SMACK uses similar functions to control CIPSO, these are
the equivalent functions for CALIPSO and follow exactly
the same semantics.
int netlbl_cfg_calipso_add(struct calipso_doi *doi_def,
struct netlbl_audit *audit_info)
Adds a CALIPSO doi.
void netlbl_cfg_calipso_del(u32 doi, struct netlbl_audit *audit_info)
Removes a CALIPSO doi.
int netlbl_cfg_calipso_map_add(u32 doi, const char *domain,
const struct in6_addr *addr,
const struct in6_addr *mask,
struct netlbl_audit *audit_info)
Creates a mapping between a domain and a CALIPSO doi. If
addr and mask are non-NULL this creates an address-selector
type mapping.
This also extends netlbl_cfg_map_del() to remove IPv6 address-selector
mappings.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This works in exactly the same way as the CIPSO label cache.
The idea is to allow the lsm to cache the result of a secattr
lookup so that it doesn't need to perform the lookup for
every skbuff.
It introduces two sysctl controls:
calipso_cache_enable - enables/disables the cache.
calipso_cache_bucket_size - sets the size of a cache bucket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Lengths, checksum and the DOI are checked. Checking of the
level and categories are left for the socket layer.
CRC validation is performed in the calipso module to avoid
unconditionally linking crc_ccitt() into ipv6.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This makes it possible to route the error to the appropriate
labelling engine. CALIPSO is far less verbose than CIPSO
when encountering a bogus packet, so there is no need for a
CALIPSO error handler.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
In some cases, the lsm needs to add the label to the skbuff directly.
A NF_INET_LOCAL_OUT IPv6 hook is added to selinux to match the IPv4
behaviour. This allows selinux to label the skbuffs that it requires.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Request sockets need to have a label that takes into account the
incoming connection as well as their parent's label. This is used
for the outgoing SYN-ACK and for their child full-socket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
If set, these will take precedence over the parent's options during
both sending and child creation. If they're not set, the parent's
options (if any) will be used.
This is to allow the security_inet_conn_request() hook to modify the
IPv6 options in just the same way that it already may do for IPv4.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
CALIPSO is a hop-by-hop IPv6 option. A lot of this patch is based on
the equivalent CISPO code. The main difference is due to manipulating
the options in the hop-by-hop header.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This is to allow the CALIPSO labelling engine to use these.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
The functionality is equivalent to ipv6_renew_options() except
that the newopt pointer is in kernel, not user, memory
The kernel memory implementation will be used by the CALIPSO network
labelling engine, which needs to be able to set IPv6 hop-by-hop
options.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Remove a specified DOI through the NLBL_CALIPSO_C_REMOVE command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Enumerate the DOI list through the NLBL_CALIPSO_C_LISTALL command.
It takes no attributes.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Query a specified DOI through the NLBL_CALIPSO_C_LIST command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
The reply will contain:
NLBL_CALIPSO_A_MTYPE
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
CALIPSO is a packet labelling protocol for IPv6 which is very similar
to CIPSO. It is specified in RFC 5570. Much of the code is based on
the current CIPSO code.
This adds support for adding passthrough-type CALIPSO DOIs through the
NLBL_CALIPSO_C_ADD command. It requires attributes:
NLBL_CALIPSO_A_TYPE which must be CALIPSO_MAP_PASS.
NLBL_CALIPSO_A_DOI.
In passthrough mode the CALIPSO engine will map MLS secattr levels
and categories directly to the packet label.
At this stage, the major difference between this and the CIPSO
code is that IPv6 may be compiled as a module. To allow for
this the CALIPSO functions are registered at module init time.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
A recent cleanup moved MAX_IPTUN_ENCAP_OPS along with some other
definitions, but it is now invisible when CONFIG_INET is
not defined, but still referenced from ip6_tunnel.h:
In file included from net/xfrm/xfrm_input.c:17:0:
include/net/ip6_tunnel.h:67:17: error: 'MAX_IPTUN_ENCAP_OPS' undeclared here (not in a function)
ip6tun_encaps[MAX_IPTUN_ENCAP_OPS];
^~~~~~~~~~~~~~~~~~~
This hides the ip6_encap_hlen and ip6_tnl_encap functions inside
of CONFIG_INET so we don't run into the the problem.
Alternatively we could move the macro out of the #ifdef again to
restore the previous behavior
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 55c2bc1432 ("net: Cleanup encap items in ip_tunnels.h")
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a serious performance bug in packet schedulers using hrtimers.
sch_htb and sch_fq are definitely impacted by this problem.
We constantly rearm high resolution timers if some packets are throttled
in one (or more) class, and other packets are flying through qdisc on
another (non throttled) class.
hrtimer_start() does not have the mod_timer() trick of doing nothing if
expires value does not change :
if (timer_pending(timer) &&
timer->expires == expires)
return 1;
This issue is particularly visible when multiple cpus can queue/dequeue
packets on the same qdisc, as hrtimer code has to lock a remote base.
I used following fix :
1) Change htb to use qdisc_watchdog_schedule_ns() instead of open-coding
it.
