DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-spaces or
mixtures 2- and 4-spaces in one binding. While re-indenting, drop
unused labels.
No functional changes here, but saves some comments during reviews of
new patches built on existing code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250501145125.59952-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
The Samsung S2MPG10 PMIC is similar to the existing PMICs supported by
this binding.
It is a Power Management IC for mobile applications with buck
converters, various LDOs, power meters, RTC, clock outputs, and
additional GPIOs interfaces.
Unlike other Samsung PMICs, communication is not via I2C, but via the
Samsung ACPM firmware, it therefore doesn't need a 'reg' property but
needs to be a child of the ACPM firmware node instead.
S2MPG10 can also act as a system power controller allowing
implementation of a true cold-reset of the system.
Support for the other components like regulators and power meters will
be added in subsequent future patches.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250409-s2mpg10-v4-1-d66d5f39b6bf@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Split installation instructions for Ubuntu into 2 different sections:
- For Ubuntu 25.04: this release provides easy-to-install Rust packages.
- For Ubuntu 24.10 and below: these releases provide rust-1.80 and
bindgen-0.65, which do not set their tools as defaults. The instructions
for these versions have been updated to configure Rust tools properly.
Signed-off-by: Igor Korotin <igor.korotin@yahoo.com>
Link: https://lore.kernel.org/r/20250402160047.1827500-1-igor.korotin@yahoo.com
[ Dropped 24.10 -- it is soon out of support and their `bindgen` issue
(reported as issue #2086639) was never patched anyway. Removed trailing
spaces. Split into subheaders. Added `rustfmt` link. Removed spurious
backquotes. Reworded contents slightly. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
core:
- Add support for SIOCETHTOOL ETHTOOL_GET_TS_INFO
- Separate CIS_LINK and BIS_LINK link types
- Introduce HCI Driver protocol
drivers:
- btintel_pcie: Do not generate coredump for diagnostic events
- btusb: Add HCI Drv commands for configuring altsetting
- btusb: Add RTL8851BE device 0x0bda:0xb850
- btusb: Add new VID/PID 13d3/3584 for MT7922
- btusb: Add new VID/PID 13d3/3630 and 13d3/3613 for MT7925
- btnxpuart: Implement host-wakeup feature
* tag 'for-net-next-2025-05-22' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (23 commits)
Bluetooth: btintel: Check dsbr size from EFI variable
Bluetooth: MGMT: iterate over mesh commands in mgmt_mesh_foreach()
Bluetooth: btusb: Add new VID/PID 13d3/3584 for MT7922
Bluetooth: btusb: use skb_pull to avoid unsafe access in QCA dump handling
Bluetooth: L2CAP: Fix not checking l2cap_chan security level
Bluetooth: separate CIS_LINK and BIS_LINK link types
Bluetooth: btusb: Add new VID/PID 13d3/3630 for MT7925
Bluetooth: add support for SIOCETHTOOL ETHTOOL_GET_TS_INFO
Bluetooth: btintel_pcie: Dump debug registers on error
Bluetooth: ISO: Fix getpeername not returning sockaddr_iso_bc fields
Bluetooth: ISO: Fix not using SID from adv report
Revert "Bluetooth: btusb: add sysfs attribute to control USB alt setting"
Revert "Bluetooth: btusb: Configure altsetting for HCI_USER_CHANNEL"
Bluetooth: btusb: Add HCI Drv commands for configuring altsetting
Bluetooth: Introduce HCI Driver protocol
Bluetooth: btnxpuart: Implement host-wakeup feature
dt-bindings: net: bluetooth: nxp: Add support for host-wakeup
Bluetooth: btusb: Add RTL8851BE device 0x0bda:0xb850
Bluetooth: hci_uart: Remove unnecessary NULL check before release_firmware()
Bluetooth: btmtksdio: Fix wakeup source leaks on device unbind
...
====================
Link: https://patch.msgid.link/20250522171048.3307873-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cpu controller interface files account for or affect processes
differently based on their scheduling policy, and the underlying
scheduler used (fair-class vs. BPF scheduler). Document these
differences
Signed-off-by: Shashank Balaji <shashank.mahadasyam@sony.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Mentions of CFS are stale since the fair-class scheduler is implemented using
EEVDF. So, convert such mentions to "fair-class scheduler" to stay
algorithm-name agnostic.
Signed-off-by: Shashank Balaji <shashank.mahadasyam@sony.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The paragraphs on cpu.uclamp.{min,max} are space indented. Convert them to
tab indentation to make them uniform with the other paragraphs.
Signed-off-by: Shashank Balaji <shashank.mahadasyam@sony.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ASoC: Updates for v6.16
The changes in this release are quite large, mainly in drivers rather
than the core. This is partly due to cleanups that touch a lot of
drivers and partly due to several relatively large new drivers.
- Support for automatically enumerating DAIs from standards conforming
SoundWire SDCA devices, further work is required for these to be
useful in an actual card.
- Conversion of quite a few drivers to newer GPIO APIs.
- More helpers and cleanups from Mormimoto-san.
- Support for a wider range of AVS platforms.
- Support for AMD ACP 7.x platforms, Cirrus Logic CS35L63 and CS48L32,
Everest Semiconductor ES8389, Longsoon-1 AC'97 controllers, nVidia
Tegra264, Richtek ALC203 and RT9123 and Rockchip SAI controllers.
Georgi writes:
interconnect changes for 6.16
This pull request contains the interconnect changes for the 6.16-rc1
merge window. The core and driver changes are listed below.
