Pull USB fixes from Greg KH:
"Here are some small fixes for 5.3-rc2. All of these resolve some
reported issues, some more than others :)
Included in here is:
- xhci fix for an annoying issue with odd devices
- reversion of some usb251xb patches that should not have been merged
- usb pci quirk additions and fixups
- usb storage fix
- usb host controller error test fix
All of these have been in linux-next with no reported issues"
* tag 'usb-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Fix crash if scatter gather is used with Immediate Data Transfer (IDT).
usb: usb251xb: Reallow swap-dx-lanes to apply to the upstream port
Revert "usb: usb251xb: Add US port lanes inversion property"
Revert "usb: usb251xb: Add US lanes inversion dts-bindings"
usb: wusbcore: fix unbalanced get/put cluster_id
usb/hcd: Fix a NULL vs IS_ERR() bug in usb_hcd_setup_local_mem()
usb-storage: Add a limitation for blk_queue_max_hw_sectors()
usb: pci-quirks: Minor cleanup for AMD PLL quirk
usb: pci-quirks: Correct AMD PLL quirk detection
Pull ARM SoC fixes from Olof Johansson:
"Here's the first batch of fixes for this release cycle.
Main diffstat here is the re-deletion of netx. I messed up and most
likely didn't remove the files from the index when I test-merged this
and saw conflicts, and from there on out 'git rerere' remembered the
mistake and I missed checking it. Here it's done again as expected.
Besides that:
- A defconfig refresh + enabling of new drivers for u8500
- i.MX fixlets for i2c/SAI/pinmux
- sleep.S build fix for Davinci
- Broadcom devicetree build/warning fix"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: defconfig: u8500: Add new drivers
ARM: defconfig: u8500: Refresh defconfig
ARM: dts: bcm: bcm47094: add missing #cells for mdio-bus-mux
ARM: davinci: fix sleep.S build error on ARMv4
arm64: dts: imx8mq: fix SAI compatible
arm64: dts: imx8mm: Correct SAI3 RXC/TXFS pin's mux option #1
ARM: dts: imx6ul: fix clock frequency property name of I2C buses
ARM: Delete netx a second time
ARM: dts: imx7ulp: Fix usb-phy unit address format
If gpiolib is disabled, we use the inline stubs from gpio/consumer.h
instead of regular definitions of GPIO API. The stubs for 'optional'
variants of gpiod_get routines return NULL in this case as if the
relevant GPIO wasn't found. This is correct so far.
Calling other (non-gpio_get) stubs from this header triggers a warning
because the GPIO descriptor couldn't have been requested. The warning
however is unconditional (WARN_ON(1)) and is emitted even if the passed
descriptor pointer is NULL.
We don't want to force the users of 'optional' gpio_get to check the
returned pointer before calling e.g. gpiod_set_value() so let's only
WARN on non-NULL descriptors.
Cc: stable@vger.kernel.org
Reported-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Jonathan writes:
First set of IIO fixes in the 5.3 cycle.
* cros_ec_accel_legacy
- Fix a false double entry for channel scale as both per channel
and shared.
* gyro_adc
- Fix uninitialized return code that got detected by GCC 9.0 having
be previously missed.
* ingenic_adc
- Set the clock divider on probe to avoid an issue seen with false
button press detections on JZ4725B SoCs.
* max9611
- Backwards parameters in GENMASK.
* mpu6050
- Enforce the fact only certain scan modes are actually possible.
One counter fix also picked up for William,
* generic-counter.rst
- Fix some references.
* tag 'iio-fixes-for-5.3a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: gyroadc: fix uninitialized return code
docs: generic-counter.rst: fix broken references for ABI file
iio: imu: mpu6050: add missing available scan masks
iio: cros_ec_accel_legacy: Fix incorrect channel setting
IIO: Ingenic JZ47xx: Set clock divider on probe
iio: adc: max9611: Fix misuse of GENMASK macro
Andrii Nakryiko says:
====================
This patch set makes a number of changes to test_progs selftest, which is
a collection of many other tests (and sometimes sub-tests as well), to provide
better testing experience and allow to start convering many individual test
programs under selftests/bpf into a single and convenient test runner.
Patch #1 fixes issue with Makefile, which makes prog_tests/test.h compiled as
a C code. This fix allows to change how test.h is generated, providing ability
to have more control on what and how tests are run.
Patch #2 changes how test.h is auto-generated, which allows to have test
definitions, instead of just running test functions. This gives ability to do
more complicated test run policies.