2) Cache watchdog prior expiration. hrtimer might provide this, but I
prefer to not rely on some hrtimer internal.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->sk_shutdown bits share one bitfield with some other bits in sock struct,
such as ->sk_no_check_[r,t]x, ->sk_userlocks ...
sock_setsockopt() may write to these bits, while holding the socket lock.
In case of AF_UNIX sockets, we change ->sk_shutdown bits while holding only
unix_state_lock(). So concurrent setsockopt() and shutdown() may lead
to corrupting these bits.
Fix this by moving ->sk_shutdown bits out of bitfield into a separate byte.
This will not change the 'struct sock' size since ->sk_shutdown moved into
previously unused 16-bit hole.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a new fou6 module that provides encapsulation
operations for IPv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add encap_hlen and ip_tunnel_encap structure to ip6_tnl. Add functions
for getting encap hlen, setting up encap on a tunnel, performing
encapsulation operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create __fou_build_header and __gue_build_header. These implement the
protocol generic parts of building the fou and gue header.
fou_build_header and gue_build_header implement the IPv4 specific
functions and call the __*_build_header functions.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all the ip_tunnel_encap definitions in one spot in the
header file. Also, move ip_encap_hlen and ip_tunnel_encap from
ip_tunnel.c to ip_tunnels.h so they call be called without a dependency
on ip_tunnel module. Similarly, move iptun_encaps to ip_tunnel_core.c.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_CLS_ACT is disabled, we get a new warning in the mlx5
ethernet driver because the tc_for_each_action() loop never references
the iterator:
mellanox/mlx5/core/en_tc.c: In function 'mlx5e_stats_flower':
mellanox/mlx5/core/en_tc.c:431:20: error: unused variable 'a' [-Werror=unused-variable]
struct tc_action *a;
This changes the dummy tc_for_each_action() macro by adding a
cast to void, letting the compiler know that the variable is
intentionally declared but not used here. I could not come up
with a nicer workaround, but this seems to do the trick.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aad7e08d39 ("net/mlx5e: Hardware offloaded flower filter statistics support")
Fixes: 00175aec94 ("net/sched: Macro instead of CONFIG_NET_CLS_ACT ifdef")
Acked-By: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is not used anymore. nla_put_u64_64bit() should be used
instead.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new command in ndo_setup_tc() for hardware offloaded
filters, to call the NIC driver, and make it update the statistics.
This will be done before dumping the filter and its statistics.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce stats_update callback. netdev driver could call it for offloaded
actions to update the basic statistics (packets, bytes and last use).
Since bstats_update() and bstats_cpu_update() use skb as an argument to
get the counters, _bstats_update() and _bstats_cpu_update(), that get
bytes and packets as arguments, were added.
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On devices that support TC U32 offloads, this flag enables a filter to be
added only to HW. skip-sw and skip-hw are mutually exclusive flags. By
default without any flags, the filter is added to both HW and SW, but no
error checks are done in case of failure to add to HW. With skip-sw,
failure to add to HW is treated as an error.
Here is a sample script that adds 2 filters, one with skip-sw and the other
with skip-hw flag.
# add ingress qdisc
tc qdisc add dev p4p1 ingress
# enable hw tc offload.
ethtool -K p4p1 hw-tc-offload on
# add u32 filter with skip-sw flag.
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: flowid 800:1 \
skip-sw \
match ip src 192.168.1.0/24 \
action drop
# add u32 filter with skip-hw flag.
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: flowid 800:2 \
skip-hw \
match ip src 192.168.2.0/24 \
action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Some more work for 4.7, notably:
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Samuel Ortiz says:
====================
NFC 4.7 pull request
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
add the skb_iif to inet_skb_parm and set it in ipv4 code after clearing
the skb control buffer similar to IPv6. From there the pktinfo can just
pull it from cb with the PKTINFO_SKB_CB cast.
The previous patch moving the skb->dev change to L3 means nothing else
is needed for IPv6; it just works.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 2 arguments (cnt and rtt) in the congestion control modules'
pkts_acked() function with a struct. This will allow adding more
information without having to modify existing congestion control
modules (tcp_nv in particular needs bytes in flight when packet
was sent).
As proposed by Neal Cardwell in his comments to the tcp_nv patch.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an initial implementation of a netdev driver for GTP datapath
(GTP-U) v0 and v1, according to the GSM TS 09.60 and 3GPP TS 29.060
standards. This tunneling protocol is used to prevent subscribers from
accessing mobile carrier core network infrastructure.
This implementation requires a GGSN userspace daemon that implements the
signaling protocol (GTP-C), such as OpenGGSN [1]. This userspace daemon
updates the PDP context database that represents active subscriber
sessions through a genetlink interface.
For more context on this tunneling protocol, you can check the slides
that were presented during the NetDev 1.1 [2].
Only IPv4 is supported at this time.
[1] http://git.osmocom.org/openggsn/
[2] http://www.netdevconf.org/1.1/proceedings/slides/schultz-welte-osmocom-gtp.pdf
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a900689264 ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier patch changed lookup side to also net_eq() namespaces after
obtaining a reference on the conntrack, so a single kmemcache can be used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already include netns address in the hash, so we only need to use
net_eq in find_appropriate_src and can then put all entries into
same table.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
