Reported on the Turris forum, mvneta provokes kernel warnings in the
architecture DMA mapping code when mvneta_setup_txqs() fails to
allocate memory. This happens because when mvneta_cleanup_txqs() is
called in the mvneta_stop() path, we leave pointers in the structure
that have been freed.
Then on mvneta_open(), we call mvneta_setup_txqs(), which starts
allocating memory. On memory allocation failure, mvneta_cleanup_txqs()
will walk all the queues freeing any non-NULL pointers - which includes
pointers that were previously freed in mvneta_stop().
Fix this by setting these pointers to NULL to prevent double-freeing
of the same memory.
Fixes: 2adb719d74 ("net: mvneta: Implement software TSO")
Link: https://forum.turris.cz/t/random-kernel-exceptions-on-hbl-tos-7-0/18865/8
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1phUe5-00EieL-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-28 (ice)
This series contains updates to ice driver only.
Jesse fixes mismatched header documentation reported when building with
W=1.
Brett restricts setting of VSI context to only applicable fields for the
given ICE_AQ_VSI_PROP_Q_OPT_VALID bit.
Junfeng adds check when adding Flow Director filters that conflict with
existing filter rules.
Jakob Koschel adds interim variable for iterating to prevent possible
misuse after looping.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix invalid check for empty list in ice_sched_assoc_vsi_to_agg()
ice: add profile conflict check for AVF FDIR
ice: Fix ice_cfg_rdma_fltr() to only update relevant fields
ice: fix W=1 headers mismatch
====================
Link: https://lore.kernel.org/r/20230328172035.3904953-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
ieee802154 for net 2023-03-29
Two small fixes this time.
Dongliang Mu removed an unnecessary null pointer check.
Harshit Mogalapalli fixed an int comparison unsigned against signed from a
recent other fix in the ca8210 driver.
* tag 'ieee802154-for-net-2023-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
net: ieee802154: remove an unnecessary null pointer check
ca8210: Fix unsigned mac_len comparison with zero in ca8210_skb_tx()
====================
Link: https://lore.kernel.org/r/20230329064541.2147400-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In gsi_trans_pool_init_dma(), the total size of a pool of memory
used for DMA transactions is calculated. However the calculation is
done incorrectly.
For 4KB pages, this total size is currently always more than one
page, and as a result, the calculation produces a positive (though
incorrect) total size. The code still works in this case; we just
end up with fewer DMA pool entries than we intended.
Bjorn Andersson tested booting a kernel with 16KB pages, and hit a
null pointer derereference in sg_alloc_append_table_from_pages(),
descending from gsi_trans_pool_init_dma(). The cause of this was
that a 16KB total size was going to be allocated, and with 16KB
pages the order of that allocation is 0. The total_size calculation
yielded 0, which eventually led to the crash.
Correcting the total_size calculation fixes the problem.
Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Fixes: 9dd441e4ed ("soc: qcom: ipa: GSI transactions")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328162751.2861791-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code implicitly assumes that the list iterator finds a correct
handle. If 'vsi_handle' is not found the 'old_agg_vsi_info' was
pointing to an bogus memory location. For safety a separate list
iterator variable should be used to make the != NULL check on
'old_agg_vsi_info' correct under any circumstances.
Additionally Linus proposed to avoid any use of the list iterator
variable after the loop, in the attempt to move the list iterator
variable declaration into the macro to avoid any potential misuse after
the loop. Using it in a pointer comparison after the loop is undefined
behavior and should be omitted if possible [1].
Fixes: 37c592062b ("ice: remove the VSI info from previous agg")
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Signed-off-by: Jakob Koschel <jkl820.git@gmail.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add profile conflict check while adding some FDIR rules to avoid
unexpected flow behavior, rules may have conflict including:
IPv4 <---> {IPv4_UDP, IPv4_TCP, IPv4_SCTP}
IPv6 <---> {IPv6_UDP, IPv6_TCP, IPv6_SCTP}
For example, when we create an FDIR rule for IPv4, this rule will work
on packets including IPv4, IPv4_UDP, IPv4_TCP and IPv4_SCTP. But if we
then create an FDIR rule for IPv4_UDP and then destroy it, the first
FDIR rule for IPv4 cannot work on pkt IPv4_UDP then.
