The function mipi_dbi_spi1_transfer() will transfer its payload as 9-bit
data, the 9th (MSB) bit being the data/command bit. In order to do that,
it unpacks the 8-bit values into 16-bit values, then sets the 9th bit if
the byte corresponds to data, clears it otherwise. The 7 MSB are
padding. The array of now 16-bit values is then passed to the SPI core
for transfer.
This function was broken since its introduction, as the length of the
SPI transfer was set to the payload size before its conversion, but the
payload doubled in size due to the 8-bit -> 16-bit conversion.
Fixes: 02dd95fe31 ("drm/tinydrm: Add MIPI DBI support")
Cc: <stable@vger.kernel.org> # 5.4+
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200703141341.1266263-1-paul@crapouillou.net
Recent kernels have been reported to panic using the bochs_drm
framebuffer under qemu-system-sparc64 which was bisected to
commit 7a0483ac4f ("drm/bochs: switch to generic drm fbdev emulation").
The backtrace indicates that the shadow framebuffer copy in
drm_fb_helper_dirty_blit_real() is trying to access the real
framebuffer using a virtual address rather than use an IO access
typically implemented using a physical (ASI_PHYS) access on SPARC.
The fix is to replace the memcpy with memcpy_toio() from io.h.
memcpy_toio() uses writeb() where the original fbdev code
used sbus_memcpy_toio(). The latter uses sbus_writeb().
The difference between writeb() and sbus_memcpy_toio() is
that writeb() writes bytes in little-endian, where sbus_writeb() writes
bytes in big-endian. As endian does not matter for byte writes they are
the same. So we can safely use memcpy_toio() here.
Note that this only fixes bochs, in general fbdev helpers still have
issues with mixing up system memory and __iomem space. Fixing that will
require a lot more work.
v3:
- Improved changelog (Daniel)
- Added FIXME to fbdev_use_iomem (Daniel)
v2:
- Added missing __iomem cast (kernel test robot)
- Made changelog readable and fix typos (Mark)
- Add flag to select iomem - and set it in the bochs driver
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200709193016.291267-1-sam@ravnborg.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200725191012.GA434957@ravnborg.org
Whenever a display update was sent, apart from updating
the memory base address, we called mcde_display_send_one_frame()
which also sent a command to the display requesting the TE IRQ
and enabling the FIFO.
When continuous updates are running this is wrong: we need
to only send this to start the flow to the display on
the very first update. This lead to the display pipeline
locking up and crashing.
Check if the flow is already running and in that case
do not call mcde_display_send_one_frame().
This fixes crashes on the Samsung GT-S7710 (Skomer).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200718233323.3407670-1-linus.walleij@linaro.org
On boe_nv133fhm_n62 (and presumably on boe_nv133fhm_n61) a scope shows
a small spike on the HPD line right when you power the panel on. The
picture looks something like this:
+--------------------------------------
|
|
|
Power ---+
+---
|
++ |
+----+| |
HPD -----+ +---------------------------+
So right when power is applied there's a little bump in HPD and then
there's small spike right before it goes low. The total time of the
little bump plus the spike was measured on one panel as being 8 ms
long. The total time for the HPD to go high on the same panel was
51.2 ms, though the datasheet only promises it is < 200 ms.
When asked about this glitch, BOE indicated that it was expected and
persisted until the TCON has been initialized.
If this was a real hotpluggable DP panel then this wouldn't matter a
whole lot. We'd debounce the HPD signal for a really long time and so
the little blip wouldn't hurt. However, this is not a hotpluggable DP
panel and the the debouncing logic isn't needed and just shows down
the time needed to get the display working. This is why the code in
panel_simple_prepare() doesn't do debouncing and just waits for HPD to
go high once. Unfortunately if we get unlucky and happen to poll the
HPD line right at the spike we can try talking to the panel before
it's ready.
Let's handle this situation by putting in a 15 ms prepare delay and
decreasing the "hpd absent delay" by 15 ms. That means:
* If you don't have HPD hooked up at all you've still got the
hardcoded 200 ms delay.
* If you've got HPD hooked up you will always wait at least 15 ms
before checking HPD. The only case where this could be bad is if
the panel is sharing a voltage rail with something else in the
system and was already turned on long before the panel came up. In
such a case we'll be delaying 15 ms for no reason, but it's not a
huge delay and I don't see any other good solution to handle that
case.
