On some platforms, the UFS-reset pin has no interrupt logic in TLMM but
is nevertheless registered as a GPIO in the kernel. This enables the
user-space to trigger a BUG() in the pinctrl-msm driver by running, for
example: `gpiomon -c 0 113` on RB2.
The exact culprit is requesting pins whose intr_detection_width setting
is not 1 or 2 for interrupts. This hits a BUG() in
msm_gpio_irq_set_type(). Potentially crashing the kernel due to an
invalid request from user-space is not optimal, so let's go through the
pins and mark those that would fail the check as invalid for the irq chip
as we should not even register them as available irqs.
This function can be extended if we determine that there are more
corner-cases like this.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/20250612091448.41546-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"An especially linear and sparse improvement and new drivers release.
Nothing exciting. The biggest change in Bartosz changes to make
gpiochip set/get calls return error codes (something we should have
fixed ages ago but is now finally getting fixed.)
Core changes:
- Add the devres devm_pinctrl_register_mappings() call that can
register some pin control machine mappings and have them go away
with the associated device
New drivers:
- Support for the Mediatek MT6893 and MT8196 SoCs
- Support for the Renesas RZ/V2N SoC
- Support for the NXP Freescale i.MX943 SoC
Improvements:
- Per-SoC suspend/resume callbacks in the Samsung drivers
- Set all pins as input (High-Z) at probe in the MCP23S08 driver
- Switch most GPIO chips to use the setters/getters with a return
value
- EGPIO support in the Qualcomm QCM2290 driver
- Fix up the number of available GPIO lines in Qualcomm QCS8300 and
QCS615"
* tag 'pinctrl-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: freescale: Add support for imx943 pinctrl
pinctrl: core: add devm_pinctrl_register_mappings()
pinctrl: remove extern specifier for functions in machine.h
pinctrl: mediatek: eint: Fix invalid pointer dereference for v1 platforms
pinctrl: freescale: Enable driver if platform is enabled.
pinctrl: freescale: Depend imx-scu driver on OF
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_set_by_name()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_pmx_gpio_set_direction()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_get()
pinctrl: armada-37xx: propagate error from armada_37xx_gpio_direction_output()
pinctrl: armada-37xx: set GPIO output value before setting direction
pinctrl: armada-37xx: use correct OUTPUT_VAL register for GPIOs > 31
pinctrl: meson: Drop unused aml_pctl_find_group_by_name()
pinctrl: at91: Fix possible out-of-boundary access
pinctrl: add stubs for OF-specific pinconf functions
pinctrl: qcom: correct the ngpios entry for QCS8300
pinctrl: qcom: correct the ngpios entry for QCS615
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs8300
dt-bindings: pinctrl: qcom: correct gpio-ranges in examples for qcs615
...
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While looking at the X1E PDC GPIO interrupts it became clear that we're
lacking a convenient and accessible way to validate if the TLMM
interrupt code performing as expected.
This introduces a kunit-based "hack" that relies on pin bias/pull
configuration to tickle the interrupt logic in non-connected pins to
allow us to evaluate that an expected number of interrupts are
delivered.
The bias/pull configuration is done with mmio accesses directly from the
test code, to avoid having to programmatically acquire and drive the
pinconf interface for the test pin. This limits the scalability of the
code to targets with a particular register layout, but serves our needs
for now.
The pin to be used for testing is specified by the tester using the
"tlmm-test.gpio" module parameter.
Worth mentioning is that some of the test cases currently fails for
GPIOs that is not backed by PDC (i.e. "non-wakeup" GPIOs), as lingering
latched interrupt state is being delivered at IRQ request time.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 723e8462a4 ("pinctrl: qcom: spmi-gpio: Fix the GPIO strength
mapping") fixed a long-standing issue in the Qualcomm SPMI PMIC gpio
driver which had the 'low' and 'high' drive strength settings switched
but failed to update the debugfs interface which still gets this wrong.
Fix the debugfs code so that the exported values match the hardware
settings.
Note that this probably means that most devicetrees that try to describe
the firmware settings got this wrong if the settings were derived from
debugfs. Before the above mentioned commit the settings would have
actually matched the firmware settings even if they were described
incorrectly, but now they are inverted.
