Both in RX and TX, the traffic that performs IPsec packet offload
transformation is accounted by HW. It is needed to properly handle
hard limits that require to drop the packet.
It means that XFRM core needs to update internal counters with the one
that accounted by the HW, so new callbacks are introduced in this patch.
In case of soft or hard limit is occurred, the driver should call to
xfrm_state_check_expire() that will perform key rekeying exactly as
done by XFRM core.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Traffic received by device with enabled IPsec packet offload should
be forwarded to the stack only after decryption, packet headers and
trailers removed.
Such packets are expected to be seen as normal (non-XFRM) ones, while
not-supported packets should be dropped by the HW.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Extend netlink interface to add and delete XFRM policy from the device.
This functionality is a first step to implement packet IPsec offload solution.
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In the next patches, the xfrm core code will be extended to support
new type of offload - packet offload. In that mode, both policy and state
should be specially configured in order to perform whole offloaded data
path.
Full offload takes care of encryption, decryption, encapsulation and
other operations with headers.
As this mode is new for XFRM policy flow, we can "start fresh" with flag
bits and release first and second bit for future use.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Kalle Valo says:
====================
wireless-next patches for v6.2
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
- store WLAN firmware version in SMEM image table
mt76
- mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
- mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
- mt7915: add ack signal support
- mt7915: enable coredump support
- mt7921: remain_on_channel support
- mt7921: channel context support
iwlwifi
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
* tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (144 commits)
wifi: ath10k: fix QCOM_SMEM dependency
wifi: mt76: mt7921e: add pci .shutdown() support
wifi: mt76: mt7915: mmio: fix naming convention
wifi: mt76: mt7996: add support to configure spatial reuse parameter set
wifi: mt76: mt7996: enable ack signal support
wifi: mt76: mt7996: enable use_cts_prot support
wifi: mt76: mt7915: rely on band_idx of mt76_phy
wifi: mt76: mt7915: enable per bandwidth power limit support
wifi: mt76: mt7915: introduce mt7915_get_power_bound()
mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
wifi: mt76: mt7915: fix band_idx usage
wifi: mt76: mt7915: enable .sta_set_txpwr support
wifi: mt76: mt7915: add basedband Txpower info into debugfs
wifi: mt76: mt7915: add support to configure spatial reuse parameter set
wifi: mt76: mt7915: add missing MODULE_PARM_DESC
...
====================
Link: https://lore.kernel.org/r/20221202214254.D0D3DC433C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 9ed7bfc795 ("sctp: fix memory leak in
sctp_stream_outq_migrate()"), sctp_sched_set_sched() is the only
place calling sched->free(), and it can actually be replaced by
sched->free_sid() on each stream, and yet there's already a loop
to traverse all streams in sctp_sched_set_sched().
This patch adds a function sctp_sched_free_sched() where it calls
sched->free_sid() for each stream to replace sched->free() calls
in sctp_sched_set_sched() and then deletes the unused free member
from struct sctp_sched_ops.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/e10aac150aca2686cb0bd0570299ec716da5a5c0.1669849471.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To do that, separate two scenarios:
- where it's the first MD5 key on the system, which means that enabling
of the static key may need to sleep;
- copying of an existing key from a listening socket to the request
socket upon receiving a signed TCP segment, where static key was
already enabled (when the key was added to the listening socket).
Now the life-time of the static branch for TCP-MD5 is until:
- last tcp_md5sig_info is destroyed
- last socket in time-wait state with MD5 key is closed.
Which means that after all sockets with TCP-MD5 keys are gone, the
system gets back the performance of disabled md5-key static branch.
While at here, provide static_key_fast_inc() helper that does ref
counter increment in atomic fashion (without grabbing cpus_read_lock()
on CONFIG_JUMP_LABEL=y). This is needed to add a new user for
a static_key when the caller controls the lifetime of another user.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This can be used to selectively disable feature flags for checksum offload,
scatter/gather or GSO by changing vif->netdev_features.
Removing features from vif->netdev_features does not affect the netdev
features themselves, but instead fixes up skbs in the tx path so that the
offloads are not needed in the driver.
