If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e7 ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return result of b44_writephy() instead of zero to
deal with possible error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 01f4fd2708 ("bonding: Fix incorrect deletion of
ETH_P_8021AD protocol vid from slaves"), we can trigger BUG_ON(!vlan_info)
in unregister_vlan_dev() with the following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add team1 type team
# ip netns exec ns1 ip link add team_slave type veth peer veth2
# ip netns exec ns1 ip link set team_slave master team1
# ip netns exec ns1 ip link add link team_slave name team_slave.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link team1 name team1.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set team_slave nomaster
# ip netns del ns1
Add S-VLAN tag related features support to team driver. So the team driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230814032301.2804971-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If it fails to get the devices's MAC address, octep_probe exits while
leaving the delayed work intr_poll_task queued. When the work later
runs, it's a use after free.
Move the cancelation of intr_poll_task from octep_remove into
octep_device_cleanup. This does not change anything in the octep_remove
flow, but octep_device_cleanup is called also in the octep_probe error
path, where the cancelation is needed.
Note that the cancelation of ctrl_mbox_task has to follow
intr_poll_task's, because the ctrl_mbox_task may be queued by
intr_poll_task.
Fixes: 24d4333233 ("octeon_ep: poll for control messages")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-5-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
intr_poll_task may queue ctrl_mbox_task. The function
octep_poll_non_ioq_interrupts_cn93_pf does this.
When removing the driver and canceling these two works, cancel
ctrl_mbox_task last to guarantee it does not run anymore.
Fixes: 24d4333233 ("octeon_ep: poll for control messages")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-4-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tx_timeout_task is canceled too early when removing the driver. Nothing
prevents .ndo_tx_timeout from triggering and queuing the work again.
Better cancel it after the netdev is unregistered.
It's harmless for octep_tx_timeout_task to run in the window between the
unregistration and cancelation, because it checks netif_running.
Fixes: 862cd659a6 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://lore.kernel.org/r/20230810150114.107765-3-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On Zynq UltraScale+ MPSoC ubuntu platform when systemctl issues suspend,
network manager bring down the interface and goes into suspend. When it
wakes up it again enables the interface.
This leads to xilinx-psgtr "PLL lock timeout" on interface bringup, as
the power management controller power down the entire FPD (including
SERDES) if none of the FPD devices are in use and serdes is not
initialized on resume.
$ sudo rtcwake -m no -s 120 -v
$ sudo systemctl suspend <this does ifconfig eth1 down>
$ ifconfig eth1 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
macb driver is called in this way:
1. macb_close: Stop network interface. In this function, it
reset MACB IP and disables PHY and network interface.
2. macb_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into suspend state. Some time later, system is
waken up by RTC wakeup device;
4. macb_resume: It does nothing because network interface has
been disabled;
5. macb_open: It is called to enable network interface again. ethernet
interface is initialized in this API but serdes which is power-off
by PMUFW during FPD-off suspend is not initialized again and so
we hit GT PLL lock issue on open.
To resolve this PLL timeout issue always do PS GTR initialization
when ethernet device is configured as non-wakeup source.
Fixes: f22bd29ba1 ("net: macb: Fix ZynqMP SGMII non-wakeup source resume failure")
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691414091-2260697-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Uwe reports:
"Most PHYs signal WoL using an interrupt. So disabling interrupts [at
shutdown] breaks WoL at least on PHYs covered by the marvell driver."
Discussing with Ioana, the problem which was trying to be solved was:
"The board in question is a LS1021ATSN which has two AR8031 PHYs that
share an interrupt line. In case only one of the PHYs is probed and
there are pending interrupts on the PHY#2 an IRQ storm will happen
since there is no entity to clear the interrupt from PHY#2's registers.
PHY#1's driver will get stuck in .handle_interrupt() indefinitely."
Further confirmation that "the two AR8031 PHYs are on the same MDIO
bus."