Patch #3 adds `-t <test-name>` and `-n <test-num>` selectors to run only
subset of tests.
Patch #4 changes libbpf_set_print() to return previously set print callback,
allowing to temporarily replace current print callback and then set it back.
This is necessary for some tests that want more control over libbpf logging.
Patch #5 sets up and takes over libbpf logging from individual tests to
test_prog runner, adding -vv verbosity to capture debug output from libbpf.
This is useful when debugging failing tests.
Patch #6 furthers test output management and buffers it by default, emitting
log output only if test fails. This give succinct and clean default test
output. It's possible to bypass this behavior with -v flag, which will turn
off test output buffering.
Patch #7 adds support for sub-tests. It also enhances -t and -n selectors to
both support ability to specify sub-test selectors, as well as enhancing
number selector to accept sets of test, instead of just individual test
number.
Patch #8 converts bpf_verif_scale.c test to use sub-test APIs.
Patch #9 converts send_signal.c tests to use sub-test APIs.
v2->v3:
- fix buffered output rare unitialized value bug (Alexei);
- fix buffered output va_list reuse bug (Alexei);
- fix buffered output truncation due to interleaving zero terminators;
v1->v2:
- drop libbpf_swap_print, instead return previous function from
libbpf_set_print (Stanislav);
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Convert send_signal set of tests to be exposed as three sub-tests.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow tests to have their own set of sub-tests. Also add ability to do
test/subtest selection using `-t <test-name>/<subtest-name>` and `-n
<test-nums-set>/<subtest-nums-set>`, as an extension of existing -t/-n
selector options. For the <test-num-set> format: it's a comma-separated
list of either individual test numbers (1-based), or range of test
numbers. E.g., all of the following are valid sets of test numbers:
- 10
- 1,2,3
- 1-3
- 5-10,1,3-4
'/<subtest' part is optional, but has the same format. E.g., to select
test #3 and its sub-tests #10 through #15, use: -t 3/10-15.
Similarly, to select tests by name, use `-t verif/strobe`:
$ sudo ./test_progs -t verif/strobe
#3/12 strobemeta.o:OK
#3/13 strobemeta_nounroll1.o:OK
#3/14 strobemeta_nounroll2.o:OK
#3 bpf_verif_scale:OK
Summary: 1/3 PASSED, 0 FAILED
Example of using subtest API is in the next patch, converting
bpf_verif_scale.c tests to use sub-tests.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch changes how test output is printed out. By default, if test
had no errors, the only output will be a single line with test number,
name, and verdict at the end, e.g.:
#31 xdp:OK
If test had any errors, all log output captured during test execution
will be output after test completes.
It's possible to force output of log with `-v` (`--verbose`) option, in
which case output won't be buffered and will be output immediately.
To support this, individual tests are required to use helper methods for
logging: `test__printf()` and `test__vprintf()`.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make test_progs test runner own libbpf logging. Also introduce two
levels of verbosity: -v and -vv. First one will be used in subsequent
patches to enable test log output always. Second one increases verbosity
level of libbpf logging further to include debug output as well.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
By returning previously set print callback from libbpf_set_print, it's
possible to restore it, eventually. This is useful when running many
independent test with one default print function, but overriding log
verbosity for particular subset of tests.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add ability to specify either test number or test name substring to
narrow down a set of test to run.
Usage:
sudo ./test_progs -n 1
sudo ./test_progs -t attach_probe
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Refactor test_progs to allow better control on what's being run.
Also use argp to do argument parsing, so that it's easier to keep adding
more options.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Apprently listing header as a normal dependency for a binary output
makes it go through compilation as if it was C code. This currently
works without a problem, but in subsequent commits causes problems for
differently generated test.h for test_progs. Marking those headers as
order-only dependency solves the issue.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes and functional updates:
- Prevent stale huge I/O TLB mappings on 32bit. A long standing bug
which got exposed by KPTI support for 32bit
- Prevent bogus access_ok() warnings in arch_stack_walk_user()
- Add display quirks for Lenovo devices which have height and width
swapped
- Add the missing CR2 fixup for 32 bit async pagefaults. Fallout of
the CR2 bug fix series.
- Unbreak handling of force enabled HPET by moving the 'is HPET
counting' check back to the original place.
- A more accurate check for running on a hypervisor platform in the
MDS mitigation code. Not perfect, but more accurate than the
previous one.