Core changes:
- Add support for dynamic id allocation, that allows creating
multiple instances of the same provider
Driver changes:
- Add driver for the EPSS L3 instances on SA8775P SoC
- Add QoS support for SM8650 SoC
- Add some missing nodes for SM8650
- Misc dt-binding style and indentation fixes
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.16-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sm8650: remove regmap config for mc_virt & clk_virt
interconnect: qcom: sm8650: add the MASTER_APSS_NOC
dt-bindings: interconnect: sm8650: document the MASTER_APSS_NOC
interconnect: qcom: sm8650: enable QoS configuration
dt-bindings: interconnect: Correct indentation and style in DTS example
interconnect: qcom: sa8775p: Add dynamic icc node id support
interconnect: qcom: icc-rpmh: Add dynamic icc node id support
interconnect: qcom: Add multidev EPSS L3 support
interconnect: core: Add dynamic id allocation support
dt-bindings: interconnect: Add EPSS L3 compatible for SA8775P
Pull networking fixes from Paolo Abeni:
"This is somewhat larger than what I hoped for, with a few PRs from
subsystems and follow-ups for the recent netdev locking changes,
anyhow there are no known pending regressions.
Including fixes from bluetooth, ipsec and CAN.
Current release - regressions:
- eth: team: grab team lock during team_change_rx_flags
- eth: bnxt_en: fix netdev locking in ULP IRQ functions
Current release - new code bugs:
- xfrm: ipcomp: fix truesize computation on receive
- eth: airoha: fix page recycling in airoha_qdma_rx_process()
Previous releases - regressions:
- sched: hfsc: fix qlen accounting bug when using peek in
hfsc_enqueue()
- mr: consolidate the ipmr_can_free_table() checks.
- bridge: netfilter: fix forwarding of fragmented packets
- xsk: bring back busy polling support in XDP_COPY
- can:
- add missing rcu read protection for procfs content
- kvaser_pciefd: force IRQ edge in case of nested IRQ
Previous releases - always broken:
- xfrm: espintcp: remove encap socket caching to avoid reference leak
- bluetooth: use skb_pull to avoid unsafe access in QCA dump handling
- eth: idpf:
- fix null-ptr-deref in idpf_features_check
- fix idpf_vport_splitq_napi_poll()
- eth: hibmcge: fix wrong ndo.open() after reset fail issue"
* tag 'net-6.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (40 commits)
octeontx2-af: Fix APR entry mapping based on APR_LMT_CFG
octeontx2-af: Set LMT_ENA bit for APR table entries
net/tipc: fix slab-use-after-free Read in tipc_aead_encrypt_done
octeontx2-pf: Avoid adding dcbnl_ops for LBK and SDP vf
selftests/tc-testing: Add an HFSC qlen accounting test
sch_hfsc: Fix qlen accounting bug when using peek in hfsc_enqueue()
idpf: fix idpf_vport_splitq_napi_poll()
net: hibmcge: fix wrong ndo.open() after reset fail issue.
net: hibmcge: fix incorrect statistics update issue
xsk: Bring back busy polling support in XDP_COPY
can: slcan: allow reception of short error messages
net: lan743x: Restore SGMII CTRL register on resume
bnxt_en: Fix netdev locking in ULP IRQ functions
MAINTAINERS: Drop myself to reviewer for ravb driver
net: dwmac-sun8i: Use parsed internal PHY address instead of 1
net: ethernet: ti: am65-cpsw: Lower random mac address error print to info
can: kvaser_pciefd: Continue parsing DMA buf after dropped RX
can: kvaser_pciefd: Fix echo_skb race
can: kvaser_pciefd: Force IRQ edge in case of nested IRQ
idpf: fix null-ptr-deref in idpf_features_check
...
Suzuki writes:
coresight: updates for Linux v6.16
CoreSight self-hosted trace driver subsystem updates for Linux v6.16 includes:
- Clear CLAIM tags on device probe if self-hosted tags are set.
- Support for perf AUX pause/resume for CoreSight ETM PMU driver, with trace
collection at pause.
- Miscellaneous fixes for the subsystem
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
* tag 'coresight-next-v6.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/coresight/linux: (27 commits)
coresight: prevent deactivate active config while enabling the config
coresight: holding cscfg_csdev_lock while removing cscfg from csdev
coresight/etm4: fix missing disable active config
coresight: etm4x: Fix timestamp bit field handling
coresight: tmc: fix failure to disable/enable ETF after reading
Documentation: coresight: Document AUX pause and resume
coresight: perf: Update buffer on AUX pause
coresight: tmc: Re-enable sink after buffer update
coresight: perf: Support AUX trace pause and resume
coresight: etm4x: Hook pause and resume callbacks
coresight: Introduce pause and resume APIs for source
coresight: etm4x: Extract the trace unit controlling
coresight: cti: Replace inclusion by struct fwnode_handle forward declaration
coresight: Disable MMIO logging for coresight stm driver
coresight: replicator: Fix panic for clearing claim tag
coresight: Add a KUnit test for coresight_find_default_sink()
coresight: Remove extern from function declarations
coresight: Remove inlines from static function definitions
coresight: Clear self hosted claim tag on probe
coresight: etm3x: Convert raw base pointer to struct coresight access
...
