev: core: Fix ubsan warning in pixel_to_pat fbdev: s3fb: Implement 1 and 2 BPP modes, improve 4 BPP fbdev: s3fb: Implement powersave for S3 FB fbdev: xenfb: Use vmalloc_array to simplify code |
||
|
Linus Torvalds
|
aac3190332 |
Merge tag 'i2c-for-6.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- Second part of rtl9300 updates since dependencies are in now:
- general cleanups
- implement block read/write support
- add RTL9310 support
- DT schema conversion of hix5hd2 binding
- namespace cleanup for i2c-algo-pca
- minor simplification for mt65xx
* tag 'i2c-for-6.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: hisilicon,hix5hd2: convert to DT schema
i2c: mt65xx: convert set_speed function to void
i2c: rename wait_for_completion callback to wait_for_completion_cb
i2c: rtl9300: add support for RTL9310 I2C controller
dt-bindings: i2c: realtek,rtl9301-i2c: extend for RTL9310 support
i2c: rtl9300: use scoped guard instead of explicit lock/unlock
i2c: rtl9300: separate xfer configuration and execution
i2c: rtl9300: do not set read mode on every transfer
i2c: rtl9300: move setting SCL frequency to config_io
i2c: rtl9300: rename internal sda_pin to sda_num
dt-bindings: i2c: realtek,rtl9301-i2c: fix wording and typos
i2c: rtl9300: use regmap fields and API for registers
i2c: rtl9300: Implement I2C block read and write
|
||
|
Kael D'Alcamo
|
eb4faf6343 |
dt-bindings: i2c: hisilicon,hix5hd2: convert to DT schema
Convert the Devicetree binding documentation for hisilicon,hix5hd2-i2c from plain text to DT binding schema. Signed-off-by: Kael D'Alcamo <dev@kael-k.io> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> |
||
|
Linus Torvalds
|
cd5a0afbdf |
Merge tag 'mailbox-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- Qualcomm: add Glymur CPUCP mailbox binding
- Xilinx Zynq: misc cleanup
- MediaTek:
- add new GPUEB mailbox driver
- cmdq: remove pm_runtime calls from send_data
- gce: make clock-names optional
- misc:
- change mailbox-altera maintainer
- remove redundant 'fast_io' in regmap_config
- mhuv3: Remove no_free_ptr
* tag 'mailbox-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox: mtk-cmdq: Remove pm_runtime APIs from cmdq_mbox_send_data()
mailbox: add MediaTek GPUEB IPI mailbox
dt-bindings: mailbox: Add MT8196 GPUEB Mailbox
mailbox: zynqmp-ipi: Fix SGI cleanup on unbind
mailbox: zynqmp-ipi: Fix out-of-bounds access in mailbox cleanup loop
mailbox: zynqmp-ipi: Remove dev.parent check in zynqmp_ipi_free_mboxes
mailbox: zynqmp-ipi: Remove redundant mbox_controller_unregister() call
mailbox: remove unneeded 'fast_io' parameter in regmap_config
dt-bindings: mailbox: mediatek,gce-mailbox: Make clock-names optional
dt-bindings: mailbox: qcom: Document Glymur CPUCP mailbox controller binding
MAINTAINERS: Change mailbox-altera maintainer
mailbox: arm_mhuv3: Remove no_free_ptr() to maintain the original form of the pointer
|
||
|
Linus Torvalds
|
ed4d6e9246 |
Merge tag 'vfio-v6.18-rc1-pt2' of https://github.com/awilliam/linux-vfio
Pull more VFIO updates from Alex Williamson: - Optimizations for DMA map and unmap opertions through the type1 vfio IOMMU backend. This uses various means of batching and hints from the mm structures to improve efficiency and therefore performance, resulting in a significant speedup for huge page use cases (Li Zhe) - Expose supported device migration features through debugfs (Cédric Le Goater) * tag 'vfio-v6.18-rc1-pt2' of https://github.com/awilliam/linux-vfio: vfio: Dump migration features under debugfs vfio/type1: optimize vfio_unpin_pages_remote() vfio/type1: introduce a new member has_rsvd for struct vfio_dma vfio/type1: batch vfio_find_vpfn() in function vfio_unpin_pages_remote() vfio/type1: optimize vfio_pin_pages_remote() mm: introduce num_pages_contiguous() |
||
|
Linus Torvalds
|
99cedb6b8f |
Merge tag 'input-for-v6.18-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- Conversions to yaml/json schema and fixes for input-related device
tree bindings
- New drivers:
- Awinic AW86927 haptic chip
- Hynitron CST816x series controller
- Himax HX852x(ES) touchscreen controller
- Fix uinput to not leak kernel memory via a gap in
uinput_ff_upload_compat structure
- Prevent overflow in pressure calculation in tsc2007 driver causing
phantom touches
- Make the Atmel maxTouch driver support generic touchscreen
configuration (flip, rotate, etc)
- Drop support for platform data in tca8418_keypad, pxa27x-keypad,
spear-keyboard and twl4030_keypad drivers, they all now rely on
generic device properties for configuration
- Other assorted changes and fixes
* tag 'input-for-v6.18-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: atmel_mxt_ts - allow reset GPIO to sleep
Input: aw86927 - fix error code in probe()
Input: psxpad-spi - add a check for the return value of spi_setup()
Input: uinput - zero-initialize uinput_ff_upload_compat to avoid info leak
Input: aw86927 - add driver for Awinic AW86927
dt-bindings: input: Add Awinic AW86927
dt-bindings: touchscreen: remove touchscreen.txt
dt-bindings: arm: bcm: raspberrypi,bcm2835-firmware: Add touchscreen child node
dt-bindings: touchscreen: convert eeti bindings to json schema
Input: pm8941-pwrkey - disable wakeup for resin by default
dt-bindings: input: pm8941-pwrkey: Document wakeup-source property
Input: add driver for Hynitron CST816x series
dt-bindings: input: touchscreen: add hynitron cst816x series
Input: imx6ul_tsc - set glitch threshold by DTS property
dt-bindings: touchscreen: fsl,imx6ul-tsc: support glitch thresold
dt-bindings: touchscreen: add debounce-delay-us property
Input: ps2-gpio - fix typo
Input: atmel_mxt_ts - add support for generic touchscreen configurations
dt-bindings: input: maxtouch: add common touchscreen properties
dt-bindings: touchscreen: convert zet6223 bindings to json schema
...
|
||
|
Linus Torvalds
|
abdf766d14 |
Merge tag 'pm-6.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are cpufreq fixes and cleanups on top of the material merged
previously, a power management core code fix and updates of the
runtime PM framework including unit tests, documentation updates and
introduction of auto-cleanup macros for runtime PM "resume and get"
and "get without resuming" operations.
Specifics:
- Make cpufreq drivers setting the default CPU transition latency to
CPUFREQ_ETERNAL specify a proper default transition latency value
instead which addresses a regression introduced during the 6.6
cycle that broke CPUFREQ_ETERNAL handling (Rafael Wysocki)
- Make the cpufreq CPPC driver use a proper transition delay value
when CPUFREQ_ETERNAL is returned by cppc_get_transition_latency()
to indicate an error condition (Rafael Wysocki)
- Make cppc_get_transition_latency() return a negative error code to
indicate error conditions instead of using CPUFREQ_ETERNAL for this
purpose and drop CPUFREQ_ETERNAL that has no other users (Rafael
Wysocki, Gopi Krishna Menon)
- Fix device leak in the mediatek cpufreq driver (Johan Hovold)
- Set target frequency on all CPUs sharing a policy during frequency
updates in the tegra186 cpufreq driver and make it initialize all
cores to max frequencies (Aaron Kling)
- Rust cpufreq helper cleanup (Thorsten Blum)
- Make pm_runtime_put*() family of functions return 1 when the given
device is already suspended which is consistent with the
documentation (Brian Norris)
- Add basic kunit tests for runtime PM API contracts and update
return values in kerneldoc comments for the runtime PM API (Brian
Norris, Dan Carpenter)
- Add auto-cleanup macros for runtime PM "resume and get" and "get
without resume" operations, use one of them in the PCI core and
drop the existing "free" macro introduced for similar purpose, but
somewhat cumbersome to use (Rafael Wysocki)
- Make the core power management code avoid waiting on device links
marked as SYNC_STATE_ONLY which is consistent with the handling of
those device links elsewhere (Pin-yen Lin)"
* tag 'pm-6.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
docs/zh_CN: Fix malformed table
docs/zh_TW: Fix malformed table
PM: runtime: Fix error checking for kunit_device_register()
PM: runtime: Introduce one more usage counter guard
cpufreq: Drop unused symbol CPUFREQ_ETERNAL
ACPI: CPPC: Do not use CPUFREQ_ETERNAL as an error value
cpufreq: CPPC: Avoid using CPUFREQ_ETERNAL as transition delay
cpufreq: Make drivers using CPUFREQ_ETERNAL specify transition latency
PM: runtime: Drop DEFINE_FREE() for pm_runtime_put()
PCI/sysfs: Use runtime PM guard macro for auto-cleanup
PM: runtime: Add auto-cleanup macros for "resume and get" operations
cpufreq: tegra186: Initialize all cores to max frequencies
cpufreq: tegra186: Set target frequency for all cpus in policy
rust: cpufreq: streamline find_supply_names
cpufreq: mediatek: fix device leak on probe failure
PM: sleep: Do not wait on SYNC_STATE_ONLY device links
PM: runtime: Update kerneldoc return codes
PM: runtime: Make put{,_sync}() return 1 when already suspended
PM: runtime: Add basic kunit tests for API contracts
|
||
|
Linus Torvalds
|
522ba450b5 |
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd: "There's a bunch of patches here across drivers/clk/ to migrate drivers to use struct clk_ops::determine_rate() instead of the round_rate() one so that we can remove the round_rate clk_op entirely. Brian has taken up that task which nobody else has wanted to do for close to a decade. Thanks Brian! This is all prerequisite work to get to the real task of improving the clk rate setting process. Once we have determine_rate() used everywhere, we'll be able to do things like chain the rate request structs in linked lists to order the rate setting operations or add more parameters without having to change every clk driver in existence. It's also nice to not have multiple ways to do something which just causes confusion for clk driver authors. Overall I'm glad this is getting done. Beyond this change we also have a tweak to the clk_lookup() function in the core framework to use hashing on the clk name instead of a clk tree walk with string comparisons. We _still_ rely on the clk name to be unique, because historically we've used globally unique strings to describe the clk tree topology. This tree walk becomes increasingly slow as more clks are added to the system. Searching from the roots for a duplicate is simple but pretty dumb and it wastes boot time so we're using a hash table as an improvement. Ideally we wouldn't rely on the strings to be unique at all, relegating them to simply debug information, but that is future work that will likely require some sort of Kconfig knob indicating strings aren't used for topology description. Outside of the core framework changes we have the usual new SoC support