With WoL using interrupts to wake the system, in such a case, the
system will begin booting with an asserted interrupt. Thus, we need to
cope with an interrupt asserted during boot.
Solve this instead by disabling interrupts during PHY probe. This will
ensure in Ioana's situation that both PHYs of the same type sharing an
interrupt line on a common MDIO bus will have their interrupt outputs
disabled when the driver probes the device, but before we hook in any
interrupt handlers - thus avoiding the interrupt storm.
A better fix would be for platform firmware to disable the interrupting
devices at source during boot, before control is handed to the kernel.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reference of pdev->dev is taken by of_find_device_by_node, so
it should be released when not need anymore.
Fixes: 7dc54d3b8d ("net: pcs: add Renesas MII converter driver")
Signed-off-by: Xiang Yang <xiangyang3@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 25266128fe ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wireless and bpf.
Still trending up in size but the good news is that the "current"
regressions are resolved, AFAIK.
We're getting weirdly many fixes for Wake-on-LAN and suspend/resume
handling on embedded this week (most not merged yet), not sure why.
But those are all for older bugs.
Current release - regressions:
- tls: set MSG_SPLICE_PAGES consistently when handing encrypted data
over to TCP
Current release - new code bugs:
- eth: mlx5: correct IDs on VFs internal to the device (IPU)
Previous releases - regressions:
- phy: at803x: fix WoL support / reporting on AR8032
- bonding: fix incorrect deletion of ETH_P_8021AD protocol VID from
slaves, leading to BUG_ON()
- tun: prevent tun_build_skb() from exceeding the packet size limit
- wifi: rtw89: fix 8852AE disconnection caused by RX full flags
- eth/PCI: enetc: fix probing after 6fffbc7ae1 ("PCI: Honor
firmware's device disabled status"), keep PCI devices around even
if they are disabled / not going to be probed to be able to apply
quirks on them
- eth: prestera: fix handling IPv4 routes with nexthop IDs
Previous releases - always broken:
- netfilter: re-work garbage collection to avoid races between
user-facing API and timeouts
- tunnels: fix generating ipv4 PMTU error on non-linear skbs
- nexthop: fix infinite nexthop bucket dump when using maximum
nexthop ID
- wifi: nl80211: fix integer overflow in nl80211_parse_mbssid_elems()
Misc:
- unix: use consistent error code in SO_PEERPIDFD
- ipv6: adjust ndisc_is_useropt() to include PREFIX_INFO, in prep for
upcoming IETF RFC"
* tag 'net-6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
net: hns3: fix strscpy causing content truncation issue
net: tls: set MSG_SPLICE_PAGES consistently
ibmvnic: Ensure login failure recovery is safe from other resets
ibmvnic: Do partial reset on login failure
ibmvnic: Handle DMA unmapping of login buffs in release functions
ibmvnic: Unmap DMA login rsp buffer on send login fail
ibmvnic: Enforce stronger sanity checks on login response
net: mana: Fix MANA VF unload when hardware is unresponsive
netfilter: nf_tables: remove busy mark and gc batch API
netfilter: nft_set_hash: mark set element as dead when deleting from packet path
netfilter: nf_tables: adapt set backend to use GC transaction API
netfilter: nf_tables: GC transaction API to avoid race with control plane
selftests/bpf: Add sockmap test for redirecting partial skb data
selftests/bpf: fix a CI failure caused by vsock sockmap test
bpf, sockmap: Fix bug that strp_done cannot be called
bpf, sockmap: Fix map type error in sock_map_del_link
xsk: fix refcount underflow in error path
ipv6: adjust ndisc_is_useropt() to also return true for PIO
selftests: forwarding: bridge_mdb: Make test more robust
selftests: forwarding: bridge_mdb_max: Fix failing test with old libnet
...