To prevent this unexpected behavior, we add restriction in software
when creating FDIR rules by adding necessary profile conflict check.
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation causes ice_vsi_update() to update all VSI
fields based on the cached VSI context. This also assumes that the
ICE_AQ_VSI_PROP_Q_OPT_VALID bit is set. This can cause problems if the
VSI context is not correctly synced by the driver. Fix this by only
updating the fields that correspond to ICE_AQ_VSI_PROP_Q_OPT_VALID.
Also, make sure to save the updated result in the cached VSI context
on success.
Fixes: 348048e724 ("ice: Implement iidc operations")
Co-developed-by: Robert Malz <robertx.malz@intel.com>
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
make modules W=1 returns:
.../ice/ice_txrx_lib.c:448: warning: Function parameter or member 'first_idx' not described in 'ice_finalize_xdp_rx'
.../ice/ice_txrx.c:948: warning: Function parameter or member 'ntc' not described in 'ice_get_rx_buf'
.../ice/ice_txrx.c:1038: warning: Excess function parameter 'rx_buf' description in 'ice_construct_skb'
Fix these warnings by adding and deleting the deviant arguments.
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Fixes: d7956d81f1 ("ice: Pull out next_to_clean bump out of ice_put_rx_buf()")
CC: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The tests for the number of grant mapping or copy operations reaching
the array size of the operations buffer at the end of the main loop in
xenvif_tx_build_gops() isn't needed.
The loop can handle at maximum MAX_PENDING_REQS transfer requests, as
XEN_RING_NR_UNCONSUMED_REQUESTS() is taking unsent responses into
consideration, too.
Remove the tests.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix xenvif_get_requests() not to do grant copy operations across local
page boundaries. This requires to double the maximum number of copy
operations per queue, as each copy could now be split into 2.
Make sure that struct xenvif_tx_cb doesn't grow too large.
Cc: stable@vger.kernel.org
Fixes: ad7f402ae4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In PPPoE add all IPv4 header option length to the parser
and adjust the L3 and L4 offset accordingly.
Currently the L4 match does not work with PPPoE and
all packets are matched as L3 IP4 OPT.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The mvpp2 parser entry for QinQ has the inner and outer VLAN
in the wrong order.
Fix the problem by swapping them.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The blamed commit has introduced the following tests to
dwmac4_add_hw_vlan_rx_fltr(), called from stmmac_vlan_rx_add_vid():
if (hw->promisc) {
netdev_err(dev,
"Adding VLAN in promisc mode not supported\n");
return -EPERM;
}
"VLAN promiscuous" mode is keyed in this driver to IFF_PROMISC, and so,
vlan_vid_add() and vlan_vid_del() calls cannot take place in IFF_PROMISC
mode. I have the following 2 arguments that this restriction is.... hm,
how shall I put it nicely... unproductive :)
First, take the case of a Linux bridge. If the kernel is compiled with
CONFIG_BRIDGE_VLAN_FILTERING=y, then this bridge shall have a VLAN
database. The bridge shall try to call vlan_add_vid() on its bridge
ports for each VLAN in the VLAN table. It will do this irrespectively of
whether that port is *currently* VLAN-aware or not. So it will do this
even when the bridge was created with vlan_filtering 0.
But the Linux bridge, in VLAN-unaware mode, configures its ports in
promiscuous (IFF_PROMISC) mode, so that they accept packets with any
MAC DA (a switch must do this in order to forward those packets which
are not directly targeted to its MAC address).
As a result, the stmmac driver does not work as a bridge port, when the
kernel is compiled with CONFIG_BRIDGE_VLAN_FILTERING=y.
$ ip link add br0 type bridge && ip link set br0 up
$ ip link set eth0 master br0 && ip link set eth0 up
[ 2333.943296] br0: port 1(eth0) entered blocking state
[ 2333.943381] br0: port 1(eth0) entered disabled state
[ 2333.943782] device eth0 entered promiscuous mode
[ 2333.944080] 4033c000.ethernet eth0: Adding VLAN in promisc mode not supported
[ 2333.976509] 4033c000.ethernet eth0: failed to initialize vlan filtering on this port
RTNETLINK answers: Operation not permitted
Secondly, take the case of stmmac as DSA master. Some switch tagging
protocols are based on 802.1Q VLANs (tag_sja1105.c), and as such,
tag_8021q.c uses vlan_vid_add() to work with VLAN-filtering DSA masters.
