The referenced commit moved the setting of the Autoneg and pause bits
early in sfp_parse_support(). However, we check whether the modes are
empty before using the bitrate to set some modes. Setting these bits
so early causes that test to always be false, preventing this working,
and thus some modules that used to work no longer do.
Move them just before the call to the quirk.
Fixes: 8110633db4 ("net: sfp-bus: allow SFP quirks to override Autoneg and pause bits")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/E1rPMJW-001Ahf-L0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b373 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: cafc3662ee ("net: micrel: Add PHC support for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make read_status more generic in preparation on moving it to shared
library as other PHY Family Driver will have the exact same
implementation.
The only specific part was a check for AR8031/33 if 1000basex was used.
The check is moved to a dedicated function specific for those PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA808x PHY Family supports Cable Diagnostic Test also for Cross Pair
Short.
Add all the define to make enable and support these additional tests.
Cross Short test was previously disabled by default, this is now changed
and enabled by default. In this mode, the mask changed a bit and length
is shifted based on the fault condition.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor qca808x cable test get status function to remove code
duplication and clean things up.
The same logic is applied to each pair hence it can be generalized and
moved to a common function.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generalize cable test fault length function since they all base on the
same magic values (already reverse engineered to understand the meaning
of it) to have consistenct values on every PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging the net-next tree, today's linux-next build (x86_64
allmodconfig) failed like this:
drivers/net/phy/aquantia/aquantia_firmware.c: In function 'aqr_fw_load_memory':
drivers/net/phy/aquantia/aquantia_firmware.c:135:23: error: implicit declaration of function 'crc_ccitt_false'; did you mean 'crc_ccitt_byte'? [-Werror=implicit-function-declaration]
135 | crc = crc_ccitt_false(crc, crc_data, sizeof(crc_data));
| ^~~~~~~~~~~~~~~
| crc_ccitt_byte
Caused by commit e93984ebc1 ("net: phy: aquantia: add firmware load support")
interacting with commit ("lib: crc_ccitt_false() is identical to crc_itu_t()")
from the mm tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20231221130946.7ed9a805@canb.auug.org.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move phylink_pcs_neg_mode() from the header file into the .c file since
nothing should be using it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luiz Angelo Daros de Luca reports that the MDIO bus code maintains a
reference to the DT node, but does not hold a refcount on the node.
The simple solution to this is to add the necessary refcounting into
the MDIO bus code for all users, ensuring that on registration, the
refcount is incremented, and only dropped when the MDIO bus is
released.
Do this for fwnodes, so we not only fix this for DT, but also other
types of firmware nodes as well.
Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the bus name is helpful when we want to expose the link topology
to userspace, add a helper to return the SFP bus name.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __of_mdiobus_register() function was storing the device node in
dev.of_node without increasing its reference count. It implicitly relied
on the caller to maintain the allocated node until the mdiobus was
unregistered.
Now, __of_mdiobus_register() will acquire the node before assigning it,
and of_mdiobus_unregister_callback() will be called at the end of
mdio_unregister().
Drivers can now release the node immediately after MDIO registration.
Some of them are already doing that even before this patch.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement mdo_insert_tx_tag to insert the TLV header in the ethernet
frame.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MACsec statistics callbacks.
The statistic registers must be set to 0 if the SC/SA is
deleted to read relevant values next time when the SC/SA is used.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MACsec support.
The MACsec block has four TX SCs and four RX SCs. The driver supports up
to four SecY. Each SecY with one TX SC and one RX SC.
The RX SCs can have two keys, key A and key B, written in hardware and
enabled at the same time.
The TX SCs can have two keys written in hardware, but only one can be
active at a given time.
On TX, the SC is selected using the MAC source address. Due of this
selection mechanism, each offloaded netdev must have a unique MAC
address.
On RX, the SC is selected by SCI(found in SecTAG or calculated using MAC
SA), or using RX SC 0 as implicit.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better align function variables to open parenthesis as suggested by
checkpatch script for qca808x function to make code cleaner.
For cable_test_get_status function some additional rework was needed to
handle too long functions.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2f3ce7a56c ("net: sfp: rework the RollBall PHY waiting code")
changed the long wait before accessing RollBall / FS modules into
probing for PHY every 1 second, and trying 25 times.
Wei Lei reports that this does not work correctly on FS modules: when
initializing, they may report values different from 0xffff in PHY ID
registers for some MMDs, causing get_phy_c45_ids() to find some bogus
MMD.
Fix this by adding the module_t_wait member back, and setting it to 4
seconds for FS modules.
Fixes: 2f3ce7a56c ("net: sfp: rework the RollBall PHY waiting code")
Reported-by: Wei Lei <quic_leiwei@quicinc.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Lei Wei <quic_leiwei@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY in PHY package may require to read/write MMD regs to correctly
configure the PHY package.
Add support for these additional required function in both lock and no
lock variant.
It's assumed that the entire PHY package is either C22 or C45. We use
C22 or C45 way of writing/reading to mmd regs based on the passed phydev
whether it's C22 or C45.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure phy_write_mmd and phy_read_mmd to implement generic helper
for direct mdiobus access for mmd and use these helper for phydev user.