Jonathan writes:
IIO: New device support, features and cleanup for 6.16 - take 2
Note - last minute rebase was to drop a typo patch that I'd accidentally
picked up (in the microblaze arch Kconfig)
Take 2 is due to that rebase messing up some fixes tags that were
referring to patches after that point.
There is a known merge conflict due to changes in neighbouring lines.
Stephen's resolution in linux-next is:
https://lore.kernel.org/linux-next/20250506155728.65605bae@canb.auug.org.au/
Added 3 named IIO reviewers to MAINTAINERS. This is a reflection of those
who have been doing much of this work for some time. Lars-Peter is
removed from the entry having moved on to other topics. Thanks
Nuno, David and Andy for stepping up and Lars-Peter for all your
hard work in the past!
Includes the usual mix of new device support, features and general
cleanup.
This time we also have some tree wide changes.
- Rip out the iio_device_claim_direct_scoped() as it proved hard to work
with. This series includes quite a few related cleanups such as use
of guard or factoring code out to allow direct returns.
- Switch from iio_device_claim/release_direct_mode() to new
iio_device_claim/release_direct() which is structured so that sparse
can warn on failed releases. There were a few false positives but
those were mostly in code that benefited from being cleaned up as part
of this process.
- Introduce iio_push_to_buffers_with_ts() to replace the _timestamp()
version over time. This version takes the size of the supplied buffer
which the core checks is at least as big as expected by calculation
from channel descriptions of those channels enabled. Use this in
an initial set of drivers.
- Add macros for IIO_DECLARE_BUFFER_WITH_TS() and
IIO_DECLARE_DMA_BUFFER_WITH_TS() to avoid lots of fiddly code to ensure
correctly aligned buffers for timestamps being added onto the end of
channel data.
New device support
------------------
adi,ad3530r
- New driver for AD3530, AD3530R, AD3531 and AD3531R DACs with
programmable gain controls. R variants have internal references.
adi,ad7476
- Add support (dt compatible only) for the Rohm BU79100G ADC which is
fully compatible with the ti,ads7866.
adi,ad7606
- Support ad7606c-16 and ad7606c-18 devices. Includes switch to dynamic
channel information allocation.
adi,ad7380
- Add support for the AD7389-4
dfrobot,sen0322
- New driver for this oxygen sensor.
mediatek,mt2701-auxadc
- Add binding for MT6893 which is fully compatible with already supported
MT8173.
meson-saradc
- Support the GXLX SoCs. Mostly this is a workaround for some unrelated
clock control bits found in the ADC register map.
nuvoton,nct7201
- New driver for NCT7201 and NCT7202 I2C ADCs.
rohm,bd79124
- New driver for this 12-bit, 8-channel SAR ADC.
- Switch to new set_rv etc gpio callbacks that were added in 6.15.
rohm,bd79703
- Add support for BD79700, BD79701 and BD79702 DACs that have subsets of
functionality of the already supported bd79703. Included making this
driver suitable for support device variants.
st,stm32-lptimer
- Add support for stm32pm25 to this trigger.
Features
--------
Beyond IIO
- Property iterator for named children.
core
- Enable writes for 64 bit integers used for standard IIO ABI elements.
Previously these could be read only.
- Helper library that should avoid code duplication for simpler ADC
bindings that have a child node per channel.
- Enforce that IIO_DMA_MINALIGN is always at least 8 (almost always true
and simplifies code on all significant architectures)
core/backend
- Add support to control source of data - useful when the HDL includes
things like generated ramps for testing purposes. Enable this for
adi-axi-dac
adi,ad3552-hs
- Add debugfs related callbacks to allow debug access to register contents.
adi,ad4000
- Support SPI offload with appropriate FPGA firmware along with improving
documentation.
adi,ad7293
- Add support for external reference voltage.
adi,ad7606
- Support SPI offload.
adi,ad7768-1
- Support reset GPIO.
adi,admv8818
- Support filter frequencies beyond 2^32.
adi,adxl345
- Add single and double tap events.
hid-sensor-prox
- Support 16-bit report sizes as seen on some Intel platforms.
invensense,icm42600
- Enable use of named interrupts to avoid problems with some wiring choices.
Get the interrupt by name, but fallback to previous assumption on the first
being INT1 if no names are supplied.
microchip,mcp3911
- Add reset gpio support.
rohm,bh7150
- Add reset gpio support.
st,stm32
- Add support to control oversampling.
ti,adc128s052
- Add support for ROHM BD79104 which is early compatible with the TI
parts already supported by this driver. Includes some general driver
cleanup and a separate dt binding.
- Simplify reference voltage handling by assuming it is fixed after enabling
the supply.
winsen,mhz19b
- New driver for this C02 sensor.
Cleanup and minor fixes
-----------------------
dt-bindings
- Correct indentation and style for DTS examples.
- Use unevalutateProperties for SPI devices instead of additionalProperties
to allow generic SPI properties from spi-peripheral-props.yaml
ABI Docs
- Add missing docs for sampling_frequency when it applies only to events.
Treewide
- Various minor tweaks, comment fixes and similar.
- Sort TI ADCs in Kconfig that had gotten out of order.
- Switch various drives that provide GPIO chip functionality to the new
callbacks with return values.
- Standardize on { } formatting for all array sentinels.
- Make use of aligned_s64 in a few places to replace either wrong types
or manually defined equivalents.
- Drop places where spi bits_per_word is set to 8 because that is the
default anyway.
adi,ad_sigma_delta library
- Avoid a potential use of uninitialized data if reg_size has a value
that is not supported (no drivers hit this but it is reasonable hardening)
adi,ad4030
- Add error checking for scan types and no longer store it in state.