Aside from making it easier to deal with vif type based hardware limitations,
this also makes it possible to optimize performance on hardware without native
GSO support by declaring GSO support in hw->netdev_features and removing it
from vif->netdev_features. This allows mac80211 to handle GSO segmentation
after the sta lookup, but before itxq enqueue, thus reducing the number of
unnecessary sta lookups, as well as some other per-packet processing.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221010094338.78070-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To read from a region, user space must currently request a new snapshot of
the region and then read from that snapshot. This can sometimes be overkill
if user space only reads a tiny portion. They first create the snapshot,
then request a read, then destroy the snapshot.
For regions which have a single underlying "contents", it makes sense to
allow supporting direct reading of the region data.
Extend the DEVLINK_CMD_REGION_READ to allow direct reading from a region if
requested via the new DEVLINK_ATTR_REGION_DIRECT. If this attribute is set,
then perform a direct read instead of using a snapshot. Direct read is
mutually exclusive with DEVLINK_ATTR_REGION_SNAPSHOT_ID, and care is taken
to ensure that we reject commands which provide incorrect attributes.
Regions must enable support for direct read by implementing the .read()
callback function. If a region does not support such direct reads, a
suitable extended error message is reported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steffen Klassert says:
====================
ipsec-next 2022-11-26
1) Remove redundant variable in esp6.
From Colin Ian King.
2) Update x->lastused for every packet. It was used only for
outgoing mobile IPv6 packets, but showed to be usefull
to check if the a SA is still in use in general.
From Antony Antony.
3) Remove unused variable in xfrm_byidx_resize.
From Leon Romanovsky.
4) Finalize extack support for xfrm.
From Sabrina Dubroca.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: add extack to xfrm_set_spdinfo
xfrm: add extack to xfrm_alloc_userspi
xfrm: add extack to xfrm_do_migrate
xfrm: add extack to xfrm_new_ae and xfrm_replay_verify_len
xfrm: add extack to xfrm_del_sa
xfrm: add extack to xfrm_add_sa_expire
xfrm: a few coding style clean ups
xfrm: Remove not-used total variable
xfrm: update x->lastused for every packet
esp6: remove redundant variable err
====================
Link: https://lore.kernel.org/r/20221126110303.1859238-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tag_8021q definitions are all over the place. Some are exported to
linux/dsa/8021q.h (visible by DSA core, taggers, switch drivers and
everyone else), and some are in dsa_priv.h.
Move the structures that don't need external visibility into tag_8021q.c,
and the ones which don't need the world or switch drivers to see them
into tag_8021q.h.
We also have the tag_8021q.h inclusion from switch.c, which is basically
the entire reason why tag_8021q.c was built into DSA in commit
8b6e638b4b ("net: dsa: build tag_8021q.c as part of DSA core").
I still don't know how to better deal with that, so leave it alone.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dsa.o and dsa2.o are linked into the same dsa_core.o, there is no reason
to export this symbol when its only caller is local.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When we call connect() for a socket bound to a wildcard address, we update
saddr locklessly. However, it could result in a data race; another thread
iterating over bhash might see a corrupted address.
Let's update saddr under the bhash bucket's lock.
Fixes: 3df80d9320 ("[DCCP]: Introduce DCCPv6")
Fixes: 7c657876b6 ("[DCCP]: Initial implementation")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Endpoint creation can fail for a number of reasons; in case of failure
append the error number to the extended ack message, using a newly
introduced generic helper.
Additionally let mptcp_pm_nl_append_new_local_addr() report different
error reasons.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of del_timer_sync must prevent restarting of the timer, If
we have no this synchronization, there is a small probability that the
cancellation will not be successful.