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f ("net: hns3: fix strncpy() not using dest-buf length as length issue")
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e7 ("ibmvnic: Harden device login requests")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When unloading the MANA driver, mana_dealloc_queues() waits for the MANA
hardware to complete any inflight packets and set the pending send count
to zero. But if the hardware has failed, mana_dealloc_queues()
could wait forever.
Fix this by adding a timeout to the wait. Set the timeout to 120 seconds,
which is a somewhat arbitrary value that is more than long enough for
functional hardware to complete any sends.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/1691576525-24271-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Just a few small updates:
* fix an integer overflow in nl80211
* fix rtw89 8852AE disconnections
* fix a buffer overflow in ath12k
* fix AP_VLAN configuration lookups
* fix allocation failure handling in brcm80211
* update MAINTAINERS for some drivers
* tag 'wireless-2023-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: ath12k: Fix buffer overflow when scanning with extraie
wifi: nl80211: fix integer overflow in nl80211_parse_mbssid_elems()
wifi: cfg80211: fix sband iftype data lookup for AP_VLAN
wifi: rtw89: fix 8852AE disconnection caused by RX full flags
MAINTAINERS: Remove tree entry for rtl8180
MAINTAINERS: Update entry for rtl8187
wifi: brcm80211: handle params_v1 allocation failure
====================
Link: https://lore.kernel.org/r/20230809124818.167432-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If cfg80211 is providing extraie's for a scanning process then ath12k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The problem is the allocation of the buffer. It has to align the TLV
sections by 4 bytes. But the code was using an u8 to store the newly
calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual
code to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a wifi card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230809081241.32765-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 6fffbc7ae1 ("PCI: Honor firmware's device disabled
status"), this is redundant and does nothing, because enetc_pf_probe()
no longer even gets called.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround implemented in commit 3222b5b613 ("net: enetc:
initialize RFS/RSS memories for unused ports too") is no longer
effective after commit 6fffbc7ae1 ("PCI: Honor firmware's device
disabled status"). Thus, it has introduced a regression and we see AER
errors being reported again:
$ ip link set sw2p0 up && dhclient -i sw2p0 && ip addr show sw2p0
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 2.5Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp2: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control off
sja1105 spi2.2 sw2p0: configuring for phy/rgmii-id link mode
sja1105 spi2.2 sw2p0: Link is Up - 1Gbps/Full - flow control off
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
pcieport 0000:00:1f.0: AER: can't find device of ID0000
Rob's suggestion is to reimplement the enetc driver workaround as a
PCI fixup, and to modify the PCI core to run the fixups for all PCI
functions. This change handles the first part.
We refactor the common code in enetc_psi_create() and enetc_psi_destroy(),
and use the PCI fixup only for those functions for which enetc_pf_probe()
won't get called. This avoids some work being done twice for the PFs
which are enabled.
Fixes: 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
Link: https://lore.kernel.org/netdev/CAL_JsqLsVYiPLx2kcHkDQ4t=hQVCR7NHziDwi9cCFUFhx48Qow@mail.gmail.com/
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fdir_fltr_lock locking in unprotected places.
The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf06 ("iavf: Support IPv4 Flow Director filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5 fixes 2023-08-07
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Add capability check for vnic counters
net/mlx5: Reload auxiliary devices in pci error handlers
net/mlx5: Skip clock update work when device is in error state
net/mlx5: LAG, Check correct bucket when modifying LAG
net/mlx5e: Unoffload post act rule when handling FIB events
net/mlx5: Fix devlink controller number for ECVF
net/mlx5: Allow 0 for total host VFs
net/mlx5: Return correct EC_VF function ID
net/mlx5: DR, Fix wrong allocation of modify hdr pattern
net/mlx5e: TC, Fix internal port memory leak
net/mlx5e: Take RTNL lock when needed before calling xdp_set_features()
====================
Link: https://lore.kernel.org/r/20230807212607.50883-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When externel_lb and reset are executed together, a deadlock may
occur:
[ 3147.217009] INFO: task kworker/u321:0:7 blocked for more than 120 seconds.