But also, when a DSA port becomes promiscuous (for example when it joins
a bridge), the DSA framework also makes the DSA master promiscuous.
Moreover, for every VLAN that a DSA switch sends to the CPU, DSA also
programs a VLAN filter on the DSA master, because if the the DSA switch
uses a tail tag, then the hardware frame parser of the DSA master will
see VLAN as VLAN, and might filter them out, for being unknown.
Due to the above 2 reasons, my belief is that the stmmac driver does not
get to choose to not accept vlan_vid_add() calls while IFF_PROMISC is
enabled, because the 2 are completely independent and there are code
paths in the network stack which directly lead to this situation
occurring, without the user's direct input.
In fact, my belief is that "VLAN promiscuous" mode should have never
been keyed on IFF_PROMISC in the first place, but rather, on the
NETIF_F_HW_VLAN_CTAG_FILTER feature flag which can be toggled by the
user through ethtool -k, when present in netdev->hw_features.
In the stmmac driver, NETIF_F_HW_VLAN_CTAG_FILTER is only present in
"features", making this feature "on [fixed]".
I have this belief because I am unaware of any definition of promiscuity
which implies having an effect on anything other than MAC DA (therefore
not VLAN). However, I seem to be rather alone in having this opinion,
looking back at the disagreements from this discussion:
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
In any case, to remove the vlan_vid_add() dependency on !IFF_PROMISC,
one would need to remove the check and see what fails. I guess the test
was there because of the way in which dwmac4_vlan_promisc_enable() is
implemented.
For context, the dwmac4 supports Perfect Filtering for a limited number
of VLANs - dwmac4_get_num_vlan(), priv->hw->num_vlan, with a fallback on
Hash Filtering - priv->dma_cap.vlhash - see stmmac_vlan_update(), also
visible in cat /sys/kernel/debug/stmmaceth/eth0/dma_cap | grep 'VLAN
Hash Filtering'.
The perfect filtering is based on MAC_VLAN_Tag_Filter/MAC_VLAN_Tag_Data
registers, accessed in the driver through dwmac4_write_vlan_filter().
The hash filtering is based on the MAC_VLAN_Hash_Table register, named
GMAC_VLAN_HASH_TABLE in the driver and accessed by dwmac4_update_vlan_hash().
The control bit for enabling hash filtering is GMAC_VLAN_VTHM
(MAC_VLAN_Tag_Ctrl bit VTHM: VLAN Tag Hash Table Match Enable).
Now, the description of dwmac4_vlan_promisc_enable() is that it iterates
through the driver's cache of perfect filter entries (hw->vlan_filter[i],
added by dwmac4_add_hw_vlan_rx_fltr()), and evicts them from hardware by
unsetting their GMAC_VLAN_TAG_DATA_VEN (MAC_VLAN_Tag_Data bit VEN - VLAN
Tag Enable) bit. Then it unsets the GMAC_VLAN_VTHM bit, which disables
hash matching.
This leaves the MAC, according to table "VLAN Match Status" from the
documentation, to always enter these data paths:
VID |VLAN Perfect Filter |VTHM Bit |VLAN Hash Filter |Final VLAN Match
|Match Result | |Match Result |Status
-------|--------------------|---------|-----------------|----------------
VID!=0 |Fail |0 |don't care |Pass
So, dwmac4_vlan_promisc_enable() does its job, but by unsetting
GMAC_VLAN_VTHM, it conflicts with the other code path which controls
this bit: dwmac4_update_vlan_hash(), called through stmmac_update_vlan_hash()
from stmmac_vlan_rx_add_vid() and from stmmac_vlan_rx_kill_vid().
This is, I guess, why dwmac4_add_hw_vlan_rx_fltr() is not allowed to run
after dwmac4_vlan_promisc_enable() has unset GMAC_VLAN_VTHM: because if
it did, then dwmac4_update_vlan_hash() would set GMAC_VLAN_VTHM again,
breaking the "VLAN promiscuity".