and fixes to clk drivers for things that were discovered once the clks were used by consumer drivers. Nothing in particular is jumping out at me in the "misc" pile, except maybe the Amlogic driver that has gone through a refactoring. That series got a fix from testing in -next though so it seems likely that things have been getting good test coverage for a couple weeks already" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (299 commits) clk: microchip: core: remove duplicate roclk_determine_rate() reset: aspeed: register AST2700 reset auxiliary bus device dt-bindings: clock: ast2700: modify soc0/1 clock define clk: tegra: do not overallocate memory for bpmp clocks clk: ep93xx: Use int type to store negative error codes clk: nxp: Fix pll0 rate check condition in LPC18xx CGU driver clk: loongson2: Add clock definitions for Loongson-2K0300 SoC clk: loongson2: Avoid hardcoding firmware name of the reference clock clk: loongson2: Allow zero divisors for dividers clk: loongson2: Support scale clocks with an alternative mode clk: loongson2: Allow specifying clock flags for gate clock dt-bindings: clock: loongson2: Add Loongson-2K0300 compatible clk: clocking-wizard: Fix output clock register offset for Versal platforms clk: xilinx: Optimize divisor search in clk_wzrd_get_divisors_ver() clk: mmp: pxa1908: Instantiate power driver through auxiliary bus clk: s2mps11: add support for S2MPG10 PMIC clock dt-bindings: clock: samsung,s2mps11: add s2mpg10 dt-bindings: stm32: cosmetic fixes for STM32MP25 clock and reset bindings clk: stm32: introduce clocks for STM32MP21 platform dt-bindings: stm32: add STM32MP21 clocks and reset bindings ... |
||
|
Linus Torvalds
|
971199ad2a |
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon: - Preserve old 'tt_core' UAPI for Hisilicon L3C PMU driver - Ensure linear alias of kprobes instruction page is not writable - Fix kernel stack unwinding from BPF - Fix build warnings from the Fujitsu uncore PMU documentation - Fix hang with deferred 'struct page' initialisation and MTE - Consolidate KPTI page-table re-writing code * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: mte: Do not flag the zero page as PG_mte_tagged docs: perf: Fujitsu: Fix htmldocs build warnings and errors arm64: mm: Move KPTI helpers to mmu.c tracing: Fix the bug where bpf_get_stackid returns -EFAULT on the ARM64 arm64: kprobes: call set_memory_rox() for kprobe page drivers/perf: hisi: Add tt_core_deprecated for compatibility |
||
|
Rafael J. Wysocki
|
53d4d315d4 |
Merge branch 'pm-cpufreq'
Merge cpufreq fixes and cleanups, mostly on top of those fixes, for 6.18-rc1: - Make cpufreq drivers setting the default CPU transition latency to CPUFREQ_ETERNAL specify a proper default transition latency value instead which addresses a regression introduced during the 6.6 cycle that broke CPUFREQ_ETERNAL handling (Rafael Wysocki) - Make the cpufreq CPPC driver use a proper transition delay value when CPUFREQ_ETERNAL is returned by cppc_get_transition_latency() to indicate an error condition (Rafael Wysocki) - Make cppc_get_transition_latency() return a negative error code to indicate error conditions instead of using CPUFREQ_ETERNAL for this purpose and drop CPUFREQ_ETERNAL that has no other users (Rafael Wysocki, Gopi Krishna Menon) - Fix device leak in the mediatek cpufreq driver (Johan Hovold) - Set target frequency on all CPUs sharing a policy during frequency updates in the tegra186 cpufreq driver and make it initialize all cores to max frequencies (Aaron Kling) - Rust cpufreq helper cleanup (Thorsten Blum) * pm-cpufreq: docs/zh_CN: Fix malformed table docs/zh_TW: Fix malformed table cpufreq: Drop unused symbol CPUFREQ_ETERNAL ACPI: CPPC: Do not use CPUFREQ_ETERNAL as an error value cpufreq: CPPC: Avoid using CPUFREQ_ETERNAL as transition delay cpufreq: Make drivers using CPUFREQ_ETERNAL specify transition latency cpufreq: tegra186: Initialize all cores to max frequencies cpufreq: tegra186: Set target frequency for all cpus in policy rust: cpufreq: streamline find_supply_names cpufreq: mediatek: fix device leak on probe failure |
||
|
Nicolas Frattaroli
|
d3e35a151a |
dt-bindings: mailbox: Add MT8196 GPUEB Mailbox
The MediaTek MT8196 SoC includes an embedded MCU referred to as "GPUEB", acting as glue logic to control power and frequency of the Mali GPU. This MCU runs special-purpose firmware for this use, and the main application processor communicates with it through a mailbox. Add a binding that describes this mailbox. Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Acked-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> |
||
|
AngeloGioacchino Del Regno
|
426f4e9414 |
dt-bindings: mailbox: mediatek,gce-mailbox: Make clock-names optional
The GCE Mailbox needs only one clock and the clock-names can be used only by the driver (which, for instance, does not use it), and this is true for all of the currently supported MediaTek SoCs. Stop requiring to specify clock-names on all non-MT8195 GCEs. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Acked-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> |
||
|
Sibi Sankar
|
526ce9eb45 |
dt-bindings: mailbox: qcom: Document Glymur CPUCP mailbox controller binding
Document CPU Control Processor (CPUCP) mailbox controller for Qualcomm Glymur SoCs. It is software compatible with X1E80100 CPUCP mailbox controller hence fallback to it. Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com> Acked-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> |
||
|
Linus Torvalds
|
256e341706 |
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull x86 kvm updates from Paolo Bonzini:
"Generic:
- Rework almost all of KVM's exports to expose symbols only to KVM's
x86 vendor modules (kvm-{amd,intel}.ko and PPC's kvm-{pr,hv}.ko
x86:
- Rework almost all of KVM x86's exports to expose symbols only to
KVM's vendor modules, i.e. to kvm-{amd,intel}.ko
- Add support for virtualizing Control-flow Enforcement Technology
(CET) on Intel (Shadow Stacks and Indirect Branch Tracking) and AMD
(Shadow Stacks).
It is worth noting that while SHSTK and IBT can be enabled
separately in CPUID, it is not really possible to virtualize them
separately. Therefore, Intel processors will really allow both
SHSTK and IBT under the hood if either is made visible in the
guest's CPUID. The alternative would be to intercept
XSAVES/XRSTORS, which is not feasible for performance reasons
- Fix a variety of fuzzing WARNs all caused by checking L1 intercepts
when completing userspace I/O. KVM has already committed to
allowing L2 to to perform I/O at that point
- Emulate PERF_CNTR_GLOBAL_STATUS_SET for PerfMonV2 guests, as the
MSR is supposed to exist for v2 PMUs
- Allow Centaur CPU leaves (base 0xC000_0000) for Zhaoxin CPUs
- Add support for the immediate forms of RDMSR and WRMSRNS, sans full
emulator support (KVM should never need to emulate the MSRs outside
of forced emulation and other contrived testing scenarios)
- Clean up the MSR APIs in preparation for CET and FRED
virtualization, as well as mediated vPMU support
- Clean up a pile of PMU code in anticipation of adding support for
mediated vPMUs
- Reject in-kernel IOAPIC/PIT for TDX VMs, as KVM can't obtain EOI
vmexits needed to faithfully emulate an I/O APIC for such guests
- Many cleanups and minor fixes
- Recover possible NX huge pages within the TDP MMU under read lock
to reduce guest jitter when restoring NX huge pages
- Return -EAGAIN during prefault if userspace concurrently
deletes/moves the relevant memslot, to fix an issue where
prefaulting could deadlock with the memslot update
x86 (AMD):
- Enable AVIC by default for Zen4+ if x2AVIC (and other prereqs) is
supported
- Require a minimum GHCB version of 2 when starting SEV-SNP guests
via KVM_SEV_INIT2 so that invalid GHCB versions result in immediate
errors instead of latent guest failures
- Add support for SEV-SNP's CipherText Hiding, an opt-in feature that
prevents unauthorized CPU accesses from reading the ciphertext of
SNP guest private memory, e.g. to attempt an offline attack. This
feature splits the shared SEV-ES/SEV-SNP ASID space into separate
ranges for SEV-ES and SEV-SNP guests, therefore a new module
parameter is needed to control the number of ASIDs that can be used
for VMs with CipherText Hiding vs. how many can be used to run
SEV-ES guests
- Add support for Secure TSC for SEV-SNP guests, which prevents the
untrusted host from tampering with the guest's TSC frequency, while
still allowing the the VMM to configure the guest's TSC frequency
prior to launch
- Validate the XCR0 provided by the guest (via the GHCB) to avoid
bugs resulting from bogus XCR0 values
- Save an SEV guest's policy if and only if LAUNCH_START fully
succeeds to avoid leaving behind stale state (thankfully not
consumed in KVM)
- Explicitly reject non-positive effective lengths during SNP's
LAUNCH_UPDATE instead of subtly relying on guest_memfd to deal with
them
- Reload the pre-VMRUN TSC_AUX on #VMEXIT for SEV-ES guests, not the
host's desired TSC_AUX, to fix a bug where KVM was keeping a
different vCPU's TSC_AUX in the host MSR until return to userspace
KVM (Intel):
- Preparation for FRED support
- Don't retry in TDX's anti-zero-step mitigation if the target
memslot is invalid, i.e. is being deleted or moved, to fix a
deadlock scenario similar to the aforementioned prefaulting case
- Misc bugfixes and minor cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (142 commits)
KVM: x86: Export KVM-internal symbols for sub-modules only
KVM: x86: Drop pointless exports of kvm_arch_xxx() hooks
KVM: x86: Move kvm_intr_is_single_vcpu() to lapic.c
KVM: Export KVM-internal symbols for sub-modules only
KVM: s390/vfio-ap: Use kvm_is_gpa_in_memslot() instead of open coded equivalent
KVM: VMX: Make CR4.CET a guest owned bit
KVM: selftests: Verify MSRs are (not) in save/restore list when (un)supported
KVM: selftests: Add coverage for KVM-defined registers in MSRs test
KVM: selftests: Add KVM_{G,S}ET_ONE_REG coverage to MSRs test
KVM: selftests: Extend MSRs test to validate vCPUs without supported features
KVM: selftests: Add support for MSR_IA32_{S,U}_CET to MSRs test
KVM: selftests: Add an MSR test to exercise guest/host and read/write
KVM: x86: Define AMD's #HV, #VC, and #SX exception vectors
KVM: x86: Define Control Protection Exception (#CP) vector
KVM: x86: Add human friendly formatting for #XM, and #VE
KVM: SVM: Enable shadow stack virtualization for SVM
KVM: SEV: Synchronize MSR_IA32_XSS from the GHCB when it's valid
KVM: SVM: Pass through shadow stack MSRs as appropriate
KVM: SVM: Update dump_vmcb with shadow stack save area additions
KVM: nSVM: Save/load CET Shadow Stack state to/from vmcb12/vmcb02
...
