Jonathan writes:
"3rd set of IIO fixes for the 6.1 cycle.
Usual mixed bunch of driver fixes.
* sw-triggers
- Fix failure to cleanup up list registration in an error path.
* aspeed,adc
- Drop the trim valid dts property as it doesn't account for unprogrammed
OTP and that can be easily detected without it.
* avago,apds9960:
- Fix register address for gesture gain.
* bosch,bma400
- Fix a memory leak in an error path.
* rohm,rpr0521
- Fix missing dependency on IIO_BUFFER/IIO_TRIGGERED_BUFFER.
* ti,afe4403/4404
- Fix out of band read by moving reads down to where they are
used."
* tag 'iio-fixes-for-6.1c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
dt-bindings: iio: adc: Remove the property "aspeed,trim-data-valid"
iio: adc: aspeed: Remove the trim valid dts property.
iio: core: Fix entry not deleted when iio_register_sw_trigger_type() fails
iio: accel: bma400: Fix memory leak in bma400_get_steps_reg()
iio: light: rpr0521: add missing Kconfig dependencies
iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw
iio: health: afe4403: Fix oob read in afe4403_read_raw
iio: light: apds9960: fix wrong register for gesture gain
Xu writes:
FPGA Manager changes for 6.1-final
Intel m10 bmc secure update
- Russ's change fixes Kconfig dependencies
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-6.1 branch)
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-6.1-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: m10bmc-sec: Fix kconfig dependencies
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If PTP synchronisation is done every second, then sporadic the interval
is higher than one second:
ptp4l[696.582]: master offset -17 s2 freq -1891 path delay 573
ptp4l[697.582]: master offset -22 s2 freq -1901 path delay 573
ptp4l[699.368]: master offset -1 s2 freq -1887 path delay 573
^^^^^^^ Should be 698.582!
This problem is caused by rotten packets, which are received after
polling but before interrupts are enabled again. This can be fixed by
checking for pending work and rescheduling if necessary after interrupts
has been enabled again.
Fixes: 403f69bbdb ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20221119211825.81805-1-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When using dash as /bin/sh, the CC_HAS_ASM_GOTO_TIED_OUTPUT test fails
with a syntax error which is not the one we are looking for:
<stdin>: In function ‘foo’:
<stdin>:1:29: warning: missing terminating " character
<stdin>:1:29: error: missing terminating " character
<stdin>:2:5: error: expected ‘:’ before ‘+’ token
<stdin>:2:7: warning: missing terminating " character
<stdin>:2:7: error: missing terminating " character
<stdin>:2:5: error: expected declaration or statement at end of input
Removing '\n' solves this.
Fixes: 1aa0e8b144 ("Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). Call pci_dev_put() before returning from
bnx2x_vf_is_pcie_pending() to avoid refcount leak.
Fixes: b56e9670ff ("bnx2x: Prepare device and initialize VF database")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221119070202.1407648-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In former times, info->feature was populated via the parent driver
by pdata/regulator_init_data->driver_data for all regulators when
USB_PRODUCT_ID_LSB indicates a TWL6032.
Today, the information is not set, so re-add it at the regulator
definitions.
Fixes: 25d8233770 ("regulator: twl: make driver DT only")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221120221208.3093727-2-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code re-calculates the size after aligning the starting and
ending physical addresses on a page boundary. But the re-calculation
also embeds the masking of high order bits that exceed the size of
the physical address space (via PHYSICAL_PAGE_MASK). If the masking
removes any high order bits, the size calculation results in a huge
value that is likely to immediately fail.
Fix this by re-calculating the page-aligned size first. Then mask any
high order bits using PHYSICAL_PAGE_MASK.