- Rework code to reduce duplication.
- Move setting the mode from buffer preenable() to update_scan_mode(),
better matching expected semantics of the two different callbacks.
- Improve data marshalling comments.
adi,ad4695
- Use u16 for buffer elements as oversampling is not yet supported except
with SPI offload (which doesn't use this path).
adi,ad5592r
- Clean up destruction of mutexes.
- Use lock guards to simplify code (later patch fixes a missed unlock)
adi,ad5933
- Correct some incorrect settling times.
adi,ad7091
- Deduplicate handling of writable vs volatile registers as they are the
inverse of each other for this device.
adi,ad7124
- Fix 3db Filter frequency.
- Remove ability to directly write the filter frequency (which was broken)
- Register naming improvements.
adi,ad7606
- Add a missing return value check.
- Fill in max sampling rates for all chips.
- Use devm_mutex_init()
- Fix up some kernel-doc formatting issues.
- Remove some camel case that snuck in.
- Drop setting address field in channels as easily established from other
fields.
- Drop unnecessary parameter to ad76060_scale_setup_cb_t.
adi,ad7768-1
- Convert to regmap.
- Factor out buffer allocation.
- Tidy up headers.
adi,ad7944
- Stop setting bits_per_word in SPI xfers with no data.
adi,ad9832
- Add of_device_id table rather than just relying on fallbacks.
- Use FIELD_PREP() to set values of fields.
adi,admv1013
- Cleanup a pointless ternary.
adi,admv8818
- Fix up LPF Band 5 frequency which was slightly wrong.
- Fix an integer overflow.
- Fix range calculation
adi,adt7316
- Replace irqd_get_trigger_type(irq_get_irq_data()) with simpler
irq_get_trigger_type()
adi,adxl345
- Use regmap cache instead of various state variables that were there to
reduce bus accesses.
- Make regmap return value checking consistent across all call sites.
adi,axi-dac
- Add a check on number of channels (0 to 15 valid)
allwinner,sun20i
- Use new adc-helpers to replace local parsing code for channel nodes.
bosch,bmp290
- Move to local variables for sensor data marshalling removing the need
for a messy definition that has to work for all supported parts.
Follow up fix adds a missing initialization.
dynaimage,al3010 and dynaimage,al3320a
- Various minor cleanup to bring these drivers inline with reviewed feedback
given on a new driver.
- Fix an error path in which power down is not called when it should be.
- Switch to regmap.
google,cros_ec
- Fix up a flexible array in middle of structure warning.
- Flush fifo when changing the timeout to avoid potential long wait
for samples.
hid-sensor-rotation
- Remove an __aligned(16) marking that doesn't seem to be justified.
kionix,kxcjk-1013
- Deduplicate code for setting up interrupts.
microchip,mcp3911
- Fix handling of conversion results register which differs across supported
devices.
idt,zopt2201
- Avoid duplicating register lists as all volatile registers are the
inverse of writeable registers on this device.
renesas,rzg2l
- Use new adc-helpers to replace local parsing code for channel nodes.
ti,ads1298
- Fix a missing Kconfig dependency.
* tag 'iio-for-6.16a-take2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (260 commits)
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
iio: pressure: zpa2326_spi: remove bits_per_word = 8
iio: pressure: ms5611_spi: remove bits_per_word = 8
...
Merge series from "Sheetal ." <sheetal@nvidia.com>:
The patch series includes the necessary changes to enable
support for the Tegra264 platforms in AHUB drivers.
Multi-PTP source support within a network topology has been merged,
but the hardware timestamp source is not yet exposed to users.
Currently, users only see the PTP index, which does not indicate
whether the timestamp comes from a PHY or a MAC.
Add support for reporting the hwtstamp source using a
hwtstamp-source field, alongside hwtstamp-phyindex, to describe
the origin of the hardware timestamp.
Remove HWTSTAMP_SOURCE_UNSPEC enum value as it is not used at all.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250519-feature_ptp_source-v4-1-5d10e19a0265@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert cdn-dp-rockchip.txt to yaml.
Add new "port@1" property which represents the CDN DP output to keep
the same style as the other display interfaces.
This patch also changes the constraints for "phys" and "extcon". For
the original binding, only one phy and the corresponding extcon can
be specified. In the new binding, one or two phys can be specified.
Since the RK3399 has two DP-USB PHYs, specifying one allows output
via the corresponding PHY, while specifying two lets the driver
choose one PHY for output. This rule also applies to extcon, which
provides the cable state for the corresponding PHY.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250520024718.142-3-kernel@airkyi.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Add Tegra264 compatible strings to APE subsystem device bindings:
- audio-graph-card: Due to different PLL clock rate.
- admaif: Due to 32 channels supported and register offset changes.
- i2s: Due to 32 channels supported and register offset changes.
- amx/adx: Due to 32 channels supported and register offset changes.
- asrc: Due to different ARAM address.
- ahub: Due to AHUB IPs number of instances updates.
- for future proofing the T264 compatibility is added for other device
nodes.
These bindings enable the enhanced audio features of Tegra264
while maintaining compatibility with existing platforms.
Signed-off-by: Sheetal <sheetal@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250512051747.1026770-3-sheetal@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add optional interconnect and iommu properties to admaif yaml. These
properties are supported from Tegra186 SoC onwards.