|
||
|
Linus Torvalds
|
169c9d06a2 |
Merge tag 'linux-watchdog-6.18-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck: - renesas,wdt: Add support for RZ/T2H and RZ/N2H - Add SMARC-sAM67 support - Several small fixes and improvements * tag 'linux-watchdog-6.18-rc1' of git://www.linux-watchdog.org/linux-watchdog: watchdog/hpwdt New maintianer dt-bindings: watchdog: add SMARC-sAM67 support watchdog: mpc8xxx_wdt: Reload the watchdog timer when enabling the watchdog watchdog: visconti: don't print superfluous errors watchdog: rzv2h_wdt: don't print superfluous errors watchdog: rzg2l_wdt: don't print superfluous errors watchdog: s3c2410_wdt: exynosautov9: Enable supported features watchdog: s3c2410_wdt: exynosautov920: Enable QUIRK_HAS_32BIT_CNT watchdog: s3c2410_wdt: Increase max timeout value of watchdog watchdog: s3c2410_wdt: Fix max_timeout being calculated larger watchdog: s3c2410_wdt: Replace hardcoded values with macro definitions watchdog: rzv2h: Improve error strings and add newlines watchdog: rzv2h: Add support for RZ/T2H watchdog: rzv2h: Add support for configurable count clock source watchdog: rzv2h: Make "oscclk" and reset controller optional watchdog: rzv2h: Obtain clock-divider and timeout values from OF match data dt-bindings: watchdog: renesas,wdt: Add support for RZ/T2H and RZ/N2H watchdog: intel_oc_wdt: Do not try to write into const memory |
||
|
Stephen Boyd
|
8397c58ea7 |
Merge branches 'clk-marvell', 'clk-xilinx', 'clk-mediatek' and 'clk-loongson' into clk-next
- Add Mediatek MT8196 clk drivers * clk-marvell: clk: mmp: pxa1908: Instantiate power driver through auxiliary bus * clk-xilinx: clk: clocking-wizard: Fix output clock register offset for Versal platforms clk: xilinx: Optimize divisor search in clk_wzrd_get_divisors_ver() * clk-mediatek: (31 commits) clk: mediatek: Add MT8196 vencsys clock support clk: mediatek: Add MT8196 vdecsys clock support clk: mediatek: Add MT8196 ovl1 clock support clk: mediatek: Add MT8196 ovl0 clock support clk: mediatek: Add MT8196 disp-ao clock support clk: mediatek: Add MT8196 disp1 clock support clk: mediatek: Add MT8196 disp0 clock support clk: mediatek: Add MT8196 mfg clock support clk: mediatek: Add MT8196 mdpsys clock support clk: mediatek: Add MT8196 mcu clock support clk: mediatek: Add MT8196 I2C clock support clk: mediatek: Add MT8196 pextpsys clock support clk: mediatek: Add MT8196 ufssys clock support clk: mediatek: Add MT8196 peripheral clock support clk: mediatek: Add MT8196 vlpckgen clock support clk: mediatek: Add MT8196 topckgen2 clock support clk: mediatek: Add MT8196 topckgen clock support clk: mediatek: Add MT8196 apmixedsys clock support dt-bindings: clock: mediatek: Describe MT8196 clock controllers clk: mediatek: clk-mtk: Add MUX_DIV_GATE macro ... * clk-loongson: clk: loongson2: Add clock definitions for Loongson-2K0300 SoC clk: loongson2: Avoid hardcoding firmware name of the reference clock clk: loongson2: Allow zero divisors for dividers clk: loongson2: Support scale clocks with an alternative mode clk: loongson2: Allow specifying clock flags for gate clock dt-bindings: clock: loongson2: Add Loongson-2K0300 compatible |
||
|
Stephen Boyd
|
b91217d912 |
Merge branches 'clk-microchip', 'clk-lookup' and 'clk-st' into clk-next
- Speed up clk_core_lookup() by using a hashtable * clk-microchip: ARM: at91: remove default values for PMC_PLL_ACR clk: at91: add ACR in all PLL settings clk: at91: sam9x7: Add peripheral clock id for pmecc clk: at91: clk-master: Add check for divide by 3 clk: at91: clk-sam9x60-pll: force write to PLL_UPDT register ARM: at91: pm: save and restore ACR during PLL disable/enable * clk-lookup: clk: Use hashtable for global clk lookups clk: Sort include statements * clk-st: dt-bindings: stm32: cosmetic fixes for STM32MP25 clock and reset bindings clk: stm32: introduce clocks for STM32MP21 platform dt-bindings: stm32: add STM32MP21 clocks and reset bindings |
||
|
Stephen Boyd
|
f0fd248204 |
Merge branches 'clk-scmi', 'clk-qcom' and 'clk-broadcom' into clk-next
* clk-scmi: clk: scmi: Add duty cycle ops only when duty cycle is supported * clk-qcom: (27 commits) clk: qcom: gcc-sc8280xp: drop obsolete PCIe GDSC comment clk: qcom: tcsrcc-x1e80100: Set the bi_tcxo as parent to eDP refclk clk: qcom: dispcc-glymur: Constify 'struct qcom_cc_desc' clk: qcom: gcc: Add support for Global Clock controller found on MSM8937 dt-bindings: clock: qcom: Add MSM8937 Global Clock Controller clk: qcom: Select the intended config in QCS_DISPCC_615 clk: qcom: common: Fix NULL vs IS_ERR() check in qcom_cc_icc_register() clk: qcom: alpha-pll: convert from round_rate() to determine_rate() clk: qcom: milos: Constify 'struct qcom_cc_desc' clk: qcom: gcc: Add support for Global Clock Controller dt-bindings: clock: qcom: document the Glymur Global Clock Controller clk: qcom: clk-alpha-pll: Add support for Taycan EKO_T PLL clk: qcom: rpmh: Add support for Glymur rpmh clocks clk: qcom: Add TCSR clock driver for Glymur SoC dt-bindings: clock: qcom: Document the Glymur SoC TCSR Clock Controller dt-bindings: clock: qcom-rpmhcc: Add support for Glymur SoCs clk: qcom: dispcc-glymur: Add support for Display Clock Controller dt-bindings: clock: Add DISPCC and reset controller for GLYMUR SoC clk: qcom: gcc-sdm660: Add missing LPASS/CDSP vote clocks dt-bindings: clock: gcc-sdm660: Add LPASS/CDSP vote clocks/GDSCs ... * clk-broadcom: clk: bcm: rpi: Maximize V3D clock clk: bcm: rpi: Turn firmware clock on/off when preparing/unpreparing clk: bcm: rpi: Add missing logs if firmware fails |
||
|
Stephen Boyd
|
c1e102f349 |
Merge branches 'clk-imx', 'clk-allwinner' and 'clk-ti' into clk-next
* clk-imx: clk: imx95-blk-ctl: Save/restore registers when RPM routines are called clk: imx95-blk-ctl: Save platform data in imx95_blk_ctl structure * clk-allwinner: clk: sunxi-ng: add support for the A523/T527 MCU CCU clk: sunxi-ng: div: support power-of-two dividers clk: sunxi-ng: sun55i-a523-ccu: Add missing NPU module clock dt-bindings: clock: sun55i-a523-ccu: Add A523 MCU CCU clock controller dt-bindings: clock: sun55i-a523-ccu: Add missing NPU module clock clk: sunxi-ng: sun6i-rtc: Add A523 specifics * clk-ti: clk: keystone: sci-clk: use devm_kmemdup_array() clk: ti: am33xx: keep WKUP_DEBUGSS_CLKCTRL enabled |
||
|
Stephen Boyd
|
3aae991cc2 |
Merge branches 'clk-samsung', 'clk-tegra' and 'clk-amlogic' into clk-next
* clk-samsung: clk: s2mps11: add support for S2MPG10 PMIC clock dt-bindings: clock: samsung,s2mps11: add s2mpg10 clk: samsung: exynos990: Add PERIC0 and PERIC1 clock support dt-bindings: clock: exynos990: Add PERIC0 and PERIC1 clock units clk: samsung: exynos990: Add missing USB clock registers to HSI0 clk: samsung: exynos990: Add LHS_ACEL gate clock for HSI0 and update CLK_NR_TOP dt-bindings: clock: exynos990: Add LHS_ACEL clock ID for HSI0 block clk: samsung: artpec-8: Add initial clock support for ARTPEC-8 SoC clk: samsung: Add clock PLL support for ARTPEC-8 SoC dt-bindings: clock: Add ARTPEC-8 clock controller clk: samsung: exynos990: Add DPU_BUS and CMUREF mux/div and update CLKS_NR_TOP dt-bindings: clock: exynos990: Extend clocks IDs clk: samsung: exynos990: Replace bogus divs with fixed-factor clocks clk: samsung: exynos990: Fix CMU_TOP mux/div bit widths clk: samsung: exynos990: Use PLL_CON0 for PLL parent muxes clk: samsung: pll: convert from round_rate() to determine_rate() clk: samsung: cpu: convert from round_rate() to determine_rate() clk: samsung: fsd: Add clk id for PCLK and PLL in CAM_CSI block dt-bindings: clock: Add CAM_CSI clock macro for FSD * clk-tegra: clk: tegra: dfll: Add CVB tables for Tegra114 clk: tegra: Add DFLL DVCO reset control for Tegra114 dt-bindings: arm: tegra: Add ASUS TF101G and SL101 dt-bindings: reset: Add Tegra114 CAR header dt-bindings: arm: tegra: Add Xiaomi Mi Pad (A0101) dt-bindings: clock: tegra30: Add IDs for CSI pad clocks dt-bindings: display: tegra: Move avdd-dsi-csi-supply from VI to CSI dt-bindings: i2c: nvidia,tegra20-i2c: Document Tegra264 I2C * clk-amlogic: clk: amlogic: fix recent code refactoring clk: amlogic: c3-peripherals: use helper for basic composite clocks clk: amlogic: align s4 and c3 pwm clock descriptions clk: amlogic: add composite clock helpers clk: amlogic: use the common pclk definition clk: amlogic: introduce a common pclk definition clk: amlogic: pclk explicitly use CLK_IGNORE_UNUSED clk: amlogic: drop CLK_SET_RATE_PARENT from peripheral clocks clk: amlogic: move PCLK definition to clkc-utils clk: amlogic: aoclk: use clkc-utils syscon probe clk: amlogic: use probe helper in mmio based controllers clk: amlogic: add probe helper for mmio based controllers clk: amlogic: drop meson-clkcee clk: amlogic: naming consistency alignment |