Fixes: ffa71f33a8 ("x86, ioremap: Fix incorrect physical address handling in PAE mode")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/1668624097-14884-2-git-send-email-mikelley@microsoft.com
Neither Redpine Signals nor Silicon Labs seem to care about proper
maintenance of this driver, nor is there any help, documentation or
feedback on patches. The driver suffers from various problems and
subtle bugs. Mark it as orphaned.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221113185838.11643-1-marex@denx.de
When IPv6 module initializing in xfrm6_init(), register_pernet_subsys()
is possible to fail but its return value is ignored.
If IPv6 initialization fails later and xfrm6_fini() is called,
removing uninitialized list in xfrm6_net_ops will cause null-ptr-deref:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
CPU: 1 PID: 330 Comm: insmod
RIP: 0010:unregister_pernet_operations+0xc9/0x450
Call Trace:
<TASK>
unregister_pernet_subsys+0x31/0x3e
xfrm6_fini+0x16/0x30 [ipv6]
ip6_route_init+0xcd/0x128 [ipv6]
inet6_init+0x29c/0x602 [ipv6]
...
Fix it by catching the error return value of register_pernet_subsys().
Fixes: 8d068875ca ("xfrm: make gc_thresh configurable in all namespaces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Kernel 5.14 added a new "byseq" index to speed
up xfrm_state lookups by sequence number in commit
fe9f1d8779 ("xfrm: add state hashtable keyed by seq")
While the patch was thorough, the function pfkey_send_new_mapping()
in net/af_key.c also modifies x->km.seq and never added
the current xfrm_state to the "byseq" index.
This leads to the following kernel Ooops:
BUG: kernel NULL pointer dereference, address: 0000000000000000
..
RIP: 0010:__xfrm_state_delete+0xc9/0x1c0
..
Call Trace:
<TASK>
xfrm_state_delete+0x1e/0x40
xfrm_del_sa+0xb0/0x110 [xfrm_user]
xfrm_user_rcv_msg+0x12d/0x270 [xfrm_user]
? remove_entity_load_avg+0x8a/0xa0
? copy_to_user_state_extra+0x580/0x580 [xfrm_user]
netlink_rcv_skb+0x51/0x100
xfrm_netlink_rcv+0x30/0x50 [xfrm_user]
netlink_unicast+0x1a6/0x270
netlink_sendmsg+0x22a/0x480
__sys_sendto+0x1a6/0x1c0
? __audit_syscall_entry+0xd8/0x130
? __audit_syscall_exit+0x249/0x2b0
__x64_sys_sendto+0x23/0x30
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x61/0xcb
Exact location of the crash in __xfrm_state_delete():
if (x->km.seq)
hlist_del_rcu(&x->byseq);
The hlist_node "byseq" was never populated.
The bug only triggers if a new NAT traversal mapping (changed IP or port)
is detected in esp_input_done2() / esp6_input_done2(), which in turn
indirectly calls pfkey_send_new_mapping() *if* the kernel is compiled
with CONFIG_NET_KEY and "af_key" is active.
The PF_KEYv2 message SADB_X_NAT_T_NEW_MAPPING is not part of RFC 2367.
Various implementations have been examined how they handle
the "sadb_msg_seq" header field:
- racoon (Android): does not process SADB_X_NAT_T_NEW_MAPPING
- strongswan: does not care about sadb_msg_seq
- openswan: does not care about sadb_msg_seq
There is no standard how PF_KEYv2 sadb_msg_seq should be populated
for SADB_X_NAT_T_NEW_MAPPING and it's not used in popular
implementations either. Herbert Xu suggested we should just
use the current km.seq value as is. This fixes the root cause
of the oops since we no longer modify km.seq itself.
The update of "km.seq" looks like a copy'n'paste error
from pfkey_send_acquire(). SADB_ACQUIRE must indeed assign a unique km.seq
number according to RFC 2367. It has been verified that code paths
involving pfkey_send_acquire() don't cause the same Oops.