- Update a stale and confusing comment vs. IRQ stacks"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/mds: Apply more accurate check on hypervisor platform
x86/hpet: Undo the early counter is counting check
x86/entry/32: Pass cr2 to do_async_page_fault()
x86/irq/64: Update stale comment
x86/sysfb_efi: Add quirks for some devices with swapped width and height
x86/stacktrace: Prevent access_ok() warnings in arch_stack_walk_user()
mm/vmalloc: Sync unmappings in __purge_vmap_area_lazy()
x86/mm: Sync also unmappings in vmalloc_sync_all()
x86/mm: Check for pfn instead of page in vmalloc_sync_one()
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for the fair scheduling class:
- Prevent freeing memory which is accessible by concurrent readers
- Make the RCU annotations for numa groups consistent"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Use RCU accessors consistently for ->numa_group
sched/fair: Don't free p->numa_faults with concurrent readers
Pull perf fixes from Thomas Gleixner:
"A pile of perf related fixes:
Kernel:
- Fix SLOTS PEBS event constraints for Icelake CPUs
- Add the missing mask bit to allow counting hardware generated
prefetches on L3 for Icelake CPUs
- Make the test for hypervisor platforms more accurate (as far as
possible)
- Handle PMUs correctly which override event->cpu
- Yet another missing fallthrough annotation
Tools:
perf.data:
- Fix loading of compressed data split across adjacent records
- Fix buffer size setting for processing CPU topology perf.data
header.
perf stat:
- Fix segfault for event group in repeat mode
- Always separate "stalled cycles per insn" line, it was being
appended to the "instructions" line.
perf script:
- Fix --max-blocks man page description.
- Improve man page description of metrics.
- Fix off by one in brstackinsn IPC computation.
perf probe:
- Avoid calling freeing routine multiple times for same pointer.
perf build:
- Do not use -Wshadow on gcc < 4.8, avoiding too strict warnings
treated as errors, breaking the build"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Mark expected switch fall-throughs
perf/core: Fix creating kernel counters for PMUs that override event->cpu
perf/x86: Apply more accurate check on hypervisor platform
perf/x86/intel: Fix invalid Bit 13 for Icelake MSR_OFFCORE_RSP_x register
perf/x86/intel: Fix SLOTS PEBS event constraint
perf build: Do not use -Wshadow on gcc < 4.8
perf probe: Avoid calling freeing routine multiple times for same pointer
perf probe: Set pev->nargs to zero after freeing pev->args entries
perf session: Fix loading of compressed data split across adjacent records
perf stat: Always separate stalled cycles per insn
perf stat: Fix segfault for event group in repeat mode
perf tools: Fix proper buffer size for feature processing
perf script: Fix off by one in brstackinsn IPC computation
perf script: Improve man page description of metrics
perf script: Fix --max-blocks man page description
Pull locking fixes from Thomas Gleixner:
"A set of locking fixes:
- Address the fallout of the rwsem rework. Missing ACQUIREs and a
sanity check to prevent a use-after-free
- Add missing checks for unitialized mutexes when mutex debugging is
enabled.
- Remove the bogus code in the generic SMP variant of
arch_futex_atomic_op_inuser()
- Fixup the #ifdeffery in lockdep to prevent compile warnings"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/mutex: Test for initialized mutex
locking/lockdep: Clean up #ifdef checks
locking/lockdep: Hide unused 'class' variable
locking/rwsem: Add ACQUIRE comments
tty/ldsem, locking/rwsem: Add missing ACQUIRE to read_failed sleep loop
lcoking/rwsem: Add missing ACQUIRE to read_slowpath sleep loop
locking/rwsem: Add missing ACQUIRE to read_slowpath exit when queue is empty
locking/rwsem: Don't call owner_on_cpu() on read-owner
futex: Cleanup generic SMP variant of arch_futex_atomic_op_inuser()
Pull objtool fix from Thomas Gleixner:
"A single robustness fix for objtool to handle unbalanced CLAC
invocations under all circumstances"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Improve UACCESS coverage
Ido Schimmel says:
====================
mlxsw: spectrum_acl: Forbid unsupported filters
Patches #1-#2 make mlxsw reject unsupported egress filters. These
include filters that match on VLAN and filters associated with a
redirect action. Patch #1 rejects such filters when they are configured
on egress and patch #2 rejects such filters when they are configured in
a shared block that user tries to bind to egress.
