This is a preparation patch for the introduction of CAN XL.
CAN FD and CAN XL uses similar bittiming parameters. Add one level of
nesting for all the CAN FD parameters. Typically:
priv->can.data_bittiming;
becomes:
priv->can.fd.data_bittiming;
This way, the CAN XL equivalent (to be introduced later) would be:
priv->can.xl.data_bittiming;
Add the new struct data_bittiming_params which contains all the data
bittiming parameters, including the TDC and the callback functions.
This done, update all the CAN FD drivers to make use of the new
layout.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250501171213.2161572-2-mailhol.vincent@wanadoo.fr
[mkl: fix rcar_canfd]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-2-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rockchip_canfd driver doesn't make use of the TXE FIFO.
Although the comment states that the TXE FIFO is setup, it's actually
a setup of the RX FIFO. The regular setup of the RX FIFO follows.
Remove the duplicated setup of the RX FIFO.
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Link: https://patch.msgid.link/20250219-rk3568-canfd-v1-1-453869358c72@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
drivers/net/can/rockchip/rockchip_canfd-core.c:770:20: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
770 | .ndo_start_xmit = rkcanfd_start_xmit,
| ^~~~~~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int' (although the types are ABI compatible). Adjust
the return type of rkcanfd_start_xmit() to match the prototype's to
resolve the warning.
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20240906-rockchip-canfd-wifpts-v1-1-b1398da865b7@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
So far the TX-FIFO is only used with a depth of 1, although the
hardware offers a depth of 2.
The workaround for the chips that are affected by erratum 6, i.e. EFF
frames may be send as standard frames, is to re-send the EFF frame.
This means the driver cannot queue the next frame for sending, as long
ad the EFF frame has not been successfully send out.
Introduce rkcanfd_get_effective_tx_free() that returns "0" space in
the TX-FIFO if an EFF frame is pending and the actual free space in
the TX-FIFO otherwise. Then replace rkcanfd_get_tx_free() with
rkcanfd_get_effective_tx_free() everywhere.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-16-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tests show that sometimes both CAN bus error counters read 0x0, even
if the controller is in warning mode
(RKCANFD_REG_STATE_ERROR_WARNING_STATE in RKCANFD_REG_STATE
set).
To work around this issue, if both error counters read from hardware
are 0x0, use the structure priv->bec, otherwise save the read value in
priv->bec.
In rkcanfd_handle_rx_int_one() decrement the priv->bec.rxerr for
successfully RX'ed CAN frames.
In rkcanfd_handle_tx_done_one() decrement the priv->bec.txerr for
successfully TX'ed CAN frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-14-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| A dominant bit at the third bit of the intermission may cause a
| transmission error.
|
| When sampling the third bit of the intermission as a dominant bit, if
| tx_req is configured to transmit extended frames at this time, the
| extended frame may be sent to the bus in the format of a standard
| frame. The extended frame will be sent as a standard frame and will not
| result in error frames
Turn on "Interframe Spaceing RX Mode" only during TX to work around
erratum 12, according to rock-chip:
| Spaceing RX Mode = 1, the third Bit between frames cannot receive
| and send, and the fourth Bit begins to receive and send.
|
| Spaceing RX Mode = 0, allowing the third Bit between frames to
| receive and send.
Message-ID: <be72939f-0a9e-0608-dfff-7b0096a26eba@rock-chips.com>
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-13-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| The CAN controller's transmission of extended frames may
| intermittently change into standard frames.
|
| When using the CAN controller to send extended frames, if the
| 'tx_req' is configured as 1 and coincides with the internal
| transmission point, the extended frame will be transmitted onto the
| bus in the format of a standard frame.
To work around Erratum 6, the driver is in self-receiving mode (RXSTX)
and all received CAN frames are passed through rkcanfd_rxstx_filter().
Add a check in rkcanfd_rxstx_filter() whether the received frame
corresponds to the current outgoing frame, but the extended CAN ID has
been mangled to a standard ID. In this case re-send the original CAN
frame.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-12-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The IP core has a TX event FIFO. In other IP cores, this type of FIFO
usually contains the events that a CAN frame has been successfully
sent. However, the IP core on the rk3568v2 the FIFO also holds events
of unsuccessful transmission attempts.
It turned out that the best way to work around this problem is to set
the IP core to self-receive mode (RXSTX), filter out the self-received
frames and insert them into the complete TX path.
Add a pair new functions to check if 2 struct canfd_frame are equal.
The 1st checks if the header of the CAN frames are equal, the 2nd
checks if the data portion are equal:
- rkcanfd_can_frame_header_equal()
- rkcanfd_can_frame_data_equal()
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-11-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rk3568 CAN-FD errata sheet as of Tue 07 Nov 2023 11:25:31 +08:00
says:
| Erratum 5: Counters related to the TXFIFO and RXFIFO exhibit
| abnormal counting behavior.
|
| Due to a bug in the cross-asynchronous logic of the enable signals
| for rx_fifo_cnt and txe_fifo_frame_cnt counters, the counts of these
| two counters become inaccurate. This issue has resulted in the
| inability to use the TXFIFO and RXFIFO functions.
The errata sheet mentioned above states that only the rk3568v2 is
affected by this erratum, but tests with the rk3568v2 and rk3568v3
show that the RX_FIFO_CNT is sometimes too high. This leads to CAN
frames being read from the FIFO, which is then already empty.
Further tests on the rk3568v2 and rk3568v3 show that in this
situation (i.e. empty FIFO) all elements of the FIFO
header (frameinfo, id, ts) contain the same data.
On the rk3568v2 and rk3568v3, this problem only occurs extremely
rarely with the standard clock of 300 MHz, but almost immediately at
80 MHz.
To workaround this problem, check for empty FIFO with
rkcanfd_fifo_header_empty() in rkcanfd_handle_rx_int_one() and exit
early.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-9-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add driver for the Rockchip CAN-FD controller.
The IP core on the rk3568v2 SoC has 12 documented errata. Corrections
for these errata will be added in the upcoming patches.
Since several workarounds are required for the TX path, only add the
base driver that only implements the RX path.
Although the RX path implements CAN-FD support, it's not activated in
ctrlmode_supported, as the IP core in the rk3568v2 has problems with
receiving or sending certain CAN-FD frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-4-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