It turns out that dwmac4_vlan_promisc_enable() is way too complicated
for what needs to be done. The MAC_Packet_Filter register also has the
VTFE bit (VLAN Tag Filter Enable), which simply controls whether VLAN
tagged packets which don't match the filtering tables (either perfect or
hash) are dropped or not. At the moment, this driver unconditionally
sets GMAC_PACKET_FILTER_VTFE if NETIF_F_HW_VLAN_CTAG_FILTER was detected
through the priv->dma_cap.vlhash capability bits of the device, in
stmmac_dvr_probe().
I would suggest deleting the unnecessarily complex logic from
dwmac4_vlan_promisc_enable(), and simply unsetting GMAC_PACKET_FILTER_VTFE
when becoming IFF_PROMISC, which has the same effect of allowing packets
with any VLAN tags, but has the additional benefit of being able to run
concurrently with stmmac_vlan_rx_add_vid() and stmmac_vlan_rx_kill_vid().
As much as I believe that the VTFE bit should have been exclusively
controlled by NETIF_F_HW_VLAN_CTAG_FILTER through ethtool, and not by
IFF_PROMISC, changing that is not a punctual fix to the problem, and it
would probably break the VFFQ feature added by the later commit
e0f9956a38 ("net: stmmac: Add option for VLAN filter fail queue
enable"). From the commit description, VFFQ needs IFF_PROMISC=on and
VTFE=off in order to work (and this change respects that). But if VTFE
was changed to be controlled through ethtool -k, then a user-visible
change would have been introduced in Intel's scripts (a need to run
"ethtool -k eth0 rx-vlan-filter off" which did not exist before).
The patch was tested with this set of commands:
ip link set eth0 up
ip link add link eth0 name eth0.100 type vlan id 100
ip addr add 192.168.100.2/24 dev eth0.100 && ip link set eth0.100 up
ip link set eth0 promisc on
ip link add link eth0 name eth0.101 type vlan id 101
ip addr add 192.168.101.2/24 dev eth0.101 && ip link set eth0.101 up
ip link set eth0 promisc off
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link set eth0 promisc on
ping -c 5 192.168.100.1
ping -c 5 192.168.101.1
ip link del eth0.100
ip link del eth0.101
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we should see them
ip link set eth0 promisc off
# Wait for VLAN-tagged pings from the other end...
# Check with "tcpdump -i eth0 -e -n -p" and we shouldn't see them
# anymore, but remove the "-p" argument from tcpdump and they're there.
Fixes: c89f44ff10 ("net: stmmac: Add support for VLAN promiscuous mode")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9131RNX incorrectly shows EEE capabilities in its registers.
Although the "EEE control and capability 1" (Register 3.20) is set to 0,
indicating no EEE support, the "EEE advertisement 1" (Register 7.60) is
set to 0x6, advertising EEE support for 1000BaseT/Full and
100BaseT/Full.
This inconsistency causes PHYlib to assume there is no EEE support,
preventing control over EEE advertisement, which is enabled by default.
This patch resolves the issue by utilizing the ksz9477_get_features()
function to correctly set the EEE capabilities for the KSZ9131RNX. This
adjustment allows proper control over EEE advertisement and ensures
accurate representation of the device's capabilities.
Fixes: 8b68710a31 ("net: phy: start using genphy_c45_ethtool_get/set_eee()")
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failover txq is inited as 16 queues.
when a packet is transmitted from the failover device firstly,
the failover device will select the queue which is returned from
the primary device if the primary device is UP and running.
