In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code tries to store the link rate (in bps, which is a big
number) in a u8, which surely overflow. Then it's converted back to
bandwidth code (which is thus 0) and written to the chip.
The code sometimes works because the chip will automatically fallback to
the lowest possible DP link rate (1.62Gbps) when get the invalid value.
However, on the eDP panel of Olimex TERES-I, which wants 2.7Gbps link,
it failed.
As we had already read the link bandwidth as bandwidth code in earlier
code (to check whether it is supported), use it when setting bandwidth,
instead of converting it to link rate and then converting back.
Fixes: e1cff82c10 ("drm/bridge: fix anx6345 compilation for v5.5")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221165127.813325-1-icenowy@aosc.io
Pull a devfreq fix for 5.6-rc4 from Chanwoo Choi:
"Revert "PM / devfreq: Modify the device name as devfreq(X) for sysfs"
- This changes as devfreq(X) cause break some user space applications
such as Android HAL from Unisoc and Hikey. In result, decide to revert it
for preventing the HAL layer problem."
* tag 'devfreq-fixes-for-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
Revert "PM / devfreq: Modify the device name as devfreq(X) for sysfs"
Before commit 1e4f63aecb ("cpufreq: Avoid creating excessively
large stack frames") the initial value of the policy field in struct
cpufreq_policy set by the driver's ->init() callback was implicitly
passed from cpufreq_init_policy() to cpufreq_set_policy() if the
default governor was neither "performance" nor "powersave". After
that commit, however, cpufreq_init_policy() must take that case into
consideration explicitly and handle it as appropriate, so make that
happen.
Fixes: 1e4f63aecb ("cpufreq: Avoid creating excessively large stack frames")
Link: https://lore.kernel.org/linux-pm/39fb762880c27da110086741315ca8b111d781cd.camel@gmail.com/
Reported-by: Artem Bityutskiy <dedekind1@gmail.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.
Fixes: 481a7d154c ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware paths for the VSC8584 PHYs not not contain the leading
'microchip/' directory, as used in linux-firmware, resulting in an
error when probing the driver. This patch fixes it.
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.
All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When auto-negotiation is not required, return value should be zero.
Changes v1->v2:
- improved comments and code as Andrew Lunn and Heiner Kallweit suggestion
- fixed issue in genphy_c45_check_and_restart_aneg as Russell King
suggestion.
Fixes: 2a10ab043a ("net: phy: add genphy_check_and_restart_aneg()")
Fixes: 1af9f16840 ("net: phy: add genphy_c45_check_and_restart_aneg()")
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an SMC connection to a certain peer is setup the first time,
a new linkgroup is created. In case of setup failures, such a
linkgroup is unusable and should disappear. As a first step the
linkgroup is removed from the linkgroup list in smc_lgr_forget().
There are 2 problems:
smc_listen_decline() might be called before linkgroup creation
resulting in a crash due to calling smc_lgr_forget() with
parameter NULL.
If a setup failure occurs after linkgroup creation, the connection
is never unregistered from the linkgroup, preventing linkgroup
freeing.
This patch introduces an enhanced smc_lgr_cleanup_early() function
which
* contains a linkgroup check for early smc_listen_decline()
invocations
* invokes smc_conn_free() to guarantee unregistering of the
connection.
* schedules fast linkgroup removal of the unusable linkgroup
And the unused function smcd_conn_free() is removed from smc_core.h.
Fixes: 3b2dec2603 ("net/smc: restructure client and server code in af_smc")
Fixes: 2a0674fffb ("net/smc: improve abnormal termination of link groups")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Outdated Raspberry Pi 4 firmware might configure the external PHY as
rgmii although the kernel currently sets it as rgmii-rxid. This makes
connections unreliable as ID_MODE_DIS is left enabled. To avoid this,
explicitly clear that bit whenever we don't need it.