||
|
Stephen Boyd
|
ec7336475d |
Merge branches 'clk-bindings', 'clk-cleanup', 'clk-renesas', 'clk-thead' and 'clk-spacemit' into clk-next
* clk-bindings: dt-bindings: clock: mediatek: Add power-domains property dt-bindings: clock: silabs,si5341: Add missing properties dt-bindings: clock: adi,axi-clkgen: add clock-output-names property dt-bindings: clock: Remove unused fujitsu,mb86s70-crg11 binding dt-bindings: clock: Convert silabs,si570 to DT schema dt-bindings: clock: Convert silabs,si5341 to DT schema dt-bindings: clock: Convert silabs,si514/544 to DT schema * clk-cleanup: clk: tegra: do not overallocate memory for bpmp clocks clk: ep93xx: Use int type to store negative error codes dt-bindings: clock: st: flexgen: remove deprecated compatibles clk: st: flexgen: remove unused compatible clk: clk-axi-clkgen: remove unneeded semicolon clk: tegra: Remove redundant semicolons clk: npcm: select CONFIG_AUXILIARY_BUS clk: remove unneeded 'fast_io' parameter in regmap_config * clk-renesas: (27 commits) clk: renesas: r9a09g05[67]: Reduce differences clk: renesas: r9a09g047: Add USB3.0 clocks/resets clk: renesas: cpg-mssr: Fix memory leak in cpg_mssr_reserved_init() clk: renesas: r9a09g056: Add clock and reset entries for I3C clk: renesas: r9a09g057: Add clock and reset entries for I3C dt-bindings: clock: renesas,r9a09g047-cpg: Add USB3.0 core clocks clk: renesas: r9a09g077: Add Ethernet Subsystem core and module clocks clk: renesas: rzv2h: Simplify polling condition in __rzv2h_cpg_assert() clk: renesas: rzv2h: Re-assert reset on deassert timeout clk: renesas: rzg2l: Re-assert reset on deassert timeout clk: renesas: rzg2l: Simplify rzg2l_cpg_assert() and rzg2l_cpg_deassert() dt-bindings: clock: renesas,r9a09g077/87: Add Ethernet clock IDs clk: renesas: r9a09g047: Add GPT clocks and resets clk: renesas: r9a09g077: Add module clocks for SCI1-SCI5 clk: renesas: rzv2h: remove round_rate() in favor of determine_rate() clk: renesas: rzg2l: convert from round_rate() to determine_rate() clk: renesas: r9a07g04[34]: Use tabs instead of spaces clk: renesas: r9a07g043: Add MSTOP for RZ/G2UL clk: renesas: r9a07g044: Add MSTOP for RZ/G2L clk: renesas: r9a08g045: Add MSTOP for GPIO ... * clk-thead: clk: thead: th1520-ap: set all AXI clocks to CLK_IS_CRITICAL clk: thead: support changing DPU pixel clock rate clk: thead: add support for enabling/disabling PLLs clk: thead: Correct parent for DPU pixel clocks clk: thead: th1520-ap: fix parent of padctrl0 clock clk: thead: th1520-ap: describe gate clocks with clk_gate * clk-spacemit: clk: spacemit: fix i2s clock clk: spacemit: introduce pre-div for ddn clock dt-bindings: clock: spacemit: introduce i2s pre-clock to fix i2s clock clk: spacemit: ccu_pll: convert from round_rate() to determine_rate() clk: spacemit: ccu_mix: convert from round_rate() to determine_rate() clk: spacemit: ccu_ddn: convert from round_rate() to determine_rate() clk: spacemit: fix sspax_clk dt-bindings: clock: spacemit: CLK_SSPA_I2S_BCLK for SSPA |
||
|
Linus Torvalds
|
2f2c725493 |
Merge tag 'pci-v6.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Add PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() macros that
take config space accessor functions.
Implement pci_find_capability(), pci_find_ext_capability(), and
dwc, dwc endpoint, and cadence capability search interfaces with
them (Hans Zhang)
- Leave parent unit address 0 in 'interrupt-map' so that when we
build devicetree nodes to describe PCI functions that contain
multiple peripherals, we can build this property even when
interrupt controllers lack 'reg' properties (Lorenzo Pieralisi)
- Add a Xeon 6 quirk to disable Extended Tags and limit Max Read
Request Size to 128B to avoid a performance issue (Ilpo Järvinen)
- Add sysfs 'serial_number' file to expose the Device Serial Number
(Matthew Wood)
- Fix pci_acpi_preserve_config() memory leak (Nirmoy Das)
Resource management:
- Align m68k pcibios_enable_device() with other arches (Ilpo
Järvinen)
- Remove sparc pcibios_enable_device() implementations that don't do
anything beyond what pci_enable_resources() does (Ilpo Järvinen)
- Remove mips pcibios_enable_resources() and use
pci_enable_resources() instead (Ilpo Järvinen)
- Clean up bridge window sizing and assignment (Ilpo Järvinen),
including:
- Leave non-claimed bridge windows disabled
- Enable bridges even if a window wasn't assigned because not all
windows are required by downstream devices
- Preserve bridge window type when releasing the resource, since
the type is needed for reassignment
- Consolidate selection of bridge windows into two new
interfaces, pbus_select_window() and
pbus_select_window_for_type(), so this is done consistently
- Compute bridge window start and end earlier to avoid logging
stale information
MSI:
- Add quirk to disable MSI on RDC PCI to PCIe bridges (Marcos Del Sol
Vives)
Error handling:
- Align AER with EEH by allowing drivers to request a Bus Reset on
Non-Fatal Errors (in addition to the reset on Fatal Errors that we
already do) (Lukas Wunner)
- If error recovery fails, emit FAILED_RECOVERY uevents for the
devices, not for the bridge leading to them.
This makes them correspond to BEGIN_RECOVERY uevents (Lukas Wunner)
- Align AER with EEH by calling err_handler.error_detected()
callbacks to notify drivers if error recovery fails (Lukas Wunner)
- Align AER with EEH by restoring device error_state to
pci_channel_io_normal before the err_handler.slot_reset() callback.
This is earlier than before the err_handler.resume() callback
(Lukas Wunner)
- Emit a BEGIN_RECOVERY uevent when driver's
err_handler.error_detected() requests a reset, as well as when it
says recovery is complete or can be done without a reset (Niklas
Schnelle)
- Align s390 with AER and EEH by emitting uevents during error
recovery (Niklas Schnelle)
- Align EEH with AER and s390 by emitting BEGIN_RECOVERY,
SUCCESSFUL_RECOVERY, or FAILED_RECOVERY uevents depending on the
result of err_handler.error_detected() (Niklas Schnelle)
- Fix a NULL pointer dereference in aer_ratelimit() when ACPI GHES
error information identifies a device without an AER Capability
(Breno Leitao)
- Update error decoding and TLP Log printing for new errors in
current PCIe base spec (Lukas Wunner)
- Update error recovery documentation to match the current code
and use consistent nomenclature (Lukas Wunner)
ASPM:
- Enable all ClockPM and ASPM states for devicetree platforms, since
there's typically no firmware that enables ASPM
This is a risky change that may uncover hardware or configuration
defects at boot-time rather than when users enable ASPM via sysfs
later. Booting with "pcie_aspm=off" prevents this enabling
(Manivannan Sadhasivam)
- Remove the qcom code that enabled ASPM (Manivannan Sadhasivam)
Power management:
- If a device has already been disconnected, e.g., by a hotplug
removal, don't bother trying to resume it to D0 when detaching the
driver.
This avoids annoying "Unable to change power state from D3cold to
D0" messages (Mario Limonciello)
- Ensure devices are powered up before config reads for
'max_link_width', 'current_link_speed', 'current_link_width',
'secondary_bus_number', and 'subordinate_bus_number' sysfs files.