If the primary device txq is bigger than the default 16,
it can lead to the following warning:
eth0 selects TX queue 18, but real number of TX queues is 16
The warning backtrace is:
[ 32.146376] CPU: 18 PID: 9134 Comm: chronyd Tainted: G E 6.2.8-1.el7.centos.x86_64 #1
[ 32.147175] Hardware name: Red Hat KVM, BIOS 1.10.2-3.el7_4.1 04/01/2014
[ 32.147730] Call Trace:
[ 32.147971] <TASK>
[ 32.148183] dump_stack_lvl+0x48/0x70
[ 32.148514] dump_stack+0x10/0x20
[ 32.148820] netdev_core_pick_tx+0xb1/0xe0
[ 32.149180] __dev_queue_xmit+0x529/0xcf0
[ 32.149533] ? __check_object_size.part.0+0x21c/0x2c0
[ 32.149967] ip_finish_output2+0x278/0x560
[ 32.150327] __ip_finish_output+0x1fe/0x2f0
[ 32.150690] ip_finish_output+0x2a/0xd0
[ 32.151032] ip_output+0x7a/0x110
[ 32.151337] ? __pfx_ip_finish_output+0x10/0x10
[ 32.151733] ip_local_out+0x5e/0x70
[ 32.152054] ip_send_skb+0x19/0x50
[ 32.152366] udp_send_skb.isra.0+0x163/0x3a0
[ 32.152736] udp_sendmsg+0xba8/0xec0
[ 32.153060] ? __folio_memcg_unlock+0x25/0x60
[ 32.153445] ? __pfx_ip_generic_getfrag+0x10/0x10
[ 32.153854] ? sock_has_perm+0x85/0xa0
[ 32.154190] inet_sendmsg+0x6d/0x80
[ 32.154508] ? inet_sendmsg+0x6d/0x80
[ 32.154838] sock_sendmsg+0x62/0x70
[ 32.155152] ____sys_sendmsg+0x134/0x290
[ 32.155499] ___sys_sendmsg+0x81/0xc0
[ 32.155828] ? _get_random_bytes.part.0+0x79/0x1a0
[ 32.156240] ? ip4_datagram_release_cb+0x5f/0x1e0
[ 32.156649] ? get_random_u16+0x69/0xf0
[ 32.156989] ? __fget_light+0xcf/0x110
[ 32.157326] __sys_sendmmsg+0xc4/0x210
[ 32.157657] ? __sys_connect+0xb7/0xe0
[ 32.157995] ? __audit_syscall_entry+0xce/0x140
[ 32.158388] ? syscall_trace_enter.isra.0+0x12c/0x1a0
[ 32.158820] __x64_sys_sendmmsg+0x24/0x30
[ 32.159171] do_syscall_64+0x38/0x90
[ 32.159493] entry_SYSCALL_64_after_hwframe+0x72/0xdc
Fix that by reducing txq number as the non-existent primary-dev does.
Fixes: cfc80d9a11 ("net: Introduce net_failover driver")
Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link speed is 10 Mbps and temperature is under -20°C, RTL8168H and
RTL8107E may have rx crc error. Disable phy 10 Mbps pll off to fix this
issue.
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e10 ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, vmxnet3 uses GRO callback only if LRO is disabled. However,
on smartNic based setups where UPT is supported, LRO can be enabled
from guest VM but UPT devicve does not support LRO as of now. In such
cases, there can be performance degradation as GRO is not being done.
This patch fixes this issue by calling GRO API when UPT is enabled. We
use updateRxProd to determine if UPT mode is active or not.
To clarify few things discussed over the thread:
The patch is not neglecting any feature bits nor disabling GRO. It uses
GRO callback when UPT is active as LRO is not available in UPT.
GRO callback cannot be used as default for all cases as it degrades
performance for non-UPT cases or for cases when LRO is already done in
ESXi.
Cc: stable@vger.kernel.org
Fixes: 6f91f4ba04 ("vmxnet3: add support for capability registers")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323200721.27622-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent.
Fixes: aac9400106 ("net: dsa: realtek: add new mdio interface for drivers")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230323103735.2331786-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dp83869 internally uses a look-up table for mapping supported delays in
nanoseconds to register values.
When specific delays are defined in device-tree, phy_get_internal_delay
does the lookup automatically returning an index.
The default case wrongly assigns the nanoseconds value from the lookup
table, resulting in numeric value 2000 applied to delay configuration
register, rather than the expected index values 0-7 (7 for 2000).
Ultimately this issue broke RX for 1Gbps links.
Fix default delay configuration by assigning the intended index value
directly.
Cc: stable@vger.kernel.org
Fixes: 736b25afe2 ("net: dp83869: Add RGMII internal delay configuration")
Co-developed-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230323102536.31988-1-josua@solid-run.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At NIC reset, some offload features related to encapsulated traffic
might have changed (this mainly happens if the firmware-variant is
changed with the sfboot userspace tool). Because of this, features are
checked and set again at reset time.
However, this was not done right, and some features were improperly
overwritten at NIC reset:
- Tunneled IPv6 segmentation was always disabled
- Features disabled with ethtool were reenabled
- Features that becomes unsupported after the reset were not disabled
Also, checking if the device supports IPV6_CSUM to enable TSO6 is no
longer necessary because all currently supported devices support it.