Fixes: da38802211 ("net: bcmgenet: Add RGMII_RXID support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The put of the flags was added by the commit referenced in fixes tag,
however the size of the message was not extended accordingly.
Fix this by adding size of the flags bitfield to the message size.
Fixes: e382267860 ("net: sched: update action implementations to support flags")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to list_for_each_entry_rcu() to silence
false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled.
The devlink->lock is held when devlink_dpipe_table_find()
is called in non RCU read side section. Therefore, pass struct devlink
to devlink_dpipe_table_find() for lockdep checking.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes: de34d7084e ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes:
1) Perform garbage collection from workqueue to fix rcu detected
stall in ipset hash set types, from Jozsef Kadlecsik.
2) Fix the forceadd evaluation path, also from Jozsef.
3) Fix nft_set_pipapo selftest, from Stefano Brivio.
4) Crash when add-flush-add element in pipapo set, also from Stefano.
Add test to cover this crash.
5) Remove sysctl entry under mutex in hashlimit, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull chrome platform fix from Benson Leung:
"Fix a build warning"
* tag 'tag-chrome-platform-fixes-for-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: Include asm/unaligned instead of linux/ path
Before releasing the global mutex, we only unlink the hashtable
from the hash list, its proc file is still not unregistered at
this point. So syzbot could trigger a race condition where a
parallel htable_create() could register the same file immediately
after the mutex is released.
Move htable_remove_proc_entry() back to mutex protection to
fix this. And, fold htable_destroy() into htable_put() to make
the code slightly easier to understand.
Reported-and-tested-by: syzbot+d195fd3b9a364ddd6731@syzkaller.appspotmail.com
Fixes: c4a3922d2d ("netfilter: xt_hashlimit: reduce hashlimit_mutex scope for htable_put()")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Syzbot reported that ethnl_compact_sanity_checks() can be tricked into
reading past the end of ETHTOOL_A_BITSET_VALUE and ETHTOOL_A_BITSET_MASK
attributes and even the message by passing a value between (u32)(-31)
and (u32)(-1) as ETHTOOL_A_BITSET_SIZE.
The problem is that DIV_ROUND_UP(attr_nbits, 32) is 0 for such values so
that zero length ETHTOOL_A_BITSET_VALUE will pass the length check but
ethnl_bitmap32_not_zero() check would try to access up to 512 MB of
attribute "payload".
Prevent this overflow byt limiting the bitset size. Technically, compact
bitset format would allow bitset sizes up to almost 2^18 (so that the
nest size does not exceed U16_MAX) but bitsets used by ethtool are much
shorter. S16_MAX, the largest value which can be directly used as an
upper limit in policy, should be a reasonable compromise.
Fixes: 10b518d4e6 ("ethtool: netlink bitset handling")
Reported-by: syzbot+7fd4ed5b4234ab1fdccd@syzkaller.appspotmail.com
Reported-by: syzbot+709b7a64d57978247e44@syzkaller.appspotmail.com
Reported-by: syzbot+983cb8fb2d17a7af549d@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the lower and upper bounds when there are multiple TCs and
traffic is on the the same TC on the same device.
The lower bound is represented by 'qoffset' and the upper limit for
hash value is 'qcount + qoffset'. This gives a clean Rx to Tx queue
mapping when there are multiple TCs, as the queue indices for upper TCs
will be offset by 'qoffset'.
v2: Fixed commit description based on comments.
Fixes: 1b837d489e ("net: Revoke export for __skb_tx_hash, update it to just be static skb_tx_hash")
Fixes: eadec877ce ("net: Add support for subordinate traffic classes to netdev_pick_tx")
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's the last user, and more importantly, it's the last non-legacy
user of anything in drm_pci.c.
The only tricky bit is the agp initialization. But a close look shows
that radeon does not use the drm_agp midlayer (the main use of that is
drm_bufs for legacy drivers), and instead could use the agp subsystem
directly (like nouveau does already). Hence we can just pull this in
too.