PF_KEYv2 SADB_X_NAT_T_NEW_MAPPING support was originally added here:
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
commit cbc3488685b20e7b2a98ad387a1a816aada569d8
Author: Derek Atkins <derek@ihtfp.com>
AuthorDate: Wed Apr 2 13:21:02 2003 -0800
[IPSEC]: Implement UDP Encapsulation framework.
In particular, implement ESPinUDP encapsulation for IPsec
Nat Traversal.
A note on triggering the bug: I was not able to trigger it using VMs.
There is one VPN using a high latency link on our production VPN server
that triggered it like once a day though.
Link: https://github.com/strongswan/strongswan/issues/992
Link: https://lore.kernel.org/netdev/00959f33ee52c4b3b0084d42c430418e502db554.1652340703.git.antony.antony@secunet.com/T/
Link: https://lore.kernel.org/netdev/20221027142455.3975224-1-chenzhihao@meizu.com/T/
Fixes: fe9f1d8779 ("xfrm: add state hashtable keyed by seq")
Reported-by: Roth Mark <rothm@mail.com>
Reported-by: Zhihao Chen <chenzhihao@meizu.com>
Tested-by: Roth Mark <rothm@mail.com>
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Antony Antony <antony.antony@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There is a race between modprobe and mount as below:
modprobe zonefs | mount -t zonefs
--------------------------------|-------------------------
zonefs_init |
register_filesystem [1] |
| zonefs_fill_super [2]
zonefs_sysfs_init [3] |
1. register zonefs suceess, then
2. user can mount the zonefs
3. if sysfs initialize failed, the module initialize failed.
Then the mount process maybe some error happened since the module
initialize failed.
Let's register zonefs after all dependency resource ready. And
reorder the dependency resource release in module exit.
Fixes: 9277a6d4fb ("zonefs: Export open zone resource information through sysfs")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Commit 1229b33973 ("ice: Add low latency Tx timestamp read") refactored
PTP timestamping logic to use a threaded IRQ instead of a separate kthread.
This implementation introduced ice_misc_intr_thread_fn and redefined the
ice_ptp_process_ts function interface to return a value of whether or not
the timestamp processing was complete.
ice_misc_intr_thread_fn would take the return value from ice_ptp_process_ts
and convert it into either IRQ_HANDLED if there were no more timestamps to
be processed, or IRQ_WAKE_THREAD if the thread should continue processing.
This is not correct, as the kernel does not re-schedule threaded IRQ
functions automatically. IRQ_WAKE_THREAD can only be used by the main IRQ
function.
This results in the ice_ptp_process_ts function (and in turn the
ice_ptp_tx_tstamp function) from only being called exactly once per
interrupt.
If an application sends a burst of Tx timestamps without waiting for a
response, the interrupt will trigger for the first timestamp. However,
later timestamps may not have arrived yet. This can result in dropped or
discarded timestamps. Worse, on E822 hardware this results in the interrupt
logic getting stuck such that no future interrupts will be triggered. The
result is complete loss of Tx timestamp functionality.
Fix this by modifying the ice_misc_intr_thread_fn to perform its own
polling of the ice_ptp_process_ts function. We sleep for a few microseconds
between attempts to avoid wasting significant CPU time. The value was
chosen to allow time for the Tx timestamps to complete without wasting so
much time that we overrun application wait budgets in the worst case.
The ice_ptp_process_ts function also currently returns false in the event
that the Tx tracker is not initialized. This would result in the threaded
IRQ handler never exiting if it gets started while the tracker is not
initialized.
Fix the function to appropriately return true when the tracker is not
initialized.
Note that this will not reproduce with default ptp4l behavior, as the
program always synchronously waits for a timestamp response before sending
another timestamp request.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Fixes: 1229b33973 ("ice: Add low latency Tx timestamp read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20221118222729.1565317-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-11-18 (iavf)
Ivan Vecera resolves issues related to reset by adding back call to
netif_tx_stop_all_queues() and adding calls to dev_close() to ensure
device is properly closed during reset.