Patch #3 forbids matching on reserved TCP flags as this is not supported
by the current keys that mlxsw uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching on reserved TCP flags bits is only supported using custom
parser. Since the usecase for that is not known now, just forbid to
offload rules that match on these bits.
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some matches and actions are not supported on egress. Track such rules
and forbid a bind of block which contains them to egress.
With this patch, the kernel tells the user he cannot do that:
$ tc qdisc add dev ens16np1 ingress_block 22 clsact
$ tc filter add block 22 protocol 802.1q pref 2 handle 101 flower vlan_id 100 skip_sw action pass
$ tc qdisc add dev ens16np2 egress_block 22 clsact
Error: mlxsw_spectrum: Block cannot be bound to egress because it contains unsupported rules.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum ASIC does not support redirection on egress, so refuse to
insert such flows:
$ tc qdisc add dev ens16np1 clsact
$ tc filter add dev ens16np1 egress protocol all pref 1 handle 101 flower skip_sw action mirred egress redirect dev ens16np2
Error: mlxsw_spectrum: Redirect action is not supported on egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204079
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Reported-by: Dušan Dragić <dragic.dusan@gmail.com>
Tested-by: Dušan Dragić <dragic.dusan@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a6851c613f.
It was reported that RTL8111b successfully finishes 1000/Full autoneg
but no data flows. Reverting the original patch fixes the issue.
It seems to be a HW issue with the integrated RTL8211B PHY. This PHY
version used also e.g. on RTL8168d, so better revert the original patch.
Reported-by: Bernhard Held <berny156@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Dutch consumer grade ISDN network will be shut down on September 1,
2019. This means I'll be converted to some sort of VOIP shortly. At that
point it would be unwise to try to maintain the gigaset driver, even for
odd fixes as I do. So I'll stop maintaining it as a seperate driver and
bump support to CAPI in staging. De facto this means the driver will be
unmaintained, since no-one seems to be working on CAPI.
I've lighty tested the hardware specific modules of this driver (bas-gigaset,
ser-gigaset, and usb-gigaset) for v5.3-rc1. The basic functionality appears to
be working. It's unclear whether anyone still cares. I'm aware of only one
person sort of using the driver a few years ago.
Thanks to Karsten Keil for the ISDN subsystems gigaset was using (I4L and
CAPI). And many thanks to Hansjoerg Lipp and Tilman Schmidt for writing and
upstreaming this driver.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: improve HW csum and TSO handling
This series:
- delegates more tasks from the driver to the core
- enables HW csum and TSO per default
- copies quirks for buggy chip versions from vendor driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable HW csum and TSO per default except on known buggy chip versions.
Realtek confirmed that RTL8168evl has a HW issue with TSO.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop in r8169_csum_workaround is called only if in
msdn_giant_send_check a copy of the skb header needs to be made and
we don't have enough memory. Let's simply drop the packet in that case
so that we can remove r8169_csum_workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement callback ndo_features_check and move all feature checks there.
This will allow us to get rid of r8169_csum_workaround() completely in
a subsequent step. Like in the vendor driver disable HW csum for short
packets on RTL8168b.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set GSO max size and max segment number as in the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_find_hdr() prints a non-rate limited error message
when it cannot find an ipv6 header at a specific offset.
This could be used as a DoS, so just remove it.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align setting PME with the vendor driver. PMEnable is writable on
RTL8169 only, on later chip versions it's read-only. PME_SIGNAL is
used on chip versions from RTL8168evl with the exception of the
RTL8168f family.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX-3 Pro can offload transmission of VLAN packets with VXLAN inside:
enable tunnel offloads in dev->vlan_features, like it's done with other
NIC drivers (e.g. be2net and ixgbe).
It's no more necessary to change dev->hw_enc_features when VXLAN are added
or removed, since .ndo_features_check() already checks for VXLAN packet
where the UDP destination port matches the configured value. Just set
dev->hw_enc_features when the NIC is initialized, so that overlying VLAN
can correctly inherit the tunnel offload capabilities.
Changes since v1:
- avoid flipping hw_enc_features, instead of calling netdev notifiers,
thanks to Saeed Mahameed
- squash two patches into a single one
CC: Paolo Abeni <pabeni@redhat.com>
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_ACPI is unset (arm allyesconfig), status is unused.
drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c:383:14: warning:
unused variable 'status' [-Wunused-variable]
acpi_status status;
^
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:440:14: warning:
unused variable 'status' [-Wunused-variable]
acpi_status status;
^
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:697:14: warning: unused
variable 'status' [-Wunused-variable]
acpi_status status;
^
Move the declaration into the CONFIG_ACPI block so that there are no
compiler warnings.