And syzbot report the fellowing crash:
==================================================================
BUG: KASAN: use-after-free in hlist_add_head include/linux/list.h:929 [inline]
BUG: KASAN: use-after-free in enqueue_timer+0x18/0xa4 kernel/time/timer.c:605
Write at addr f9ff000024df6058 by task syz-fuzzer/2256
Pointer tag: [f9], memory tag: [fe]
CPU: 1 PID: 2256 Comm: syz-fuzzer Not tainted 6.1.0-rc5-syzkaller-00008-
ge01d50cbd6ee #0
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0 arch/arm64/kernel/stacktrace.c:156
dump_backtrace arch/arm64/kernel/stacktrace.c:162 [inline]
show_stack+0x18/0x40 arch/arm64/kernel/stacktrace.c:163
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x68/0x84 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x1a8/0x4a0 mm/kasan/report.c:395
kasan_report+0x94/0xb4 mm/kasan/report.c:495
__do_kernel_fault+0x164/0x1e0 arch/arm64/mm/fault.c:320
do_bad_area arch/arm64/mm/fault.c:473 [inline]
do_tag_check_fault+0x78/0x8c arch/arm64/mm/fault.c:749
do_mem_abort+0x44/0x94 arch/arm64/mm/fault.c:825
el1_abort+0x40/0x60 arch/arm64/kernel/entry-common.c:367
el1h_64_sync_handler+0xd8/0xe4 arch/arm64/kernel/entry-common.c:427
el1h_64_sync+0x64/0x68 arch/arm64/kernel/entry.S:576
hlist_add_head include/linux/list.h:929 [inline]
enqueue_timer+0x18/0xa4 kernel/time/timer.c:605
mod_timer+0x14/0x20 kernel/time/timer.c:1161
mrp_periodic_timer_arm net/802/mrp.c:614 [inline]
mrp_periodic_timer+0xa0/0xc0 net/802/mrp.c:627
call_timer_fn.constprop.0+0x24/0x80 kernel/time/timer.c:1474
expire_timers+0x98/0xc4 kernel/time/timer.c:1519
To fix it, we can introduce a new active flags to make sure the timer will
not restart.
Reported-by: syzbot+6fd64001c20aa99e34a4@syzkaller.appspotmail.com
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-next patches for v6.2
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch at first adds a pernet global l3mdev_accept to decide if it
accepts the packets from a l3mdev when a SCTP socket doesn't bind to
any interface. It's set to 1 to avoid any possible incompatible issue,
and in next patch, a sysctl will be introduced to allow to change it.
Then similar to inet/udp_sk_bound_dev_eq(), sctp_sk_bound_dev_eq() is
added to check either dif or sdif is equal to sk_bound_dev_if, and to
check sid is 0 or l3mdev_accept is 1 if sk_bound_dev_if is not set.
This function is used to match a association or a endpoint, namely
called by sctp_addrs_lookup_transport() and sctp_endpoint_is_match().
All functions that needs updating are:
sctp_rcv():
asoc:
__sctp_rcv_lookup()
__sctp_lookup_association() -> sctp_addrs_lookup_transport()
__sctp_rcv_lookup_harder()
__sctp_rcv_init_lookup()
__sctp_lookup_association() -> sctp_addrs_lookup_transport()
__sctp_rcv_walk_lookup()
__sctp_rcv_asconf_lookup()
__sctp_lookup_association() -> sctp_addrs_lookup_transport()
ep:
__sctp_rcv_lookup_endpoint() -> sctp_endpoint_is_match()
sctp_connect():
sctp_endpoint_is_peeled_off()
__sctp_lookup_association()
sctp_has_association()
sctp_lookup_association()
__sctp_lookup_association() -> sctp_addrs_lookup_transport()
sctp_diag_dump_one():
sctp_transport_lookup_process() -> sctp_addrs_lookup_transport()
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb_sdif function in struct sctp_af to get the enslaved device
for both ipv4 and ipv6 when adding SCTP VRF support in sctp_rcv in
the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ff4eb3d5e ("neighbour: make proxy_queue.qlen limit
per-device") introduced the length counter qlen in struct neigh_parms.
There are separate neigh_parms instances for IPv4/ARP and IPv6/ND, and
while the family specific qlen is incremented in pneigh_enqueue(), the
mentioned commit decrements always the IPv4/ARP specific qlen,
regardless of the currently processed family, in pneigh_queue_purge()
and neigh_proxy_process().
As a result, with IPv6/ND, the family specific qlen is only incremented
(and never decremented) until it exceeds PROXY_QLEN, and then, according
to the check in pneigh_enqueue(), neighbor solicitations are not
answered anymore. As an example, this is noted when using the
subnet-router anycast address to access a Linux router. After a certain
amount of time (in the observed case, qlen exceeded PROXY_QLEN after two
days), the Linux router stops answering neighbor solicitations for its
subnet-router anycast address and effectively becomes unreachable.