[ 3147.230483] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 3147.238999] task:kworker/u321:0 state:D stack: 0 pid: 7 ppid: 2 flags:0x00000008
[ 3147.248045] Workqueue: hclge hclge_service_task [hclge]
[ 3147.253957] Call trace:
[ 3147.257093] __switch_to+0x7c/0xbc
[ 3147.261183] __schedule+0x338/0x6f0
[ 3147.265357] schedule+0x50/0xe0
[ 3147.269185] schedule_preempt_disabled+0x18/0x24
[ 3147.274488] __mutex_lock.constprop.0+0x1d4/0x5dc
[ 3147.279880] __mutex_lock_slowpath+0x1c/0x30
[ 3147.284839] mutex_lock+0x50/0x60
[ 3147.288841] rtnl_lock+0x20/0x2c
[ 3147.292759] hclge_reset_prepare+0x68/0x90 [hclge]
[ 3147.298239] hclge_reset_subtask+0x88/0xe0 [hclge]
[ 3147.303718] hclge_reset_service_task+0x84/0x120 [hclge]
[ 3147.309718] hclge_service_task+0x2c/0x70 [hclge]
[ 3147.315109] process_one_work+0x1d0/0x490
[ 3147.319805] worker_thread+0x158/0x3d0
[ 3147.324240] kthread+0x108/0x13c
[ 3147.328154] ret_from_fork+0x10/0x18
In externel_lb process, the hns3 driver call napi_disable()
first, then the reset happen, then the restore process of the
externel_lb will fail, and will not call napi_enable(). When
doing externel_lb again, napi_disable() will be double call,
cause a deadlock of rtnl_lock().
This patch use the HNS3_NIC_STATE_DOWN state to protect the
calling of napi_disable() and napi_enable() in externel_lb
process, just as the usage in ndo_stop() and ndo_start().
Fixes: 04b6ba1435 ("net: hns3: add support for external loopback test")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230807113452.474224-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <jasowang@redhat.com> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
Fixes: 7df13219d7 ("tun: reserve extra headroom only when XDP is set")
Link: https://syzkaller.appspot.com/bug?extid=f817490f5bd20541b90a
Signed-off-by: Andrew Kanner <andrew.kanner@gmail.com>
Link: https://lore.kernel.org/r/20230803185947.2379988-1-andrew.kanner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull xen netback buffer overflow fix from Juergen Gross:
"The fix for XSA-423 added logic to Linux'es netback driver to deal
with a frontend splitting a packet in a way such that not all of the
headers would come in one piece.
Unfortunately the logic introduced there didn't account for the
extreme case of the entire packet being split into as many pieces as
permitted by the protocol, yet still being smaller than the area
that's specially dealt with to keep all (possible) headers together.
Such an unusual packet would therefore trigger a buffer overrun in the
driver"
* tag 'xsa432-6.5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/netback: Fix buffer overrun triggered by unusual packet
In the allowedips self-test, nodes are inserted into the tree, but it
generated an even amount of nodes, but for checking maximum node depth,
there is of course the root node, which makes the total number
necessarily odd. With two few nodes added, it never triggered the
maximum depth check like it should have. So, add 129 nodes instead of
128 nodes, and do so with a more straightforward scheme, starting with
all the bits set, and shifting over one each time. Then increase the
maximum depth to 129, and choose a better name for that variable to
make it clear that it represents depth as opposed to bits.
Cc: stable@vger.kernel.org
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20230807132146.2191597-2-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230802114320.4156068-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing capability check for each of the vnic counters exposed by
devlink health reporter, and thus avoid unexpected behavior due to
invalid access to registers.
While at it, read only the exact number of bits for each counter whether
it was 32 bits or 64 bits.
Fixes: b0bc615df4 ("net/mlx5: Add vnic devlink health reporter to PFs/VFs")
Fixes: a33682e4e7 ("net/mlx5e: Expose catastrophic steering error counters")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Handling pci errors should fully teardown and load back auxiliary
devices, same as done through mlx5 health recovery flow.