Fixes: 570d785ba4 ("drivers: net: xgene: Remove acpi_has_method() calls")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rds_rdma_cm_event_handler_cmn(), there are some if statements to
check whether conn is NULL, such as on lines 65, 96 and 112.
But conn is not checked before being used on line 108:
trans->cm_connect_complete(conn, event);
and on lines 140-143:
rdsdebug("DISCONNECT event - dropping connection "
"%pI6c->%pI6c\n", &conn->c_laddr,
&conn->c_faddr);
rds_conn_drop(conn);
Thus, possible null-pointer dereferences may occur.
To fix these bugs, conn is checked before being used.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-9 complains about a blatant uninitialized variable use that
all earlier compiler versions missed:
drivers/iio/adc/rcar-gyroadc.c:510:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Return -EINVAL instead here and a few lines above it where
we accidentally return 0 on failure.
Cc: stable@vger.kernel.org
Fixes: 059c53b323 ("iio: adc: Add Renesas GyroADC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The stmmaceth clock is specified by the slave_bus and apb_pclk clocks in
the device tree bindings for snps,dwc-qos-ethernet-4.10 compatible nodes
of this IP.
The subdrivers for these bindings will be requesting the stmmac clock
correctly at a later point, so there is no need to request it here and
cause an error message to be printed to the kernel log.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tegra EQOS driver already resets the MDIO bus at probe time via the
reset GPIO specified in the phy-reset-gpios device tree property. There
is no need to reset the bus again later on.
This avoids the need to query the device tree for the snps,reset GPIO,
which is not part of the Tegra EQOS device tree bindings. This quiesces
an error message from the generic bus reset code if it doesn't find the
snps,reset related delays.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable bucket is being initialized with a value that is never
read and it is being updated later with a new value in a following
for-loop. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In start_isoc_chain(), usb_alloc_urb() on line 1392 may fail
and return NULL. At this time, fifo->iso[i].urb is assigned to NULL.
Then, fifo->iso[i].urb is used at some places, such as:
LINE 1405: fill_isoc_urb(fifo->iso[i].urb, ...)
urb->number_of_packets = num_packets;
urb->transfer_flags = URB_ISO_ASAP;
urb->actual_length = 0;
urb->interval = interval;
LINE 1416: fifo->iso[i].urb->...
LINE 1419: fifo->iso[i].urb->...
Thus, possible null-pointer dereferences may occur.
To fix these bugs, "continue" is added to avoid using fifo->iso[i].urb
when it is NULL.
These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Wimplicit-fallthrough enablement from Gustavo A. R. Silva:
"This marks switch cases where we are expecting to fall through, and
globally enables the -Wimplicit-fallthrough option in the main
Makefile.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
With these changes, we completely get rid of all the fall-through
warnings in the kernel"
* tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Makefile: Globally enable fall-through warning
drm/i915: Mark expected switch fall-throughs
drm/amd/display: Mark expected switch fall-throughs
drm/amdkfd/kfd_mqd_manager_v10: Avoid fall-through warning
drm/amdgpu/gfx10: Fix missing break in switch statement
drm/amdkfd: Fix missing break in switch statement
perf/x86/intel: Mark expected switch fall-throughs
mtd: onenand_base: Mark expected switch fall-through
afs: fsclient: Mark expected switch fall-throughs
afs: yfsclient: Mark expected switch fall-throughs
can: mark expected switch fall-throughs
firewire: mark expected switch fall-throughs
Pull s390 updates from Heiko Carstens:
- Add ABI to kernel image file which allows e.g. the file utility to
figure out the kernel version.
- Wire up clone3 system call.
- Add support for kasan bitops instrumentation.
- uapi header cleanup: use __u{16,32,64} instead of uint{16,32,64}_t.
- Provide proper ARCH_ZONE_DMA_BITS so the s390 DMA zone is correctly
defined with 2 GB instead of the default value of 1 MB.
- Farhan Ali leaves the group of vfio-ccw maintainers.
- Various small vfio-ccw fixes.
- Add missing locking for airq_areas array in virtio code.
- Minor qdio improvements.