Another result with IPv6/ND is that the IPv4/ARP specific qlen is
decremented more often than incremented. This leads to negative qlen
values, as a signed integer has been used for the length counter qlen,
and potentially to an integer overflow.
Fix this by introducing the helper function neigh_parms_qlen_dec(),
which decrements the family specific qlen. Thereby, make use of the
existing helper function neigh_get_dev_parms_rcu(), whose definition
therefore needs to be placed earlier in neighbour.c. Take the family
member from struct neigh_table to determine the currently processed
family and appropriately call neigh_parms_qlen_dec() from
pneigh_queue_purge() and neigh_proxy_process().
Additionally, use an unsigned integer for the length counter qlen.
Fixes: 0ff4eb3d5e ("neighbour: make proxy_queue.qlen limit per-device")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver is able to create leaf nodes for the devlink-rate,
but is unable to set parent for them. This wasn't as issue before the
possibility to export hierarchy from the driver. After adding the export
feature, in order for the driver to supply correct hierarchy, it's
necessary for it to be able to supply a parent name to
devl_rate_leaf_create().
Introduce a new parameter 'parent_name' in devl_rate_leaf_create().
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Intel 100G card internal firmware hierarchy for Hierarchicial QoS is very
rigid and can't be easily removed. This requires an ability to export
default hierarchy to allow user to modify it. Currently the driver is
only able to create the 'leaf' nodes, which usually represent the vport.
This is not enough for HQoS implemented in Intel hardware.
Introduce new function devl_rate_node_create() that allows for creation
of the devlink-rate nodes from the driver.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To fully utilize offload capabilities of Intel 100G card QoS capabilities
new attribute 'tx_weight' needs to be introduced. This attribute allows
for usage of Weighted Fair Queuing arbitration scheme among siblings.
This arbitration scheme can be used simultaneously with the strict
priority.
Introduce new attribute in devlink-rate that will allow for configuration
of Weighted Fair Queueing. New attribute is optional.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To fully utilize offload capabilities of Intel 100G card QoS capabilities
new attribute 'tx_priority' needs to be introduced. This attribute allows
for usage of strict priority arbiter among siblings. This arbitration
scheme attempts to schedule nodes based on their priority as long as the
nodes remain within their bandwidth limit.
Introduce new attribute in devlink-rate that will allow for configuration
of strict priority. New attribute is optional.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DSA tagging protocol driver macros are in the public include/net/dsa.h
probably because that's also where the DSA_TAG_PROTO_*_VALUE macros are
(MODULE_ALIAS_DSA_TAG_DRIVER hinges on those macro definitions).
But there is no reason to expose these helpers to <net/dsa.h>. That
header is shared between switch drivers (drivers/net/dsa/), tagging
protocol drivers (net/dsa/tag_*.c), the DSA core (net/dsa/ sans tag_*.c),
and the rest of the world (DSA master drivers, network stack, etc).
Too much exposure.
On the other hand, net/dsa/dsa_priv.h is included only by the DSA core
and by DSA tagging protocol drivers (or IOW, "friend" modules). Also a
bit too much exposure - I've contemplated creating a new header which is
only included by tagging protocol drivers, but completely separating a
new dsa_tag_proto.h from dsa_priv.h is not immediately trivial - for
example dsa_slave_to_port() is used both from the fast path and from the
control path.
So for now, move these definitions to dsa_priv.h which at least hides
them from the world.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kernel test robot reported warnings when build bonding module with
make W=1 O=build_dir ARCH=x86_64 SHELL=/bin/bash drivers/net/bonding/:
from ../drivers/net/bonding/bond_main.c:35:
In function ‘fortify_memcpy_chk’,
inlined from ‘iph_to_flow_copy_v4addrs’ at ../include/net/ip.h:566:2,
inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3984:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘fortify_memcpy_chk’,
inlined from ‘iph_to_flow_copy_v6addrs’ at ../include/net/ipv6.h:900:2,
inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3994:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is because we try to copy the whole ip/ip6 address to the flow_key,
while we only point the to ip/ip6 saddr. Note that since these are UAPI
headers, __struct_group() is used to avoid the compiler warnings.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c3f8324188 ("net: Add full IPv6 addresses to flow_keys")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20221115142400.1204786-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
sk->sk_user_data has multiple users, which are not compatible with each
other. Writers must synchronize by grabbing the sk->sk_callback_lock.
l2tp currently fails to grab the lock when modifying the underlying tunnel
socket fields. Fix it by adding appropriate locking.