Stefan Assmann removes waiting for setting of MAC address as this breaks
ARP.
Slawomir adds setting of __IAVF_IN_REMOVE_TASK bit to prevent deadlock
between remove and shutdown.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix race condition between iavf_shutdown and iavf_remove
iavf: remove INITIAL_MAC_SET to allow gARP to work properly
iavf: Do not restart Tx queues after reset task failure
iavf: Fix a crash during reset task
====================
Link: https://lore.kernel.org/r/20221118222439.1565245-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long says:
====================
tipc: fix two race issues in tipc_conn_alloc
The race exists beteen tipc_topsrv_accept() and tipc_conn_close(),
one is allocating the con while the other is freeing it and there
is no proper lock protecting it. Therefore, a null-pointer-defer
and a use-after-free may be triggered, see details on each patch.
====================
Link: https://lore.kernel.org/r/cover.1668807842.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One extra conn_get() is needed in tipc_conn_alloc(), as after
tipc_conn_alloc() is called, tipc_conn_close() may free this
con before deferencing it in tipc_topsrv_accept():
tipc_conn_alloc();
newsk = newsock->sk;
<---- tipc_conn_close();
write_lock_bh(&sk->sk_callback_lock);
newsk->sk_data_ready = tipc_conn_data_ready;
Then an uaf issue can be triggered:
BUG: KASAN: use-after-free in tipc_topsrv_accept+0x1e7/0x370 [tipc]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x178/0x4b0
kasan_report+0x8c/0x100
kasan_check_range+0x179/0x1e0
tipc_topsrv_accept+0x1e7/0x370 [tipc]
process_one_work+0x6a3/0x1030
worker_thread+0x8a/0xdf0
This patch fixes it by holding it in tipc_conn_alloc(), then after
all accessing in tipc_topsrv_accept() releasing it. Note when does
this in tipc_topsrv_kern_subscr(), as tipc_conn_rcv_sub() returns
0 or -1 only, we don't need to check for "> 0".
Fixes: c5fa7b3cf3 ("tipc: introduce new TIPC server infrastructure")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A crash was reported by Wei Chen:
BUG: kernel NULL pointer dereference, address: 0000000000000018
RIP: 0010:tipc_conn_close+0x12/0x100
Call Trace:
tipc_topsrv_exit_net+0x139/0x320
ops_exit_list.isra.9+0x49/0x80
cleanup_net+0x31a/0x540
process_one_work+0x3fa/0x9f0
worker_thread+0x42/0x5c0
It was caused by !con->sock in tipc_conn_close(). In tipc_topsrv_accept(),
con is allocated in conn_idr then its sock is set:
con = tipc_conn_alloc();
... <----[1]
con->sock = newsock;
If tipc_conn_close() is called in anytime of [1], the null-pointer-def
is triggered by con->sock->sk due to con->sock is not yet set.
This patch fixes it by moving the con->sock setting to tipc_conn_alloc()
under s->idr_lock. So that con->sock can never be NULL when getting the
con from s->conn_idr. It will be also safer to move con->server and flag
CF_CONNECTED setting under s->idr_lock, as they should all be set before
tipc_conn_alloc() is called.
Fixes: c5fa7b3cf3 ("tipc: introduce new TIPC server infrastructure")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currenty extended packet number (EPN) update routine is accessing
macsec object without holding the general macsec lock hence facing
a possible race condition when an EPN update occurs while updating
or deleting the SA.
Fix by holding the general macsec lock before accessing the object.
Fixes: 4411a6c0ab ("net/mlx5e: Support MACsec offload extended packet number (EPN)")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently updating SecY destroys and re-creates RX SA objects,
the re-created RX SA objects are not identical to the destroyed
objects and it disagree on the encryption enabled property which
holds the value false after recreation, this value is not
supported with offload which leads to no traffic after an update.
Fix by recreating an identical objects.