Fixes: 72ed5d5624 ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Reported-and-tested-by: Ganesh G R <ganeshgr@linux.ibm.com>
Closes: https://lore.kernel.org/netdev/9bdb9b9d-140a-7a28-f0de-2e64e873c068@nvidia.com
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Cited patch introduced buckets in hash mode, but missed to update
the ports/bucket check when modifying LAG.
Fix the check.
Fixes: 352899f384 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The controller number for ECVFs is always 0, because the ECPF must be
the eswitch owner for EC VFs to be enabled.
Fixes: dc13180824 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50bea ("net/mlx5: Support querying max VFs from device");
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The ECVF function ID range is 1..max_ec_vfs. Currently
mlx5_vport_to_func_id returns 0..max_ec_vfs - 1. Which
results in a syndrome when querying the caps with more
recent firmware, or reading incorrect caps with older
firmware that supports EC VFs.
Fixes: 9ac0b12824 ("net/mlx5: Update vport caps query/set for EC VFs")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fixing wrong calculation of the modify hdr pattern size,
where the previously calculated number would not be enough
to accommodate the required number of actions.
Fixes: da5d0027d6 ("net/mlx5: DR, Add cache for modify header pattern")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The flow rule can be splited, and the extra post_act rules are added
to post_act table. It's possible to trigger memleak when the rule
forwards packets from internal port and over tunnel, in the case that,
for example, CT 'new' state offload is allowed. As int_port object is
assigned to the flow attribute of post_act rule, and its refcnt is
incremented by mlx5e_tc_int_port_get(), but mlx5e_tc_int_port_put() is
not called, the refcnt is never decremented, then int_port is never
freed.
The kmemleak reports the following error:
unreferenced object 0xffff888128204b80 (size 64):
comm "handler20", pid 50121, jiffies 4296973009 (age 642.932s)
hex dump (first 32 bytes):
01 00 00 00 19 00 00 00 03 f0 00 00 04 00 00 00 ................
98 77 67 41 81 88 ff ff 98 77 67 41 81 88 ff ff .wgA.....wgA....
backtrace:
[<00000000e992680d>] kmalloc_trace+0x27/0x120
[<000000009e945a98>] mlx5e_tc_int_port_get+0x3f3/0xe20 [mlx5_core]
[<0000000035a537f0>] mlx5e_tc_add_fdb_flow+0x473/0xcf0 [mlx5_core]
[<0000000070c2cec6>] __mlx5e_add_fdb_flow+0x7cf/0xe90 [mlx5_core]
[<000000005cc84048>] mlx5e_configure_flower+0xd40/0x4c40 [mlx5_core]
[<000000004f8a2031>] mlx5e_rep_indr_offload.isra.0+0x10e/0x1c0 [mlx5_core]
[<000000007df797dc>] mlx5e_rep_indr_setup_tc_cb+0x90/0x130 [mlx5_core]
[<0000000016c15cc3>] tc_setup_cb_add+0x1cf/0x410
[<00000000a63305b4>] fl_hw_replace_filter+0x38f/0x670 [cls_flower]
[<000000008bc9e77c>] fl_change+0x1fd5/0x4430 [cls_flower]
[<00000000e7f766e4>] tc_new_tfilter+0x867/0x2010
[<00000000e101c0ef>] rtnetlink_rcv_msg+0x6fc/0x9f0
[<00000000e1111d44>] netlink_rcv_skb+0x12c/0x360
[<0000000082dd6c8b>] netlink_unicast+0x438/0x710
[<00000000fc568f70>] netlink_sendmsg+0x794/0xc50
[<0000000016e92590>] sock_sendmsg+0xc5/0x190
So fix this by moving int_port cleanup code to the flow attribute
free helper, which is used by all the attribute free cases.
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