We err on the side of safety and grab the sk_callback_lock also inside the
sk_destruct callback overridden by l2tp, even though there should be no
refs allowing access to the sock at the time when sk_destruct gets called.
v4:
- serialize write to sk_user_data in l2tp sk_destruct
v3:
- switch from sock lock to sk_callback_lock
- document write-protection for sk_user_data
v2:
- update Fixes to point to origin of the bug
- use real names in Reported/Tested-by tags
Cc: Tom Parkin <tparkin@katalix.com>
Fixes: 3557baabf2 ("[L2TP]: PPP over L2TP driver core")
Reported-by: Haowei Yan <g1042620637@gmail.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long standing KCSAN issues are caused by data-race around
some dev->stats changes.
Most performance critical paths already use per-cpu
variables, or per-queue ones.
It is reasonable (and more correct) to use atomic operations
for the slow paths.
This patch adds an union for each field of net_device_stats,
so that we can convert paths that are not yet protected
by a spinlock or a mutex.
netdev_stats_to_stats64() no longer has an #if BITS_PER_LONG==64
Note that the memcpy() we were using on 64bit arches
had no provision to avoid load-tearing,
while atomic_long_read() is providing the needed protection
at no cost.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum hash table size is 64K due to the nature of the protocol. [0]
It's smaller than TCP, and fewer sockets can cause a performance drop.
On an EC2 c5.24xlarge instance (192 GiB memory), after running iperf3 in
different netns, creating 32Mi sockets without data transfer in the root
netns causes regression for the iperf3's connection.
uhash_entries sockets length Gbps
64K 1 1 5.69
1Mi 16 5.27
2Mi 32 4.90
4Mi 64 4.09
8Mi 128 2.96
16Mi 256 2.06
32Mi 512 1.12
The per-netns hash table breaks the lengthy lists into shorter ones. It is
useful on a multi-tenant system with thousands of netns. With smaller hash
tables, we can look up sockets faster, isolate noisy neighbours, and reduce
lock contention.
The max size of the per-netns table is 64K as well. This is because the
possible hash range by udp_hashfn() always fits in 64K within the same
netns and we cannot make full use of the whole buckets larger than 64K.
/* 0 < num < 64K -> X < hash < X + 64K */
(num + net_hash_mix(net)) & mask;
Also, the min size is 128. We use a bitmap to search for an available
port in udp_lib_get_port(). To keep the bitmap on the stack and not
fire the CONFIG_FRAME_WARN error at build time, we round up the table
size to 128.
The sysctl usage is the same with TCP:
$ dmesg | cut -d ' ' -f 6- | grep "UDP hash"
UDP hash table entries: 65536 (order: 9, 2097152 bytes, vmalloc)
# sysctl net.ipv4.udp_hash_entries
net.ipv4.udp_hash_entries = 65536 # can be changed by uhash_entries
# sysctl net.ipv4.udp_child_hash_entries
net.ipv4.udp_child_hash_entries = 0 # disabled by default
# ip netns add test1
# ip netns exec test1 sysctl net.ipv4.udp_hash_entries
net.ipv4.udp_hash_entries = -65536 # share the global table
# sysctl -w net.ipv4.udp_child_hash_entries=100
net.ipv4.udp_child_hash_entries = 100
# ip netns add test2
# ip netns exec test2 sysctl net.ipv4.udp_hash_entries
net.ipv4.udp_hash_entries = 128 # own a per-netns table with 2^n buckets
We could optimise the hash table lookup/iteration further by removing
the netns comparison for the per-netns one in the future. Also, we
could optimise the sparse udp_hslot layout by putting it in udp_table.
[0]: https://lore.kernel.org/netdev/4ACC2815.7010101@gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon introduce an optional per-netns hash table
for UDP.
This means we cannot use the global sk->sk_prot->h.udp_table
to fetch a UDP hash table.
Instead, set NULL to sk->sk_prot->h.udp_table for UDP and get
a proper table from net->ipv4.udp_table.