This is needed in preparation of PHY package API that requires generic
access to the mdiobus and are deatched from phydev struct but instead
access them based on PHY package base_addr and offsets.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current API for PHY package are limited to single address to configure
global settings for the PHY package.
It was found that some PHY package (for example the qca807x, a PHY
package that is shipped with a bundle of 5 PHY) requires multiple PHY
address to configure global settings. An example scenario is a PHY that
have a dedicated PHY for PSGMII/serdes calibrarion and have a specific
PHY in the package where the global PHY mode is set and affects every
other PHY in the package.
Change the API in the following way:
- Change phy_package_join() to take the base addr of the PHY package
instead of the global PHY addr.
- Make __/phy_package_write/read() require an additional arg that
select what global PHY address to use by passing the offset from the
base addr passed on phy_package_join().
Each user of this API is updated to follow this new implementation
following a pattern where an enum is defined to declare the offset of the
addr.
We also drop the check if shared is defined as any user of the
phy_package_read/write is expected to use phy_package_join first. Misuse
of this will correctly trigger a kernel panic for NULL pointer
exception.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_parse_mode() populates all possible supported link modes for a
given phy_interface_t, for the case where a phylib phy may be absent and
we can't retrieve the supported link modes from that.
Russell points out that since the introduction of the generic validation
helpers phylink_get_capabilities() and phylink_caps_to_linkmodes(), we
can rewrite this procedure to populate the pl->supported mask, so that
instead of spelling out the link modes, we derive an intermediary
mac_capabilities bit field, and we convert that to the equivalent link
modes.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework read specific status function to be more generic. The function
apply different speed mask based on the PHY ID. Make it more generic by
adding an additional arg to pass the specific speed (ss) mask and use
the provided mask to parse the speed value.
This is needed to permit an easier deatch of qca808x code from the
at803x driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific qca808x config_aneg to dedicated function to permit easier
split of qca808x portion from at803x driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds abstractions to implement network PHY drivers; the
driver registration and bindings for some of callback functions in
struct phy_driver and many genphy_ functions.
This feature is enabled with CONFIG_RUST_PHYLIB_ABSTRACTIONS=y.
This patch enables unstable const_maybe_uninit_zeroed feature for
kernel crate to enable unsafe code to handle a constant value with
uninitialized data. With the feature, the abstractions can initialize
a phy_driver structure with zero easily; instead of initializing all
the members by hand. It's supposed to be stable in the not so distant
future.
Link: https://github.com/rust-lang/rust/pull/116218
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop specific PHY ID check for cable test functions for at803x. This is
done to make functions more generic. While at it better describe what
the functions does by using more symbolic function names.
PHYs that requires to set additional reg are moved to specific function
calling the more generic one.
cdt_start and cdt_wait_for_completion are changed to take an additional
arg to pass specific values specific to the PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move at8035 specific DT parse for clock out frequency to dedicated probe
to make at803x probe function more generic.
This is to tidy code and no behaviour change are intended.
Detection logic is changed, we check if the clk 25m mask is set and if
it's not zero, we assume the qca,clk-out-frequency property is set.
The property is checked in the generic at803x_parse_dt called by
at803x_probe.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move at8031 functions in dedicated section with dedicated at8031
parse_dt and probe.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename at8031 related DT function name to a more specific name
referencing they are only related to at8031 and not to the generic
at803x PHY family.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific at8031 config_intr bits to dedicated function to make
at803x_config_initr more generic.
This is needed in preparation for PHY driver split as qca8081 share the
same function to setup interrupts.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific at8031 WOL enable/disable to dedicated function to make
at803x_set_wol more generic.
This is needed in preparation for PHY driver split as qca8081 share the
same function to toggle WOL settings.
In this new implementation WOL module in at8031 is enabled after the
generic interrupt is setup. This should not cause any problem as the
WOL_INT has a separate implementation and only relay on MAC bits.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific at8031 config_init to dedicated function to make
at803x_config_init more generic and tidy things up.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific at8031 probe mode check to dedicated probe to make
at803x_probe more generic and keep code tidy.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific DT options for at8031 to specific probe to tidy things up
and make at803x_parse_dt more generic.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework qca83xx specific check to dedicated function to tidy things up
and drop useless phy_id check.
Also drop an useless link_change_notify for QCA8337 as it did nothing an
returned early.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function and the struct related to hw_stats were specific to qca83xx
PHY but were called following the convention in the driver of calling
everything with at803x prefix.
To better organize the code, rename these function a more specific name
to better describe that they are specific to 83xx PHY family.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the WOL disable call to specific at8031 probe to make at803x_probe
more generic and drop extra check for PHY ID.
Keep the same previous behaviour by first calling at803x_probe and then
disabling WOL.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix passing the wrong reference for config_initr on passing the function
pointer, drop the wrong & from at803x_config_intr in the PHY struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