This fixes below dtbs_check error for Tegra194 and Tegra234:
'interconnect-names', 'interconnects', 'iommus' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Sheetal <sheetal@nvidia.com>
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://patch.msgid.link/20250512051747.1026770-2-sheetal@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert devicetree bindings for the Broadcom BCM59056 PMU MFD from
TXT to YAML format. This patch does not change any functionality;
the bindings remain the same.
The bindings have been split into two parts: the MFD binding and
a separate binding for the regulator node, to simplify the addition
of other models later (which have different regulators).
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Link: https://lore.kernel.org/r/20250515-bcm59054-v9-1-14ba0ea2ea5b@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
When attempting to use an archive file, such as APEX on android,
as a file-backed mount source, it fails because EROFS image within
the archive file does not start at offset 0. As a result, a loop
or a dm device is still needed to attach the image file at an
appropriate offset first. Similarly, if an EROFS image within a
block device does not start at offset 0, it cannot be mounted
directly either.
To address this issue, this patch adds a new mount option `fsoffset=x'
to accept a start offset for the primary device. The offset should be
aligned to the block size. EROFS will add this offset before performing
read requests.
Signed-off-by: Sheng Yong <shengyong1@xiaomi.com>
Signed-off-by: Wang Shuai <wangshuai12@xiaomi.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250517090544.2687651-1-shengyong1@xiaomi.com
[ Gao Xiang: minor update on documentation and the error message. ]
Reviewed-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
This is [1/3] part of hinic3 Ethernet driver initial submission.
With this patch hinic3 is a valid kernel module but non-functional
driver.
The driver parts contained in this patch:
Module initialization.
PCI driver registration but with empty id_table.
Auxiliary driver registration.
Net device_ops registration but open/stop are empty stubs.
tx/rx logic.
All major data structures of the driver are fully introduced with the
code that uses them but without their initialization code that requires
management interface with the hw.
Co-developed-by: Xin Guo <guoxin09@huawei.com>
Signed-off-by: Xin Guo <guoxin09@huawei.com>
Signed-off-by: Fan Gong <gongfan1@huawei.com>
Co-developed-by: Gur Stavi <gur.stavi@huawei.com>
Signed-off-by: Gur Stavi <gur.stavi@huawei.com>
Link: https://patch.msgid.link/76a137ffdfe115c737c2c224f0c93b60ba53cc16.1747736586.git.gur.stavi@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
People have been asking to see the plan for this, so -
bcachefs has various background tasks that need to be scheduled to
balance efficiency, predictability of performance, etc.
The design and philosophy hasn't changed too much since bcache, which
was primarily designed for server usage, with sustained load in mind.
These days we're seeing more desktop usage - where we really want to let
the system idle effictively, to reduce total power usage - while also
still balancing previous concerns, we still want to let work accumulate
to a degree.
This lays out all the requirements and starts to sketch out the
algorithm I have in mind.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Add Aeonsemi PHYs and the requirement of a firmware to correctly work.
Also document the max number of LEDs supported and what PHY ID expose
when no firmware is loaded.
Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1,
AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1,
AS21210PB1 that all register with the PHY ID 0x7500 0x9410 on C45
registers before the firmware is loaded.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-7-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
More Qualcomm Arm64 DeviceTree updates for v6.16
Support for CPU frequency scaling is enabled on the X Elite platform.
Also on X Elite, support for the HP EliteBook Ultra G1q is introduced.
Support for the QCS6490 RB3gen2 Industrial Mezzanine is also added.
PCIe controllers and PHYs are described and enabled across IPQ5018,
IPQ5332, and IPQ5424. On IPQ9474 the missing MHI register range is
added. The TCSR block is described and used to enable download mode
flags on IPQ5018.
The venus video encoder/decoder is enabled on the MSM8998-based Lenovo
Miix 630 laptop.
The crypto engine is enabled on QCM2290 and QCS615. Bluetooth is enabled
on the QCM2210-based RB1 board.
The Fairphone FP5 gains Displayport sound support.
SAR2130P display nodes are added.
On 8cx Gen3 the sensor remoteproc (SLPI) is introduced and this is
enabled on Lenovo Thinkpad X13s and the CRD.
The SDM845-based Samsung Galaxy S9 gains graphics, modem and initial
sound support.
On SDX75 the QPIC BAM and NAND support is added, and these are enabled
on the IDP board.
LLCC is added for SM8750. SM8550 gains Iris video decoder support.
For X Elite, Lenovo ThinkPad T14s support for the SDX62 modem, as well
as audio headset, is added. ASUS Vivobook S 15 gains Bluetooth support,
Microsoft Surface Laptop 7 models gets support for DP over USB Type-C,
HP Omnibook X 14 gains audio support. The devkit gets the USB multiport
controller and the two USB Type-A ports described.
Additionally a variety of Devicetree fixes are introduced, primarily
identified through binding validation.