Note that we still need sk->sk_prot->h.udp_table for UDP LITE.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When built with Control Flow Integrity, function prototypes between
caller and function declaration must match. These mismatches are visible
at compile time with the new -Wcast-function-type-strict in Clang[1].
Fix a total of 73 warnings like these:
drivers/net/wireless/intersil/orinoco/wext.c:1379:27: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_param *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
IW_HANDLER(SIOCGIWPOWER, (iw_handler)orinoco_ioctl_getpower),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../net/wireless/wext-compat.c:1607:33: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_point *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
[IW_IOCTL_IDX(SIOCSIWGENIE)] = (iw_handler) cfg80211_wext_siwgenie,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/net/wireless/intersil/orinoco/wext.c:1390:27: error: incompatible function pointer types initializing 'const iw_handler' (aka 'int (*const)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') with an expression of type 'int (struct net_device *, struct iw_request_info *, struct iw_param *, char *)' [-Wincompatible-function-pointer-types]
IW_HANDLER(SIOCGIWRETRY, cfg80211_wext_giwretry),
^~~~~~~~~~~~~~~~~~~~~~
The cfg80211 Wireless Extension handler callbacks (iw_handler) use a
union for the data argument. Actually use the union and perform explicit
member selection in the function body instead of having a function
prototype mismatch. There are no resulting binary differences
before/after changes.
These changes were made partly manually and partly with the help of
Coccinelle.
Link: https://github.com/KSPP/linux/issues/234
Link: https://reviews.llvm.org/D134831 [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/a68822bf8dd587988131bb6a295280cb4293f05d.1667934775.git.gustavoars@kernel.org
As of now, no DSA driver uses a custom link mode validation procedure
anymore. So remove this DSA operation and let phylink determine what is
supported based on config->mac_capabilities (if provided by the driver).
Leave a comment why we left the code that we did, and that there is more
work to do.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Fix sparse warning in the new nft_inner expression, reported
by Jakub Kicinski.
2) Incorrect vlan header check in nft_inner, from Peng Wu.
3) Two patches to pass reset boolean to expression dump operation,
in preparation for allowing to reset stateful expressions in rules.
This adds a new NFT_MSG_GETRULE_RESET command. From Phil Sutter.
4) Inconsistent indentation in nft_fib, from Jiapeng Chong.
5) Speed up siphash calculation in conntrack, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: use siphash_4u64
netfilter: rpfilter/fib: clean up some inconsistent indenting
netfilter: nf_tables: Introduce NFT_MSG_GETRULE_RESET
netfilter: nf_tables: Extend nft_expr_ops::dump callback parameters
netfilter: nft_inner: fix return value check in nft_inner_parse_l2l3()
netfilter: nft_payload: use __be16 to store gre version
====================
Link: https://lore.kernel.org/r/20221115095922.139954-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Analogous to NFT_MSG_GETOBJ_RESET, but for rules: Reset stateful
expressions like counters or quotas. The latter two are the only
consumers, adjust their 'dump' callbacks to respect the parameter
introduced earlier.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a 'reset' flag just like with nft_object_ops::dump. This will be
useful to reset "anonymous stateful objects", e.g. simple rule counters.
No functional change intended.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds a new flow_rule_match_arp function that allows drivers
to be able to dissect ARP frames.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long Li says:
====================
Introduce Microsoft Azure Network Adapter (MANA) RDMA driver [netdev prep]
The first 11 patches which modify the MANA Ethernet driver to support
RDMA driver.
* 'mana-shared-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
net: mana: Define data structures for protection domain and memory registration
net: mana: Define data structures for allocating doorbell page from GDMA
net: mana: Define and process GDMA response code GDMA_STATUS_MORE_ENTRIES
net: mana: Define max values for SGL entries
net: mana: Move header files to a common location
net: mana: Record port number in netdev
net: mana: Export Work Queue functions for use by RDMA driver
net: mana: Set the DMA device max segment size
net: mana: Handle vport sharing between devices
net: mana: Record the physical address for doorbell page region
net: mana: Add support for auxiliary device
====================
Link: https://lore.kernel.org/all/1667502990-2559-1-git-send-email-longli@linuxonhyperv.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