A further step would be to entirely drop the use of drm_device->agp,
but feels like too much churn just for this patch.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Recent omap changes added runtime checks to use omap_smccc_smc()
when optee is configured in dts. As the omap-secure code can be
built for ARMv6 only without ARMv7 and use custom smc calls, we
now get a build error:
omap-secure.c:(.text+0x94): undefined reference to `__arm_smccc_smc'
As there secure calls are not used for ARMv6, we should not build
secure-common, and not call omap_secure_init() for omap2.
Fixes: c37baa06f8 ("ARM: OMAP2+: Fix undefined reference to omap_secure_init")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Steven Price <steven.price@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.
Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.
Fixes: 895bd4b3e5 ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull tracing and bootconfig updates:
"Fixes and changes to bootconfig before it goes live in a release.
Change in API of bootconfig (before it comes live in a release):
- Have a magic value "BOOTCONFIG" in initrd to know a bootconfig
exists
- Set CONFIG_BOOT_CONFIG to 'n' by default
- Show error if "bootconfig" on cmdline but not compiled in
- Prevent redefining the same value
- Have a way to append values
- Added a SELECT BLK_DEV_INITRD to fix a build failure
Synthetic event fixes:
- Switch to raw_smp_processor_id() for recording CPU value in preempt
section. (No care for what the value actually is)
- Fix samples always recording u64 values
- Fix endianess
- Check number of values matches number of fields
- Fix a printing bug
Fix of trace_printk() breaking postponed start up tests
Make a function static that is only used in a single file"
* tag 'trace-v5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Fix CONFIG_BOOTTIME_TRACING dependency issue
bootconfig: Add append value operator support
bootconfig: Prohibit re-defining value on same key
bootconfig: Print array as multiple commands for legacy command line
bootconfig: Reject subkey and value on same parent key
tools/bootconfig: Remove unneeded error message silencer
bootconfig: Add bootconfig magic word for indicating bootconfig explicitly
bootconfig: Set CONFIG_BOOT_CONFIG=n by default
tracing: Clear trace_state when starting trace
bootconfig: Mark boot_config_checksum() static
tracing: Disable trace_printk() on post poned tests
tracing: Have synthetic event test use raw_smp_processor_id()
tracing: Fix number printing bug in print_synth_event()
tracing: Check that number of vals matches number of synth event fields
tracing: Make synth_event trace functions endian-correct
tracing: Make sure synth_event_trace() example always uses u64
Pull Kunit fixes from Shuah Khan:
"This Kselftest kunit update consists of fixes to documentation and
the run-time tool from Brendan Higgins and Heidi Fahim"
* tag 'linux-kselftest-kunit-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: run kunit_tool from any directory
kunit: test: Improve error messages for kunit_tool when kunitconfig is invalid
Documentation: kunit: fixed sphinx error in code block
Pull Kselftest fixes from Shuah Khan:
- fixes to TIMEOUT failures and out-of-tree compilation compilation
errors from Michael Ellerman.
- declutter git status fix from Christophe Leroy
* tag 'linux-kselftest-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/rseq: Fix out-of-tree compilation
selftests: Install settings files to fix TIMEOUT failures
selftest/lkdtm: Don't pollute 'git status'
Because of the i2c quirk we have the reset quirks named in a confusing
way. Let's fix the 1-wire quirk accordinlyg. Then let's switch to using
better naming later on.
Fixes: 4e23be473e ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit ead68df94d.
Using the -Werror flag breaks the build for me due to mostly harmless
KASAN or similar warnings:
arch/x86/kvm/x86.c: In function ‘kvm_timer_init’:
arch/x86/kvm/x86.c:7209:1: error: the frame size of 1112 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Feel free to add a CONFIG_WERROR if you care strong enough, but don't
break peoples builds for absolutely no good reason.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When queueing a signal, we increment both the users count of pending
signals (for RLIMIT_SIGPENDING tracking) and we increment the refcount
of the user struct itself (because we keep a reference to the user in
the signal structure in order to correctly account for it when freeing).