Additionally, move the assignment of some other features to the
EF10_OFFLOAD_FEATURES macro, like it is done in ef100, leaving the
selection of features in efx_pci_probe_post_io a bit cleaner.
Fixes: ffffd2454a ("sfc: correctly advertise tunneled IPv6 segmentation")
Fixes: 24b2c3751a ("sfc: advertise encapsulated offloads on EF10")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Suggested-by: Jonathan Cooper <jonathan.s.cooper@amd.com>
Tested-by: Jonathan Cooper <jonathan.s.cooper@amd.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230323083417.7345-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2023-03-23
We've added 8 non-merge commits during the last 13 day(s) which contain
a total of 21 files changed, 238 insertions(+), 161 deletions(-).
The main changes are:
1) Fix verification issues in some BPF programs due to their stack usage
patterns, from Eduard Zingerman.
2) Fix to add missing overflow checks in xdp_umem_reg and return an error
in such case, from Kal Conley.
3) Fix and undo poisoning of strlcpy in libbpf given it broke builds for
libcs which provided the former like uClibc-ng, from Jesus Sanchez-Palencia.
4) Fix insufficient bpf_jit_limit default to avoid users running into hard
to debug seccomp BPF errors, from Daniel Borkmann.
5) Fix driver return code when they don't support a bpf_xdp_metadata kfunc
to make it unambiguous from other errors, from Jesper Dangaard Brouer.
6) Two BPF selftest fixes to address compilation errors from recent changes
in kernel structures, from Alexei Starovoitov.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
xdp: bpf_xdp_metadata use EOPNOTSUPP for no driver support
bpf: Adjust insufficient default bpf_jit_limit
xsk: Add missing overflow check in xdp_umem_reg
selftests/bpf: Fix progs/test_deny_namespace.c issues.
selftests/bpf: Fix progs/find_vma_fail1.c build error.
libbpf: Revert poisoning of strlcpy
selftests/bpf: Tests for uninitialized stack reads
bpf: Allow reads from uninit stack
====================
Link: https://lore.kernel.org/r/20230323225221.6082-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalle Valo says:
====================
wireless fixes for v6.3
Third set of fixes for v6.3. mt76 has two kernel crash fixes and
adding back 160 MHz channel support for mt7915. mac80211 has fixes for
a race in transmit path and two mesh related fixes. iwlwifi also has
fixes for races.
* tag 'wireless-2023-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix mesh path discovery based on unicast packets
wifi: mac80211: fix qos on mesh interfaces
wifi: iwlwifi: mvm: protect TXQ list manipulation
wifi: iwlwifi: mvm: fix mvmtxq->stopped handling
wifi: mac80211: Serialize ieee80211_handle_wake_tx_queue()
wifi: mwifiex: mark OF related data as maybe unused
wifi: mt76: connac: do not check WED status for non-mmio devices
wifi: mt76: mt7915: add back 160MHz channel width support for MT7915
wifi: mt76: do not run mt76_unregister_device() on unregistered hw
====================
Link: https://lore.kernel.org/r/20230323110332.C4FE4C433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In device_for_each_child_node(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 fixes 2023-03-21
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: E-Switch, Fix an Oops in error handling code
net/mlx5: Read the TC mapping of all priorities on ETS query
net/mlx5e: Overcome slow response for first macsec ASO WQE
net/mlx5e: Initialize link speed to zero
net/mlx5: Fix steering rules cleanup
net/mlx5e: Block entering switchdev mode with ns inconsistency
net/mlx5e: Set uplink rep as NETNS_LOCAL
====================
Link: https://lore.kernel.org/r/20230321211135.47711-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (ice)
This series contains updates to ice driver only.
Piotr sets first_desc field for proper handling of Flow Director
packets.
Michal moves error checking for VF earlier in function to properly return
error before other checks/reporting; he also corrects VSI filter removal to
be done during VSI removal and not rebuild.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: remove filters only if VSI is deleted
ice: check if VF exists before mode check
ice: fix rx buffers handling for flow director packets
====================
Link: https://lore.kernel.org/r/20230321183641.2849726-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