Fixes: 5a39816a75 ("net/mlx5e: Add MACsec offload SecY support")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently as part of MACsec SA initialization routine
extended packet number (EPN) object attribute is always
being set without checking if EPN is actually enabled,
the above could lead to a NULL dereference.
Fix by adding such a check.
Fixes: 4411a6c0ab ("net/mlx5e: Support MACsec offload extended packet number (EPN)")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Before the cited commit, for N channels, a dedicated set of N queues was
created to support XSK, in indices [N, 2N-1], doubling the number of
queues.
In addition, changing the number of channels was prohibited, as it would
shift the indices.
Remove these two leftovers, as we moved XSK to a new queueing scheme,
starting from index 0.
Fixes: 3db4c85cde ("net/mlx5e: xsk: Use queue indices starting from 0 for XSK queues")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit adds a for loop to support multiple encapsulations.
But it only checks if the last encap is valid.
Fix it by setting slow path flag when one of the encap is invalid.
Fixes: f493f15534 ("net/mlx5e: Move flow attr reformat action bit to per dest flags")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When sync reset now event handling fails on mlx5_pci_link_toggle() then
no reset was done. However, since mlx5_cmd_fast_teardown_hca() was
already done, the firmware function is closed and the driver is left
without firmware functionality.
Fix it by setting device error state and reopen the firmware resources.
Reopening is done by the thread that was called for devlink reload
fw_activate as it already holds the devlink lock.
Fixes: 5ec697446f ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit moved from using reformat_id integer to packet_reformat
pointer which introduced the possibility to null pointer dereference.
When setting packet reformat flag and pkt_reformat pointer must
exists so checking MLX5_ESW_DEST_ENCAP is not enough, we need
to make sure the pkt_reformat is valid and check for MLX5_ESW_DEST_ENCAP_VALID.
If the dest encap valid flag does not exists then pkt_reformat can be
either invalid address or null.
Also, to make sure we don't try to access invalid pkt_reformat set it to
null when invalidated and invalidate it before calling add flow code as
its logically more correct and to be safe.
Fixes: 2b688ea5ef ("net/mlx5: Add flow steering actions to fs_cmd shim layer")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case command interface is down, or the command is not allowed, driver
did not increment the entry refcount, but might have decrement as part
of forced completion handling.
Fix that by always increment and decrement the refcount to make it
symmetric for all flows.
Fixes: 50b2412b7e ("net/mlx5: Avoid possible free of command entry while timeout comp handler")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reported-by: Jack Wang <jinpu.wang@ionos.com>
Tested-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
While moving to new CMD API (quiet API), some pre-existing flows may call the new API
function that in case of error, returns the error instead of printing it as previously done.
For such flows we bring back the print but to tracepoint this time for sys admins to
have the ability to check for errors especially for commands using the new quiet API.
Tracepoint output example:
devlink-1333 [001] ..... 822.746922: mlx5_cmd: ACCESS_REG(0x805) op_mod(0x0) failed, status bad resource(0x5), syndrome (0xb06e1f), err(-22)
Fixes: f23519e542 ("net/mlx5: cmdif, Add new api for command execution")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When SF devices and SF port representors are located on different
functions, unloading and reloading of SF parent driver doesn't recreate
the existing SF present in the device.
Fix it by querying SFs and probe active SFs during driver probe phase.
Fixes: 90d010b863 ("net/mlx5: SF, Add auxiliary device support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix a bug in calculation of FW tracer timestamp. Decreasing one in the
calculation should effect only bits 52_7 and not effect bits 6_0 of the
timestamp, otherwise bits 6_0 are always set in this calculation.
Fixes: 70dd6fdb89 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Feras Daoud <ferasda@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The driver should not interact with PCI while PCI is disabled. Trying to
do so may result in being unable to get vital signs during PCI reset,
driver gets timed out and fails to recover.
Fixes: fad1783a6d ("net/mlx5: Print more info on pci error handlers")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