* tag 'qcom-arm64-for-6.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (58 commits)
arm64: dts: qcom: sm4450: Add RPMh power domains support
arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: add retimers, dp altmode support
arm64: dts: qcom: ipq5424: Enable PCIe PHYs and controllers
arm64: dts: qcom: ipq5424: Add PCIe PHYs and controller nodes
arm64: dts: qcom: sc7280: Mark FastRPC context banks as dma-coherent
arm64: dts: qcom: sdx75-idp: Enable QPIC BAM & QPIC NAND support
arm64: dts: qcom: sdx75: Add QPIC NAND support
arm64: dts: qcom: sdx75: Add QPIC BAM support
arm64: dts: qcom: qcm2290: Add crypto engine
arm64: dts: qcom: x1e80100-vivobook-s15: Add bluetooth
arm64: dts: qcom: x1e80100: Add PCIe lane equalization preset properties
arm64: dts: qcom: qcs615: Fix up UFS clocks
arm64: dts: qcom: sa8775p: Clean up the PSCI PDs
arm64: dts: qcom: msm8996-oneplus: Add SLPI VDD_PX
arm64: dts: qcom: sm6350-pdx213: Wire up USB regulators
arm64: dts: qcom: msm8998-yoshino: Add QUSB2PHY VDD supply
arm64: dts: qcom: msm8998-mtp: Add QUSB2PHY VDD supply
arm64: dts: qcom: msm8998-fxtec: Add QUSB2PHY VDD supply
arm64: dts: qcom: qcs615: Remove disallowed property from AOSS_QMP node
arm64: dts: qcom: msm8998: Remove mdss_hdmi_phy phandle argument
...
Link: https://lore.kernel.org/r/20250520024248.38904-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New SoC the RK3562 (4xA53, Mali-G52) with one evaluation board.
New boards:
- Cobra and PP1516 from Theobroma-Systems (build around the PX30)
- Radxa Rock 5B+ (rk3588)
- Rockchip RK3399 industrial eval board
New peripherals:
- GMAC + SDMMC/SDIO on rk3528
- SAI + HDMI-audio on rk3576
Interesting general updates:
- move rk3528 i2c + uart aliases as requested
- rk3568 PCIe3 MSI to use GIC ITS
- update deprecated dwmac reset properties on some px30 boards
- updates for cypress usb hubs on some Theobroma boards
Binding taken with Greg's blessing
https://lore.kernel.org/all/2025051550-polish-prude-ed56@gregkh/
* tag 'v6.16-rockchip-dts64-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (35 commits)
arm64: dts: rockchip: Improve LED config for NanoPi R5S
arm64: dts: rockchip: add px30-pp1516 base dtsi and board variants
dt-bindings: arm: rockchip: add PX30-PP1516 boards from Theobroma Systems
arm64: dts: rockchip: add px30-cobra base dtsi and board variants
dt-bindings: arm: rockchip: add PX30-Cobra boards from Theobroma Systems
arm64: dts: rockchip: move reset to dedicated eth-phy node on ringneck
arm64: dts: rockchip: add basic mdio node to px30
arm64: dts: rockchip: disable unrouted USB controllers and PHY on RK3399 Puma with Haikou
arm64: dts: rockchip: disable unrouted USB controllers and PHY on RK3399 Puma
arm64: dts: rockchip: fix internal USB hub instability on RK3399 Puma
dt-bindings: usb: cypress,hx3: Add support for all variants
arm64: dts: rockchip: move rk3528 i2c+uart aliases to board files
arm64: dts: rockchip: drop wrong spdif clock from edp1 on rk3588
arm64: dts: rockchip: Add RK3562 evb2 devicetree
arm64: dts: rockchip: add core dtsi for RK3562 SoC
dt-bindings: arm: rockchip: Add rk3562 evb2 board
dt-bindings: soc: rockchip: Add rk3562 syscon compatibles
dt-bindings: rockchip: pmu: Add rk3562 compatible
arm64: dts: rockchip: Enable Ethernet controller on Radxa E20C
arm64: dts: rockchip: Add GMAC nodes for RK3528
...
Link: https://lore.kernel.org/r/3998939.iIbC2pHGDl@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner device tree changes for 6.16
Introduce Allwinner A523 / A527 / T527 SoC family w/ three new devices:
- Radxa Cubie A5E
- X96Q-Pro+
- Avaota-A1
Also enable EMAC0 ethernet MAC on A523 family for Cubie A5E & Avaota-A1.
Note: the SoC has two different ethernet controllers.
Changes to existing SoCs:
- Enable GPU on H616 with all boards enabled
- Set maximum MMC frequency for the A100
Changes to existing boards:
- Add WiFi/BT header on PINE64 A64 boards
- Add hp-det-gpios for Anbernic RG35XX
- Add support for PHY LEDs on Bananapi (the original one)
Add new devices for existing SoCs:
- YuzukiHD Chameleon based on H6
- Liontron H-A133L based on A133 (compatible with A100)
Tree wide cleanups:
- Use preferred node names for cooling maps
- Align wifi node name with bindings
- Drop spurious 'clock-latency-ns' properties for H5 & H6
* tag 'sunxi-dt-for-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (27 commits)
arm64: dts: allwinner: a100: add Liontron H-A133L board support
dt-bindings: arm: sunxi: Add Liontron H-A133L board name
dt-bindings: vendor-prefixes: Add Liontron name
ARM: dts: bananapi: add support for PHY LEDs
arm64: dts: allwinner: a100: set maximum MMC frequency
arm64: dts: allwinner: t527: add EMAC0 to Avaota-A1 board
arm64: dts: allwinner: a527: add EMAC0 to Radxa A5E board
arm64: dts: allwinner: a523: Add EMAC0 ethernet MAC
dt-bindings: sram: sunxi-sram: Add A523 compatible
arm64: dts: allwinner: a64: Add WiFi/BT header on SOPINE Baseboard
arm64: dts: allwinner: a64: Add WiFi/BT header on PINE A64
arm64: dts: allwinner: correct the model name for Radxa Cubie A5E
ARM: dts: allwinner: Align wifi node name with bindings
arm64: dts: allwinner: Align wifi node name with bindings
arm64: dts: allwinner: h616: enable Mali GPU for all boards
arm64: dts: allwinner: h616: Add Mali GPU node
arm64: dts: allwinner: h700: Add hp-det-gpios for Anbernic RG35XX
arm64: dts: allwinner: h5/h6: Drop spurious 'clock-latency-ns' properties
arm/arm64: dts: allwinner: Use preferred node names for cooling maps
arm64: dts: allwinner: h616: add YuzukiHD Chameleon support
...