Fixes: 723e8462a4 ("pinctrl: qcom: spmi-gpio: Fix the GPIO strength mapping")
Fixes: eadff30244 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Cc: Anjelique Melendez <quic_amelende@quicinc.com>
Cc: stable@vger.kernel.org # 3.19
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/20241025121622.1496-1-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/pinctrl to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/20241007205803.444994-8-u.kleine-koenig@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On X1E80100, GPIO interrupts for wakeup-capable pins have been broken since
the introduction of the pinctrl driver. This prevents keyboard and touchpad
from working on most of the X1E laptops. So far we have worked around this
by manually building a kernel with the "wakeup-parent" removed from the
pinctrl node in the device tree, but we cannot expect all users to do that.
Implement a similar workaround in the driver by clearing the wakeirq_map
for X1E80100. This avoids using the PDC wakeup parent for all GPIOs
and handles the interrupts directly in the pinctrl driver instead.
The PDC driver needs additional changes to support X1E80100 properly.
Adding a workaround separately first allows to land the necessary PDC
changes through the normal release cycle, while still solving the more
critical problem with keyboard and touchpad on the current stable kernel
versions. Bypassing the PDC is enough for now, because we have not yet
enabled the deep idle states where using the PDC becomes necessary.
Cc: stable@vger.kernel.org
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/20240830-x1e80100-bypass-pdc-v1-1-d4c00be0c3e3@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"Some new drivers is the main part, the rest is cleanups and nonurgent
fixes.
Nothing much special about this, no core changes this time.
New drivers:
- Renesas RZ/V2H(P) SoC
- NXP Freescale i.MX91 SoC
- Nuvoton MA35D1 SoC
- Qualcomm PMC8380, SM4250, SM4250 LPI
Enhancements:
- A slew of scoped-based simplifications of of_node_put()"
* tag 'pinctrl-v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (110 commits)
pinctrl: renesas: rzg2l: Support output enable on RZ/G2L
pinctrl: renesas: rzg2l: Clean up and refactor OEN read/write functions
pinctrl: renesas: rzg2l: Clarify OEN read/write support
dt-bindings: pinctrl: pinctrl-single: Fix pinctrl-single,gpio-range description
dt-bindings: pinctrl: npcm8xx: add missing pin group and mux function
dt-bindings: pinctrl: pinctrl-single: fix schmitt related properties
pinctrl: freescale: Use scope based of_node_put() cleanups
pinctrl: equilibrium: Use scope based of_node_put() cleanups
pinctrl: ti: iodelay: Use scope based of_node_put() cleanups
pinctrl: qcom: lpass-lpi: increase MAX_NR_GPIO to 32
pinctrl: cy8c95x0: Update cache modification
pinctrl: cy8c95x0: Use cleanup.h
pinctrl: renesas: r8a779h0: Remove unneeded separators
pinctrl: renesas: r8a779g0: Add INTC-EX pins, groups, and function
pinctrl: renesas: r8a779g0: Remove unneeded separators
pinctrl: renesas: r8a779h0: Add AVB MII pins and groups
pinctrl: renesas: r8a779g0: Fix TPU suffixes
pinctrl: renesas: r8a779g0: Fix TCLK suffixes
pinctrl: renesas: r8a779g0: FIX PWM suffixes
pinctrl: renesas: r8a779g0: Fix IRQ suffixes
...
The PDC was hooked up as a wakeup parent in the DTS in
commit 71f080633d ("arm64: dts: qcom: sdm670: Hook up PDC as
wakeup-parent of TLMM"), but the wakeirq mapping was not defined so it
had no effect. Add the mapping for wakeup interrupts on the PDC to their
corresponding pins.
Configuring a pin IRQ as dual-edge would break it unless the
wakeirq_dual_edge_errata flag is set.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20240523230619.256882-2-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPMI GPIO driver assumes that the parent device is an SPMI device
and accesses random data when backcasting the parent struct device
pointer for non-SPMI devices.
Fortunately this does not seem to cause any issues currently when the
parent device is an I2C client like the PM8008, but this could change if
the structures are reorganised (e.g. using structure randomisation).
Notably the interrupt implementation is also broken for non-SPMI devices.
Also note that the two GPIO pins on PM8008 are used for interrupts and
reset so their practical use should be limited.
Drop the broken GPIO support for PM8008 for now.
Fixes: ea119e5a48 ("pinctrl: qcom-pmic-gpio: Add support for pm8008")
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240529162958.18081-9-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