This prevents using invalid data (~0) in drivers or lspci and,
depending on how the PCIe controller reports errors, may avoid
error interrupts or crashes (Brian Norris)
Virtualization:
- Add rescan/remove locking when enabling/disabling SR-IOV, which
avoids list corruption on s390, where disabling SR-IOV also
generates hotplug events (Niklas Schnelle)
Peer-to-peer DMA:
- Free struct p2p_pgmap, not a member within it, in the
pci_p2pdma_add_resource() error path (Sungho Kim)
Endpoint framework:
- Document sysfs interface for BAR assignment of vNTB endpoint
functions (Jerome Brunet)
- Fix array underflow in endpoint BAR test case (Dan Carpenter)
- Skip endpoint IRQ test if the IRQ is out of range to avoid false
errors (Christian Bruel)
- Fix endpoint test case for controllers with fixed-size BARs smaller
than requested by the test (Marek Vasut)
- Restore inbound translation when disabling doorbell so the endpoint
doorbell test case can be run more than once (Niklas Cassel)
- Avoid a NULL pointer dereference when releasing DMA channels in
endpoint DMA test case (Shin'ichiro Kawasaki)
- Convert tegra194 interrupt number to MSI vector to fix endpoint
Kselftest MSI_TEST test case (Niklas Cassel)
- Reset tegra194 BARs when running in endpoint mode so the BAR tests
don't overwrite the ATU settings in BAR4 (Niklas Cassel)
- Handle errors in tegra194 BPMP transactions so we don't mistakenly
skip future PERST# assertion (Vidya Sagar)
AMD MDB PCIe controller driver:
- Update DT binding example to separate PERST# to a Root Port stanza
to make multiple Root Ports possible in the future (Sai Krishna
Musham)
- Add driver support for PERST# being described in a Root Port
stanza, falling back to the host bridge if not found there (Sai
Krishna Musham)
Freescale i.MX6 PCIe controller driver:
- Enable the 3.3V Vaux supply if available so devices can request
wakeup with either Beacon or WAKE# (Richard Zhu)
MediaTek PCIe Gen3 controller driver:
- Add optional sys clock ready time setting to avoid sys_clk_rdy
signal glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196
(AngeloGioacchino Del Regno)
NVIDIA Tegra PCIe controller driver:
- When asserting PERST#, disable the controller instead of mistakenly
disabling the PLL twice (Nagarjuna Kristam)
- Convert struct tegra_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
Qualcomm PCIe controller driver:
- Select PCI Power Control Slot driver so slot voltage rails can be
turned on/off if described in Root Port devicetree node (Qiang Yu)
- Parse only PCI bridge child nodes in devicetree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused
probe failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root
Port node or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than
in each driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG
Shift Feature' and use this in the qcom driver (Krishna Chaitanya
Chundru)
- Add SM8750 compatible to qcom,pcie-sm8550.yaml (Krishna Chaitanya
Chundru)
- Update qcom,pcie-x1e80100.yaml to allow fifth PCIe host on Qualcomm
Glymur, which is compatible with X1E80100 but doesn't have the
cnoc_sf_axi clock (Qiang Yu)
Renesas R-Car PCIe controller driver:
- Fix a typo that prevented correct PHY initialization (Marek Vasut)
- Add a missing 1ms delay after PWR reset assertion as required by
the V4H manual (Marek Vasut)
- Assure reset has completed before DBI access to avoid SError (Marek
Vasut)
- Fix inverted PHY initialization check, which sometimes led to
timeouts and failure to start the controller (Marek Vasut)
- Pass the correct IRQ domain to generic_handle_domain_irq() to fix a
regression when converting to msi_create_parent_irq_domain()
(Claudiu Beznea)
- Drop the spinlock protecting the PMSR register - it's no longer
required since pci_lock already serializes accesses (Marek Vasut)
- Convert struct rcar_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
SOPHGO PCIe controller driver:
- Check for existence of struct cdns_pcie.ops before using it to
allow Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the SOPHGO SG2042 PCIe controller
(Chen Wang)
STMicroelectronics STM32MP25 PCIe controller driver:
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which
needs it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics
STM32MP25 in host and endpoint modes (Christian Bruel)
Synopsys DesignWare PCIe controller driver:
- Add support for x16 in devicetree 'num-lanes' property (Konrad
Dybcio)
- Verify that if DT specifies a single IRQ for all eDMA channels, it
is named 'dma' (Niklas Cassel)
TI J721E PCIe driver:
- Add MODULE_DEVICE_TABLE() so driver can be autoloaded (Siddharth
Vadapalli)
- Power controller off before configuring the glue layer so the
controller latches the correct values on power-on (Siddharth
Vadapalli)
TI Keystone PCIe controller driver:
- Use devm_request_irq() so 'ks-pcie-error-irq' is freed when driver
exits with error (Siddharth Vadapalli)
- Add Peripheral Virtualization Unit (PVU), which restricts DMA from
PCIe devices to specific regions of host memory, to the ti,am65
binding (Jan Kiszka)
Xilinx NWL PCIe controller driver:
- Clear bootloader E_ECAM_CONTROL before merging in the new driver
value to avoid writing invalid values (Jani Nurminen)"
* tag 'pci-v6.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (141 commits)
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
PCI: xilinx-nwl: Fix ECAM programming
PCI: j721e: Fix incorrect error message in probe()
PCI: keystone: Use devm_request_irq() to free "ks-pcie-error-irq" on exit
dt-bindings: PCI: qcom,pcie-x1e80100: Set clocks minItems for the fifth Glymur PCIe Controller
PCI: dwc: Support 16-lane operation
PCI: Add lockdep assertion in pci_stop_and_remove_bus_device()
PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV
PCI: rcar-host: Convert struct rcar_msi mask_lock into raw spinlock
PCI: tegra194: Rename 'root_bus' to 'root_port_bus' in tegra_pcie_downstream_dev_to_D0()
PCI: tegra: Convert struct tegra_msi mask_lock into raw spinlock
PCI: rcar-gen4: Fix inverted break condition in PHY initialization
PCI: rcar-gen4: Assure reset occurs before DBI access
PCI: rcar-gen4: Add missing 1ms delay after PWR reset assertion
PCI: Set up bridge resources earlier
PCI: rcar-host: Drop PMSR spinlock
...
|
||
|
Linus Torvalds
|
e4c0fdd5af |
Merge tag 'dmaengine-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul: "A couple of new device support and small driver updates for this round. New support: - Intel idxd Wildcat Lake family support - SpacemiT K1 PDMA controller support - Renesas RZ/G3E family support Updates: - Xilinx shutdown support and dma client properties update - Designware edma callback_result support" * tag 'dmaengine-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: dt-bindings: dma: rz-dmac: Document RZ/G3E family of SoCs dmaengine: dw-edma: Set status for callback_result dmaengine: mv_xor: match alloc_wc and free_wc dmaengine: mmp_pdma: Add SpacemiT K1 PDMA support with 64-bit addressing dmaengine: mmp_pdma: Add operations structure for controller abstraction dmaengine: mmp_pdma: Add reset controller support dmaengine: mmp_pdma: Add clock support dt-bindings: dma: Add SpacemiT K1 PDMA controller dt-bindings: dmaengine: xilinx_dma: Remove DMA client properties dmaengine: Fix dma_async_tx_descriptor->tx_submit documentation dmaengine: xilinx_dma: Support descriptor setup from dma_vecs dmaengine: sh: setup_xref error handling dmaengine: Replace zero-length array with flexible-array dmaengine: ppc4xx: Remove space before newline dmaengine: idxd: Add a new IAA device ID for Wildcat Lake family platforms dmaengine: idxd: Replace memset(0) + strscpy() with strscpy_pad() dt-bindings: dma: nvidia,tegra20-apbdma: Add undocumented compatibles and "clock-names" dmaengine: zynqmp_dma: Add shutdown operation support |
||
|
Linus Torvalds
|
1d1ba4d390 |
Merge tag 'phy-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"The usual bunch of device support and update to drivers.
New Support
- Qualcomm SM8750 QMP PCIe PHY dual lane support, PMIV0104 eusb2
repeater support, QCS8300 eDP PHY support
- Renesas RZ/T2H and RZ/N2H support and updates to driver for that
- TI TCAN1051 phy support
- Rockchip rk3588 dphy support, RK3528 combphy support
Updates:
- cadence updates for calibration and polling for ready and enabling
of lower resolutions, runtime pm support,
- Rockchip: enable U3 otg port
- Renesas USXGMII mode support
- Qualcomm UFS PHY and PLL regulator load support"
* tag 'phy-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (64 commits)
phy: rockchip: phy-rockchip-inno-csidphy: add support for rk3588 variant
phy: rockchip: phy-rockchip-inno-csidphy: allow for different reset lines
phy: rockchip: phy-rockchip-inno-csidphy: allow writes to grf register 0
dt-bindings: phy: rockchip-inno-csi-dphy: add rk3588 variant
dt-bindings: phy: rockchip-inno-csi-dphy: make power-domains non-required
phy: cadence: cdns-dphy: Enable lower resolutions in dphy
phy: renesas: r8a779f0-ether-serdes: add new step added to latest datasheet
phy: renesas: r8a779f0-ether-serdes: add USXGMII mode
phy: sophgo: Add USB 2.0 PHY driver for Sophgo CV18XX/SG200X
dt-bindings: phy: Add Sophgo CV1800 USB phy
phy: cadence: cdns-dphy: Update calibration wait time for startup state machine
phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling
phy: renesas: rcar-gen3-usb2: Fix ID check logic with VBUS valid
dt-bindings: phy: ti,tcan104x-can: Document TI TCAN1051
phy: lynx-28g: check return value when calling lynx_28g_pll_get
phy: qcom: m31-eusb2: Fix the error log while enabling clock
phy: rockchip: usbdp: Remove redundant ternary operators
phy: renesas: rcar-gen3-usb2: Remove redundant ternary operators
phy: hisilicon: Remove redundant ternary operators
phy: qcom-qmp-ufs: Add PHY and PLL regulator load
...
