When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: OMAP2+: critical DRA7xx fix for v4.5-rc
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
* tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
Signed-off-by: Olof Johansson <olof@lixom.net>
Errata id: i877
Description:
------------
The RGMII 1000 Mbps Transmit timing is based on the output clock
(rgmiin_txc) being driven relative to the rising edge of an internal
clock and the output control/data (rgmiin_txctl/txd) being driven relative
to the falling edge of an internal clock source. If the internal clock
source is allowed to be static low (i.e., disabled) for an extended period
of time then when the clock is actually enabled the timing delta between
the rising edge and falling edge can change over the lifetime of the
device. This can result in the device switching characteristics degrading
over time, and eventually failing to meet the Data Manual Delay Time/Skew
specs.
To maintain RGMII 1000 Mbps IO Timings, SW should minimize the
duration that the Ethernet internal clock source is disabled. Note that
the device reset state for the Ethernet clock is "disabled".
Other RGMII modes (10 Mbps, 100Mbps) are not affected
Workaround:
-----------
If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps,
SW should minimize the time the Ethernet internal clock source is disabled
to a maximum of 200 hours in a device life cycle. This is done by enabling
the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android)
by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP.
So, do not allow to gate the cpsw clocks using ti,no-idle property in
cpsw node assuming 1000 Mbps is being used all the time. If someone does
not need 1000 Mbps and wants to gate clocks to cpsw, this property needs
to be deleted in their respective board files.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Merge "Second Round of Renesas ARM Based SoC DT Fixes for v4.5" from Simon Horman:
* remove enable prop from HS-USB device node on porter board
* tag 'renesas-dt-fixes2-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: porter: remove enable prop from HS-USB device node
In the final versions of the Porter board (called "PORTER_C") Renesas
decided to get rid of the Maxim Integrated MAX3355 OTG chip and didn't
add any other provision to differ the host/gadget mode, so we'll have to
remove no longer valid "renesas,enable-gpio" property from the HS-USB
device node. Hopefully, the earlier revisions of the board were never
seen in the wild...
Fixes: c794f6a09a ("ARM: shmobile: porter: add HS-USB DT support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Two omap fixes for omaps against v4.5-rc5:
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
* tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for v4.5:
- Drop the bogus interrupt-parent from i.MX6 CAAM node, which leads to
the CAAM IRQs not getting unmasked at the GPC level.
* tag 'imx-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
Signed-off-by: Olof Johansson <olof@lixom.net>
Few fixes for omaps against v4.5-rc3:
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57 ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57 discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
* tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.5 (part 2)
- Fix the missing mtd flash on linkstation lswtgl
- Use unique machine name for the kirkwood ds112 (for Debian flash-kernel tool)
* tag 'mvebu-fixes-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 8e6ebfaa9b.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The tlv320aic3104 codec's master clock is coming from the SoC's CLKOUT2.
Select the SYS_CLK2 (via divider) as parent clock for CLKOUT2 and select
the same clock (SYS_CLK2) for McASP3 AHCLKX clock as well.
SYS_CLK2 is sourced from an external oscillator running 22.5792MHz and it
is coming in to the SoC via the X1_OSC1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3efda00129 ("ARM: dts: am335x: replace gpio-key,wakeup with
wakeup-source property") replaces all the legacy "gpio-key,wakeup" with
the unified "wakeup-source" property to prevent any further copy-paste
duplication.
However couple of use of these legacy property sneaked in during the
merge window. This patch replaces them too.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MTD flash stores u-boot and u-boot environment on linkstation lswtgl.
The latter one can be easily read/write by u-boot-tools package in Debian.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS
devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts
using the same model identifier.
This patch provides a unique model identifier for the
Synology DiskStation DS112.
Fixes: 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The interrupt-parent property is not needed as it is inherited from
the parent bus and in the case of the CAAM node actively points to
the wrong interrupt controller (GIC instead of GPC). This leads to
the CAAM IRQs not getting unmasked at the GPC level, leaving them
unable to wake the CPU from wait mode, potentially impacting
performance of the CAAM unit when CPUidle is enabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Revert commit 7cd6ca770d ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.
and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.
Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec504 ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After 57a38effa5 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here're a few gpio pin related fixes:
- remove pinctrl-0 definition from pinctrl, since those pins are used
in other places such as gpio-fan and regulators.
- keep initial state of power led
- fix for alarm pin of gpio-fan.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr0" pin
- gpio-leds: "lswxl:red:hdderr1" pin
- gpio-fan: low/high/alarm pin
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: e54e4b1b62 ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Renesas ARM Based SoC Fixes for v4.5
Correct extal1 frequency of armadillo800eva board
* tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Signed-off-by: Olof Johansson <olof@lixom.net>
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is required to be able to send multiple messages to the WkupM3
after the mailbox usage logic adjustment in the wkup_m3_ipc driver.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is needed to achieve lower power numbers during CPU idle on
AM33xx.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
Pull ARM SoC platform updates from Olof Johansson:
"Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: tango: Fix UP build issues
ARM: tango: pass ARM arch level for smc.S
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
ARM: tango4: Initial platform support
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
ARM: imx: select SRC for i.MX7
ARM: uniphier: select PINCTRL
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
...