* tag 's390-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
MAINTAINERS: vfio-ccw: Remove myself as the maintainer
s390/mm: use shared variables for sysctl range check
virtio/s390: fix race on airq_areas[]
s390/dma: provide proper ARCH_ZONE_DMA_BITS value
s390/kasan: add bitops instrumentation
s390/bitops: make test functions return bool
s390: wire up clone3 system call
kbuild: enable arch/s390/include/uapi/asm/zcrypt.h for uapi header test
s390: use __u{16,32,64} instead of uint{16,32,64}_t in uapi header
s390/hypfs: fix a typo in the name of a function
s390/qdio: restrict QAOB usage to IQD unicast queues
s390/qdio: add sanity checks to the fast-requeue path
s390: enable detection of kernel version from bzImage
Documentation: fix vfio-ccw doc
vfio-ccw: Update documentation for csch/hsch
vfio-ccw: Don't call cp_free if we are processing a channel program
vfio-ccw: Set pa_nr to 0 if memory allocation fails for pa_iova_pfn
vfio-ccw: Fix memory leak and don't call cp_free in cp_init
vfio-ccw: Fix misleading comment when setting orb.cmd.c64
Pull Devicetree fixes from Rob Herring:
"The nvmem changes would typically go thru Greg's tree, but they were
missed in the merge window. [ Acked by Greg ]
Summary:
- Fix mismatches in $id values and actual filenames. Now checked by
tools.
- Convert nvmem binding to DT schema
- Fix a typo in of_property_read_bool() kerneldoc
- Remove some redundant description in al-fic interrupt-controller"
* tag 'devicetree-fixes-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Fix more $id value mismatches filenames
dt-bindings: nvmem: SID: Fix the examples node names
dt-bindings: nvmem: Add YAML schemas for the generic NVMEM bindings
of: Fix typo in kerneldoc
dt-bindings: interrupt-controller: al-fic: remove redundant binding
dt-bindings: clk: allwinner,sun4i-a10-ccu: Correct path in $id
Pull libnvdimm fixes from Dan Williams:
"A collection of locking and async operations fixes for v5.3-rc2. These
had been soaking in a branch targeting the merge window, but missed
due to a regression hunt. This fixed up version has otherwise been in
-next this past week with no reported issues.
In order to gain confidence in the locking changes the pull also
includes a debug / instrumentation patch to enable lockdep coverage
for libnvdimm subsystem operations that depend on the device_lock for
exclusion. As mentioned in the changelog it is a hack, but it works
and documents the locking expectations of the sub-system in a way that
others can use lockdep to verify. The driver core touches got an ack
from Greg.
Summary:
- Fix duplicate device_unregister() calls (multiple threads competing
to do unregister work when scheduling device removal from a sysfs
attribute of the self-same device).
- Fix badblocks registration order bug. Ensure region badblocks are
initialized in advance of namespace registration.
- Fix a deadlock between the bus lock and probe operations.
- Export device-core infrastructure to coordinate async operations
via the device ->dead state.
- Add device-core infrastructure to validate device_lock() usage with
lockdep"
* tag 'libnvdimm-fixes-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
driver-core, libnvdimm: Let device subsystems add local lockdep coverage
libnvdimm/bus: Fix wait_nvdimm_bus_probe_idle() ABBA deadlock
libnvdimm/bus: Stop holding nvdimm_bus_list_mutex over __nd_ioctl()
libnvdimm/bus: Prepare the nd_ioctl() path to be re-entrant
libnvdimm/region: Register badblocks before namespaces
libnvdimm/bus: Prevent duplicate device_unregister() calls
drivers/base: Introduce kill_device()
There are two references to the generic counter ABI, with was added
on a separate patch. Both point to a non-existing file.
Fix them.
Fixes: ea2b23b895 ("counter: Documentation: Add Generic Counter sysfs documentation")
Fixes: 09e7d4ed89 ("docs: Add Generic Counter interface documentation")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Distribution installation images such as Debian include different sets
of modules which can be downloaded dynamically. Such images may notably
include the hda sound modules but not the i915 DRM module, even if the
latter was enabled at build time, as reported on
https://bugs.debian.org/931507
In such a case hdac_i915 would be linked in and try to load the i915
module, fail since it is not there, but still wait for a whole minute
before giving up binding with it.
This fixes such as case by only waiting for the binding if the module
was properly loaded (or module support is disabled, in which case i915
is already compiled-in anyway).
Fixes: f9b54e1961 ("ALSA: hda/i915: Allow delayed i915 audio component binding")
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is unused since commit 9f69a496f1 ("kbuild: split out *.mod out
of {single,multi}-used-m rules").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