|
||
|
Cédric Le Goater
|
451bb96328 |
vfio: Dump migration features under debugfs
A debugfs directory was recently added for VFIO devices. Add a new "features" file under the migration sub-directory to expose which features the device supports. Signed-off-by: Cédric Le Goater <clg@redhat.com> Link: https://lore.kernel.org/r/20250918121928.1921871-1-clg@redhat.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> |
||
|
Linus Torvalds
|
4b616669d1 |
Merge tag 'ata-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Damien Le Moal: - Improve the DT bindings documentation for the highbanck, imx and xgene-ahci controllers (Krzysztof, Fabio, Rob) * tag 'ata-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux: dt-bindings: ata: apm,xgene-ahci: Add apm,xgene-ahci-v2 support dt-bindings: ata: imx: Document 'target-supply' dt-bindings: ata: highbank: Minor whitespace cleanup in example |
||
|
Linus Torvalds
|
7a405dbb0f |
Merge tag 'mm-stable-2025-10-03-16-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more MM updates from Andrew Morton:
"Only two patch series in this pull request:
- "mm/memory_hotplug: fixup crash during uevent handling" from Hannes
Reinecke fixes a race that was causing udev to trigger a crash in
the memory hotplug code
- "mm_slot: following fixup for usage of mm_slot_entry()" from Wei
Yang adds some touchups to the just-merged mm_slot changes"
* tag 'mm-stable-2025-10-03-16-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/khugepaged: use KMEM_CACHE()
mm/ksm: cleanup mm_slot_entry() invocation
Documentation/mm: drop pxx_mkdevmap() descriptions from page table helpers
mm: clean up is_guard_pte_marker()
drivers/base: move memory_block_add_nid() into the caller
mm/memory_hotplug: activate node before adding new memory blocks
drivers/base/memory: add node id parameter to add_memory_block()
|
||
|
Rob Herring (Arm)
|
a6b4f791cd |
dt-bindings: rtc: Convert apm,xgene-rtc to DT schema
Convert the APM XGene RTC binding to DT schema format. It's a straight-forward conversion. Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Link: https://lore.kernel.org/r/20250924222848.2949235-1-robh@kernel.org Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> |
||
|
Linus Torvalds
|
6a74422b97 |
Merge tag 'mips_6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer: - switch longson32 platform to DT and use MIPS_GENERIC framework - cleanups/fixes for lantiq DTs - other cleanups and fixes * tag 'mips_6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (30 commits) mips: math-emu: replace deprecated strcpy() in me-debugfs MIPS: configs: Consolidate Loongson1 defconfigs MIPS: Unify Loongson1 PRID_REV MIPS: loongson32: Switch to generic core MIPS: loongson: Add built-in DTB support MIPS: dts: loongson: Add CQ-T300B board MIPS: dts: loongson: Add Smartloong-1C board MIPS: dts: loongson: Add LSGZ_1B_DEV board MIPS: dts: loongson: Add LS1B-DEMO board dt-bindings: mips: loongson: Add LS1B-DEMO and CQ-T300B mips: lantiq: danube: rename stp node on EASY50712 reference board mips: lantiq: xway: sysctrl: rename stp clock MIPS: RB532: Replace deprecated strcpy() with memcpy() and strscpy() MIPS: Loongson64: Replace deprecated strcpy() with strscpy_pad() MIPS: generic: Replace deprecated strcpy() in ocelot_detect() MIPS: octeon: Replace deprecated strcpy() in octeon_model_get_string_buffer() MIPS: octeon: Replace memset(0) + deprecated strcpy() with strscpy_pad() MIPS: arc: Replace deprecated strcpy() with memcpy() MIPS: txx9: Replace deprecated strcpy() with strscpy() MIPS: sni: Replace deprecated strcpy() in sni_console_setup() ... |
||
|
Linus Torvalds
|
742adaa16d |
Merge tag 'for-linus' of https://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne: "I picked up one series from Chen Miao, our Google Summer of Code contributor, which adds OpenRISC support for static keys" * tag 'for-linus' of https://github.com/openrisc/linux: openrisc: Add jump label support openrisc: Regenerate defconfigs. openrisc: Add R_OR1K_32_PCREL relocation type module support openrisc: Add text patching API support |
||
|
Linus Torvalds
|
d9f24f8e60 |
Merge tag 'trace-tools-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing tools updates from Steven Rostedt - This is mostly just consolidating code between osnoise/timerlat and top/hist for easier maintenance and less future divergence * tag 'trace-tools-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: tools/rtla: Add remaining support for osnoise actions tools/rtla: Add test engine support for unexpected output tools/rtla: Fix -A option name in test comment tools/rtla: Consolidate code between osnoise/timerlat and hist/top tools/rtla: Create common_apply_config() tools/rtla: Move top/hist params into common struct tools/rtla: Consolidate common parameters into shared structure |
||
|
Linus Torvalds
|
6093a688a0 |
Merge tag 'char-misc-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc/IIO/Binder updates from Greg KH:
"Here is the big set of char/misc/iio and other driver subsystem
changes for 6.18-rc1.
Loads of different stuff in here, it was a busy development cycle in
lots of different subsystems, with over 27k new lines added to the
tree.
Included in here are:
- IIO updates including new drivers, reworking of existing apis, and
other goodness in the sensor subsystems
- MEI driver updates and additions
- NVMEM driver updates
- slimbus removal for an unused driver and some other minor updates
- coresight driver updates and additions
- MHI driver updates
- comedi driver updates and fixes
- extcon driver updates
- interconnect driver additions
- eeprom driver updates and fixes
- minor UIO driver updates
- tiny W1 driver updates
But the majority of new code is in the rust bindings and additions,
which includes:
- misc driver rust binding updates for read/write support, we can now
write "normal" misc drivers in rust fully, and the sample driver
shows how this can be done.
- Initial framework for USB driver rust bindings, which are disabled
for now in the build, due to limited support, but coming in through
this tree due to dependencies on other rust binding changes that
were in here. I'll be enabling these back on in the build in the
usb.git tree after -rc1 is out so that developers can continue to
work on these in linux-next over the next development cycle.
- Android Binder driver implemented in Rust.
This is the big one, and was driving a huge majority of the rust
binding work over the past years. Right now there are two binder
drivers in the kernel, selected only at build time as to which one
to use as binder wants to be included in the system at boot time.
The binder C maintainers all agreed on this, as eventually, they
want the C code to be removed from the tree, but it will take a few
releases to get there while both are maintained to ensure that the
rust implementation is fully stable and compliant with the existing
userspace apis.
All of these have been in linux-next for a while"
* tag 'char-misc-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (320 commits)
rust: usb: keep usb::Device private for now
rust: usb: don't retain device context for the interface parent
USB: disable rust bindings from the build for now
samples: rust: add a USB driver sample
rust: usb: add basic USB abstractions
coresight: Add label sysfs node support
dt-bindings: arm: Add label in the coresight components
coresight: tnoc: add new AMBA ID to support Trace Noc V2
coresight: Fix incorrect handling for return value of devm_kzalloc
coresight: tpda: fix the logic to setup the element size
coresight: trbe: Return NULL pointer for allocation failures
coresight: Refactor runtime PM
coresight: Make clock sequence consistent
coresight: Refactor driver data allocation
coresight: Consolidate clock enabling
coresight: Avoid enable programming clock duplicately
coresight: Appropriately disable trace bus clocks
coresight: Appropriately disable programming clocks
coresight: etm4x: Support atclk
coresight: catu: Support atclk
...
|
||
|
Linus Torvalds
|
c6006b8ca1 |
Merge tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It
was another normal development cycle, with lots of the usual drivers
getting updates:
- Thunderbolt driver cleanups and additions
- dwc3 driver updates
- dwc2 driver updates
- typec driver updates
- xhci driver updates and additions
- offload USB engine updates for better power management
- unused tracepoint removals
- usb gadget fixes and updates as more users start to rely on these
drivers instead of the "old" function gadget drivers
- new USB device ids
- other minor driver USB driver updates
- new USB I/O driver framework and driver additions"
The last item, the usb i/o driver, has an i2c and gpio driver added
through this tree. Those drivers were acked by the respective
subsystem maintainers.
All of these have been in linux-next for a while"
* tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (132 commits)
usb: vhci-hcd: Prevent suspending virtually attached devices
USB: serial: option: add SIMCom 8230C compositions
thunderbolt: Fix use-after-free in tb_dp_dprx_work
usb: xhci: align PORTSC trace with one-based port numbering
usb: xhci: correct indentation for PORTSC tracing function
usb: xhci: improve TR Dequeue Pointer mask
usb: xhci-pci: add support for hosts with zero USB3 ports
usb: xhci: Update a comment about Stop Endpoint retries
Revert "usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running"
usb: gadget: f_rndis: Refactor bind path to use __free()
usb: gadget: f_ecm: Refactor bind path to use __free()
usb: gadget: f_acm: Refactor bind path to use __free()
usb: gadget: f_ncm: Refactor bind path to use __free()
usb: gadget: Introduce free_usb_request helper
usb: gadget: Store endpoint pointer in usb_request
usb: host: xhci-rcar: Add Renesas RZ/G3E USB3 Host driver support
usb: host: xhci-plat: Add .post_resume_quirk for struct xhci_plat_priv
usb: host: xhci-rcar: Move R-Car reg definitions
dt-bindings: usb: Document Renesas RZ/G3E USB3HOST
usb: gadget: f_fs: Fix epfile null pointer access after ep enable.
...
|
||
|
Linus Torvalds
|
5d2f4730bb |
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (43 commits)
tty: serial: fix help message for SERIAL_CPM
serial: 8250: omap: Support wakeup pinctrl state on suspend
dt-bindings: serial: 8250_omap: Add wakeup pinctrl state
serial: max310x: improve interrupt handling
vt: move vc_saved_screen to within tty allocated judgment
Revert "m68k: make HPDCA and HPAPCI bools"
tty: remove redundant condition checks
tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()
vt: remove redundant check on vc_mode in con_font_set()
serial: qcom-geni: Add DFS clock mode support to GENI UART driver
m68k: make HPDCA and HPAPCI bools
tty: n_gsm: Don't block input queue by waiting MSC
serial: qcom-geni: Fix off-by-one error in ida_alloc_range()
serdev: Drop dev_pm_domain_detach() call
serial: sc16is7xx: drop redundant conversion to bool
vt: add support for smput/rmput escape codes
serial: stm32: allow selecting console when the driver is module
serial: 8250_core: fix coding style issue
tty: serial: Modify the use of dev_err_probe()
s390/char/con3270: use tty_port_tty guard()
...
|
||
|
Linus Torvalds
|
cc07b0a3af |
Merge tag 'mtd/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core:
- Bad blocks increment is skipped if the block is already known bad
(improves user statistics relevance)
- Expose the OOB layout via debugfs
Raw NAND:
- Add support for Loongson-2K1000 and Loongson-2K0500 NAND
controllers, including extra features, such as chip select
and 6-byte NAND ID reading support
- Drop the s3c2410 driver
SPI NAND:
- Important SPI NAND continuous read improvements and fixes
- Add support for FudanMicro FM25S01A
- Add support for continuous reads in Gigadevice vendor driver
ECC:
- Add support for the Realtek ECC engine
SPI NOR:
- Some flashes can't perform reads or writes with start or end being
an odd number in Octal DTR mode. File systems like UBIFS can
request such reads or writes, causing the transaction to error out.