Even though the delay was measured as 8 ms, 15 ms was chosen to give a
bit of margin.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716132120.1.I01e738cd469b61fc9b28b3ef1c6541a4f48b11bf@changeid
The disp015x classes are used by both gt21x and gf1xx (aside from gf119), but page
kinds differ between Tesla and Fermi.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
NULL dereference occurs when string that is not ended with space or
newline is written to some dpm sysfs interface (for example pp_dpm_sclk).
This happens because strsep replaces the tmp with NULL if the delimiter
is not present in string, which is then dereferenced by tmp[0].
Reproduction example:
sudo sh -c 'echo -n 1 > /sys/class/drm/card0/device/pp_dpm_sclk'
Signed-off-by: Paweł Gronowski <me@woland.xyz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
"u64 *wptr" points to the the wptr value in write back buffer and
"*wptr = (*wptr) >> 2;" results in the value being overwritten each time
when ->get_wptr() is called.
umr uses /sys/kernel/debug/dri/0/amdgpu_ring_sdma0 to get rptr/wptr and
decode ring content and it is affected by this issue.
fix and simplify the logic similar as sdma_v4_0_ring_get_wptr().
v2: fix for sdma5.2 as well
v3: drop sdma 5.2 changes for 5.8 and stable
Suggested-by: Le Ma <le.ma@amd.com>
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
amdgpu_dm->backlight_caps is for single eDP only. the caps are upddated
for very connector. Real eDP caps will be overwritten by other external
display. For OLED panel, caps->aux_support is set to 1 for OLED pnael.
after external connected, caps+.aux_support is set to 0. This causes
OLED backlight adjustment not work.
[How]
within update_conector_ext_caps, backlight caps will be updated only for
eDP connector.
Cc: stable@vger.kernel.org
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prevents a warning in the MST create connector case.
v2: create global fake encoders rather per connector fake encoders
to avoid running out of encoder indices.
v3: use the actual number of crtcs on the asic rather than the max
to conserve encoders.
v4: v3 plus missing hunk I forgot to git add.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1108
Fixes: c6385e503a ("drm/amdgpu: drop legacy drm load and unload callbacks")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.7.x
Currently we're failing to recalculate the gen9 FBC w/a stride
unless something more drastic than just the modifier itself has
changed. This often leaves us with FBC enabled with the linear
fbdev framebuffer without the w/a stride enabled. That will cause
an immediate underrun and FBC will get promptly disabled.
Fix the problem by checking if the w/a stride is about to change,
and go through the full dance if so. This part of the FBC code
is still pretty much a disaster and will need lots more work.
But this should at least fix the immediate issue.
v2: Deactivate FBC when the modifier changes since that will
likely require resetting the w/a CFB stride
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200711080336.13423-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 0428ab013f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The assignment of metadata overwrote the new display resolution values,
hence we'd miss the size actually changed and wouldn't redefine the
surface. This would then lead to command buffer error when trying to
update the screen target (due to the size mismatch), and result in a
VM with black screen.
Fixes: 504901dbb0 ("drm/vmwgfx: Refactor surface_define to use vmw_surface_metadata")
Reviewed-by: Charmaine Lee <charmainel@vmware.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
Cc: stable@vger.kernel.org
clang static analysis flags this error
drivers/gpu/drm/radeon/ci_dpm.c:5652:9: warning: Use of memory after it is freed [unix.Malloc]
kfree(rdev->pm.dpm.ps[i].ps_priv);
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/radeon/ci_dpm.c:5654:2: warning: Attempt to free released memory [unix.Malloc]
kfree(rdev->pm.dpm.ps);
^~~~~~~~~~~~~~~~~~~~~~
problem is reported in ci_dpm_fini, with these code blocks.
for (i = 0; i < rdev->pm.dpm.num_ps; i++) {
kfree(rdev->pm.dpm.ps[i].ps_priv);
}
kfree(rdev->pm.dpm.ps);
The first free happens in ci_parse_power_table where it cleans up locally
on a failure. ci_dpm_fini also does a cleanup.
ret = ci_parse_power_table(rdev);
if (ret) {
ci_dpm_fini(rdev);
return ret;
}
So remove the cleanup in ci_parse_power_table and
move the num_ps calculation to inside the loop so ci_dpm_fini
will know how many array elements to free.
Fixes: cc8dbbb4f6 ("drm/radeon: add dpm support for CI dGPUs (v2)")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