That turns out to be fairly expensive, because both of them are atomic
updates, and particularly under extreme signal handling pressure on big
machines, you can get a lot of cache contention on the user struct.
That can then cause horrid cacheline ping-pong when you do these
multiple accesses.
So change the reference counting to only pin the user for the _first_
pending signal, and to unpin it when the last pending signal is
dequeued. That means that when a user sees a lot of concurrent signal
queuing - which is the only situation when this matters - the only
atomic access needed is generally the 'sigpending' count update.
This was noticed because of a particularly odd timing artifact on a
dual-socket 96C/192T Cascade Lake platform: when you get into bad
contention, on that machine for some reason seems to be much worse when
the contention happens in the upper 32-byte half of the cacheline.
As a result, the kernel test robot will-it-scale 'signal1' benchmark had
an odd performance regression simply due to random alignment of the
'struct user_struct' (and pointed to a completely unrelated and
apparently nonsensical commit for the regression).
Avoiding the double increments (and decrements on the dequeueing side,
of course) makes for much less contention and hugely improved
performance on that will-it-scale microbenchmark.
Quoting Feng Tang:
"It makes a big difference, that the performance score is tripled! bump
from original 17000 to 54000. Also the gap between 5.0-rc6 and
5.0-rc6+Jiri's patch is reduced to around 2%"
[ The "2% gap" is the odd cacheline placement difference on that
platform: under the extreme contention case, the effect of which half
of the cacheline was hot was 5%, so with the reduced contention the
odd timing artifact is reduced too ]
It does help in the non-contended case too, but is not nearly as
noticeable.
Reported-and-tested-by: Feng Tang <feng.tang@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Philip Li <philip.li@intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The struct blk_mq_hw_ctx pointer argument in blk_mq_put_tag(),
blk_mq_poll_nsecs(), and blk_mq_poll_hybrid_sleep() is unused, so remove
it.
Overall obj code size shows a minor reduction, before:
text data bss dec hex filename
27306 1312 0 28618 6fca block/blk-mq.o
4303 272 0 4575 11df block/blk-mq-tag.o
after:
27282 1312 0 28594 6fb2 block/blk-mq.o
4311 272 0 4583 11e7 block/blk-mq-tag.o
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Garry <john.garry@huawei.com>
--
This minor patch had been carried as part of the blk-mq shared tags RFC,
I'd rather not carry it anymore as it required rebasing, so now or never..
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The dt_binding_check is added to PHONY, but it is invisible when
$(dtstree) is empty. So, it is not specified as phony for
ARCH=x86 etc.
Add it to PHONY outside the ifneq ... endif block.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
The dtbs_check should be a phony target, but currently it is not
specified so.
'make dtbs_check' works even if a file named 'dtbs_check' exists
because it depends on another phony target, scripts_dtc, but we
should not rely on it.
Add dtbs_check to PHONY.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
This if_change_rule is not working properly; it cannot detect any
command line change.
The reason is because cmd-check in scripts/Kbuild.include compares
$(cmd_$@) and $(cmd_$1), but cmd_dtc_dt_yaml does not exist here.
For if_change_rule to work properly, the stem part of cmd_* and rule_*
must match. Because this cmd_and_fixdep invokes cmd_dtc, this rule must
be named rule_dtc.
Fixes: 4f0e3a57d6 ("kbuild: Add support for DT binding schema checks")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
This sentence does not make sense in the section about mandatory-y.
This seems to be a copy-paste mistake of commit fcc8487d47 ("uapi:
export all headers under uapi directories").
The correct description would be "The convention is to list one
mandatory-y per line ...".
I just removed it instead of fixing it. If such information is needed,
it could be commented in include/asm-generic/Kbuild and
include/uapi/asm-generic/Kbuild.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Complete the comments for valid values of KBUILD_VERBOSE,
specifically for KBUILD_VERBOSE=2.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