Pad the read or write transactions with extra bytes to avoid this
problem.
And the usual amount of various miscellaneous fixes"
* tag 'mtd/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (46 commits)
mtd: rawnand: sunxi: drop unused module alias
mtd: rawnand: stm32_fmc2: drop unused module alias
mtd: rawnand: rockchip: drop unused module alias
mtd: rawnand: pl353: drop unused module alias
mtd: rawnand: omap2: drop unused module alias
mtd: rawnand: atmel: drop unused module alias
mtd: onenand: omap2: drop unused module alias
mtd: hyperbus: hbmc-am654: drop unused module alias
mtd: jedec_probe: use struct_size() helper for cfiq allocation
mtd: cfi: use struct_size() helper for cfiq allocation
mtd: nand: raw: gpmi: fix clocks when CONFIG_PM=N
mtd: rawnand: omap2: fix device leak on probe failure
mtd: rawnand: atmel: Fix error handling path in atmel_nand_controller_add_nands
mtd: nand: realtek-ecc: Add Realtek external ECC engine support
dt-bindings: mtd: Add realtek,rtl9301-ecc
mtd: spinand: repeat reading in regular mode if continuous reading fails
mtd: spinand: try a regular dirmap if creating a dirmap for continuous reading fails
mtd: spinand: fix direct mapping creation sizes
mtd: rawnand: fsmc: Default to autodetect buswidth
mtd: nand: move nand_check_erased_ecc_chunk() to nand/core
...
|
||
|
Linus Torvalds
|
c35f902cb3 |
Merge tag 'rproc-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson: - Enable coredump support for the i.MX HiFi core remoteproc, and clean up the i.MX remoteproc driver. - Introduce remoteprocs on the Qualcomm Milos platform. Gracefully shut own the ADSP remoteproc when bootloader has loaded the "Lite" firmware on X Elite. Improve the resource handover procedure to avoid possibly duplicate handling. - Transition the TI DA8xx, TI Keystone, and TI Wakeup M3 remoteproc drivers to handle resources using devres. * tag 'rproc-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (29 commits) remoteproc: pru: Fix potential NULL pointer dereference in pru_rproc_set_ctable() remoteproc: qcom: pas: Drop redundant assignment to ret remoteproc: qcom: pas: Shutdown lite ADSP DTB on X1E remoteproc: qcom: q6v5: Avoid handling handover twice remoteproc: qcom: q6v5: Avoid disabling handover IRQ twice remoteproc: qcom: pas: Add Milos remoteproc support dt-bindings: remoteproc: qcom,milos-pas: Document remoteprocs remoteproc: qcom_q6v5_mss: support loading MBN file on msm8974 remoteproc: imx_rproc: Clean up after ops introduction remoteproc: imx_rproc: Simplify IMX_RPROC_SMC switch case remoteproc: imx_rproc: Simplify IMX_RPROC_SCU_API switch case remoteproc: imx_rproc: Simplify IMX_RPROC_MMIO switch case remoteproc: imx_rproc: Move imx_rproc_dcfg closer to imx_rproc_of_match remoteproc: imx_rproc: Introduce start/stop/detect_mode ops for imx_rproc_dcfg remoteproc: k3: Correctly release some resources allocated in k3_rproc_request_mbox() remoteproc: wkup_m3: Use devm_rproc_add() helper remoteproc: wkup_m3: Use devm_rproc_alloc() helper remoteproc: wkup_m3: Use devm action to call PM runtime put sync remoteproc: wkup_m3: Use devm_pm_runtime_enable() helper remoteproc: keystone: Use devm_rproc_add() helper ... |
||
|
Linus Torvalds
|
54ba6d9b13 |
Merge tag 'hid-for-linus-2025093001' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- haptic touchpad support (Angela Czubak and Jonathan Denose)
- support for audio jack handling on DualSense Playstation controllers
(Cristian Ciocaltea)
- allow HID-BPF to rebind a driver to hid-multitouch (Benjamin
Tissoires)
- rework hidraw ioctls to make them safer (and tested) (Benjamin
Tissoires)
- various PIDFF and universal-PIDFF fixes/improvements (Tomasz Pakuła)
- better configuration of Intel QuickI2C through ACPI (Xinpeng Sun)
- other assorted cleanups and fixes
* tag 'hid-for-linus-2025093001' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (58 commits)
HID: playstation: Switch to scoped_guard() in {dualsense|dualshock4}_output_worker()
HID: playstation: Silence sparse warnings for locking context imbalances
HID: playstation: Update SP preamp gain comment line
HID: intel-thc-hid: intel-quicki2c: support ACPI config for advanced features
HID: core: Change hid_driver to use a const char* for name
HID: hidraw: tighten ioctl command parsing
selftests/hid: hidraw: forge wrong ioctls and tests them
selftests/hid: hidraw: add more coverage for hidraw ioctls
selftests/hid: update vmtest.sh for virtme-ng
HID: playstation: Support DualSense audio jack event reporting
HID: playstation: Support DualSense audio jack hotplug detection
HID: playstation: Redefine DualSense input report status field
HID: playstation: Prefer kzalloc(sizeof(*buf)...)
HID: playstation: Document spinlock_t usage
HID: playstation: Fix all alignment and line length issues
HID: playstation: Correct spelling in comment sections
HID: playstation: Replace uint{32,16,8}_t with u{32,16,8}
HID: playstation: Simplify locking with guard() and scoped_guard()
HID: playstation: Add spaces around arithmetic operators
HID: playstation: Make use of bitfield macros
...
|
||
|
Linus Torvalds
|
b66451723c |
Merge tag 'platform-drivers-x86-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Ilpo Järvinen:
- amd/pmf:
- Add support for adjusting PMF PPT and PPT APU thresholds
- Extend custom BIOS inputs for more policies
- Update ta_pmf_action structure to the latest PMF TA
- arm64:
- thinkpad-t14s-ec: Add EC driver for ThinkPad T14s Gen6 Snapdragon
- int3472:
- Increase handshake GPIO delay
- intel/pmc:
- SSRAM support for Lunar Lake and Panther Lake
- Support reading substate requirements data from S0ix blockers
(for platforms starting from Panther Lake)
- Wildcat Lake support
- intel-uncore-freq:
- Solve duplicate sysfs entry warnings
- Present unique domain ID per package
- portwell-ec:
- Support suspend/resume
- Add hwmon support for voltage and temperature
- redmi-wmi:
- Add WMI driver for Redmibook keyboard
- think-lmi:
- Certificate support for ThinkCenter
- x86-android-tables + others:
- Convert away from legacy GPIO APIs
- x86-android-tables:
- Add support for Acer A1-840 tablet
- Fix modules list for Lenovo devices
- Stop using EPROBE_DEFER
- Miscellaneous cleanups / refactoring / improvements
* tag 'platform-drivers-x86-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (63 commits)
platform/x86: pcengines-apuv2: Use static device properties
platform/x86: meraki-mx100: Use static device properties
platform/x86: barco-p50-gpio: use software nodes for gpio-leds/keys
platform/x86: x86-android-tablets: Stop using EPROBE_DEFER
platform/x86: x86-android-tablets: Fix modules lists for Lenovo devices
platform/x86: x86-android-tablets: Simplify lenovo_yoga_tab2_830_1050_exit()
platform/x86: x86-android-tablets: Add support for Acer A1-840 tablet
platform/x86: x86-android-tablets: Move Acer info to its own file
platform/x86: x86-android-tablets: Update my email address
platform/x86: x86-android-tablets: Simplify node-group [un]registration
platform/x86: x86-android-tablets: use swnode_group instead of manual registering
platform/x86: x86-android-tablets: replace bat_swnode with swnode_group
platform/x86: x86-android-tablets: convert gpio_keys devices to GPIO references
platform/x86: x86-android-tablets: remove support for GPIO lookup tables
platform/x86: x86-android-tablets: convert Yoga Tab2 fast charger to GPIO references
platform/x86: x86-android-tablets: convert HID-I2C devices to GPIO references
platform/x86: x86-android-tablets: convert wm1502 devices to GPIO references
platform/x86: x86-android-tablets: convert int3496 devices to GPIO references
platform/x86: x86-android-tablets: convert EDT devices to GPIO references
platform/x86: x86-android-tablets: convert Novatek devices to GPIO references
...
|
||
|
Linus Torvalds
|
908057d185 |
Merge tag 'v6.18-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu: "Drivers: - Add ciphertext hiding support to ccp - Add hashjoin, gather and UDMA data move features to hisilicon - Add lz4 and lz77_only to hisilicon - Add xilinx hwrng driver - Add ti driver with ecb/cbc aes support - Add ring buffer idle and command queue telemetry for GEN6 in qat Others: - Use rcu_dereference_all to stop false alarms in rhashtable - Fix CPU number wraparound in padata" * tag 'v6.18-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (78 commits) dt-bindings: rng: hisi-rng: convert to DT schema crypto: doc - Add explicit title heading to API docs hwrng: ks-sa - fix division by zero in ks_sa_rng_init KEYS: X.509: Fix Basic Constraints CA flag parsing crypto: anubis - simplify return statement in anubis_mod_init crypto: hisilicon/qm - set NULL to qm->debug.qm_diff_regs crypto: hisilicon/qm - clear all VF configurations in the hardware crypto: hisilicon - enable error reporting again crypto: hisilicon/qm - mask axi error before memory init crypto: hisilicon/qm - invalidate queues in use crypto: qat - Return pointer directly in adf_ctl_alloc_resources crypto: aspeed - Fix dma_unmap_sg() direction rhashtable: Use rcu_dereference_all and rcu_dereference_all_check crypto: comp - Use same definition of context alloc and free ops crypto: omap - convert from tasklet to BH workqueue crypto: qat - Replace kzalloc() + copy_from_user() with memdup_user() crypto: caam - double the entropy delay interval for retry padata: WQ_PERCPU added to alloc_workqueue users padata: replace use of system_unbound_wq with system_dfl_wq crypto: cryptd - WQ_PERCPU added to alloc_workqueue users ... |
||
|
Linus Torvalds
|
d104e3d17f |
Merge tag 'cxl-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL updates from Dave Jiang:
"The changes include adding poison injection support, fixing CXL access
coordinates when onlining CXL memory, and delaing the enumeration of
downstream switch ports for CXL hierarchy to ensure that the CXL link
is established at the time of enumeration to address a few issues
observed on AMD and Intel platforms.