Link: https://lore.kernel.org/r/aCaeZJ2t4S_xhgjp@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT for v6.16, round 1
Highlights:
----------
- MCU:
- Add low power timer on STM32F746
- Add STM32H747 High end MCU support. It embeds:
- dual-core (Cortex-M7 + Cortex-M4)
- up to 2 Mbytes flash
- 1 Mbyte of internal RAM
- Add STM32H747i-disco board support. Detailed information can be
found at:
https://www.st.com/en/evaluation-tools/stm32h747i-disco.html
- MPU:
- STM32MP13:
- Add VREFINT calibration support based on ADC.
- STMP32MP15:
- Add new Ultratronik Fly board support:
- based on STM32MP157C SoC
- 1GB of DDR3
- Several connections are available on this boards:
2*USB2.0, 1*USB2.0 MiniUSB, Debug UART, 1*UART, 1*USART,
SDcard, RJ45, ...
- STM32MP25:
- Add OCTOSPI support on STM32MP25 SoCs
- Add SPI NOR flash support on STM32MP257F-EV1 connected to OSPI1
- Add Low power timer TIMER (LPTIM) on STM32MP25 SoCs and use
LPTIM3 as low power broadcast timer on STM32MP257F-EV1.
* tag 'stm32-dt-for-v6.16-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (22 commits)
ARM: dts: stm32: add initial support for stm32mp157-ultra-fly-sbc board
MAINTAINERS: Add entry for ULTRATRONIK BOARD SUPPORT
dt-bindings: arm: stm32: Document Ultratronik's Fly board DT binding
dt-bindings: vendor-prefixes: Add Ultratronik
arm64: dts: st: use lptimer3 as tick broadcast source on stm32mp257f-ev1
arm64: dts: st: add low-power timer nodes on stm32mp251
arm64: defconfig: enable STM32 LP timer clockevent driver
arm64: dts: st: Add SPI NOR flash support on stm32mp257f-ev1 board
arm64: dts: st: Add ospi port1 pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: dts: st: Add OMM node on stm32mp251
ARM: dts: stm32: support STM32h747i-disco board
ARM: dts: stm32: add an extra pin map for USART1 on stm32h743
ARM: dts: stm32: add pin map for UART8 controller on stm32h743
ARM: dts: stm32: add uart8 node for stm32h743 MCU
dt-bindings: clock: stm32h7: rename USART{7,8}_CK to UART{7,8}_CK
ARM: stm32: add a new SoC - STM32H747
dt-bindings: arm: stm32: add compatible for stm32h747i-disco board
ARM: dts: stm32h7-pinctrl: add _a suffix to u[s]art_pins phandles
ARM: dts: st: stm32: Align wifi node name with bindings
ARM: dts: stm32: add low power timer on STM32F746
...
Link: https://lore.kernel.org/r/2f101efb-6d58-48d8-983a-57e30a34827c@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm Arm64 DeviceTree updates for v6.16
The Snapdragon X Plus platform and related reference device is
introduced. Devicetree for the Xiaomi Redmi Note 8 is added.
Tsens and thermal zones are added for IPQ5332 and IPQ5424. IPQ6018 gains
1.2GHz and 1.5GHz CPU frequencies. The IPQ5424 gains MMC, LEDs and
buttons, while the IPQ9574 gains NSS clock controller and SPI NAND
support.
IPQ6018 SMEM is transitioned to be described directly in the
reserved-memory node.
Display and GPU are enabled in the QCM6490-based Fairphone FP5. On
QCS6490 Rb3Gen2 ADC channels for thermal profiling are added and
Bluetooth is enabled. The USB Type-C orientation GPIO is added on the
QCS6490 Rb3Gen2 and the vision mezzanine is described.
The Fairphone FP5 gains touchscreen and USB Type-C display support, and
the QCM6490 IDP board gains a required listed of protected clocks.
The camera subsystem in SC7280 is described and UFS is transitioned to
use operating points.
On MSM8916, MSM8919 and MSM8939, and devices on these platforms, the
UART pinctrl state is cleaned up.
The MSM8953 platform gains another UART and interconnects.
On SA8775P CTCU and ETR nodes are added, and the CPUfreq throttling
interrupts are added.
Samsung Galaxy S9 SM-G9600 gains a description of the MAX77705 used for
charging, fuel gauge, haptic, and LED, as well as the PMIC used for
display and touchscreen, which then is used to enable the touchscreen.
The LPG/PWM node is added to PM8937 and Xiaomi Redmi 5A gains display
backlight control.
Display and GPU are enabled for the Nothing Phone (1).
QCS615 platform gains command DB definition.
The QCS8300 platform gains description of more QUP instances, CPUfreq,
PCIe SMMU and the SPMI controller.
On SAR2130P PCIe EP device nodes are added.