Misc changes:
- Use str_plural() instead of open code for emitting strings.
- Use str_enabled_disabled() instead of ternary operator
- Fix emit of type resource_size_t argument for
validate_region_offset()
- Typo fixup in CXL driver-api documentation
- Rename CFMWS coherency restriction defines
- Add convention doc describe dealing with x86 low memory hole
and CXL
Poison Inject support:
- Move hpa_to_spa callback to new reoot decoder ops structure
- Define a SPA to HPA callback for interleave calculation with
XOR math
- Add support for SPA to DPA address translation with XOR
- Add locked variants of poison inject and clear functions
- Add inject and clear poison support by region offset
CXL access coordinates update fix:
- A comment update for hotplug memory callback prority defines
- Add node_update_perf_attrs() for updating perf attrs on a node
- Update cxl_access_coordinates() to use the new node update function
- Remove hmat_update_target_coordinates() and related code
CXL delayed downstream port enumeration and initialization:
- Add helper to detect top of CXL device topology and remove
open coding
- Add helper to delete single dport
- Add a cached copy of target_map to cxl_decoder
- Refactor decoder setup to reduce cxl_test burden
- Defer dport allocation for switch ports
- Add mock version of devm_cxl_add_dport_by_dev() for cxl_test
- Adjust the mock version of devm_cxl_switch_port_decoders_setup()
due to cxl core usage
- Setup target_map for cxl_test decoder initialization
- Change SSLBIS handler to handle single dport
- Move port register setup to when first dport appears"
* tag 'cxl-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (25 commits)
cxl: Move port register setup to when first dport appear
cxl: Change sslbis handler to only handle single dport
cxl/test: Setup target_map for cxl_test decoder initialization
cxl/test: Adjust the mock version of devm_cxl_switch_port_decoders_setup()
cxl/test: Add mock version of devm_cxl_add_dport_by_dev()
cxl: Defer dport allocation for switch ports
cxl/test: Refactor decoder setup to reduce cxl_test burden
cxl: Add a cached copy of target_map to cxl_decoder
cxl: Add helper to delete dport
cxl: Add helper to detect top of CXL device topology
cxl: Documentation/driver-api/cxl: Describe the x86 Low Memory Hole solution
cxl/acpi: Rename CFMW coherency restrictions
Documentation/driver-api: Fix typo error in cxl
acpi/hmat: Remove now unused hmat_update_target_coordinates()
cxl, acpi/hmat: Update CXL access coordinates directly instead of through HMAT
drivers/base/node: Add a helper function node_update_perf_attrs()
mm/memory_hotplug: Update comment for hotplug memory callback priorities
cxl: Fix emit of type resource_size_t argument for validate_region_offset()
cxl/region: Add inject and clear poison by region offset
cxl/core: Add locked variants of the poison inject and clear funcs
...
|
||
|
Linus Torvalds
|
67da125e30 |
Merge tag 'rcu.2025.09.26a' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux
Pull RCU updates from Paul McKenney:
"Documentation updates:
- Update whatisRCU.rst and checklist.rst for recent RCU API additions
- Fix RCU documentation formatting and typos
- Replace dead Ottawa Linux Symposium links in RTFP.txt
Miscellaneous RCU updates:
- Document that rcu_barrier() hurries RCU_LAZY callbacks
- Remove redundant interrupt disabling from
rcu_preempt_deferred_qs_handler()
- Move list_for_each_rcu from list.h to rculist.h, and adjust the
include directive in kernel/cgroup/dmem.c accordingly
- Make initial set of changes to accommodate upcoming
system_percpu_wq changes
SRCU updates:
- Create an srcu_read_lock_fast_notrace() for eventual use in
tracing, including adding guards
- Document the reliance on per-CPU operations as implicit RCU readers
in __srcu_read_{,un}lock_fast()
- Document the srcu_flip() function's memory-barrier D's relationship
to SRCU-fast readers
- Remove a redundant preempt_disable() and preempt_enable() pair from
srcu_gp_start_if_needed()
Torture-test updates:
- Fix jitter.sh spin time so that it actually varies as advertised.
It is still quite coarse-grained, but at least it does now vary
- Update torture.sh help text to include the not-so-new --do-normal
parameter, which permits (for example) testing KCSAN kernels
without doing non-debug kernels
- Fix a number of false-positive diagnostics that were being
triggered by rcutorture starting before boot completed. Running
multiple near-CPU-bound rcutorture processes when there is only the
boot CPU is after all a bit excessive
- Substitute kcalloc() for kzalloc()
- Remove a redundant kfree() and NULL out kfree()ed objects"
* tag 'rcu.2025.09.26a' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux: (31 commits)
rcu: WQ_UNBOUND added to sync_wq workqueue
rcu: WQ_PERCPU added to alloc_workqueue users
rcu: replace use of system_wq with system_percpu_wq
refperf: Set reader_tasks to NULL after kfree()
refperf: Remove redundant kfree() after torture_stop_kthread()
srcu/tiny: Remove preempt_disable/enable() in srcu_gp_start_if_needed()
srcu: Document srcu_flip() memory-barrier D relation to SRCU-fast
srcu: Document __srcu_read_{,un}lock_fast() implicit RCU readers
rculist: move list_for_each_rcu() to where it belongs
refscale: Use kcalloc() instead of kzalloc()
rcutorture: Use kcalloc() instead of kzalloc()
docs: rcu: Replace multiple dead OLS links in RTFP.txt
doc: Fix typo in RCU's torture.rst documentation
Documentation: RCU: Retitle toctree index
Documentation: RCU: Reduce toctree depth
Documentation: RCU: Wrap kvm-remote.sh rerun snippet in literal code block
rcu: docs: Requirements.rst: Abide by conventions of kernel documentation
doc: Add RCU guards to checklist.rst
doc: Update whatisRCU.rst for recent RCU API additions
rcutorture: Delay forward-progress testing until boot completes
...
|
||
|
Linus Torvalds
|
86bcf7be1e |
Merge tag 'riscv-for-linus-6.18-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Paul Walmsley:
- Support for the RISC-V-standardized RPMI interface.
RPMI is a platform management communication mechanism between OSes
running on application processors, and a remote platform management
processor. Similar to ARM SCMI, TI SCI, etc. This includes irqchip,
mailbox, and clk changes.
- Support for the RISC-V-standardized MPXY SBI extension.
MPXY is a RISC-V-specific standard implementing a shared memory
mailbox between S-mode operating systems (e.g., Linux) and M-mode
firmware (e.g., OpenSBI). It is part of this PR since one of its use
cases is to enable M-mode firmware to act as a single RPMI client for
all RPMI activity on a core (including S-mode RPMI activity).
Includes a mailbox driver.
- Some ACPI-related updates to enable the use of RPMI and MPXY.
- The addition of Linux-wide memcpy_{from,to}_le32() static inline
functions, for RPMI use.
- An ACPI Kconfig change to enable boot logos on any ACPI-using
architecture (including RISC-V)
- A RISC-V defconfig change to add GPIO keyboard and event device
support, for front panel shutdown or reboot buttons
* tag 'riscv-for-linus-6.18-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (26 commits)
clk: COMMON_CLK_RPMI should depend on RISCV
ACPI: support BGRT table on RISC-V
MAINTAINERS: Add entry for RISC-V RPMI and MPXY drivers
RISC-V: Enable GPIO keyboard and event device in RV64 defconfig
irqchip/riscv-rpmi-sysmsi: Add ACPI support
mailbox/riscv-sbi-mpxy: Add ACPI support
irqchip/irq-riscv-imsic-early: Export imsic_acpi_get_fwnode()
ACPI: RISC-V: Add RPMI System MSI to GSI mapping
ACPI: RISC-V: Add support to update gsi range
ACPI: RISC-V: Create interrupt controller list in sorted order
ACPI: scan: Update honor list for RPMI System MSI
ACPI: Add support for nargs_prop in acpi_fwnode_get_reference_args()
ACPI: property: Refactor acpi_fwnode_get_reference_args() to support nargs_prop
irqchip: Add driver for the RPMI system MSI service group
dt-bindings: Add RPMI system MSI interrupt controller bindings
dt-bindings: Add RPMI system MSI message proxy bindings
clk: Add clock driver for the RISC-V RPMI clock service group
dt-bindings: clock: Add RPMI clock service controller bindings
dt-bindings: clock: Add RPMI clock service message proxy bindings
mailbox: Add RISC-V SBI message proxy (MPXY) based mailbox driver
...
|
||
|
Linus Torvalds
|
50ac57c3b1 |
Merge tag 'x86_tdx_for_6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 TDX updates from Dave Hansen:
"The biggest change here is making TDX and kexec play nicely together.
Before this, the memory encryption hardware (which doesn't respect
cache coherency) could write back old cachelines on top of data in the
new kernel, so kexec and TDX were made mutually exclusive. This
removes the limitation.
There is also some work to tighten up a hardware bug workaround and
some MAINTAINERS updates.
- Make TDX and kexec work together
- Skip TDX bug workaround when the bug is not present
- Update maintainers entries"
* tag 'x86_tdx_for_6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/virt/tdx: Use precalculated TDVPR page physical address
KVM/TDX: Explicitly do WBINVD when no more TDX SEAMCALLs
x86/virt/tdx: Update the kexec section in the TDX documentation
x86/virt/tdx: Remove the !KEXEC_CORE dependency
x86/kexec: Disable kexec/kdump on platforms with TDX partial write erratum
x86/virt/tdx: Mark memory cache state incoherent when making SEAMCALL
x86/sme: Use percpu boolean to control WBINVD during kexec
x86/kexec: Consolidate relocate_kernel() function parameters
x86/tdx: Skip clearing reclaimed pages unless X86_BUG_TDX_PW_MCE is present
x86/tdx: Tidy reset_pamt functions
x86/tdx: Eliminate duplicate code in tdx_clear_page()
MAINTAINERS: Add KVM mail list to the TDX entry
MAINTAINERS: Add Rick Edgecombe as a TDX reviewer
MAINTAINERS: Update the file list in the TDX entry.
|