On SDM630 missing resets are added for SDCC. Then on Fairphone FP3 modem
is enabled, and firmware-path are defined on ADSP and WCNSS.
The SDM845 RB3/DragonBoard845c and the QRB5165 RB5 has the sensors DSP
enabled, and the vision mezzanine on both gets their CMA configuration
cleaned up. Xiaomi Pocophone F1 gains touchscreen support.
On the SM7325 Nothing Phone (1), display, GPU, and camera EEPROMs are
described.
On SM8450 the PCIe endpoint controller is described.
For SM8550 OPP tables are described for PCIe and QUP. SM8750 gains RPMh
sleep stats.
SM8650 gians OSM L3 scaling and variety of OPP tables and missing
interconnect definitions. The thermal trip points for CPU cores and GPU
are raised in reliance on hardware throttling.
SM8650 is also transitioned to per-CPU interrupt partitions, in order to
properly describe the PMU interrupts. Missing Coresight ETE instances
are added.
On SM8750 the cluster idle states are corrected, then audio and compute
DSPs are introduced, together with the crypto and rng blocks. Modem
support is added and enabled on MTP and QRD devices.
On SC8280XP overlays are introduced for those running Linux at EL2 on
these devices. A few more temp-alarm instances are added for the PMICs.
On the X Elite platform GPU cooling and watchdog is introduced, together
with a number of smaller fixes. Dell XPS13 gains support for USB Type-C
display, the QCP gains WiFi/BT power sequence, and a few devices learns
about HBR3. The RTC support is enabled and regulators that are feeding
resources that should be always on is marked as such on a variety of
boards.
The Lenovo Thinkpad T14s DeviceTree is split in two, in order to
describe the LCD and OLED variants.
Missing properties for the crypto BAM is introduced on a variety of
platforms, taking care of a long standing error message in the kernel
log during boot.
DSI phy clock ids are transitioned to use identifiers from the PHY
header file and VBIF region size is corrected, across a large number of
platforms.
A couple of DWC3 quirks are added across a lot of platforms.
The arm32-for-6.15 pull request was accidentally merged into the
arm64-for-6.16 branch and this wasn't discovered until a significant
number of commits would have to be rebased. As such this is kept here as
well.
* tag 'qcom-arm64-for-6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (308 commits)
arm64: dts: qcom: sdm845-xiaomi-beryllium-ebbg: introduce touchscreen support
arm64: dts: qcom: sdm845-xiaomi-beryllium-tianma: introduce touchscreen support
arm64: dts: qcom: sdm845-xiaomi-beryllium-common: add touchscreen related nodes
arm64: dts: qcom: qcs8300: add the pcie smmu node
arm64: dts: qcom: x1e80100-*: Drop useless DP3 compatible override
arm64: dts: qcom: msm8953: Add interconnects
arm64: dts: qcom: msm8953: Add uart_5
arm64: dts: qcom: sm8350: Use q6asm defines for reg
arm64: dts: qcom: sm7325-nothing-spacewar: Use q6asm defines for reg
arm64: dts: qcom: sdm850*: Use q6asm defines for reg
arm64: dts: qcom: sdm845*: Use q6asm defines for reg
arm64: dts: qcom: sc7280: Use q6asm defines for reg
arm64: dts: qcom: sc7180-acer-aspire1: Use q6asm defines for reg
arm64: dts: qcom: qrb5165-rb5: Use q6asm defines for reg
arm64: dts: qcom: msm8996*: Use q6asm defines for reg
arm64: dts: qcom: msm8953: Use q6asm defines for reg
arm64: dts: qcom: msm8916-modem-qdsp6: Use q6asm defines for reg
arm64: dts: qcom: apq8096-db820c: Use q6asm defines for reg
arm64: dts: qcom: qcm6490-fairphone-fp5: Hook up DisplayPort over USB-C
arm64: dts: qcom: qcm6490-fairphone-fp5: Add OCP96011 audio switch
...
Link: https://lore.kernel.org/r/20250511235241.15192-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
More Qualcomm driver updates for v6.16
Allow HP EliteBook Ultra G1q to use QSSECOM for UEFI variable acecss.
Add missing compatible for IPQ5018 TCSR block. Fix a kernel-doc warning
in SCM driver.
* tag 'qcom-drivers-for-6.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
docs: firmware: qcom_scm: Fix kernel-doc warning
firmware: qcom: scm: Allow QSEECOM for HP EliteBook Ultra G1q
dt-bindings: mfd: qcom,tcsr: Add compatible for ipq5018
Link: https://lore.kernel.org/r/20250520024916.39712-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RISC-V cache drivers for v6.16
SiFive:
Add support for the Eswin EIC7700 SoC, which needs to make sure of the
non-standard cache-ops provided by the ccache driver.
Bindings:
Conversions for two Marvell bindings to yaml, and additions of two
soc-specific compatibles to the axm45mp bindings.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-cache-for-v6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
dt-bindings: cache: add QiLai compatible to ax45mp
dt-bindings: cache: Convert marvell,tauros2-cache to DT schema
dt-bindings: cache: Convert marvell,{feroceon,kirkwood}-cache to DT schema
dt-bindings: cache: add specific RZ/Five compatible to ax45mp
cache: sifive_ccache: Add ESWIN EIC7700 support
dt-bindings: cache: sifive,ccache0: Add ESWIN EIC7700 SoC compatibility
Link: https://lore.kernel.org/r/20250516-liability-facility-667fc14a2a85@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
